The URL can be used to link to this page

Home My WebLink AboutAPPROVED, HR7710NOAMIAMI•DADE I MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.2ov/economy PGT Industries, Inc. 1070 Technology Drive North Venice, FL 34275 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami —Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. - DESCRIPTION: Series "HR7710A" Aluminum Horizontal Roller Window — L.M.I. APPROVAL DOCUMENT: Drawing No. 7710NOA-1, titled "Aluminum Horiz. Roller Install (LM)", sheets 1 through 19 of 19, dated 06/30/18, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E., bearing the Miami -Dade County Product Control Approval stamp with the Notice of Acceptance number and approval date by the Miami -Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, model/series, and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERbIINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA consists of this page 1 and evidence pages E-1 and E-2, as well as approval document mentioned above. The submitted documentation was reviewed by Manuel Perez, P.E. NOA No. 18-0627.01 Expiration Date: August 23, 2023 Approval Date: August 23, 2018 Y81, Page 1 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED A. DRAWINGS 1. Manufacturer's die drawings and sections. 2. Drawing No. 7710NOA-1, titled "Aluminum Horiz. Roller Install (LM), sheets 1 through 19 of 19, dated 06/30/18, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. B. TESTS 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC 2411.3.2.1, and TAS 202-94 along with marked -up drawings and installation diagram of an aluminum horizontal sliding window, prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL-18-7891, dated 06/06/18, signed and sealed by Idalmis Ortega, P.E. 2. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC 2411.3.2.1, and TAS 202-94 along with marked -up drawings and installation diagram of an aluminum horizontal sliding window, prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL-18-7891.01, dated 07/03/18, signed and sealed by Idalmis Ortega, P.E. C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 61h Edition (2017), dated 06/18/18 and updated on 07/25/18, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2. Glazing complies with ASTM E1300-09 D. QUALITY ASSURANCE 1. Miami -Dade Department of Regulatory and Economic Resources (RER). Manuel er z, P.E. Product Contr 1 Examiner NOA N 0627.01 Expiration Date: August 23, 2023 Approval Date: August 23, 2018 E-1 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 17-1114.14 issued to Kuraray America, Inc. for their "Trosifol® Ultraclear, Clear and Color PVB Glass Interlayers" dated 01/18/18, expiring on 07/08/19. 2. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc, for their "SentryGlas® (Clear and White) Glass Interlayers" dated 12/28/17, expiring on 07/04/23. F. STATEMENTS 1. Statement letter of conformance to FBC 6th Edition (2017), dated July 25, 2018, issued by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2. Statement letter of no financial interest, dated July 25, 2018, issued by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 3. Proposal No. 18-0289 issued by the Product Control Section, dated 02/20/18, signed by Manuel Perez, RE G. OTHERS 1. None E-2 Manuel Pe ez P.E. Product Control - xa iner N( No. 1 627.01 Expiration Date: August 23, 2023 Approval Date: August 23, 2018 SERIES HR7710A IMPACT RESISTANT HORIZONTAL ROLLER WINDOW FOR ANCHOR 1) THIS PRODUCT HAS BEEN DESIGNED & TESTED TO COMPLY WITH THE REQUIREMENTS OF THE QUANTITIES, 12" _ FLORIDA BUILDING CODE, INCLUDING THE HIGH VELOCITY HURRICANE ZONE (HVHZ). SEE TABLES 12-14 23" �� O.C. 9" �) O.C. B 2) SHUTTERS ARE NOT REQUIRED WHEN USED IN WIND-BORNE DEBRIS REGIONS. FOR INSULATED GLASS i \ I INSTALLATIONS ABOVE 30' IN THE HVHZ, THE OUTBOARD LITE (CAP) MUST BE TEMPERED. 3) FOR MASONRY APPLICATIONS IN MIAMI-DADE COUNTY, USE ONLY MIAMI-DADE COUNTY APPROVED MASONRY ANCHORS. MATERIALS USED FOR ANCHOR EVALUATIONS WERE SOUTHERN PINE, ASTM C90 CONCRETE MASONRY UNITS AND CONCRETE WITH MIN. KSI PER ANCHOR TYPE. 4) ALL WOOD BUCKS LESS THAN 1-1/2" THICK ARE TO BE CONSIDERED 1X INSTALLATIONS. 1X WOOD BUCKS ARE OPTIONAL IF UNIT IS INSTALLED DIRECTLY TO SUBSTRATE. WOOD BUCKS DEPICTED AS 2X ARE 1-1/2" THICK OR GREATER. 1X AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED AND SECURED TO PROPERLY TRANSFER LOADS TO THE STRUCTURE. WOOD BUCK DESIGN AND INSTALLATION IS THE RESPONSIBILITY OF THE ENGINEER, (EOR) OR ARCHITECT OF RECORD, (AOR). 5) ANCHOR EMBEDMENT TO BASE MATERIAL SHALL BE BEYOND WALL DRESSING OR STUCCO. USE ANCHORS OF SUFFICIENT LENGTH TO ACHIEVE REQUIRED MIN. EMBEDMENT. SILL ANCHORS MUST BE SEALED. OVERALL SEALING & FLASHING STRATEGY FOR WATER RESISTANCE OF INSTALLATION SHALL BE DONE BY OTHERS AND IS BEYOND THE SCOPE OF THESE INSTRUCTIONS. 6) 1/4" MAX. SHIMS ARE REQUIRED AT EACH ANCHOR LOCATION WHERE THE PRODUCT IS NOT FLUSH TO THE SUBSTRATE. USE SHIMS CAPABLE OF TRANSFERRING APPLIED LOADS. 7) DESIGN PRESSURES: A. NEGATIVE DESIGN LOADS BASED ON STRUCTURAL & CYCLE TESTING AND GLASS PER ASTM El300. B. POSITIVE DESIGN LOADS BASED ON WATER TEST PRESSURE, STRUCTURAL & CYCLE TESTING AND GLASS PER ASTM El300. C. DESIGN LOADS ARE BASED ON ALLOWABLE STRESS DESIGN, ASD. A 76" OVERALL HEIGHT 75" BUCK HEIGHT SEE WEEPHOLE NOTES THIS SHEET A 69" / 69" / 1 SASH FIXED VISIBLE VISIBLE — LIGHT / LIGHT / 221l2" O.C. 3 T SASH 34-3/8" FIXED It VISIBLE VISIBLE LIGHT LIGHT DESIGN PRESSURE RATING IMPACT RATING VARIES PER GLASS TYPE, SEE TABLES 2-11 LARGE & SMALL MISSILE IMPACT RESISTANT 9" MAX. B (8-1/2" 75" BUCK WIDTH MAX. 76" OVERALL WIDTH BUCK) TYP. FLANGE XO ELEVATION (OX SIM MAX. DIMENSIONS ALLOWED SHOWN 8) THE ANCHORAGE METHODS SHOWN HAVE BEEN DESIGNED TO RESIST THE WINDLOADS FOR ANCHOR CORRESPONDING TO THE REQUIRED DESIGN PRESSURE. THE 33-1/3% STRESS INCREASE HAS NOT BEEN QUANTITIES, USED IN THE DESIGN OF THIS PRODUCT. THE 1.6 LOAD DURATION FACTOR WAS USED FOR THE SEE TABLES 15-18 12" EVALUATION OF ANCHORS INTO WOOD. ANCHORS THAT COME INTO CONTACT WITH OTHER DISSIMILAR 22-1/2" O.C. i MATERIALS SHALL MEET THE REQUIREMENTS OF THE FLORIDA BUILDING CODE FOR CORROSION 12" O.C. RESISTANCE. O.C. ----- ---II I\ / I \ I \ 9) METAL SUBSTRATE TO MEET MIN. STRENGTH AND THICKNESS REQUIREMENTS PER CURRENT FLORIDA BUILDING CODE AND TO BE REVIEWED BY THE AUTHORITY HAVING JURISDICTION. 10) REFERENCES: TEST REPORTS FTL 18-7891 & 18-7891.01; ELCO ULTRACON NOA; ELCO CRETEFLEX NOA; NATIONAL DESIGN SPECIFICATION FOR WOOD CONSTRUCTION, ANSI/AF&PA NDS & ALUMINUM DESIGN MANUAL 11) APPLICABLE EGRESS REQUIREMENTS TO BE REVIEWED BY BUILDING OFFICIAL. FwAft IIM Glass Type Description (Listed from Exterior to Interior) DP Table # Anchor Table # XO / OX XOX XO/ OX XOX STD HD I STD STD HD STD 1 1/8"AN, .090" PVB, 1/8" AN 2 7 12 15 2 1/8" HS, .090" PVB, 1/8" HS 3 8 12 16 3 3/16" AN, .090" PVB, 3/16" AN 3 - 8 12 16 4 13/16" LIG: 1/8" AN CAP, AIRSPACE, 1/8" AN, .090" PVB, 1/8" AN 4 - 7 12 - 15 5 13/16" LIG: 1/8" TP CAP, AIRSPACE, 1/8" AN, .090" PVB, 1/8" AN 3 - 7 12 15 6 13/16" LIG: 3/16" AN CAP, AIRSPACE, 1/8" AN, .090" PVB, 1/8" AN 3 9 12 16 7 13/16" LIG: 3/16" TP CAP, AIRSPACE, 1/8" AN, .090" PVB, 1/8" AN 3 9 12 16 8 3/16" AN, .090" SG, 3/16" AN 5 6 10 13 14 17 9 3/16" HS, .090" SG, 3/16" HS 5 6 11 13 14 18 10 13/16" LIG: 1/8" AN CAP, AIRSPACE, 3/16" AN, .090" SG, 3/16" AN 5 6 10 13 14 17 11 13/16" LIG: 1/8" TP CAP, AIRSPACE, 3/16" AN, .090" SG, 3116" AN 5 6 10 13 14 17 12 13/16" LIG: 1/8" AN CAP, AIRSPACE, 1/8" HS, .090" SG, 1/8" HS 5 6 11 13 14 18 13 13/16" LIG: 1/8" TP CAP, AIRSPACE, 1/8" HS, .090" SG, 1/8" HS 5 6 11 13 14 18 14 13/16" LIG: 3/16" AN CAP, AIRSPACE, 1/8" HS, .090" SG, 1/8" HS 1 5 6 11 13 14 18 15 13/16" LIG: 3/16" TP CAP, AIRSPACE, 1/8" HS, .090" SG, 1/8" HS 1 5 6 11 13 14 18 SG= KURARAY SENTRYGLAS® INTERLAYER BY KURARAY AMERICA, INC. PVB = KURARAY TROSIFOL® PVB INTERLAYER BY KURARAY AMERICA, INC. AN = ANNEALED HS = HEAT -STRENGTHENED TP = TEMPERED USER INSTRUCTIONS: 1) DETERMINE THE SITE SPECIFIC, WINDOW OPENING'S DESIGN PRESSURE REQUIREMENT FROM ASCE 7. 