HomeMy WebLinkAboutEngineering • . 'yr So � t 4,� s
� V �
Beams&Uprights: y
In the event of a conflict with the values in this table and the site specific plan,the contractor must utili2e the more
stringent dimensions and/or member sizes between the site specific plan and the below applicable span,limitations
prior to ordering materials,fabrication and/or construction.
150 MPH
PRIMARY HEADER BEAM MEMBERS-OPEN COVERED PATIO-(No Screen Insert)
3"Pan Roof Span 3"Pan Roof Span 3"Pan Roof Span 3"Pan Roof Span 3"Pan Roof Span
Maximum Roof Span Maximum Roof Span Maximum Roof Span=10' Maximum Roof Maximum Roof Span=
SIZE =6'-0" =81-0" 0" Span=12'-0" 1V-0"
2 X 4 9'-0" 9'-0" 8'-0" 7'-0" 7'-0"
2 X 5 12'-0" 11'-0" 10'-0" 9'-0" 8'-0"
2 X 6 13'-0" 12'-0" ill-0" 11'-0" 10'-o"
2 X 7 15'-0" 141-0" 13'-0" 12'-0" Ill-o"
2 X 8 15'-0"* 151-0" 15'-0" 15'-0" 13'-0"
2 X 9 15'-0"* 15'-0"* 15'-0"* 15'-0"* 13'-0"
2 X 10 15'-0"* 15'-0"` 15'-0"* 15'-0"* 13'-0";
Coaumn size is 3 x 3 x 0125" 1 8"'unless noted otherwise with a max height of 9'-0"=CSR control<1.0.Larger span re larger column sae.
�� ! th { } rR Pa 9 n;
Knee Bracing:
Contractor shall provide knee bracing on 45 degree angle pursuant the attach detail sheet that specified size and
length requirements. Knee bracing on upright above super gutter intersection shall be connected to upright no more
than 6"above the super gutter.Knee brace size shall be a minimum of 2 x 2 for beam span of 15' max;2 x 3 for 30'
max;2 x 4 for beam span greater than 30'.
Intermediate/Header Beam:
Contractor is required to install a minimum 2 x 7 intermediate header beam supported with 3 x 3 column spaced at
10 feet(max)when insulated roof span exceeds 15 feet.
Patio Cover:
Contractor is required to install insulated roof covering pursuant to the Florida product approval specification.
Overhang shall be a maximum of P-0" along the side, 3'-0" along the front and 1/2" along the front interface
between the super gutter and the attached pool cage knee riser wall.
Edge Distance:
Contractor is required to install uprights to provide a 2"minimum clearance from edge of slab and/or footer.
4401 Vineland Road., Suite A6, Orlando, FL 32811. (P)407-734-1470 (F)407-734-1790
www.aluminumscreendesign.com
. ,yam, j -
Fma A,,t UPIA iv.U r
t, - 9
.
Structural Aluminum: _ IV)
Conform to latest edition of Florida Building Code and Aluminum Design Manual standard practice for=•aluminum
design. -
All aluminum shall be 6005-T5(E=10,000 ksi;Fy=35 ksi)with a minimum wall thickness of 0.046"
Splicing prohibited without prior approval as to location and type.
Burning of holes in aluminum members is prohibited.Any member with burned holes must be replaced.
Aluminum Protection:
Shall be pursuant FBC 2003.8.4. Aluminum surfaces in contact with dissimilar materials, lime-mortar, concrete, or
other masonry materials, shall be protected with powder coated or ESP paint or alkali-resistant coatings, such as
heavy-bodied bituminous paint or water-white methacrylate lacquer.
Screws:
Aluminum self-tapping screws shall conform to ASME B 18.6.4 specification.
Self—tapping screws shall meet the requirements of ADM J.5
Maximum fastener spacing shall not exceed(3+20t)where"t'is the member thickness in inches.
