HomeMy WebLinkAboutpoduct approvalGo�Nn
DEPARTMEFiT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTIC9 OF ACCEPTANCE (NOA
Lomanco, Inc.
2101 Wesi Main Street
Jacksonville, AR 72078
MIAMI-DADE COU Y
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 08
Miami, Florida 33175-2 74
T (786) 315-2590 F (786) 315-2 99
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA E hall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this prod
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, t
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the ust
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami -Dade County Product Control Section that this product or material fails to meet the requiremer
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: OmniRidge Pro PR04-N and PR04-SWN Ridge Vent
TRI-BUILT® OmniRidge Pro PR04-N and PR04-SWN Ridge Vent
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the appli able building code negatively affecting the performance of this product.
.lMRDIIN TION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, me, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
sales, adve ising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
this NOA sl all be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and folk
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,
it shall be one in its entirety.
INSPECT ON: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA 18-1107.03 and consists of pages 1 through 4.
The submitled documentation was reviewed by Freddy Semino
NOA No.19-1217,
Expiration Date: 10/01L
Approval Date: 01/21
Page 1 o
ROOFIN COMPONENT APPROVAL
CateLory Roofing
Sub -Cate Ventilation
Materials: Plastic
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Test Product
roduct Dimensions Specification Description
Lomanco muiRidge Pro Length 4 Feet TAS-100(A) Low profile attic ridge vent for i.
PRO-4N and PR04-SWN Width 14 %2 Inches under ridge shingles.
Ridge Ven Height 1 Inch
TRI-BUILT®OmniRidge Length 4 Feet
Pro PR04 and PR04- Width 14 %2 Inches
SWN Ridgi Vent Height 1 Inch
MANI
1. J
LOCATIONS:
EVIDENCE SUBMITTED:
Test ALyencv
PRI Construction Materials Technologies
TAS-100(A) Low profile attic ridge vent for instal
under ridge shingles.
Test Name/Revort
TAS 100(A)
ASTM D 1929
ASTM D 635
ASTM D 2843
Test Identifier
Date
LOM-045-02-01
04/28/ 15
LOM-034-02-01
03/28/ 14
LOM-033-02-01
03/28/14
LOM-041-02-01
06/05/ 14
NOA No.19-1217.(
Expiration Date: 10/01/2
Approval Date: 01/23/2
Page 2 of
APPROVED APPLICATIONS
Tradena e: Lomanco OmniRidge Pro PR04-N and PR04-SWN Ridge Vent
TRI-BUILT a OmniRidge Pro PR04-N and PR04-SWN Ridge Vent
System Type: Mechanical attachment of ridge vent over asphalt shingle roof systems only.
Cutout: Truss Construction: Cut shall be 1-3/4" wide and 6" shorter at each end than the total
the ridge vent to be installed.
Ridge Pole Construction: Cut shall be 3-1/4" wide and 6" shorter at each end than the total
length of the ridge vent to be installed.
Installation: Starting from the end of the ridge, center ridge vent over the slot and fasten using approved i
shank nails at 12 inches on center in molded hole locations (ten nails per vent section). -
Ridge Shi gle: Install pre -manufactured or field -cut ridge shingles over the ridge vent in compliance with the
shingle manufacturer's Notice of Acceptance (NOA) and the installation instructions. Ring
shank nails shall be corrosion resistant and long enough to penetrate through the wood deck a
minimum of 3/16".
Net Free Area: Refer to manufacturers published literature.
LIMITA
1. Refer to applicable Building Codes for required ventilation.
2. This acceptance is for installations on asphalt shingle roof systems only.
3. Lomalico OmniRidge Pro PR04-N and PR04-SWN Ridge Vent
and TRI-BUILT ®OmniRidge Pro PR04-N and PR04-SWN Ridge Vent, shall not be installed on roof mean
heigh s greater than 33 feet.
4. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code an
Rule q, 1 G20-3 of the Florida Administrative Code.
5. All ap' roved products listed herein shall be labeled and shall bear the imprint or identifiable marking of the
manufacturer's name or logo and following statement: "Miami -Dade County Product Control Approved" or the
Miam -Dade County Product Control Seal as shown below.
APPROVED
APPROVED
NOA No. 19-1217
Expiration Date: 10/01,
Approval Date: 01/23,
Page 3 c
Lomanco OmniRidge Pro PR04-N and PR04-SWN Ridge Vent
TRI-BUILT®Omni Ridge Pro PR04-N and PR04-SWN Ridge Vent
i
a
�4 4
� z
r �
DETAIL DRAWING
END OF THIS ACCEPTANCE
NOA No.19-121 .04
Expiration Date: 10/0 /20
Approval Date: 01/2 /20
Page 4 f 4