HomeMy WebLinkAboutengineer.pdfCONTRACTOR: KING CARTER A' TJMINUM
DESIGN CRITERIA:
Applicable Codes, Regulations, and Standards
1. The 5th Edition (2014) Florida Building Code, specifically Chapter 16 Structural
Design, Chapter 20 Aluminum, and Chapter 23 Wood.
2. AA ASM 35 and Specifications for Aluminum Structures, Part 1-A of the
Aluminum Design Manual prepared by The Aluminum Association, Inc.
Washington, D.C., 2005 Edition
3. ASCE 7-10.
Wind Loads
I. Building Occupancy Category, Paragraph 1604.5 and Table 1604.5:
Risk Category 1.
2. Basic Wind Speed, Figure 1609C, State of Florida Debris Region & Basic Wind
Speed, Paragraph 1609.3.1 and Table 1609.3.1 Equivalent Basic Wind Speed:
VMT =150 MPH, VASD =116 MPH
3. Exposure Category, Paragraph 1609.4.3: Exposure B
4. Building Category for Aluminum Structures, Paragraph 2002.6: Building
Category 1 - Carport•. Non -Habitable, Unconditioned
Roof Type
1. Roof Type: MONOSLOPE
2. Roof Material: 3" x 48" x 0.024" composite panel Elite 2000, 1.0 density
foam Florida Product Approval Number FL 7561-R3. 952-RI
Foundation Design
Existing concrete. No additional concrete footing or slab is required to resist the
loads imposed pon the existing slab by the proposed construction if the existing
slab is a minimum of 4" thick and in sound condition, free from structural
cracking, spelling, or other deterioration.
Specifications
The following specifications are applicable to this project:
1. All work shall be in accordance with the 5th Edition (2014) Florida Building Code,
and any other applicable local codes and regulations.
2. Aluminum extrusions shall be 6005 T5 Alloy. Due to quality control issues, no
manufacturer substitution is acceptable without the specific written, signed and
sealed authorization of Suncomt Aluminum Engineering, LLC.
3. Screen Material: Design based on 18114 or 20/20 Better View. Any other material
must be approved.
4. Fasteners are required to be corrosion resistant, minimum SAE Grade 2 or better
zinc plated to ASTM B633, or coated stainless steel series "300", or uncoated
stainless steel series "400".
5. All Self Mating Beam Sections are to be stitched with either #14 screws 6" from
ends and 24" center to center or # 12 screws 6" from ends and 12" center to center.
6. Where concrete specifications are required, whether in the screen enclosure scope
or not, by one or more regulatory agency, the following specifications are
applicable:
a. Concrete shall conform to ASTM C94 for the following components:
i. Portland Cement Type 1,- ASTM C 150
ii. Aggregates - Large Aggregate 3/4" max - ASTM C 33
iii. Air entraining+/- 1%- ASTM C 260
iv. Water reducing agent - ASTM C 494
v. Clean Potable water
vi. Other admixtures not permitted
b. Metal accessories shall conform to:
i. Reinforcing Bars - ASTM A615, grade 60
ii. Welded wire fabric - ASTM At 85
c. Concrete slump at discharge chute not less than 3" or more than 5". Water
added after botching is not permitted.
d. Prepare and place concrete per American Concrete Institute Manual of
Standard Practice, Parts 1, 2, and 3 including hot weather recommendations.
e. Moist cure or polyethylene curing permitted.
f. Prior to placing concrete, treat the entire subsurface area for termites in
compliance with the FBC.
g. Concrete shall be placed over a polyethylene vapor barrier.
h. All aluminum components embedded within concrete shall be coated with a
bituminous paint or epoxy.
7. All flashing and weatherproofing shall be provided by the contractor.
8. Door location shall be determined by contractor in the field.
9. Use of these plans acknowledges and accepts a limit of liability not to exceed
design and engineering fee.
WIND SPEED ANT XPOSURE HAVE
BEEN DETERMIN- . USING THE ADVANCED
TECHNOLOGY COUNCIL'S WEBSITE
AND GOOGLE EARTH.
f $•_6" f
of EXISTING
o SHED
3"X48"XO.024"
COMPOSITE PA
F
O
I
i�
3X3XO.093
POST
N
I
00
t
CONCEALED FASTENERS OR ATTACHMENTS
ARE THE RESPONSIBILITY OF THE
0N.TRACTOR OF RECORD
THESE PLANS AND ALL PROPOSED WOIi
ARE SUBJECT TO ANY CORRECTION:
REQUIRED BY FIELD INSPECTORS TKA:
r, fAAY BE NECESOARY IIJ ORDER TO
t;OP,4PLYl'�fTNi �;LLr�PPLfC�'L�':� COGEt.