2) KNOWING YOUR GLAZING OPTION (TABLE 1), WINDOW CONFIGURATION AND SIZE, DETERMINE YOUR WINDOW'S DESIGN PRESSURE FROM TABLES 2-11. IT MUST EQUAL OR EXCEED THE DESIGN PRESSURE REQUIREMENT FOR THE WINDOW OPENING OBTAINED IN STEP 1. 3) DETERMINE THE ANCHOR QUANTITY FROM TABLES 12-18. 4) INSTALL AS PER SHEET 15 FOR FLANGE INSTALLATION, SHEET 16 FOR EQUAL LEG INSTALLATION OR SHEET 17 FOR INTEGRAL FIN INSTALLATION. NOTE: DESIGN PRESSURE RATING DETERMINATION IS THE SAME PROCESS FOR ALL FRAME TYPES (FLANGE, INTEGRAL FIN OR EQUAL LEG/BOX). WEEPHOLE NOTES: 1) 1-5/8" X .300" WITH PLASTIC BAFFLE. 2) 1 WEEPHOLE LOCATED AT 4" FROM EACH END. 3) 1 WEEPHOLE LOCATED UNDER EACH MEETING RAIL. 56 C 56" / " C 6SASH FIXED OVERALL / VISIBLE / VISIBLE / LIGHT LIGHT HEIGHT 22 1 /2" 62" O.C. BUCK 34" 55-3/8" FIXED HEIGHT SASH VISIBLE LIGHT VISIBLE I LIGHT 91, SEE SHEET 17 FOR INTEGRAL FIN ANCHORAGE TYPE TYP. FL & SPACING MAX. DI gel SEE WEEPHOLE NOTES, 119" BUCK WIDTH THIS SHEET 120" OVERALL WIDTH ANGE XOX ELEVATION MENSIONS ALLOWED SHOWN CODES / STANDARDS USED •2017 FLORIDA BUILDING CODE (FBC), 6TH EDITION *ASTM E1300-09 •ANSI/AF&PA NDS-2015 FOR WOOD CONSTRUCTION *ALUMINUM DESIGN MANUAL, ADM-2015 •AISI S100-12 •AISC 360-10 GENERAL NOTES..................................1 ELEVATIONS..........................................1 GLASS TYPES TABLE ...........................1 DESIGN PRESSURES ........................... 2-9 ANCHOR QUANTITIES ...................... .... 10-14 INSTALLATION / ANCHOR SPECS.... ... 15-17 EXTRUSION PROFILES ........................ 18 CORNER ASSEMBLY ............................19 PARTS LIST............................................19 ao W z O to nab W M C) O o � o (n O a}Dp I` � C� N zL QI O OYi J � �^ U)ZC Z O J O aU) Z LL W O cOp = W/5 wV 00 O J ¢ J F_ UMDlp OW OM0 O d a_ Z Z _ O o LU J J Q W rn 0 J W O � °2S ® rn N 0� LU aays LU D == O Z Q LL O J O Z X w 2i W � U Z Q _ w al}il -asap sauas \\ %l IIII///// ov LYN&�i _ No. 58705 STATE OF 0RIDP /lllllll A. LYNN MILLER, P.E. P.E.# 58705 Overall Width Glass Type: 1 Design Pressure (Ibs/ft2) for XO & OX Windows Meeting Rail: Standard 22-1/8" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 1 55" Overall Hgt. 1 63" Overall Hgt. 20" +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 25" +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 37" +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 49" +65.0 1 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 61" +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 67" +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 +65.0 -65.0 74" 11 +65.0 -65.0 +65.0 1 -65.0 +65.0 -65.0 1 +65.0 -65.0 +63.3 -63.3 Overall Width Glass Types: 2, 3, 5, 6, 7 Design Pressure (Ibs/ft2) for XO & OX Windows Meeting Rail: Standard 22-1/8" Overall Hgt. 37" Overall Hgt. 1 49" Overall Hgt. 1 55" Overall Hgt. 1 63" Overall Hgt. 20" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 25" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 37" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 49" 1 +65.0 1 -80.0 +65.0 -80.0 +65.0 1 -80.0 +65.0 -80.0 +65.0 -80.0 61 " +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 67" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -79.2* 74" +65.0 -80.0 +65.0 -80.0 1 +65.0 -80.0 +65.0 -80.0 +65.0 -72.2* -oU.0 rIJR VLmoo 1 1 rLJ G' J, V - , NOTES 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN, FOR INTEGRAL FIN AND EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. GLASS .090" PVB �1/8"AN 1/8" AN GLASS 30 24 GLASS BITE EXTERIOR 74 32 GLASS TYPE 1 .090" PVB 1/8" HS GLASS 1/8" HS GLASS 24 30 1/2" NOM. GLASS BITE EXTERIOR 1 a 74 32 GLASS TYPE 2 13/16" NOM. GLASS STACK AIRSPACE 090" PVB 1 /8" TEMPERED 1 /8" AN GLASS GLASS 31 74 1AOR 1B 1/2" NOM. GLASS BITE �� V 70-73 33A OR 336 V GLASS TYPE 5 V' 3/16" AN GLASS .090" PVB 30 3/16" ANGLASS 23 1/2" NOM. GLASS BITE EXTERIOR a 74 32 13/16" NOM. GLASS STACK AIRSPACE .090" PVB 3/16" AN OR TP GLASS 1 /8" AN GLASS 31 74 1A OR 1B � 1/2" NOM. l ( GLASS BITE 33A OR 33B GLASS TYPE 6 (ANNEALED) GLASS TYPE 7 (TEMPERED) LI J > ? o cn 'Aaa W w M 0 0 o O cp } ti U' CV o O Q a}oQ z OJ cM (DO Z O Z O J Z LL O 0 IL cn °p = J W = LLI o `' r, U I. 00Ljj J J UM Dl� >� U) z 0 oa Z W J Wrn coLL o o rn F LU N ® rn N W c 2 O U) aayS ~ = W O LLd O Z_ Z (D w ' U J W rY = 0011 �s�aQ sauaS LYN No.58705 %0�' . STAT O (V�� '/S'ONAL 1E� A. LYNN MILLER, P.E. P.E.# 58705 TARI C A Overall Width Pressure Design Ibs/ft2 for XO & OX Windows Glass Type: 4 g ( ) Meeting Rail: Standard 22-1/8" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 1 63" Overall Hgt. 20" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 25" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 37" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 49" +65.0 1 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 6111 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -76.8 67" +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -71.3 74" 11 +65.0 -80.0 +65.0 1 -80.0 +65.0 -80.0 +65.0 -77.1 +64.9 -64.9 Overall Width Glass Types: 8 thru 15 Design Pressure (Ibs/ft2) for XO & OX Windows Meeting Rail: Standard 22-1/8" Overall Hgt. 37" Overall Hgt. 1 49" Overall Hgt. 55" Overall Hgt. 1 63" Overall Hgt. 20" +80.0 1 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 25" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 37" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 49" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 61" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -101.9* 67" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -95.7* 74" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -90.0* .. --I -I U.0 iUK ULHJJ 1 T YCJ 7, 14, 10, 14 Oc I J 'GLASS TYPES 8 - 15 MAY NOT BE USED WITH INTEGRAL FIN • FRAMES NOTES: 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR INTEGRAL FIN AND EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. _ j 13/16" NOM. GLASS STACK AIRSPACE .090" PVB 1/8" AN GLASS 1/8" AN GLASS 31 74 1�OR 1 B 1/2" NOM. GLASS BITE � 6 u 70-73 33A OR 33B GLASS TYPE 4 .090" SG 30 EXTERIOR _3/16" AN OR HS GLASS 3/16" AN OR HS GLASS 1 1/2" NOM. GLASS BITE 74 32 GLASS TYPE 8 (ANNEALED) GLASS TYPE 9 (HEAT STRENGTHENED AIRSPACE 1 /8" AN OR _ TP GLASS 31 1AOR 1B 13/16" NOM. GLASS STACK ��090" SG /8" HS GLASS 74 AIRSPACE 1 /8" AN OR _ TP GLASS 31 1AOR *- EXTERIOR a 13/16" NOM. GLASS STACK ��.090" SG 3/16" AN GLASS 74 1/2" NOM. GLASS BITE 70-73 33A OR 336 GLASS TYPE 10 (ANNEALED) GLASS TYPE 11 (TEMPERED) ,,/ 13/16" NOM. GLASS STACK AIRSPACE .090" SG 3/16" AN OR TP GLASS 1/8" HS GLASS 31 74 1/2" NOM. 1A OR" B 1/2" NOM. GLASS BITE GLASS BITE \ e�J U 70-73 33A OR; GLASS TYPE 12 (ANNEALED) GLASS TYPE 13 (TEMPERED), 33 OR 33B-7 1 70-73 GLASS TYPE 14 (ANNEALED) GLASS TYPE 15 (TEMPERED) co Y LU > ? O (A na-a viw coM p O �o > > O O ' a}oa U N O z cwn �Uj U) O z 0 J z O a- U) `°= W O W r N v ti 48 WU W z b � J ¢ J J L1MOJ� 'ON C=7 9MQ O � p a o (n z z U 0-1 W J W J cy) < O rn LU `r' ® m N N = O U) aays F = W O d O) W z_ z ti ' U J W = a 19c] sauag �\1 LYNN�' No.58705 l 441 TATE OF (� A. LYNN MILLER, P.E. P.E.# 58705 Overall Width Design Pressure (Ibs/ft2Glass Types: 8 thru 15) for XO & OX Windows Meeting Rail: Heavy -Duty 22-1/8" Overall Hgt. 37" Overall Hgt. 1 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. 76" Overall Hgt. 20" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 25" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 37" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 49" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 61" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 67" +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -109.8* 76" +80.0 -110.0 +80.0 1 -110.0 +8&0 -110.0 +80.0 1 -110.0 +80.0 -110.0 +80.0 -105.8* .090" 30 23 EXTERIOR a 3a _3/16" AN OR HS GLASS 3116" AN OR HS GLASS 1 1/2" NOM. GLASS BITE GLASS TYPE 8 GLASS TYPE 9 74 AIRSPACE 1 /8" AN OR _ TP GLASS 31 1AOR 1B EXTERIOR a� _ 13/16" NOM. a GLASS STACK ��090" SG 6" ANGLASS - , 74) 1/2" NOM. GLASS BITE "-I IU.0 t-VK ULAJJ 1 YrtJ 25-1.9 & 10 AIRSPACE 1/8"AN OR TP GLASS 31 1AOR 1B a GLASS TYPES 8 - 15 MAY NOT BE USED WITH INTEGRAL FIN • FRAMES 13/16" NOM. GLASS STACK %090" SG 1/8" HS GLASS 74 1/2" NOM. GLASS BITE 70-73 70-73 33A OR 33B 33A OR 33B GLASS TYPE 10 (ANNEALED) GLASS TYPE 12 (ANNEALED) GLASS TYPE 11 (TEMPERED) _V GLASS TYPE 13 (TEMPERED), NOTES: 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE AIRSPACE 3/16" AN OR _ TP GLASS 31 1�OR 1 B EXTERIOR a 33A OR 33B GLASS TYPE 14 GLASS TYPE 15 13/16" NOM. GLASS STACK 090" SG 1/8" HS GLASS 74 1/2" NOM. GLASS BITE 70-73 ,NNEALED) EMPERED) O W ? (>n U) O t� > 7a� 0 �o w m O O (n U) O r ' a}oa C� N z N 0 O O M � Uj cn Z r) J LL O a co aO = W O Z LV cOp _j WU 00 J _j UMOJj OM Z It Q > � x p a Z Z o U Q� W -j J W J m O LL O Q O ® rn N W N aa4S = O U) D = W U_ O O C) _Z Z ti w ' U W _j = Q 0 717 IsaQ sauaS \ \\ I I I I//! 