For roofing and siding connection, use minimum 412 screws for end and side laps spaced at 12" max for side lap
and end lap fasteners shall be no more than 2"from the end of overlapping sheets.
Bolts:
Bolts and other fasteners shall be aluminum, stainless steel, hot-dip or electro-galvanized steel. Double cadmium
plated steel bolts may also be used.Bolt holes diameter shall not exceed 1/16"larger than the bolt diameter and shall
be spaced at a minimum of 2.5 times the bolt diameter with minimum edge distance of 1.5 times the bolt diameter.
p g
Bolts shall meet the requirements of ADM J.3
Concrete
Conform to ACI 318,latest edition and ACI 301
Compressive Ultimate Strength(Minimum at 28 days)shall be 3000 psi
Exposed chamfer edges shall be 3/4"
Reinforcine Steel:
Conform to ACI 318 and 315,Latest edition
All reinforcement steel shall be ASTM A615 Grade 60.
Smooth dowels&ties shall be ASTM A185
Welded Wire Fabric shall be ASTM Al85 or A82(Flat sheet).
Deformed bar anchors shall be ASTM A496,Grade 70
Cover: Footing 3"
Washer:
Washers shall be used under bolt heads and under nuts.
Hole Alijznment:
Poor matching holes must be rejected. Contractor shall prevent holes from drifting and distort the metal. All chips
and foreign matter between contacting surfaces shall be removed before assembly.
4401 Vineland Road., Suite A6, Orlando, FL 32811. (P)407-734-1470 (F)407-734-1790
www.aluminumscreendesign.com
4!tj 04. K E. N D fig :
General Notes & Design Standards
(Unscreened Patio Room Enclosure)
The following are general design standards.More stringent design standards may be noted on the plans. In the event
of a conflict in plans and/or design standard dimensions and/or member sizes,the contractor must utilize the more
stringent dimensions and/or member sizes prior to ordering materials,fabrication and/or construction.
Design Codes:
Florida Building Code 2014(5'Edition)
Aluminum Design Manual 2010
ASCE 7-10
Design Loads:
Pursuant to FBC Chapters 16&20
Ultimate Wind:-150 MPH(FBC Table 2002.4) (45 psi
Risk Category:-See attach site specific plan sheet(FBC Table 1604.5)
Exposure Category: -See attach site specific plan sheet(FBC 1609.4.3)
Additional Load requirements:
Structural members supporting screened enclosures are designed for wind in both of two orthogonal directions using
the pressures given in Table 2002.4.Each primary member is also designed for a 300 pound load applied vertically
downward along any 1 foot of any member, not occurring simultaneously with wind load.In addition to wind
pressures, purlins is also be designed for a 200 pound load applied vertically downward along any 1 foot of any
member,not occurring simultaneously with wind load.
Design Basis:
Allowable Stress Design(ASD)=Allowable Strength Design(ASD)divide by safety factor
General Requirements:
Reproductions of contract drawings by contractor in lieu of preparation of shop drawings signifies acceptance of
information shown as correct and obligates himself to any expense,real or implied,arising from their use.
A change to the structural drawings due to the acceptance of alternates and/or substitutes is the responsibility of the
contractor and must be submitted to the engineer for approval.
The general contractor and each subcontractor shall review the approve construction plans in its entirety and verify
all existing conditions prior to the start of any work. All inconsistencies shall be reported to the designer and/or
structural engineer, if needed. Should contractor construct the premises in a fashion not consistent with the plans
prepared by the designer and/or structural engineer, or in any fashion, change the plans and drawing without the
review and approval from the designer and/or structural engineer. Then designer and/or structural engineer shall
bear no responsibility or liability for the construction of premises and accuracy of the drawings.
Foundation and Earthwork:
Applicable only when unsuitable soils are encountered.
When unsuitable soils are encountered as specified bearing strata,notify owner's representative/engineer.
Soil bearing capacity—2,000 psf Minimum
Provide neat excavation for footing and place concrete immediately after excavation and inspection.