NEL
EXISTING
SHED
EXISTING
SHED
BEAM
3"X48"XO.024"
- 1.0 DENSITY FOAM -
COMPOSITE PANEL
A-3
2X4SMB 2X5SMB
EDGE 4TH WALL
BEAM BEAM
At D YI nNIIT_ N iF 5T i�.Er
to
I
00
I
I 1
6'-0" 1'i•-6n
6"
L 6'-0" -J
%
-
LU
O yy _
V T 0 F-
a o Z_
�I'9�0¢'•
... t\ BUJ
Z_
U 9
= J N
J 1.9 F
F Z
to 2,rm
QLU �LL T
Z (.7'iiann
C
Ln W � k
to
to w
LU
Cr r
O
2X2 K.B. A-2
0 Z
(TYP)
oLLI
a
W_
to i0
3X3XO.093 3X3XO.093
POST
j1
W it °• m
¢ O 1- v
POST
OLLJ LL Kos
rn rn
a toW u-W
DRAWN BY
MC
DATE DRAWI
07/17/17
REVISION
EXISTING BRICK
A -a
KNEE WALL
W-6"
3
Q
nee o:
6"
ks
ALUMINUM MEMBERS DIMENSIOV-
HOLLOW SECTIONS
2 x2:
2"x2"x0.046"
2 x3:
2"x3"x0.050"
2x4:
2"x4"x 0.050"
2 x5:
2"x5"x 0.050"
OPEN BACK SECTIONS
1 x 2: 1" x 2" x 0.040"
1 x 3: 1" x 3" x 0.045"
SNAP SECTIONS
2 x 2 Snap: 217 x 2" x 0.045"
2 x 3 Snap: 2" x 3" x 0.050"
2 x 4 Snap: 2" x 4" x 0.045"
SELF MATING (SMB)
2 x 4 SMB:
2" x 4" x 0.044" x 0. 100"
2 x 5 SMB:
2" x 5" x 0.050" x 0.100"
2x6SMB:
2"x6"x 0.050"x0. 120"
2 x 7 SMB:
2" x 7" x 0.057" x 0.120"
2 x 8 SMB:
2" x 8" x 0.072" x 0.124"
2 x 9 SMB:
2" x 9" x 0.072" x 0.124"
2 x 10 SMB:
2" x 10" x 0.092" x 0.398"
MINIMUM FASTENER EDGE DISTANCE: 1/2"
MINIMUM FASTENER SPACING: 3/4"
CONCRETE SCREW ANCHOR:
SIMPSON TITEN HD OR EQUIVALENT
SHEET METAL SCREWS ISMS):
ITW / BUILDEX OR EQUIVALENT
F-
#14',
1 1/2" C
FACED WAI
rS-1 SER PAN TO POST (cd 4TH WALL DETAIL
A-2 SCALE: NTS
(2) 3/8" DIA. CONCRETE
(3" CONC. EMBED)
3" x 0.0u,
INTERNAUEXTERNAL
3" x Tx 1/8" EXTRUDED
POST BASE W/ (2) 3/8"
DIA. THRU BOLTS
14
B 3" x 3" POST TO CONCRETE CONNECTION DETAIL
A-2 SCALE: NTS
#14 x 4 7/8" SMS W/
1 112" DIA. NEOPRENE
FACED WASHER ® T O.C.
1 UTx2 118"x1112"x0.08T
ALUM RECEIVING CHANNEL
W/ (3) #12 x 314" SMS EACH
SIDE OF BEAM & (2) 30' DIA
THRU BOLTS INTO THE POST
3/8" DIA THRU BOLT
(3) TOTAL
2"x6"SMS
S-2 ISER PANEL TO CORNER POST a 4TH WALL DETAIL
A SCALE: NTS
3" x 0.052" ALUM
RECEIVING CHANNEL
W/ #10 x 3/4" TOP AND
BOTTOM AS END CAP
.v fie dui®pJ
014 x 4718"SMS W/
1 1/2" DIA. NEOPRENE
FACED WASHER ® 8' O.C.
COMPOSITE
1 1/2" x 2 1/8" x 1 1/2" x 0.062" ALUM
RECEIVING CHANNEL W/ (3)
#12 x 3/4" SMS EACH SIDE OF
BEAM & (2) 3/8" DIA. THRU BOLTS
INTO POST
S RISER PANEL TO CORNER POST CONNECTION
A-2 SCALE: NTS
T COMP
Moil,"
2" x 2" x 0.040"
KNEE BRACE
11/2"x2 M8"x 1177-x
0.062" x 2" LONG ALUM
RECEIVING CHANNEL W/ (3)
#12 x 3/4" SMS EA FACE &
(3) #12 x 3/4" INTO POST
-' KNEE BRACE CONNECTION DETAIL
A SCALE: NTS
Lj
0 u a
W a
LL a�a G
K K m Q
LU �E a
W i /
Z Zw Q
l7 �� O
S
Wf-
N
W
K O
Q W W
o
O 0
N:
LU W
LLI K o rn
K WU-0M
CL coe D O -1
MC
DATE DRAWN
07/17/17
REVISION
L
z -
SHEET NO:
A-2