1cEN :° No. 58705 -_� _- ®0 F TE S i ®OAL E�� iiII1\\ A. LYNN MILLER, P.E. P.E.# 58705 Overall Width Sash Configuration Width Range (in) Design Pressure (Ibs/ft2) for XOX Windows Glass Types: 1, 4, 5 Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. 1/ 1/ - 4 4- 21/3-1/3-1/3 12.038 - 12.052 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 44" 12.053 - 15.008 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 �4-y2-1/4 12.038 - 13.302 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 49" 1/3-1/3-1/3 13.303 - 16.675 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 1 -60.0 1/4-1/2-1/4 12.038 - 14.333 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 53-1 /8" 1/3_1/3-1/3 14.334 - 18.050 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 " 1/ - 21/ - 4 1/ 4 12.038 - 16.302 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 61 1/3-1/3-1/3 16.303 - 20.675 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 1/4-1/2-1/4 12.038 - 20.052 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +51.9 -51.9 76" custom 20.053 - 22.185 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 1/3_1/3-1/3 22.186 - 25.675 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 %4-1/2-%4 ** - 24.082 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +58.2 -58.2 +53.9 -53.9 +48.7 -48.7 92-1/8" custom 24.083 - 26.185 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +57.8 -57.8 1/3-1/3-1/3 26.186 - 31.038 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 1/4-12-1/4 ** - 25.302 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +58.2 -58.2 +53.9 -53.9 +48.7 -48.7 97" custom 25.303 - 27.185 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +55.5 -55.5 custom 27.186 - 31.038 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +58.6 -58.6 1/4_%2-1/4 ** - 28.302 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +58.2 -58.2 +53.9 -53.9 +48.7 -48.7 109" custom 28.303 - 29.185 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +59.8 -59.8 +51.3 -51.3 custom 29.186 - 31.038 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 +52.5 -52.5 120" %4-12-1/4 ** - 31.038 +60.0 -60.0 +60.0 -60.0 +60.0 -60.0 T +58.2 -58.2 +53.9 -53.9 +48.7 -48.7 `* MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 57.924 2 " MIN. SASH WIDTH (FIN & EQUAL -LEG WINDOWS) = OVERALL WIDTH - 56.924 2 NOTES: 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR INTEGRAL FIN AND EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE 1/8"AN GLASS .090" PVB 1/8" AN GLASS 24 30 1 /2" NOM. GLASS BITE � u u u 74 32 GLASS TYPE 1 13/16" NOM. GLASS STACK AIRSPACE 090" PVB 1 /8" AN GLASS- 1 /8" AN GLASS 3� 74 �OR 1B 1/2" NOM. GLASS BITE EXTERIOR T a 70-73 33AOR 33B GLASS TYPE 4 13/16" NOM. GLASS STACK AIRSPACE 090" PVB 1 /8" TIP 1 /8" AN GLASS�i GLASS 3� ( 74 , u F�GLASS BITE 70-73 *OR 336 GLASS TYPE 5 v co W z Cn w OM a� Q o o W o O a}oa U' CV z Q' O OJ M �� .. Cn Z O _j o acow ZLL o -= _j W r J �8 wU� J J u oaa ON DMO Z F_ � Of in p a o Z Z U W J W J M CA r LL p H O C "' rn ® rn N w N � 7aa4S = O Cn Cn 2 o d o Z Z r- Uj U J W = Q 0 a�711 asaa sauaS �.° 3 N0. 58705 ' PT -O - �1 STE OF F A�� /f ONA.L. 1� \\�o A. LYNN MILLER, P.E. P.E.# 58705 TABLE 8: 1/8" HS GLASS 090" PVB 1/8" HS GLASS 30 24 1/2" NOM. GLASS BITE EXTERIOR a 74 32 GLASS TYPE 2 3/16" AN GLASS 090" PVB 30 3/16" AN GLASS 23 1/2" NOM. GLASS BITE EXTERIOR 1 a 1 74 ;1GLASS TYPE 3 " MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 MIN. SASH WIDTH (FIN & EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 NOTES: 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR INTEGRAL FIN AND EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. Overall Width sash Configuration Sash Range In ��) Glass Types: 2, 3 Design Pressure (Ibs/ft2) for XOX Windows Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. 1/4-1/2_1/4 12.038 - 12.052 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 44" 1/3-1/s-1/s 12.053 - 15.008 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 �a_1/2_1/4 12.038 - 13.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 49" 1/3-1/3-1/3 13.303 - 16.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 �4_1/2_1/a 12.038 - 14.333 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 53-1/8 1/3-1/3-1/3 14.334 - 18.050 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4_1/2_1/4 12.038 - 16.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 61" 1/3-1/3-%3 16.303 - 20.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4_1/2_�a 12.038 - 20.052 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 76" custom 20.053 - 22.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3-1/3-1/3 22.186 - 25.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/a_1/2_ �4 ** - 24.082 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 92-1/8" custom 24.083 - 26.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3-1/3-1/3 26.186 - 31.048 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 �4-1/2-1/4 ** - 25.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 97" custom 25.303 - 27.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3-1/3-1/3 27.186 - 32.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4_1/2_1/4 ** - 28.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 109" custom 28.303 - 30.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3_1/3_1/3 30.186 - 36.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4_1/2_1/4 ** - 29.463 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 113-5/8" custom 29.464 - 33.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3_1/3_1/3 33.186 - 38.222 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 �4_1/2_1/4 ** - 31.052 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 120" custom 31.053 - 33.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 custom 33.186 - 38.222 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 Approved as Complying with f Fl de Bra ' g ad Date - - 0 O W Z > O U) � nab vi w � OO F LLI O } ti o > U' CVO O Q' a}oQ z � M F w J � (n Z C7 J O a cn ZLL (D CO = � J Z W O ti W r N �8 W ( o J ¢ J umoa0 ON I' W _9 H SM a > o � a U) Z Z O O IY W W J O < O rn W ® rn N 0 aayS U)04 G7 Q � � Q � O a o w Z_ � Z � ' U J W = Q o of}il asaQ saiaaS vv`v `l LYN/V i OCEN _ No.58705 0 '. SATE OF //Slilllll� ONAL A. LYNN MILLER, P.E. P.E.# 58705 Overall Width Sash Configuration Width In Range 9 (in) Meeting Rail: Standard Design Pressure (Ibs/ft2) Glass Types: 6, 7 for XOX Windows 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. 1/4_1/2_1/4 12.038 - 12.052 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 44" 1/ - 31/ - 3 1/ 3 12.053 - 15.008 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4_1/2-1/4 12.038 - 13.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 49" 1/3-103-1/3 13.303 - 16.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4-%-1/4 12.038 - 14.333 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 53-1 /8" 1/3-1/3_1/3 14.334 - 18.050 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4-1/2-1/4 12.038 - 16.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 61" 1/3_1/3-1/3 16.303 - 20.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4-y2-1/4 12.038 - 20.052 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -72.9B 76" custom 20.053 - 22.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3-1/3-1/3 22.186 - 25.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4-1/2-y4 ** - 24.082 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -74.1A +65.0 -67.513 92-1/8" custom 24.083 - 26.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/3_1/3-1/3 26.186 - 31.048 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4-12 _ y4 ** - 25.