Pump water from footing excavation if greater than one inch.
Compact all fill to 95%ASTM D698 density.
Unit soil weight=105 pcf
Internal angle of friction=30 degrees
Coeff. Of friction between footing and soil=0.5
4401 Vineland Road., Suite A6, Orlando, FL 32811. (P)407-734-1470 (F)407-734-1790
www.aluminumscreendesign.com
LUMINUM SCREEN. DESIGN
_..
1 r
z ! L i{.ls=rllit .`1 q oI"4 7', u 'f5.on Er, � tli4
*Ultimate Wind Speed (mph): 150 Exposed Category: C Risk Category: 'I
Screen Room:
Insulated ❑ Pan Roof❑
Fascia ❑ Wall: Block ❑ Conventional❑
Uprights -X Top Plate X Kick Plate
Pool Screen/Cage::'
Dome ❑ Gabler-] Mansard ❑
Gutter❑ Wall: Block❑ Conventional ❑ .
Beams X Uprights X Purlin X
Car Port:
Insulated ❑ Pan
Fascia ❑ Wall: Block ❑ Conventional ❑
Beams 2 X 7 Post 3 X 3
Patio Cover:
Insulated ❑ Pan ❑
Fascia ❑ Wall: Block[-] Conventional❑
Beams X Post X
Concrete:;
Existing New: 4" Slab❑ Pier❑Ribbon Footer x Pavers[]
Other:
Note: In the event that there is a conflict with the design plans and general notes and design standard,the contractor
shall utilize the more stringent dimensions and member sizes prior to ordering materials,fabrication and/or construction
between the plans and the general notes and design standard.
Engineer:Michael Thompson,MSc,P.E.(PE#47509)
4401 Vineland Road Suite A6,Orlando,FL 32811
(CA#30930)-Ph 407-734-1470/Fax 407-734-1790.
1 `
r
d W , E
y--,-I ..,. .>i Situ - '{. " 1 ^r IT,
l 1 ®g® �ry�"�'1
'1 � 5; p ice: •'t I r ':k
Fi 4 l 1 a
£_ a. _.F": �;;i mi J U`, r°� Itd. Cti(illC`f roTI.siCL'c !? SY7 � i33`:xstta
41 Irr4 r 7
Pr trf 14fl.v yl 4 �.. '.
*Plan Types: k
❑ Screen Room
❑ Pool Screen/Cage (Removable Screen - Remove screen when wind speed exceeds 75 MPH)
❑ Pool Screen/Cage (Non-Removable Screen — Designed to withstand actual Wind Speed)
❑✓ Car Port
❑ Patio Cover
❑ Other:
*Reference: QUINLAN New ✓ Revision Date:2/22/2017
*Project Address:
1 7932 Meadowlark Ln
*City:
Port St Lucie
*Contractor Name: WESCON CONSTRUCTION
*Address: 5130 Commercial Dr Suite H
'City: Melbourne
*Zip Code:32940
*Phone/Fax:321-259-6789
*Email: snovo@wescon.construction
Choose One: Mail❑ Pick lJp❑ Fed Ex*[— 2 No of Copies
*For Fed Ex option got to www.aluminumscreendesign.com and provide FedEx account#)
*Payment:; Check ❑ Credit Card *❑✓
*(For Credit Card option go to www.aluminumscreendesign.com to pay by credit card)
Engineering prepared by:
IL
Engineer: Michael Thompson, MSc, P.E.(P.E.#47509)
4401 Vineland Road—Suite A6,Orlando, FL 32811
Office:407-734-1470 Cell:407-721-2292
Project Manager: Paul Thomas 386-479-9504 Fax:888-923-8181
Email: aluminumscreendesign@yahoo.com
Website:www.aluminumscreendesign.com CA#30930
ou
.`
.rwy-\�
M-1,11E M. P00211rly OF (TIE
� �� �'�►-�s �, Ito � �
Gbe
ft1
.f
(��--Q 17 ors
Z� 3 3x3 �.vu„�►..�s w ��...
u s / xi pv-&-vimAlf
c.v W aAp
0
ASe
5-) 1,:o
ST.ILUCIF,COUNTY RUTYL PTIN DIVISION
DATE
P ANg riUNINll RMIT NnTST uE KEPT ON JOB
1;NO,LN,SPECTION WILL IrM MA_�.L.
