Loading...
HomeMy WebLinkAboutSGD5470_20-0429.06 NOA No. 20-0429.06 Expiration Date: April 21, 2021 Approval Date: October 08, 2020 Page 1 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy PGT Industries, Inc. 1070 Technology Drive, North Venice, Fl. 34275 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Series “5470” Vinyl Sliding Glass Door (Reinforced)-N.I. APPROVAL DOCUMENT: Drawing No. SGD-5470 Rev B, titled “Vinyl Sliding Glass Door NOA (NI)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15 and revised on 04/22/20, signed and sealed by Anthony L. Miller, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami-Dade County Product Control Section. MISSILE IMPACT RATING: None: Applicable Hurricane Protection devices, complying w/ FBC, required. Limitations: 1. See table 1 (sheet 7) and table 2 (sheet 8) for applicable SGD unit sizes, design pressures, reinforcements types, glass types, sill riser (see tables B-1 & B-2, sheets 7-8) and anchor layout sheets requirements in 11 thru 16. 2. Rigid White PVC, Tan (Non-white) Rigid PVC and Brown coated (Painted or laminated) white Rigid PVC to be labeled per referenced NOA’s requirements. 3. Egress operable doors must comply with min clear width or height per FBC requirement, as applicable. 4. Pocket walls under separate approval, to be reviewed by Building official. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and series and following statement: "Miami-Dade County Product Control Approved", noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA #17-0420.07 and consists of this page 1, and evidence pages E-1, E-2, E-3 and E-4, as well as approval document mentioned above. The submitted documentation was reviewed by Ishaq I. Chanda, P.E. Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.06 Expiration Date: April 21, 2021 Approval Date: October 08, 2020 E - 1 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. Evidence submitted under previous NOA A. DRAWINGS 1. Manufacturer's die drawings and sections. (Submitted under NOA No. 11-0107.09) 2. Drawing No. SGD-5470, titled “Vinyl Sliding Glass Door NOA (NI)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15, with Revision A dated 04/05/17, signed and sealed by Anthony L. Miller, P.E. B. TESTS 1. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Forced Entry Test, per FBC, TAS 202-94 along with marked-up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 6637 (samples A-1 thru A-5), dated 11/19/10, signed and sealed by Jorge A. Causo, P. E.(Submitted under NOA No. 11-0107.09) 2. Additional test report No. FTL 6638 (samples A-1 thru A-22) per TAS 201/203-94, issued by Fenestration Testing Lab, Inc., dated 11/19/10, signed and sealed by Jorge A. Causo, P. E. (Submitted under NOA No. 11-0107.04) 3. Additional test report No. FTL 8717, issued by Fenestration Testing Lab, Inc., dated 12/07/15, revised on 02/15/16 and 02/24/16, signed and sealed by Idalmis Ortega, P. E. (Submitted under NOA No. 15-1210.01) 4. Additional test report No. FTL 8546 issued by Fenestration Testing Lab, Inc., dated 11/06/15, revised on 01/04/16 and 02/11/16, signed and sealed by Idalmis Ortega, P. E. (Submitted under NOA No. 15-1210.01) 5. Additional test report No. FTL 8547 issued by Fenestration Testing Lab, Inc., dated 12/04/15, revised on 02/15/16, signed and sealed by Idalmis Ortega, P. E. (Submitted under NOA No. 15-1210.01) 6. Additional test report No. FTL 8548 issued by Fenestration Testing Lab, Inc., dated 12/04/15, revised on 01/04/16 and 02/11/16, signed and sealed by Idalmis Ortega, P. E. (Submitted under NOA No. 15-1210.01) 7. Additional test report No. FTL 8549 issued by Fenestration Testing Lab, Inc., dated 12/04/15, revised on 12/04/15 and 02/11/16, signed and sealed by Idalmis Ortega, P. E. (Submitted under NOA No. 15-1210.01) 8. Additional test report No. FTL 8552 issued by Fenestration Testing Lab, Inc., dated 12/04/15, revised on 02/15/16, signed and sealed by Idalmis Ortega, P. E. (Submitted under NOA No. 15-1210.01). C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC-2014, prepared by PGT, dated 12/09/15 and last revised on 02/15/16, signed and sealed by Anthony L. Miller, P.E. (Submitted under NOA No. 15-1210.02). 2. Glazing complies with ASTME-1300-02, -04 & -09. Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.06 Expiration Date: April 21, 2021 Approval Date: October 08, 2020 E - 2 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED D. QUALITY ASSURANCE 1. Miami Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 15-0528.14 issued to Vision Extrusion Limited for their “White Rigid PVC Exterior Extrusions for Windows and Doors”, dated 08/13/15, expiring on 09/30/19. 2. Notice of Acceptance No. 16-0920.08 issued to Vision Extrusion Limited for their “VE 1000 Tan 202 and lighter Shades (Non-White) Rigid PVC Exterior Extrusions for Windows and Doors”, dated 12/08/16, expiring on 12/29/21. 3. Notice of Acceptance No. 15-0528.15 issued to Vision Extrusion Limited for their “Brown Coated (Painted or Laminated) White Rigid PVC Exterior Extrusions for Windows and Doors”, dated 08/13/15, expiring on 09/30/19. 4. Notice of Acceptance No. 16-0712.02 issued to ENERGI Fenestration Solutions USA, Inc. for their “TAN 3040 and Lighter Shades (Non-White) Rigid PVC Exterior Extrusions for Windows and Doors” dated 09/15/16, expiring on 02/04/21. 