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -74.1 A +65.0 -67.513 97" custom 25.303 - 27.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -77.9 1/3_1/3_1/3 27.186 - 32.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 1/4-12-1/4 -- - 28.302 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -74.1A +65.0 -67.513 1091, custom 28.303 - 30.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -72.0 1/3_1/3-1/3 30.186 - 36.675 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -75.8 1/4-1/2-y4 *- - 29.463 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -74.1A +65.0 -67.513 113-5/8" custom 29.464 - 33.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -70.6 1/3_1/3-1/3 33.186 - 38.222 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -76.9 1/4-1/2-1/4 ** - 31.052 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -74.1A +65.0 -67.513 120" custom 31.053 - 33.185 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -75.7 +65.0 -68.4 custom 33.186 - 38.222 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -80.0 +65.0 -71.3 " MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 * MIN. SASH WIDTH (FIN & EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 NOTES: 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR INTEGRAL FIN AND EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. --bU.0 rUK UL/HJJ I Tr'L s-75.0 FOR GLASS TYPE 7 13/16" NOM. GLASS STACK AIRSPACE .090" PVB 3/16" AN OR TP GLASS I ( � 1/8" AN GLASS 31 74 1A OR' �lB 1/2" NOM. GLASS BITE 70-73 33 OR 33B GLASS TYPE 6 (ANNEALED) GLASS TYPE 7 (TEMPERED) 00 W ? OM (n nab W �o O o U' N > z O a}oQ � O M Lu 07 O z J LL O (D CL �° W O z = LL N g aMDJO U 0 Jj W J ~ c_7 ¢ H aN SM 0 W >� �a Z Op Z o U Of W W J M LL J O O W ® rn N _ 04 O 07 TOayS D = W Q O� Q LL = EL O w Z_ Z ' U _I W = Q 0 Ona ' Gq sauaS `�yaliil!!I///1 e \-ICENSc No.58705 O S ATE OF o: Syr) A. LYNN MILLER, P.E. P.E.# 58705 TABLE 10 3/16" AN GLASS .090" SG 3/16" AN GLASS 30 23 1/2" NOM. GLASS BITE EXTERIOR 74 32 GLASS TYPE 8 GLASS STACK AIRSPACE 090" SG 1 /8" AN OR TP GLASS 3/16" AN GLASS 74 1AOR1/2"NOM. fOGLASSBITIE EXT70-73 33A OR GLASS TYPE 10 (ANNEALED) GLASS TYPE 11 (TEMPERED)` GLASS TYPES 8 - 15 MAY NOT BE USED WITH INTEGRAL FIN • FRAMES MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 ** MIN. SASH WIDTH (EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 NOTES: 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. Overall Width Sash Configuration Sash Range In (�) Glass Types: 8, 10, 11 Design Pressure (Ibs/ft2) for XOX Windows Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. 1/4_1/2_1�4 12.038 - 12.052 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 44" 1/ 1/ 1/ 3- 3- 3 12.053 - 15.008 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4_1�2_1�4 12.038 - 13.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 49" 1/3-1/3-1/3 13.303 - 16.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 12.038 - 14.333 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 53-1 /8 1/3-1/3-1/3 14.334 - 18.050 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1�a_1�2_�a 12.038 - 16.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 61" 1/3-1/3-1/3 16.303 - 20.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4_1� _1/4 12.038 - 20.052 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -99.2 76" custom 20.053 - 22.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/3_1/3_1/3 22.186 - 25.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1�4_1�2_1�4 ** - 24.082 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -101.0 +80.0 -90.5 92-1/8" custom 24.083 - 26.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -105.2 1/3-1/3-1/3 26.186 - 31.048 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -102.3 1�4-1�2-1�4 ** - 25.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -101.0 +80.0 -90.5 97" custom 25.303 - 27.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -102.7 1/3-1/3-1/3 27.186 - 32.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -98.9 1/4_1�2_1�4 ** - 28.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -101.0 +80.0 -90.5 109" custom 28.303 - 30.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -97.3 1/3-1/3-1/3 30.186 - 36.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -92.9 1/4_1/2_1�4 ** - 29.463 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -101.0 +80.0 -90.5 113-5/8" custom 29.464 - 33.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -108.5 +80.0 -94.1 1/3-1/3-1/3 33.186 - 38.222 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -92.3 1�4_ �2_ �a ** - 31.052 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -101.0 +80.0 -90.5 120" custom 31.053 - 33.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -102.9 +80.0 -91.5 custom 33.186 - 38.222 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -90.6 � 00 Y Lu ? � (n > N O (� > nab Of 0 w � 0 00 0 O LO > U' N Do > z O ' aToa � O M LS cn O Z _J O d cn W O Z �- 00= _ � � = LLB r N � J �� WU� aJ _j u�ao aN W SMa > p _2 U) Z z 0 O U Of W W J D7 -' < O W °° ® N) N N = O U) aa4S � = 07 Lu Q Q o a o � Z Z C0 , LLI U J W = Q a�Til �asa� sauaS QA,Y LYNA/ _\CENS No.53705 �� 775 -' %�l °•��ORIDR.•°°'ate A. LYNN MILLER, P.E. P.E.# 58705 ✓�� Overall Width Sash Configuration Sash Wilt Range (in) Meeting Rail: Standard Design Pressure (Ibs/ft2) Glass Types: 9, 12, 13, 14, 15 for XOX Windows 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt.T6F Overall Hgt. 1/4-1/2-1/4 12.038 - 12.052 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 44" 1/3-1/3-1/3 12.053 - 15.008 +80.0 -1 %0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 �4-1/2-1/4 12.038 - 13.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 49" 1/3-1/3-1/3 13.303 - 16.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-%-% 12.038 - 14.333 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +8&0 -110.0 +80.0 -110.0 +80.0 -110.0 53-1 /8" 1/3-1/3-1/3 14.334 - 18.050 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 ,/-�-1/4 12.038 - 16.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 61" LY3-1/3-1/3 16.303 - 20.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-1/2-1/4 12.038 - 20.052 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 76" custom 20.053 - 22.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/3-1/3-1/3 22.186 - 25.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-1/2- �4 ** - 24.082 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -106.7* 92-1/8" custom 24.083 - 26.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/3-1/3-1/3 26.186 - 31.048 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-y2-y4 ** - 25.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -106.7* 97" custom 25.303 - 27.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/3-1/3-1/3 27.186 - 32.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-1/2-1/4 ** - 28.302 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -106.7* 109" custom 28.303 - 30.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/3-1/3-1/3 30.186 - 36.675 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-1/2-1/4 ** - 29.463 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -106.7* 113-5/8" custom 29.464 - 33.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/3-1/3-1/3 33.186 - 38.222 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 1/4-1/2-1/4 ** - 31.052 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -106.7* 120" custom 31.053 - 33.185 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -107.8 custom 33.186 - 38.222 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 +80.0 -110.0 "* MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 MIN. SASH WIDTH (EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. -I I U.0 Fll V LP\JJ I l r LJ J, I , I J lJt I J 'GLASS TYPES 8 - 15 MAY NOT BE USED WITH INTEGRAL FIN • FRAMES 3/16" HS GLASS .090" SG 30 3/16" HS GLASS 23 n1/2" NOM. GLASS BITE 74 32 GLASS TYPE 9 13/16" NOM. GLASS STACK AIRSPACE 090" SG 1 /8" AN OR TP GLASS -� 1 /8" HS GLASS 31 74 1AOR 1B 1pr /2" NOM. GLASS BITE � u 70-73 33A OR 33B GLASS TYPE 12 (ANNEALED) GLASS TYPE 13 (TEMPERED) If. 13/16" NOM. I GLASS STACK AIRSPACE .090" SG 3/16" AN OR TP GLASS 1/8" HS GLASS ,, 3� 74 1A OR 113 1/2" NOM. GLASS BITE EXTERIOR 70-73 33A OR 33B GLASS TYPE 14 (ANNEALED) GLASS TYPE 15 (TEMPERED) % �_ w Z i o cn nab W CM C° O o UJ o cn N i O 0 ' Q a7aQ UI CV z w O W 0Oz cc J O �U) W O Z °p= = u � ►� C) 00 LULI J ¢ J unno�� O W 9 F- OM Z CL z rn O - U Of w J w J m LL JO O `° rn cr_ F w rn ® rn N N = O U) 77 D = w 0 d O O Z_ Z 0 w ' v i w = Q a17iiasa� sauaS �� •• `• LICENSE °•. ��f� J II No.58705 ATE ®M S A. LYNN MILLER, P.E. P.E.