3.,C CHANNEL IS ATTACHED TO BLOCK STRUCTURE WITH 2-1/4"X 1/4"TAPCONS
ALUMINUM SCREEN DESIGN
EXTRUDED GUTTER IS ATTACHED TO
3"INSULATED ROOF WITH#10 1"6" EXTRUDED FASCIA IS ATTACHED TO
FROM ENDS 24"O.C. 3"INSULATED ROOF WITH#10 1"6"
FROM ENDS 24"O.C.
,1 .
3X3 POSTS ARE ATTACHED
ROOF IS ATTACHED TO FRONT WALL TO 2X7 BEAM 2 3/8"X 3 1/2"
( WITH 4 #10 4"PER PANEL CARRIAGE BOLTS TYP.
BEAM TO WALL CONNECTION
2X2 RECIEVING CHANNEL IS
ATTACHED TO BEAM WITH
1 LESS#10 1"THEN BEAM SIZE
&INTO STRUCTURE WITH(4)#10 2"
3X3 POST IS ATTACHED TO
BRACKET WITH 1 3/8"X 3
1/2"CARRIAGE BOLTS
BRACKET FROM 3X3 IS ATTACHED
TO CONCRETE WITH 2 1/4"X 2"
TAPCONS TYP.
ALUMINUMSCREENDESIGN.COM DESIGN STATEMENT MICHAEI� PG} IPSQ
METAL IS.046 THICKNESS OR GREATER,ALLOY IS 6005-T5 4401 V IN$D NIS R'"AD
ALUMINUMSCREENDESIGN ALL TAPCONS SHALL PROVIDE MINIMUM OF 1 1/8"EMBEDMENT DEPTH y r 5
@YAHOO.COM � L1jTE
THIS STRUCTURE HAS BEEN DESIGNED IN ACCORDANCE TO MEET THE REQUIREMENTS OF THE 2014(5TH EDITION) OLAD 32811
PHONE: 407-747-1470 OF THE FLORIDA BUILDING CODE FOR OPEN AND SEMI-OPEN STRUCTURES AND SHALL WITH STAND ULTIMATE WIND 5 c r
SPEEDS OF 150 MPR(FOR 3 SECOND GUSTS)NOMINAL SPEED 117 MPH UP TO A 15FT ROOF HEIGHT,FACTOR OF 1.0,AND EXPOSURE C,RISK CATEGORY 1 h
FAX:407-734-1790 CONTRACTOR SHALL FIELD VERIFY ALL PLANS DIMENSIONS PRIOR TO MATERIAL PURCHASE,FABRICATION AND CONSTRUCTION _75 O9
CONTRACTOR SHALL NOTIFY THE ENGINEER IMMEDIATELY SHOULD SITE CONDITIONS DIFFER FROM CONSTRUCTION PLANS .--P6 L; 3 O
ROLL FORM FASCIA IS 3"C CHANNEL IS
D TO BLOCK STRUCTURE
ALUMINUM SCREEN DESIGN PAN ROOF WITH#10 1 6'F FROM ATTACHED TO 6"FROM ENDS 24"O.0&ITO 33"PAN ROOF WITH(4)10 1 T PER PANNEL1 TAPCONS
ENDS 24"O.C.
