HomeMy WebLinkAboutCT RV 19-0621.01 copy 2
NOA No.: 19-0621.01
Expiration Date: 09/23/24
Approval Date: 09/26/19
Page 1 of 4
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
CertainTeed Corporation
20 Moores Road
Malvern, PA 19355
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction mat erials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to be
used in Miami Dade-County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami-Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If th is product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been desi gned to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: CertainTeed Ridge Vent - 12" Unfiltered
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA 15-0831.06 and consists of pages 1 through 4.
The submitted documentation was reviewed by Freddy Semino
NOA No.: 19-0621.01
Expiration Date: 09/23/24
Approval Date: 09/26/19
Page 2 of 4
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub-Category: Ventilation
Material: Plastic
Minimum Slope: 3:12
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT
Product
Dimensions
Test
Specifications
Product
Description
CertainTeed Ridge
Vent - 12" Unfiltered
Length: 48"
Width: 13.8"
Height: 7/8"
TAS 100(A) Polypropylene plastic low profile ridge vent with an
integral end plug for installation in asphaltic shingle
roof systems.
MANUFACTURING LOCATION
1. Orrick, MO
EVIDENCE SUBMITTED
Test Agency Test Identifier Test Name/Report Date
Architectural Testing 65457.01-109-18 TAS 100 07/26/06
D8316.01-801-18 TAS 100 (A) 09/16/14
D8316.02-801-18 TAS 100 (A) Calibration 12/02/14
Hurricane Engineering & Testing, HETI-09-F400 ASTM D 1929 07/01/09
Inc. HETI-09-T102 ASTM D 638 01/30/09
HETI-02-A001 ASTM G 155 09/13/02
PRI Construction Materials AVIG-010-02-01 ASTM D 635 12/02/14
Technologies ASTM D 1929 12/02/14
ASTM D 2843 12/02/14
AVIG-010-02-02 ASTM G 155 06/09/15
NOA No.: 19-0621.01
Expiration Date: 09/23/24
Approval Date: 09/26/19
Page 3 of 4
APPROVED APPLICATION
Trade name: CertainTeed Ridge Vent - 12" Unfiltered
System Type A: Mechanical attachment of ridge vent over composite shingles.
Cutout: Cut a 1 ½" slot along the apex of the roof by cutting ¾" on each side of the ridge. The
slot shall terminate approximately 6" from each rake edge.
Installation: Center the vent over the slot. Install ridge vent using corrosion resistant roofing nails of
0.120" shaft diameter x 0.320" head diameter x 3" long and of sufficient length to
penetrate through the wood sheathing a minimum 3/16". Place the nails in each preformed
nail boss, two at each end, 15" from each end, and the center of each vent section.
Install pre-manufactured or field cut ridge shingles over the ridge vent in compliance
with the shingle manufacturer’s current approved Notice of Acceptance, and the shingle
and ridge vent’s installation instructions. Nails shall be of sufficient length to penetrate
through the sheathing a minimum 3/16".
Ventilation Calculations: Refer to manufacturer’s published literature
Minimum Slope: 3:12
LIMITATIONS:
1. Refer to applicable building codes for required ventilation.
2. CertainTeed Ridge Vent shall not be installed on roof mean heights greater than 33 feet.
3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
4. All plastic ridge vent manufacturers shall have an unannounced follow-up quality control program from an
approved listing agency. Follow-up test results shall be made available to the Miami-Dade Product Control
Office upon request.
5. All approved products listed herein shall be labeled and shall bear the imprint or identifiable marking of the
manufacturer's name or logo, city and state of manufacturing facility, and following statement: "Miami-Dade
County Product Control Approved" or the Miami-Dade County Product Control Seal as shown below.
NOA No.: 19-0621.01
Expiration Date: 09/23/24
Approval Date: 09/26/19
Page 4 of 4
DETAIL DRAWINGS
CERTAINTEED RIDGE VENT - 12" UNFILTERED
END OF THIS ACCEPTANCE