5. Notice of Acceptance No. 16-0712.04 issued to ENERGI Fenestration Solutions USA, Inc. for their “Bronze and Lighter Shades of Cap Coated Rigid PVC Exterior Extrusions for Windows and Doors” dated 09/15/16, expiring on 04/16/20. 6. Notice of Acceptance No. 16-0712.03 issued to ENERGI Fenestration Solutions USA, Inc. for their “White Rigid PVC Exterior Extrusions for Windows and Doors” dated 08/10/17, expiring on 02/28/18. 7. Test reports No(s). 10-002-792(A), 10-06-M0527, 535753-09, per ASTME-84, ASTMD1929 and ASTMD-635, issued by EXOVA to Vision Extrusion for cellulosic composite material. (Submitted under NOA No. 11-0107.04) F. STATEMENTS 1. Statement letter of conformance with FBC-5th Edition (2014) and FBC-6th Edition (2017), issued by manufacturer, dated 08/14/17, signed & sealed by Lynn Miller, P.E. 2. Statement letter of no financial interest, dated 04/18/17, issued by manufacturer, signed & sealed by Lynn Miller, P.E. 3. Letter of lab compliance, part of the above test reports. G. OTHER 1. Notice of Acceptance No. 15-1210.02, issued to PGT Industries, for their Series “5470” Vinyl Sliding Glass Door (Reinforced) – N.I.”, approved on 03/0316 and expiring on 04/21/21. 2. New Evidence Submitted A. DRAWINGS 1. Drawing No. SGD-5470 Rev B, titled “Vinyl Sliding Glass Door NOA (NI)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15 and revised on 04/22/20, signed and sealed by Anthony L. Miller, P.E. Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.06 Expiration Date: April 21, 2021 Approval Date: October 08, 2020 E - 3 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED B. TESTS 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along with marked-up drawings and installation diagram of all PGT Industries, Inc. representative units listed below and tested to qualify Dowsil 791 and Dowsil 983 silicones, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.: FTL-7897, PGT PW5520 PVC Fixed Window (unit 6 in proposal), dated 09/03/14 FTL-20-2107.1, PGT SGD780 Aluminum Sliding Glass Door (unit 7 in proposal) FTL-20-2107.2, PGT CA740 Alum. Outswing Casement Window (unit 8 in proposal) FTL-20-2107.3, PGT PW7620A Aluminum Fixed Window (unit 9 in proposal) and FTL-20-2107.4, PGT PW7620A Aluminum Fixed Window (unit 10 in proposal) dated 07/13/20, all signed and sealed by Idalmis Ortega, P.E. C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 7th Edition (2020), dated 04/22/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2. Glazing complies with ASTM E1300-04, -09, -12 and -16. D. QUALITY ASSURANCE Miami-Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for their “Trosifol® Ultraclear, Clear, and Color PVB Glass Interlayers”, expiring on 07/08/24. 2. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 3. Notice of Acceptance No. 18-1106.10 issued to Vision Extrusions Limited for their “Brown Coated (Painted or Laminated) White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 09/30/24. 4. Notice of Acceptance No. 18-1106.11 issued to Vision Extrusions Limited for their series “VE 1000 Tan 202 and lighter shades (Non–White) Rigid Cellular PVC Exterior Extrusions for Windows and Doors”, expiring on 12/29/21. 5. Quanex Part Super Spacer Standard complying with ASTM C518 Thermal Conductivity 0.881 BTU-in/ hr.-ft²-°F, ASTM F 1249 WVTR-Pass, ASTM D3985 Oxygen–Pass, ASTM E 2190 I.G. Durability-No Fog-Pass.(Submitted under previous NOA No. 15-0409.05). 6. Quanex Part Duraseal complying with ASTM C518 Thermal Conductivity 2.22 BTU-in/ hr.- ft²-°F, ASTM F 1249 WVTR-Pass, ASTM D 1434 Argon Permeance-Pass, ASTM E 2189 I.G. Durability-No Fog, ASTM E 546 Dew Point Development -20oF in 48 hrs.(Submitted under NOA No. 15-0409.05). Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.06 Expiration Date: April 21, 2021 Approval Date: October 08, 2020 E - 4 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED E. MATERIAL CERTIFICATIONS (continue) 7. Vision Extrusions, Ltd. Parts complying with PVC-AAMA 303-13, Voluntary Specification for Rigid Polyvinyl Chloride (PVC) Exterior Profiles for Vision Extrusions, Ltd.-VEX-1 by AAMA Fenestration Exterior Profile Certification Program. (Submitted under NOA No. 15- 0409.05). 8. Vision Extrusions, Ltd. Parts complying with PVC-AAMA 303-13. (Submitted under NOA No. 15-0409.05). 9. PVC-AAMA 303-13, Voluntary Specification for Rigid Polyvinyl Chloride (PVC) Exterior Profiles for Vision Extrusions, Ltd.-VEX-1 by AAMA Fenestration Exterior Profile Certification Program. 10. Notice of Acceptance No. 18-1217.14 issued to Energi Fenestration Solution, USA, Inc. for their “Tan 3040 & light shade (non-white) White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 02/04/21. 11. Notice of Acceptance No. 18-0122.02 issued to Energi Fenestration Solution, USA, Inc, for their series “White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 02/28/23. 12. Notice of Acceptance No. 20-0203.03 issued to Energi Fenestration Solution, USA, Inc. for their “Bronze & light shade cap coated White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 04/16/25. F. STATEMENTS 1. Statement letter of conformance to FBC 7th Edition (2020), dated 04/22/20, issued by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2. Statement letter of no financial interest and of independent, issued by manufacturer, dated 04/18/20, signed and sealed by Anthony Lynn Miller, P.E. G. OTHERS 1. This NOA revises NOA# 17-0420.07 and updates to FBC2020 (7th Edition), expiring 04/21/21. 2. RER Test proposals #19-1155 dated 01/10/20 approved by Ishaq I. Chanda, P.E.