ROLL FORM GUTTER IS ATTACHED TO
3"PAN ROOF WITH#10 1"6"FROM ENDS 24"O.0
ROOF IS ATTACHED TO FRONT WALL 3"PAN ROOF IS ATTACHED TO
WITH 4 #10 2"PER PAN WOOD STRUCTURE WITH#10 2"
6"FROM ENDS 24"O.C.
t
EXISTING WOOD STRUCTURE
ALUMINUMSCREENDESIGN.COM DESIGN STATEMENT MICIATON
METAL IS.046 THICKNESS OR GREATER,ALLOY IS 6005-T5 4401`VL ROAD
ALUMINUMSCREENDESIGN ALL TAPCONS SHALL PROVIDE MINIMUM OF l 1/8"EMBEDMENT DEPTHE AE)
@YAHOO.COM ~
THIS STRUCTURE HAS BEEN DESIGNED IN ACCORDANCE TO MEET THE REQUIREMENTS OF THE 2014(STH EDITION) ORE-A k ,32811 y_
PHONE:407-747-1470 OF THE FLORIDA BUILDING CODE FOR OPEN AND SEMI-OPEN STRUCTURES AND SHALL WITH STAND ULTIMATE WIND
>
SPEEDS OF 150 MPH(FOR 3 SECOND GUSTS)NOMINAL SPEED 117 MPH UP TO A 15FT ROOF HEIGHT,FACTOR OF 1.0,AND EXPOSURE C,RISK CATEGORY 1 ? �a � s
FAX: 407-734-1790 CONTRACTOR SHALL FIELD VERIFY ALL PLANS DIMENSIONS PRIOR TO MATERIAL PURCHASE,FABRICATION AND CONSTRUCTION
CONTRACTOR SHALL NOTIFY THE ENGINEER IMMEDIATELY SHOULD SITE CONDITIONS DIFFER FROM CONSTRUCTION PLANS :` CA.#3'O93 O
EXTRUDED FASCIA IS
3"C CHANNEL IS
ALUMINUM SCREEN DESIGN 3' INSULATED ROOF WITH#10011'6T0 6"FROM ENDS 24"ATTACHED
CA&TEO 3T INSULATED ROOF STRUCTURE
T6 #10 1"PER 3IDE�S
FROM ENDS 24"O.C..
EXTRUDED GUTTER IS ATTACHED T
3"INSULATED ROOF WITH 410 1"6"
FROM ENDS 24"O.C.
ROOF IS ATTACHED TO FRONT WALL
WITH(4)#10 4"PER PANEL "INSULATED ROOF IS ATTACHED TO
ALUMINUM STRUCTURE WITH#10 4"
"FROM ENDS 24".O.C.
EXISTING SCREEN ROOM
r ,ti
ALUMINUMSCREENDESIGN.COM DESIGN STATEMENT MIC ., 1-.HOrvIP,SON
ALUMINUMSCREENDESIGN ALL TA METAL IS.046 THICKNESS OR GREATER,ALLOY IS 6005-T5 4401INEILAN� tOAD
PCONS SHALL PROVIDE MINIMUM OF 1 1/8"EMBEDMENT DEPTH a m
@Q YAHOO.COM THIS STRUCTURE HAS BEEN DESIGNED IN ACCORDANCE TO MEET THE REQUIREMENTS OF THE,2014(5TH EDITION)
OF THE FLORIDA BUILDING CODE FOR OPEN AND SEMI-OPEN STRUCTURES AND SHALL WITH STND ULTIMATE WIND ORLAdi L
PHONE: 407-747-1470 SPEEDS OF 150 MPH(FOR 3 SECOND GUSTS)NOMINAL SPEED 117 MPH UP TO A 15FT ROOF HEIGHT,FACTOR OF 1.0,AND EXPOSURE C,RISK CATEGORY 1
FAX: 407-734-1790 CONTRACTOR SHALL FIELD VERIFY ALL PLANS DIMENSIONS PRIOR TO MATERIAL PURCHASE,FABRICATION AND CONSTRUCTION
CONTRACTOR SHALL NOTIFY THE ENGINEER IMMEDIATELY SHOULD SITE CONDITIONS DIFFER FROM CONSTRUCTION PLANS CA#3.093.0
F