HomeMy WebLinkAboutCertainTeed Landmark NEW MarkedM IAM I•QADE
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
CertainTeed Corporation
20 Moores Road
Malvern, PA 19355
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Landmark, Landmark Pro, Landmark Pro/Archetect 80, Landmark Premium, Landmark Impact
Resistant, Landmark Solaris, Landmark Pro Solaris and Landmark Solaris Gold/Platinum
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA # 17-1211.08 and consists of pages 1 through 7.
The submitted documentation was reviewed by Freddy Semino 0
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 1 of 7
ROOFING ASSEMBLY APPROVAL
Category:
Roofing
Sub -Category:
Asphalt Shingles
Materials
Dimensional
Deck Type:
Wood
SCOPE
This acceptance is for CertainTeed Landmark, Landmark Pro, Landmark Pro/Architect 80, Landmark
Premium, Landmark Impact Resistant, Landmark Solaris, Landmark Pro Solaris and Landmark Solaris
Gold/Platinum Shingles as manufactured by CertainTeed Corporation described in Section 2 of this Notice of
Acceptance.
PRODUCT DESCRIPTION:
Product
Test
Dimensions Snecifications Product Descrintion
Certainteed Landmark
Manufacturing Locations #1, 2, 3, 4, 5, 6, 7, 8, 9,
131/4" x 38 3/4"
TAS 110
A heavy weight, dimensional
10
asphalt shingle.
Certainteed Landmark Pro
A heavy weight, dimensional
Manufacturing Locations #1, 3, 4, 5, 6, 9, 10
131/4" x 38 3/4"
TAS 110
asphalt shingle.
Certainteed Landmark Premium
A heavy weight, dimensional
Manufacturing Locations #1, 3, 4, 5, 6, 8, 9
131/4" x 38 3/4"
TAS 110
asphalt shingle.
Certainteed Landmark Impact Resistant
A heavy weight, dimensional
Manufacturing Locations #7
131/4" x 38 3/4"
TAS 110
asphalt shingle.
Certainteed Landmark Pro/Architect 80
A heavy weight, dimensional
Manufacturing Locations #8
131/4" x 38 3/4"
TAS 110
asphalt shingle.
Certainteed Landmark Solaris
A heavy weight, dimensional
Manufacturing Locations #8, 9
131/4" x 38 3/4"
TAS 110
asphalt shingle.
CertainTeed Landmark Pro Solaris
A heavy weight, dimensional
Manufacturing Location #9
13'/4" x 38 3/4"
TAS 110
asphalt shingle
Certainteed Landmark Solaris Gold/Platinum
A heavy weight, dimensional
Manufacturing Locations # 8
131/4" x 38 3/4"
TAS 110
asphalt shingle.
Accessory Shingles
Accessory shingles for hip, ridge
various
proprietary
and starter strip applications.
MANUFACTURING LOCATIONS:
1. Peachtree City, GA
2. Ennis, TX
3. Oxford, NC
4. Shakopee, MN
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 2 of 7
5.
Avery (Milan), OH
6.
Norwood, MA
7.
Shreveport, LA
8.
Portland, OR
9.
Wilmington, CA
10.
Jonesburg, MO
EVIDENCE SUBMITTED:
Test Auncy
Test Identifier
Test Name/Report
Date
PRI Asphalt Technologies, Inc.
PCTC-01-02-01
TAS 100
01/12/01
CTC-006-02-01
TAS 100
11/12/02
CTC-092-02-01
TAS 100
02/23/12
CTC-091-02-01
TAS 100
02/21/12
CTC-090-02-01
TAS 100
09/02/11
CTC-087-02-01
TAS 100
07/07/11
CTC-086-02-01
TAS 100
07/07/11
CTC-101-02-01
TAS 100
10/05/11
CTC-102-02-01
TAS 100
10/05/11
CTC-109-02-01
TAS 100
01/18/12
CTC-106-02-01
TAS 100
11/02/11
CTC-105-02-01
TAS 100
10/31/11
CTC-089-02-01
TAS 100
07/18/11
CTC-088-02-01
TAS 100
07/18/11
CTC-213-02-01
TAS 100
05/20/14
CTC-212-02-01
TAS 100
05/21/14
CTC-207-02-01
TAS 100
05/20/14
CTC-206-02-01
TAS 100
05/20/14
CTC-110-02-01
TAS 100
02/13/12
CTC-109-02-01
TAS 100
02/13/12
CTC-288-02-01
TAS 100
09/27/16
CTC-333-02-01
TAS 100
11/08/17
Underwriters Laboratories, Inc.
