The URL can be used to link to this page

Home My WebLink AboutProductData_Plates800-479-6832 | P.O. Box 7000 | Carlisle, PA 17013 | Fax: 717-245-7053 | www.carlislesyntec.com EXPERIENCE THE CARLISLE DIFFERENCE HP-X Fasteners™ and isoweld® Fastening Plates Overview Carlisle’s HP-X Fasteners are used in conjunction with TPO, PVC, and KEE HP isoweld Fastening Plates to secure Sure-Weld® TPO, Sure-Flex™ PVC, and Sure-Flex KEE HP rooﬁ ng membrane to 20-gauge (0.91 mm) or 22-gauge (0.76 mm) steel or wood decks (minimum 15 ⁄32" [12 mm] CDX plywood). HP-X Fasteners provide excellent driving performance, back-out and corrosion resistance, and pull-out values. The isoweld Fastening Plate is designed to attach TPO, PVC, or KEE HP rooﬁ ng membrane from the underside using the isoweld induction welding tool. Features and Beneﬁ ts »Fewer fasteners and plates needed than in conventional mechanically fastened systems »No perimeter sheets required »Faster dry-in time »Non-penetrating system »Symmetrical load distribution Installation 1. No pre-drilling is necessary for wood and steel decks; simply insert the HP-X Fastener through the isoweld plate and install with a standard clutch drive electric screw gun (0–2500 rpm). Optimum fastener performance is achieved when the fastener is installed perpendicular to the deck and into the top ﬂ utes. Follow isoweld system installation instructions to attach the membrane to the installed plate using the isoweld tool. 2. Keep insulation substrate and membrane clean. Any debris on top of the insulation substrate and/or membrane should be removed prior to initiating the bonding process. Use a leaf blower or broom to remove any debris from the membrane surface. 3. Keep magnets clean. If a metal shard or other debris from the roof sticks to the magnet, it can cause damage to the membrane surface in the weld area. Periodically ensure there are no contaminants on the bottom of the magnet. Review Carlisle speciﬁ cations and details for complete installation information. Precautions »Eye protection is recommended during installation. »Use care to avoid over-torquing the fastener. »Do not expose plates to sunlight for extended periods. Typical Properties and Characteristics Size – Inches (mm) Weight (kg) Thread Length – Inches (mm) Packaging Fasteners/Carton 2 (50) 20 lbs (9.1) Full 1,000 3 (80) 29 lbs (13.1) 3 (75) 1,000 4 (110) 38 lbs (17.2) 4 (100) 1,000 5 (130) 47 lbs (21.3) 4 (100) 500 6 (150) 56 lbs (25.4) 4 (100) 500 7 (175) 33 lbs (15.0) 4 (100) 500 8 (200) 38 lbs (17.2) 4 (100) 500 10 (250) 46 lbs (20.9) 4 (100) 500 12 (300) 55 lbs (24.9) 4 (100) 500 14 (355) 65 lbs (29.5) 4 (100) 500 Plates 3 1⁄8 (80)34 lbs (15.4) — 500 Steel Deck 22-Gauge or 20-Gauge Wood Deck Min. 15 ⁄32" Typical Pull-out Value 710 lbf (3158 N) 22-gauge 375 lbf (1668 N) Minimum Penetration ¾" (19 mm) 1" (25 mm) Maximum Penetration 4" (100 mm) 4" (100 mm) Typical Static Back-out 15.1 in lbs (1.7 N-m) N/A Typical Drill Times 1.5 seconds – 20-gauge N/A Typical properties and characteristics are based on samples tested and are not guaranteed for all samples of this product. This data and information is intended as a guide and does not reﬂ ect the speciﬁ cation range for any particular property of this product. 02.01.19 © 2019 Carlisle. WEB-ONLY: CST-7239 - “HP-X Fasteners and isoweld Plates Product Data Sheet” Carlisle, HP-X Fasteners, Sure-Flex, and Sure-Weld are trademarks of Carlisle. isoweld is a registered trademark of SFS Intec, Inc.