# 58705 W11.19MM Glass Types: 1 thru 7 Anchor Quantities for XO & OX Windows Meeting Rail: Standard Overall Width 22.1/8" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. Head & Sill E Head & Sill E Head & Sill Head & Sill E Head & Sill E co 20" 1+C2+1 21 1+C2+1 21 1+C2+1 31 1+C2+1 31 1+C2+1 3 25" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C2+1 3 37" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C2+1 3 49" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C2+1 3 61" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C2+1 3 67" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C3+1* 3 74" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C3+1 * 3 '1+C2+1 FOR GLASS I YHE6 1, 4 & 5 TABLE 13 Glass Types: 8 thru 15 Anchor Quantities for XO & OX Windows Meeting Rail: Standard Overall Width 22-1/8 Overall Hgt. 37 Overall Hgt. 49 Overall Hgt. 55 Overall Hgt. 63 Overall Hgt. Head & Sill E Head & Sill E Head & Sill E Head & Sill E Head & Sill 20" 1+C2+1 2 1+C2+1 21 1+C2+1 3 1+C2+1 3 1+C2+1 3 25" 1+C2+1 2 1+C2+1 21 1+C2+1 3 1+C2+1 3 1+C2+1 3 37" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C2+1 3 49" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C3+1 3 61" 1+C2+1 2 1+C2+1 2 1+C2+1 31 1+C3+1 3 1+C3+1 3 67" 1+C2+1 2 2+C2+2 2 2+C2+2 3 2+C3+2 3 2+C3+2 3 74" 2+C2+2 2 2+C2+2 2 2+C2+2 3 2+C3+2 3 2+C3+2 4 TABLE 14: GUIDE TO USING ANCHOR QUANTITY TABLES FOR XO/OX WINDOWS: CLUSTER OF 3 2ANCHORS ANCHORS AT THE CENTERED AT THE SASH MEETING RAIL 12" MAX. O.C. Glass Types: 8 thru 15 Anchor Quantities for XO & OX Windows Meeting Rail: Heavy -Duty Overall Width 22-1/8" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. 76" Overall Hgt. Head & Sill E Head & Sill Head & Sill E Head & Sill E Head & Sill E Head & Sill E cEa 20" 1+C2+1 21 1+C2+1 21 1+C2+1 31 1+C2+1 3 1+C2+1 31 1+C2+1 4 25" 1+C2+1 2 1+C2+1 2 1+C2+1 31 1+C2+1 3 1+C2+1 31 1+C2+1 4 37" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C2+1 3 1+C3+1 4 49" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C2+1 3 1+C3+1 31 1+C3+1 4 61" 1+C2+1 2 1+C2+1 2 1+C2+1 3 1+C3+1 3 1+C3+1 3 1+C4+1 4 67" 1+C2+1 2 2+C2+2 2 2+C2+2 3 2+C3+2 3 2+C3+2 3 2+C4+2 4 76" 2+C2+2 2 2+C2+2 2 2+C3+2 3 2+C3+2 3 2+C3+2 4 2+C4+2 5 2 ANCHORS AT I4 ANCHORS IN THE THE FIXED LITE JAMB 23" MAX. O.C. —� 9" MAX. 1 9" MAX. 1 / X O / 22-1/2" MAX. O.C. MEETING RAIL REPEAT ANCHOR PATTERN AT SILL 2-ANCHOR CLUSTER DETAIL 4" MAX. O.C. 6" MAX. O.C.(�— I 3-ANCHOR CLUSTER DETAIL 4-ANCHOR CLUSTER DETAIL NOTES- 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. W z (n > wOf O M naa Q � Q O U) > O a}oQ (D N z W W U) O M Z Z p J o av) u- W z m `°_ _ WN 0 W U ¢ J UMOJQ aN W 0 SMO > rn 'qj- o Z rn o z W J J CO rn LL O O 0 ® rn N H ZQ aayS O Z _ a 0 Q O I-- Z O _ LU Q Q a1}il asaQ sauaS `\t�`IIIIt}f�r�J` �®�AY LY�IV �1 CEN&F No.58705 � ® is ATE 1 44j 0/0 A. LYNN MILLER, P.E. P.E.# 58705 TABLE 15 Overall Width Sash Configuration Sash Width Range (in) Glass Types: 1, 4, 5 Anchor Quantities for XOX Windows Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. Head &Sill m Head & Sill Head &Sill -0 Head &Sill Head &Sill Head &Sill -0 �/4-1�2-Y4 12.038 - 12.052 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 44" 1�3-1�3-1�3 12.053 - 15.008 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4_1/2_1/4 12.038 - 13.302 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 49" 1/3-1/3_1/3 13.303 - 16.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4_1/2 1/4 12.038 - 14.333 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 53-1/8" 1�3-1�3 1�3 14,334 - 18.050 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�4-1�2-1�4 12.038 - 16.302 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 61" 1�3 1�3-1�3 16.303 - 20.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4-1/2-1/4 12.038 - 20.052 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C2+2+C2+1 3 76" custom 20.053 - 22.185 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�3-1�3-1�3 22.186 - 25.675 1+C2+1+C2+1 2 1+C2+1+C2+1 21 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�4-1�2-1/4 ** - 24.082 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C2+3+C2+1 3 92-1/8" custom 24.083 - 26.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1/3-1�3 1�3 26,186 - 31,038 1+C2+1+C2+1 21 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4-1/2-1/4 * - 25.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C2+3+C2+1 3 97" custom 25.303 - 27.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C2+2+C2+1 3 custom 27,186 - 31.038 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 31 1+C2+2+C2+1 3 1�4-1�2-Y4 "" - 28.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C2+3+C2+1 3 109" custom 28.303 - 29.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C2+3+C2+1 3 custom 29.186 - 31.038 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C2+3+C2+1 3 120" 1/4-1�2-1/4 *" -31.038 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 1 3 1+C2+3+C2+1 3 1+C2+3+C2+1 3 *' MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 57.924 2 MIN. SASH WIDTH (EQUAL -LEG WINDOWS) = OVERALL WIDTH - 56.924 2 NOTES- 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. GUIDE TO USING ANCHOR QUANTITY TABLES FOR XOX WINDOWS: 12" MAX. O.C. -I 2-ANCHOR CLUSTER DETAIL CLUSTER OF 2 CLUSTER OF 2 3 ANCHORS ANCHORS ANCHORS IN THE 1 ANCHOR AT CENTERED AT THE CENTERED AT THE THE SASH 3 ANCHORS AT MEETING RAIL JAMB MEETING RAIL I �THEFIXEDLITE 22-1/2" MAX. O.C. 1 ANCHOR AT 9" MAX. i 12" MAX. O.C. THE SASH i - - 9" MAX. X MEETING RAIL REPEAT ANCHOR PATTERN AT SILL U O ;;7 LU ? � (n Aaa w (D O o �w > > o O Q a71 O M W w W U) O J O J O C7 � IL cn .-. Z W Z O ZLL cop `°_ LLi U� r N � J u�aa W Z o f J ON OMO O � � a (n Z O Z O J W m O LL O F¢- O rn i ® rn N H N = O F_ Z Q ways C) Q o Cr z O LLJ v U J Z = awl .a¢O sauas 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. A. LYNN MILLER, P.E. P. E.# 58705 TAB[ F 16 Overall Width Sash Configuration Sash Width Range (in) Glass Types: 2, 3, 6, 7 Anchor Quantities for XOX Windows Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. f 49" Overall Hgt. 55" Overall Hgt. 63" Overall Hgt. Head & Sill .0 E Head & Sill E Head &Sill E Head & Sill E co Head & Sill Q E Head &Sill -0 E 1�4-1�2-1�4 12.038 - 12.052 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 44" 1�3-Y3 1/3 12.053 - 15.008 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 �4-1�2-1�4 12.038 - 13.302 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 49" 1/3-1/3-1/3 13.303 - 16.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�4-1�2-Y4 12.038 - 14.333 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 53-1/8" 1�3-1�3-Y3 14.334 - 18.050 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�4-1�2-Y4 12.038 - 16.302 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 61" Y3 1/3 %3 16.303 - 20.675 1+C2+1+C2+1 21 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�4-1�2-1�4 12.038 - 20.052 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C2+2+C2+1 3 76" custom 20.053 - 22.185 1+C2+1+C2+1 2 1+C2+1+C2+1 21 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1�3-1�3-1�3 22.186 - 25.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4-1�2-1/4 ** - 24.082 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 92-1/8" custom 24.083 - 26.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1�3 1�3-1�3 26,186 - 31.048 1+C2+1+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1�4'1�2-1�4 *- - 25.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 97" custom 25.303 - 27.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 21 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1/3-1/3-1/3 27.186 - 32.675 1+C2+1+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1/4-1/2_1/4 ** - 28.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1091, custom 28.303 - 30.