94NK9632
Wind uplift resistance TAS 107
11/30/00
R684
UL 790
04/02/01
02NK42448
Wind uplift resistance TAS 107
11/08/02
09CA28873
Letter
07/23/09
11CA59020
TAS 107/ ASTM D3161
01/25/12
1 INK07864
TAS 107/ ASTM D3161
09/29/11
07CA26696
TAS 107/ ASTM D3161
09/21/07
I ICA38844
TAS 107/ ASTM D3161
01/28/12
I ICA38844
TAS 107/ ASTM D3161
01/27/12
06CA28237
TAS 107/ ASTM D3161
09/22/06
IONK17366
TAS 107/ ASTM D3161
01/04/11
4786334383
TAS 107/ ASTM D3161
05/28/14
4786307351 TAS 107/ ASTM D3161/ASTM D 3462 05/13/14
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 3 of 7
11NK08333
ASTM D3462
05/15/12
11NK08333
ASTM D3462
04/15/12
11NK07864
ASTM D3462
09/29/11
11NK08333/Letter
ASTM D3462 / UL790
11/05/12
11NK08333/Letter
ASTM D3462 / UL790
11/05/12
11NK08333/Letter
ASTM D3462 / UL790
11/05/12
12NK13474
ASTM D3462 / UL790
05/27/13
4786325932
ASTM D3462 / UL790
04/04/14
4787011023
ASTM D 3462
08/01/15
11CA38844
TAS 107/ ASTM D3161
01/26/12
06CA02648
TAS 107/ ASTM D3161
02/23/06
4787084802
TAS 107/ ASTM D3161
03/14/16
4787852839
ASTM D3462
03/24/17
4787011023
ASTM D3462
08/01/15
4788368979
ASTM D3462
10/30/18
4787592174
ASTM D3462
10/21/16
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. Shall not be installed on roof mean heights in excess of 33 ft.
3. All products listed herein shall have a quality assurance audit
in accordance with the Florida
Building Code
and Rule 61 G20-3 of the Florida Administrative Code.
INSTALLATION:
1. Shingles shall be installed in compliance with Roofing Application Standard RAS 115.
2. Flashing shall be in accordance with Roofing Application Standard RAS 115
3. The manufacturer shall provide clearly written application instructions.
4. Exposure and course layout shall be in compliance with Detail 'A', attached.
5. Nailing shall be in compliance with Detail 'B', attached.
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 4 of 7
LABELING:
1. Shingles shall be labeled with the Miami -Dade Product Control approved seal as seen below or the wording
"Miami -Dade County Product Control Approved".
BUILDING PERMIT REQUIREMENTS:
1. Application for building permit shall be accompanied by copies of the following:
1.1 This Notice of Acceptance.
1.2 Any other documents required by the Building Official or the applicable code in order to properly
evaluate the installation of this system.
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 5 of 7
SHINGLE LAYOUT
Eaves
LANDMARK, LANDMARK PRO, LANDMARK PRO/ARCHITECT SO, LANDMARK PREMIUM,
LANDMARK IMPACT RESISTANT, LANDMARK SOLARIS, LANDMARK PRO SOLARIS AND
LANDMARK SOLARIS GOLD/PLATINUM
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 6 of 7
DETAIL B
T=- 33 3A"
WIDE '
NAILING
AREA
12"
T-
5 5/8"
Exposure
ape
Nailing area for "low & standard slopes (from 2:12 to 21:12)
Nail between upper& lowernail lines.
14 3W 12"
1"
13 114"
7 112"
B"
LANDMARK, LANDMARK PRO, LANDMARK PRO/ARCHETECT 80,LANDMARK PREMIUM,
LANDMARK IMPACT RESISTANT, LANDMARK SOLARIS, LANDMARK PRO SOLARIS AND
LANDMARK SOLARIS GOLD/PLATINUM
(LOW AND STANDARD SLOPE
4"
LANDMARK, LANDMARK PRO, LANDMARK PRO/ARCHETECT 80, LANDMARK PREMIUM,
LANDMARK IMPACT RESISTANT, LANDMARK SOLARIS, LANDMARK PRO SOLARIS AND
LANDMARK SOLARIS GOLD/PLATINUM
(STEEP SLOPE
END OF THIS ACCEPTANCE
NOA No.: 18-1114.02
Expiration Date: 02/28/22
Approval Date: 05/09/19
Page 7 of 7