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1/3-1/3-1/3 30.186 - 36.675 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 Y4-1/2-y4 ** - 29.463 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 113-5/8" custom 29.464 - 33.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 31 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1�3-1�3-1�3 33.186 - 38.222 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1/4-1/2_1/4 ** - 31.052 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 120" custom 31.053 - 33.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 custom 33.186 - 38.222 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+3+C2+1 3 1+C3+3+C3+1 3 MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 " MIN. SASH WIDTH (EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 12" MAX. O.C. 1 2-ANCHOR CLUSTER DETAIL 6" MAX. O.C. 3-ANCHOR CLUSTER DETAIL GUIDE TO USING ANCHOR QUANTITY TABLES FOR XOX WINDOWS: CLUSTER OF 2 ANCHORS 1 ANCHOR AT CENTERED AT THE THE SASH MEETING RAIL CLUSTER OF 2 ANCHORS CENTERED AT THE 3 ANCHORS IN THE JAMB 3 ANCHORS AT MEETING RAIL THE FIXED LITE 22-1/2" MAX. O.C. ►- 9" MAX. 12" MAX. O.C. --0 ----� r----�---- r- NOTES: -J L_-- -_j - 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG / X / O X WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE / TO DETERMINE THE WINDOW SIZE. 1 ANCHOR AT THE SASH 9" MAX. MEETING RAIL REPEAT ANCHOR PATTERN AT SILL 00 W ? c>n 0 o M > AaIli 0 o O 0 1 o O Q a}oQ U` C\1 z C O M w (q O F J CD � ^ Z Z O J O av> LL W O Z co - = v __3 LV N 6 o -ji 4[E umoic] w 00 J a _j ~o WNT 9 F- 9Ma >� Of U) 0 a Z Z J W M rn LL O N rn ® rn N N Of F- ZQ aayS = O D _ Q O Q LL z p � 2 Uj ::) U J Z 2 Q Q a�}!1 �asaQ saua5 t GAS LYIV/V's�,. �� .•'��CEN � • 1l '� No. 58705 _ >Q STATE OF f(7441� /11111110 \\\ 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. A. LYNN MILLER, P.E. P.E.# 58705 TABLE 17: Overall Width Sash Configuration Sash Width Range (in) Glass Types: 8, 10, 11 Anchor Quantities for XOX Windows Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 55" Overall Hgt. 1 63" Overall Hgt. Head &Sill Head &Sill -Q -� Head & Sill -0 E Head & Sill . m Head & Sill E -) Head &Sill •Q -� 44" �4-1/2-1/4 12.038 - 12.052 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/3-1/3-1/3 12.053 - 15.008 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 Y4-1/2-1/4 12.038 - 13.302 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 49" 1/3-1/3-1/3 13.303 - 16.675 1+C2+1+C2+1 21 1+C2+1+C2+1 21 1+C2+1+C2+1 2 1+C2+1+C2+1 31 1+C2+1+C2+1 3 1 1+C2+1+C2+1 3 1/4-1/_1/4 12.038 - 14.333 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 53-1 /8" 1/3-1/3-1/3 14.334 - 18.050 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4_1/2_1/4 12.038 - 16.302 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 61" 1/3-1/3-1/3 16.303 - 20.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C3+1+C3+1 3 1/4-1/2_Y4 12.038 - 20.052 1+C2+2+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1+C3+3+C3+1 3 76" custom 20.053 - 22.185 1+C2+1+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/3-1/3-1/3 22.186 - 25.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C3+1+C3+1 3 1+C3+1+C3+1 3 1/4-12_Y4 ** - 24.082 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+3+C3+1 3 92-1/8" custom 24.083 - 26.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/3-1/3-1/3 26.186 - 31.048 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/4-%2-1/4 ** - 25.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+3+C3+1 3 97" custom 25.303-27,185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1+C3+2+C3+1 3 1/3-1/3-1/3 27.186 - 32.675 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 Y4-1/2-1/4 ** - 28.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+3+C3+1 3 1091, custom 28,303 - 30.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1+C3+3+C3+1 3 1/3-1/3-1/3 30.186 - 36.675 1+C2+2+C2+1 2 2+C2+2+C2+2 2 2+C2+3+C2+2 2 2+C3+3+C3+2 3 2+C3+3+C3+2 3 1+C3+2+C3+1 3 1/4-1/2- �4 *" - 29.463 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+3+C3+1 3 113-5/8" custom 29.464 - 33.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C3+3+C3+1 3 1+C3+3+C3+1 3 1+C3+3+C3+1 3 1/3-1/3-1/3 33.186 - 38.222 2+C2+2+C2+2 2 2+C2+2+C2+2 2 2+C2+3+C2+2 2 2+C3+3+C3+2 3 2+C3+3+C3+2 3 2+C3+2+C3+2 3 1/4_1/2-1/4 ** - 31.052 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+3+C3+1 3 120" custom 31.053 - 33.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 1 21 1+C3+4+C3+1 3 1+C3+4+C3+1 3 1+C3+3+C3+1 3 custom 33.186 - 38.222 2+C2+2+C2+2 2 2+C2+3+C2+2 2 2+C2+3+C2+2 1 21 2+C3+3+C3+2 3 2+C3+3+C3+2 3 2+C3+3+C3+2 1 3 - MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 - MIN. SASH WIDTH (EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 12" MAX. O.C. 2-ANCHOR CLUSTER DETAIL 6" MAX. O.C. - 3-ANCHOR CLUSTER DETAIL GUIDE TO USING ANCHOR QUANTITY TABLES FOR XOX WINDOWS: CLUSTER OF 2 CLUSTER OF 2 3 ANCHORS ANCHORS ANCHORS IN THE 1 ANCHOR AT CENTERED AT THE CENTERED AT THE THE SASH MEETING RAIL 3 ANCHORS AT MEETING RAIL JAMB THE FIXED LITE 22-1/2" MAX. O.C. j 1 ANCHOR AT 9" MAX 12" MAX. O.C. THE SASH NOTES: - ----J �_- - - 9" MAX. 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG / X / O X WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE TO DETERMINE THE WINDOW SIZE. MEETING RAIL REPEAT ANCHOR PATTERN AT SILL b 00Y W z n (> � O M > naZ 0 Now CDO } o > O Q a}o0 U N z� O w (n O J cc 0 Z Z O _I LL' O av> `° W O Z W (0 3:= N E [` �g umoiC7 wU 0 o f .I Z `r = Q 3M a > a U) Z O W J W CO W O rn O } M ® rn N N F- ZQ aays = O D _ Q CJ Q o z O � 2 Uj U � JU Z = Q Q a�}�l 'asaQ sauas \`ty1VtEr1i/P��i O�V LYN/V a i No.58705 ' %-)3O ATE OF �v 'ONAL 00 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. A. LYNN MILLER, P.E. P.E.# 58705 TARI G 1R Overall Width Sash Configuration Sash Width Range (in) Glass Types: 9, 12, 13, 14, 15 Anchor Quantities for XOX Windows Meeting Rail: Standard 21-1/8" Overall Hgt. 29" Overall Hgt. 37" Overall Hgt. 49" Overall Hgt. 1 55" Overall Hgt. 63" Overall Hgt. Head &Sill - Head &Sill Head & Sill s Head &Sill Head &Sill .0 Head &Sill -0 1/4-1/2-1/4 12.038 - 12.052 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 44" 1/3-1/3-1/3 12.053 - 15.008 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4-1/2-1/4 12.038 - 13.302 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 49" 1/3-1/3-1/3 13.303 - 16.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4-1/2-1/4 12.038 - 14.333 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 53-1 /8" 1/3-1/3-1/3 14.334 - 18.050 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1+C2+1+C2+1 3 1/4-1/2-1/4 12.038 - 16.302 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C2+2+C2+1 3 1+C3+2+C3+1 3 61" 1/3-1/3-1/3 16.303 - 20.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 11+C2+1+C2+1 3 1+C3+1+C3+1 3 1/4-1/2-1/4 12.038 - 20.052 1+C2+2+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1+C3+3+C3+1 3 76" custom 20.053 - 22.185 1+C2+1+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/3-1/3-1/3 22.186 - 25.675 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 2 1+C2+1+C2+1 3 1+C3+1+C3+1 3 1+C3+1+C3+1 3 1/4-1/2-1/4 ** - 24.082 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+4+C3+1 3 92-1/8" custom 24.083 - 26.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/3-1/3-1/3 26.186 - 31.048 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/4-1/2-Y4 ** - 25.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+4+C3+1 3 97" custom 25.303 - 27.185 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1+C3+3+C3+1 3 1/3-1/3-1/3 27.186 - 32.675 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 2 1+C2+2+C2+1 3 1+C3+2+C3+1 3 1+C3+2+C3+1 3 1/4 -1/2 -1/4 -28.302 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C3+4+C3+1 3 109" custom 28.303 - 30.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 3 1+C3+3+C3+1 3 1+C4+3+C4+1 3 1/3-1/3-1/3 30.186 - 36.675 1+C2+2+C2+1 2 2+C2+2+C2+2 2 2+C2+3+C2+2 2 2+C3+3+C3+2 3 2+C3+3+C3+2 3 2+C4+3+C4+2 4 1/4-1/2_Y4 *- - 29.463 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C4+4+C4+1 3 113-5/8" custom 29.464 - 33.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C3+3+C3+1 3 1+C3+3+C3+1 3 1+C4+3+C4+1 3 1/3-1/3-1/3 33.186 - 38.222 2+C2+2+C2+2 2 2+C2+2+C2+2 2 2+C2+3+C2+2 2 2+C3+3+C3+2 3 2+C3+3+C3+2 3 2+C4+3+C4+2 4 1/4-1/-1/4 -- - 31.052 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+4+C2+1 3 1+C3+4+C3+1 3 1+C4+4+C4+1 3 120" custom 31.053 - 33.185 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C2+3+C2+1 2 1+C3+4+C3+1 3 1+C3+4+C3+1 3 1+C4+4+C4+1 3 custom 33.186 38.222 2+C2+2+C2+2 2 2+C2+3+C2+2 2 2+C2+3+C2+2 2 2+C3+3+C3+2 3 2+C3+3+C3+2 31 2+C4+3+C4+2 4 '* MIN. SASH WIDTH (FLANGE WINDOWS) = OVERALL WIDTH - 58.556 2 `* MIN. SASH WIDTH (EQUAL -LEG WINDOWS) = OVERALL WIDTH - 57.556 2 GUIDE TO USING ANCHOR QUANTITY TABLES FOR XOX WI N nn1/VS ` 12" MAX. O.C. 6" MAX. O.C. 9-ANCHnR CLUSTER DETAIL 3-ANCHOR CLUSTER DETAIL 4" MAX. O.C. -I 4-ANCHOR CLUSTER DETAIL I1 +'C21+3+C2+1 �113 i CLUSTER OF 2 CLUSTER OF 2 3 ANCHORS ANCHORS ANCHORS IN THE 1 ANCHOR AT CENTERED AT THE 3 ANCHORS AT CENTERED AT THE JAMB THE SASH MEETING RAIL MEETING RAIL -_ THE FIXED LITE 22-1/2" MAX. O.C. 1 ANCHOR AT 9" MAX. 12" MAX. O.C. THE SASH i NOTES: --� ---- ----� In rn 1 I 1) OVERALL (TIP TO TIP) DIMENSIONS SHOWN. FOR EQUAL -LEG J 9 MAX. WINDOWS, SUBTRACT 1" FROM THE TIP -TO -TIP DIMENSION IN THE TABLE X / O X TO DETERMINE THE WINDOW SIZE. MEETING RAIL-/ REPEAT ANCHOR PATTERN AT SILL � 00 Y LU i ? � OM (n a� w �o m O O (n � (D N 0 � Z w O Q a}o0 O � M w (n O Z 0 J O a U)LL �_ Z WO z = LL coo ti UM DJQ F_ WU Z NT -j = QCo _j �Ma o > Of U) z z °' o W rn LU J m LL O M O F ® rn N H O F- Z }aayS Q c C) Q o Q Z O ti U J z 2 Q Q aµ�1 asap sauaS i \� LICENSE _ No.58705 SATE OF �e '4ORID�° N°�� i� /OfVAL ��1lIII11°� 2) FOR SIZES NOT SHOWN, ROUND UP TO THE NEXT AVAILABLE SIZE. A. LYNN MILLER, P.E. P.E.# 58705 INSTALLATION OPTION 1 ANCHORED THROUGH FRAME INTO 2X WOOD FRAME OR BUCKSTRIP. SEE NOTE 2, THIS SHEET. EDGE DISTANCE 1/4" MAX. SHIM OVERALL HEIGHT 1/4" MAX. SHIM EXTERIOR a _ EDGE — f DISTANCE �1 INSTALLATION OPTION INSTALLATION OPTION 2 ANCHORED THROUGH FRAME DIRECTLY INTO CONCRETE/CMU. 1/4" MAX. SHIM EMBEDMENT SEE TABLE T NOTE B, FOR .1( HEAD TYPE EDGE ° ° ° ° EMBEDMENT DISTANCE G TYP. ANCHOR TYPE, a ° EMBEDMENT AND EDGE e DISTANCE PER SUBSTRATE, SEE TABLE 19. I SASH VISIBLE LIGHT WIDTH 12" LENGTH, CENTERED J III �J EXTERIOR ABOVE SASH ° ' °' ° 16 14 15 TYP. ANCHOR TYPE, EMBEDMENT AND EDGE OVERALL WIDTH DISTANCE PER SUBSTRATE, SEE TABLE 19 HORIZONTAL SECTION A -A & NOTE B FOR HEAD TYPE. (SHOWN WITH I.G. GLAZING) VISIBLE LIGHT HEIGHT 6"LENGTH,CENTERED AT MEETING RAIL, ANCHORED WITH (4) SCREWS, (P# 60). ONLY REQUIRED IF OVERALL HEIGHT IS OVER 63". EMBEDMENT TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE 2 SEE TABLE 19. ANCHORED THROUGH FRAME DIRECTLY INTO CONCRETE/CMU. VERTICAL SECTION B-B NOTES INSTALLATION OPTION 3 ANCHORED THROUGH FRAME AND 1X BUCKSTRIP INTO CONCRETE/CMU. SEE NOTE 2, THIS SHEET. 1/4" MAX. SHIM EMBEDMENT 4 EDGE 177TI ° 8 DISTANCE FIXED VISIBLE LIGHT WIDTH EXTERIOR MIAMI-DADE APPROVED MULLION, FBC COMPLIANT ALUMINUM/STEEL FRAMING OR STEEL STUD. MAY BE VERTICAL OR HORIZONTAL SECTION C-C HORIZONTAL. SEE SUBSTRATE (SHOWN WITH MONO. GLAZING) PROPERTIES, TABLE 19. 1) USE ONLY SUBSTRATE -APPROPRIATE ANCHORS LISTED ON TABLE 19. FOLLOW EMBEDMENT AND EDGE DISTANCE LIMITS. ANY INSTALLATION OPTION SHOWN MAY BE USED ON ANY SIDE OF THE WINDOW. 2) MASONRY ANCHORS MAY BE USED INTO WOOD AS PER TABLE 19. ALL WOOD BUCKS LESS THAN 1-1/2" THICK ARE TO BE CONSIDERED 1X INSTALLATIONS. 1X WOOD BUCKS ARE OPTIONAL IF UNIT IS INSTALLED DIRECTLY TO SUBSTRATE. WOOD BUCKS DEPICTED AS 2X ARE 1-1/2" THICK OR GREATER. 1X AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED TO PROPERLY TRANSFER LOADS TO THE STRUCTURE. WOOD BUCK DESIGN AND INSTALLATION IS THE RESPONSIBILITY OF THE ENGINEER OR ARCHITECT OF RECORD. 3) VISIBLE LIGHT WIDTH OR HEIGHT (ALSO REFERRED TO AS DAYLIGHT OPENING) IS MEASURED FROM BEADING TO BEADING. TARI_F 19 TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 19 & NOTE B FOR HEAD TYPE. Min. Edge Min. Anchor Substrate Distance I Embedment Southern Pine (SG=0.55) 9/16" 1-3/8" Steel, 18-8 410 8- Aluminum, 6063-T5 min. 3/8" 0.063" or SS Screw A36 Steel 3/8" 0.063" Steel Stud, Gr. 33 min. 3/8" 0.045" (18 Ga) Concrete (min. 3.35 ksi) 1" 1-3/4" 1/4" 410 SS CreteFlex Ungrouted CMU, (ASTM C-90) 2-1/2" 1-1/4" Southern Pine (SG=0.55) V 1-3/8" Steel Concrete (min. 2.85 ksi) V 1-3/8" 1/4" Ultracon Ungrouted CMU, (ASTM C-90) 2-1/2" 1-1/4" Southern Pine (SG=0.55) 1" 1-3/8" 1/4" MAX. SHIM INSTALLATION OPTION 4 ANCHORED THROUGH FRAME INTO METAL TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 19. A) MIN. OF 3 THREADS BEYOND THE METAL SUBSTRATE. B) USE ONLY FLATHEAD ANCHORS IN HEAD AND SILL. PAN/HEX/FLAT HEAD TYPE IS ALLOWABLE FOR ANCHORS IN THE JAMBS. C) "UNGROUTED CMU" VALUES MAY BE USED FOR GROUTED CMU APPLICATIONS. Approved as complymg w1th t r, Flo td_ 'Al Co tt ��3A# y ". "A QW116 vltm! Dade Pimduct CoiArd N ci00Y W ? iU CD M > naZ 0 o cm O O (n i 0 N D > zL O a}oQ O M cn O Z 0 J O CL� _ W z LL (0 OD — = I N F, J 48 wU z 0 J Q J UMDJQ ON �_ C7 � 9M Q 0LLI o> 0 a U) z O Z L) o W —I W O CO co ZZ r- rn ® rn N -J `\ LL aayS = O z � 2 O ¢O LLQ O z J r U _ J Q z a}ail �asa0 saua5 \�,ltllltl/�� 0. /V � s \ . ' \,\GENSF _ No. 58705 O S ATE �\ o T •° • 'ONAL\ A. LYNN MILLER, P.E. P.E.# 58705 INSTALLATION OPTION 1 ANCHORED THROUGH FRAME INTO 2X WOOD FRAME OR BUCKSTRIP. SEE NOTE 2, THIS SHEET. 1/4" MAX. SHIM INSTALLATION OPTION 2 ANCHORED THROUGH FRAME DIRECTLY INTO CONCRETE/CMU, 1/4" MAX. SHIM EDGE DISTANCE I EMBEDMENT Lr ISIBLE LIGHT VWIDTH EMBEDMENT EDGE DISTANCE ° d TYP. ANCHOR TYPE, EMBEDMENT AND EDGE a e DISTANCE PER SUBSTRATE, SEE TABLE 20. 63 EXTERIOR 12" LENGTH, CENTERED M 20 ABOVE SASH ° ° °�, a 16 'J 1 TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 20 & NOTE B FOR HEAD TYPE. VISIBLE LIGHT BUCK HEIGHT 6 HEIGHT 52 50 1/4" MAX. ° d ° SHIM 4 ° EXTERIOR I� EDGE DISTANCE INSTALLATION OPTION 2 6" LENGTH, CENTERED AT MEETING RAIL, ANCHORED WITH (4) SCREWS (P# 60). ONLY el 14 5 BUCK WIDTH INSTALLATION OPTION 3 ANCHORED THROUGH FRAME AND 1X BUCKSTRIP INTO CONCRETE/CMU. SEE NOTE 2, THIS SHEET. I� FIXED VISIBLE LIGHT WIDTH HORIZONTAL SECTION A -A (SHOWN WITH I.G. GLAZING) LIB EXTERIOR i '51 HORIZONTAL SECTION C-C (SHOWN WITH MONO. GLAZING) v REQUIRED IF BUCK NOTES: HEIGHT IS OVER 62". 1) USE ONLY SUBSTRATE -APPROPRIATE ANCHORS LISTED ON TABLE 20. FOLLOW EMBEDMENT AND EDGE DISTANCE LIMITS. ANY INSTALLATION OPTION SHOWN MAY BE USED ON ANY SIDE OF THE WINDOW. d 2) MASONRY ANCHORS MAY BE USED INTO WOOD AS PER TABLE ° EMBEDMENT 20. ALL WOOD BUCKS LESS THAN 1-1/2" THICK ARE TO BE i CONSIDERED 1X INSTALLATIONS. 1X WOOD BUCKS ARE OPTIONAL IF UNIT IS INSTALLED DIRECTLY TO SUBSTRATE. WOOD BUCKS DEPICTED AS 2X ARE 1-1/2" THICK OR GREATER. 1X TYP. ANCHOR TYPE, AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED TO PROPERLY _ EMBEDMENT AND EDGE TRANSFER LOADS TO THE STRUCTURE. WOOD BUCK DESIGN DISTANCE PER SUBSTRATE, AND INSTALLATION IS THE RESPONSIBILITY OF THE ENGINEER SEE TABLE 20. OR ARCHITECT OF RECORD. ANCHORED THROUGH FRAME DIRECTLY INTO CONCRETE/CMU. 3) VISIBLE LIGHT WIDTH OR HEIGHT (ALSO REFERRED TO AS DAYLIGHT OPENING) IS MEASURED FROM BEADING TO BEADING. VERTICAL SECTION B-B TARI F qn. —� �— 1/4" MAX. SHIM 1. EMBEDMENT EDGE DISTANCE TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 20 & NOTE B FOR HEAD TYPE. 1/4" MAX. SHIM /7-77-7- MIAMI-DADE APPROVED MULLION, FBC COMPLIANT ALUMINUM/STEEL FRAMING OR STEEL STUD. MAY BE VERTICAL OR HORIZONTAL. SEE SUBSTRATE PROPERTIES, TABLE 20. Min. Edge Min. Anchor Substrate Distance I Embedment Southern Pine (SG=0.55) 9/16" 1-3/8" Steel, 18-8-8 410 Aluminum, 6063-T5 min. 3/8" 0.063" or SS Screw A36 Steel 3/8" 0.063" Steel Stud, Gr. 33 min. 3/8" 0.045" (18 Ga) Concrete (min. 3.35 ksi) 1" 1-3/4" 1/4" 410 SS CreteFlex Ungrouted CMU, (ASTM C-90) 2-1/2" 1-1/4" Southern Pine (SG=0.55) 1" 1-3/8" Concrete (min. 2.85 ksi) 1" 1-3/8" 1/4" Steel Ungrouted CMU, (ASTM C-90) 2-1/2" 1-1/4" Ultracon Southern Pine (SG=0.55) 1" 1-3/8"' INSTALLATION OPTION 4 ANCHORED THROUGH FRAME INTO METAL TYP. ANCHOR TYPE, EMBEDMENTAND "EDGE DISTANCE PER SUBSTRATE, SEE TABLE 20. A) MIN. OF 3 THREADS BEYOND THE METAL SUBSTRATE. B) USE ONLY FLATHEAD ANCHORS IN HEAD AND SILL. PAN/HEX/FLAT HEAD TYPE IS ALLOWABLE FOR ANCHORS IN THE JAMBS. C) "UNGROUTED CMU" VALUES MAY BE USED FOR GROUTED CMU APPLICATIONS. ao W z o U) W 01 > nab 0 Ho 00 O O a}oa (D N z L O O c�i LU U) z 00 LL O � cn W -) O z = W (0 ' = NE J J I� �g z ¢ ON ~ C7 NM 0 O � r U) p z a ° Z C C� W J W J IL -I O O Q ® � 0 W aayS O z D = O o O Q LU F- U _ J Q Z aµil �asaQ saua5 \I11111111//� ow( LYNX _Z�� ' •LICENSE �/ll /� No.58705 - T �® 7�i �i '•.�OR.... ® E �/'/S®I INAL A. LYNN MILLER, P.E. P.E.# 58705 INSTALLATION OPTION 5 ANCHORED THROUGH FIN INTO 2X WOOD FRAME OR BUCKSTRIP. TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 21. EDGE DISTANCE EDGE DISTANCE BUCK HEIGHT EXTERIOR a EMBEDMENT EDGE EDGE DISTANCE I~ DISTANCE i I I 0 1 4XI 1/4" MAX SHIM EMBEDMENT 1/4" MAX. SHIM 12"LENGTH,CENTERED ABOVE SASH TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 21. VISIBLE LIGHT HEIGHT 52 If 1/4" MAX SHIM NOTES: INSTALLATION OPTION 5 ANCHORED THROUGH FIN INTO 2X WOOD FRAME OR BUCKSTRIP. SASH VISIBLE �I LIGHT WIDTH Kn EXTERIOR 14 15 EDGE DISTANCE f 1/4" MAX SHIM I f TYP. ANCHOR TYPE, EMBEDMENT AND EDGE U DISTANCE PER SUBSTRATE, I SEE TABLE 21. FIXED VISIBLE LIGHT WIDTH BUCK WIDTH i) HORIZONTAL SECTION A -A (SHOWN WITH I.G. GLAZING) EXTERIOR n R V MIAMI-DADE APPROVED MULLION, FBC COMPLIANT ALUMINUM/STEEL FRAMING OR STEEL STUD. MAY BE VERTICAL OR HORIZONTAL SECTION C-C HORIZONTAL. SEE SUBSTRATE (SHOWN WITH MONO. GLAZING) PROPERTIES, TABLE 21. 1) USE ONLY SUBSTRATE -APPROPRIATE ANCHORS LISTED ON TABLE 21. FOLLOW EMBEDMENT AND EDGE DISTANCE EDGE DISTANCE LIMITS. ANY INSTALLATION OPTION SHOWN MAY BE USED ON ANY SIDE OF THE WINDOW. EDGE DISTANCE 1 'I EMBEDMENT TYP. ANCHOR TYPE, EMBEDMENT INSTALLATION OPTION 5 AND EDGE DISTANCE PER ANCHORED THROUGH FIN INTO 2X SUBSTRATE, SEE TABLE 21. WOOD FRAME OR BUCKSTRIP. VERTICAL SECTION B-B 2) VISIBLE LIGHT WIDTH OR HEIGHT (ALSO REFERRED TO AS DAYLIGHT OPENING) IS MEASURED FROM BEADING TO BEADING. 3) ANCHOR TO BE INSTALLED WITHIN 2-1/2" OF FIN CORNER. TART F ?I EDGE DISTANCE EMBEDMENT if 1/4" MAX. SHIM INSTALLATION OPTION 6 ANCHORED THROUGH INTEGRAL FIN INTO MET/ TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE 21. Anchor Substrate Min. Edge Distance Max. I O.C. Min. Embedment 2-1/2" x .113" Box Nail Southern Pine (SG=0.55) 5/16" 5" 2-7/16" 2-1/2" x .131" Common Nail Southern Pine (SG=0.55) 3/8" 5" 2-7/16" 2-1/2" x .145" Roofing Nail Southern Pine (SG=0.55) 3/8" 5" 2-7/16" 2-1/2" x .145" Roofing Nail Southern Pine (SG=0.55) 3/8" 5" 2-7/16" #10 Steel Trusshead Screw or #12 Steel, 18-8 or 410 SS Screw Southern Pine (SG=0.55) 1/2" 5" 1-3/8" 0.125" Aluminum, 6063-T5 min. 5/16" 5" 0.09" 0.050" A36 Steel 5/16" 5" 0.050 " 0.045" (18 Ga) Steel Stud, Gr. 33 min. 5(16" 1) MIN. OF 3 THREADS BEYOND THE METAL SUBSTRATE. W Z O )> > nab w o �o (� > O i- > o O a}oQ 0 N Zw Q O O M � cn z _1 O al � Z LL � = J W O U U O OO J - �� ~ Q � UMOJQ a N W 0 9MO > r- W p o U) Z Z 0 Z 0 W J W J 0 O (D W rn N Z #N aa4S = O z ~ U = O Q o U O J Z J LU (5H = J Q Z a�}�1 asap sauaS i No. 58705 ,�13®ST �Z4/ TE F i '•.FLORiDP.•' GO�� ss®NAL 0\ A. LYNN MILLER, P.E. P.E.# 58705 .062" 2.724" -� t 2.560" I I O HEAD, FLANGE FRAME 2.724" 1 3.651 " O SILL, FLANGE FRAME 2.105" Ali .273" 11 SASH PULL RAIL ® 2.724" I O2 HEAD, INTEGRAL FIN FRAME 2.724" -1 s SILL, INTEGRAL FIN FRAME 4.276" 2.149" � -�{ 1.300" �-- 062" 1.136" 1.300"F? . 1001, 1 i 1 1z SASH LOCK RAIL 13 SASH TOP & BOTTOM RAIL 2.724" O3 HEAD,EQUAL LEG FRAME 2.724" -1 3.151" O SILL, EQUAL LEG FRAME 2.211" 1 1.803" 1 170" 1.488" i I 2.786" 062" -�► OJAMB, FLANGE FRAME 10 SILL ADAPTER � 2.211" 1.138" 14 HD MEETING RAIL 15 STD MEETING RAIL I I 3.908" .0E 2.112" 1 I 1 2.786" OJAMB, INTEGRAL FIN FRAME 040" --� 1.513" 1 �{ .808" ►-- INSTALLATION 17 HOLE COVER 11 1.415" �{ � 062"i�I .710" _� 19 SILL TRACK 109 .360" --- 1.032" .045" i 8SCREEN ADAPTER --► -►- .050" -�1 .045" TABLE 22: MATERIAL PROPERTIES USED HOT -MELT ALUMINUM SILICONE BUTYL i FOR ANCHORAGE CALCULATIONS: STRUCTURAL REINFORCEMENT .795" 795" -► .492" .612' 23 7/16" BEAD 24 5/16" BEAD Material Min. Fy Min. F. Steel Screw 92 ksi 120 ksi 18-8 Screw 60 ksi 95 ksi 410 Screw 90 ksi 110 ksi Elco UltraCon® 155 ksi 177 ksi 410 SS Elco CreteFlexO 127.4 ksi 189.7 ksi 6063-T5 Aluminum 16 ksi 22 ksi A36 Steel 36 ksi 58 ksi Gr. 33 Steel Stud 33 ksi 45 ksi POLYISO- 1/4" NOM. 3/16" NOM. BUTYLENE WITH STRUCTURAL BUTYL& DESICCANT SILICONE DESICCANT - FOAM WITH FOAM EXT. GLASS DESICCANT EXT. G EXT. GLASS INT. GLASS INT. GLASS KODISPACE SUPER SPACER° 70 4SG TPS 71 NXT TM 987" ►-- 1 2.786" .062" �- 0JAMB, EQUAL LEG FRAME 062" .723" --1 .875" ►- 1s WIND LOAD ADAPTER 1.446" L 518" r1 040" z0 ANTI -LIFT CLIP - 1 .630" .070" P7:9;-71 z1A IG BEAD DURASEAL° 72 SPACER .464" 798" j- 065' _ I POLYISOBUTYLENE SEAL 16" NOM. ROLL -FORMED STAINLESS STEEL EXT. GLASS GLASS 2 BB IG SNAP BEAD DESICCANT FILL 5/16" NOM. ?:� SILICONE SEAL XL EDGETM 73 SPACER GLASS U 00 Y LU ? > � O 07 nab w M O _ �o m O cA U' CV o O Q a}oa Z L O - w J M of (q O Z C� O -1 O o. u) = - Z W O Z (D 02 t,j•J N ti `=, g ~ Z Q F_ 'ONLu 7 U 0Mo > Of d' a to Z O Z rn a Of rn J O 0 O � rn ® N N }aays F O D 07 Z L O o Z rr Lli U J x = Q W a}�Jl0sa0 saua5 \\\Ililllfl//`!0 \ O V • LYIV�V No .5S7®5 e�® ' SATE O ' �<(/� ®/VAL 0-o\\�e //// I P l l 1 00\ A. LYNN MILLER, P.E. P.E.# 58705 TARI F 93 Item # Part # Description Material 1 624038 Head, Flange Frame Alum. 6063-T6 2 624039 Head, Integral Fin Frame Alum. 6063-T6 3 624040 Head, Equal -leg Frame Alum. 6063-T6 4 624001 Jamb, Flange Frame Alum. 6063-T6 5 624017 Jamb, Integral Fin Frame Alum. 6063-T6 6 624028 Jamb, Equal -leg Frame Alum. 6063-T6 7 624035 Sill, Flange Frame Alum. 6063-T6 8 624036 Sill, Integral Fin Frame Alum. 6063-T6 9 624037 Sill, Equal -leg Frame Alum. 6063-T6 10 624034 Sill Adaptor Alum. 6063-T6 11 624043 Sash Pull Rail Alum. 6063-T6 12 624006 Sash Lock Rail Alum. 6005A-T61 13 624041 Sash Top & Bottom Rail Alum. 6063-T6 14 624027 HD Meeting Rail Alum. 6063-T6 15 624005 Std. Meeting Rail Alum. 6005A-T61 16 624047 Screen Adapter Alum. 6063-T6 17 624051 Installation Hole Cover Alum. 6063-T6 18 64125M Windload Adapter Alum. 6063-T6 19 624042 Sill Track Alum. 6063-T6 20 624015 Anti -Lift Clip Alum. 6063-T6 21A 624009 IG Bead Alum. 6063-T5 21B 624011 IG Snap Bead Alum. 6063-T5 23 624026 7/16" Lami Glaz. Bead Alum. 6063-T6 24 624013 5/16" Lami Glaz. Bead Alum. 6063-T6 30 6TP247 Glazing Bead, Bulb Vinyl for #624013 & #624026 Vinyl 31 6TP248 Glazing Bead, Bulb Vinyl for #624009 & #624011 Vinyl 32 712653K Mono setting Block 3/32" X 1/4" X 1" Neoprene 33A 71715K Lami IG Setting Block 1/8" x 3/4" x 1-1/14" Neoprene 33B 624014 IG Snap Setting Block Vinyl 35 724045 Sweep Latch Cast ZJnc 36 71298 Weep Hole Cover Vinyl 37 41722 Hole Plug Vinyl 38 724021 Lock Rail Cover, (LH & RH) Vinyl 39 724050 Pull Rail End Cap Vinyl 40 724048 Roller Housing & Sash Guide Vinyl 41 724052 Roller Wheels Brass 42 724054 Sash Top Rail Gasket, (LH & RH) Polyethylene 43 724055 Sash Bot Rail Gasket, (LH & RH) Polyethylene 44 724057 Frame Header Gasket, (LH & RH) Polyethylene 45 724058 Frame Sill Gasket, (LH & RH) Polyethylene 46 724063 Meeting Rail Gasket Polyethylene 50 Weatherstrip, .187" x .170", Fin Seal @ Sash 51 Weatherstrip, .187" x .270", Fin Seal @ MR 52 67070 Bulb Vinyl 60 71OX38PPAX #10 X3/8" Ph. PH SMS (Windload Adapter) Stainless Steel 61 781PQX #8 X 1" Qd. PH SMS (Frame & Sash Assembly) Stainless Steel 63 - Aluminum Screen with Fiberglass Mesh Varies 70 - Kommerling Kodispace 4SG TPS See Sheet 18 for Materials 71 - Quanex Super Spacer nXT 72 - Quanex Duraseal Spacer 73 - Cardinal )C Edge Spacer 74 - I Dow 791, 899 or GE 7700 Backbedding Silicone ASSEMBLY DETAILS FOR 2 cf � - INTERIOR 61 111—'�:n NOTES: 1) ALL CORNERS TO USE GASKET AND/OR SEALANT. 2) SOME PARTS/OPTIONS NOT SHOWN ON DRAWING FOR CLARITY. 'tppmad Fbddo Buidin Cold Dam 3aI bade Proded Bud 0 U 00 LU > z � OQf U) > nay w M co > O x o o cn >LLJ > w O Q a}oa (� N z O M �� U) Oz Q J O a v> _ J Z 33 ZLL°D x v w� z o f uaa� a N � F-OM SM0 O � p a U) Z Z `. o Of CY) J J LL O w O ® rn N_ CN IY cr_ aayS Ow = Z o O o 06 ti LLJ O = Q 00 aµ}l -asaa sauaS ��•'� LICENSE •. /l�� No. 58705 TATE OFPZO ALI��,� A. LYNN MILLER, P.E. P.E.# 58705