HomeMy WebLinkAboutNOA; Titanium Synthetic UnderlaymentsWC�7tiM "Y
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE. -OF -ACCEPTANCE (NOA)
3Z9Z3 iviassron way
Mission, BC, Canada V2V-6E4
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 209
Miami, Florida 33175-2474
T (786)315-2590 F (786) 31525-99
www.miamidade.eov/economv
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation.submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to
have this product or material tested for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to
revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Titanium® UDL-25 PLUS, Titanium' UDL-30, Titaniure UDL-50, UDL TT, VDL T F',
UD1_TTMC-300, RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and
RhinoRoof RSA Synthetic Underlayrrments
LABELING: Each unit shall bear a permanent label with the manufacturers name or logo, city, state and following
statement. "Miami -Dade County Product Control Approve&% unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes small automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT. The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, there it shalt be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors mad
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No, 13-0610..01 and consists of pages I through 5.
The submitted documentation was reviewed by Alex Tigers. FILE COPY
ILE®pY
Aq NOA No.: 14-0603..18
Mi at��•uaue coin Expiration Date: 08108/18
Approval Date` 06111/15
Page 1 of 5
A
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: Polypropylene
SCOPE:
This acceptance is for Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium' UDL-50, UDL TT, UDL TF,
UDL TTMC-300, RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA
Synthetic Underlayments as described in this Notice of Acceptance, for use with approved prepared roof assemblies
where ASTM D226 Type underlayment is specified and installed with prescribed approved fasteners and fastener
densities. Designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the
Florida Building Code
PRODUCT "DESCRIPTION:
Test
Product
Product
Dimensions
Suecification
Description
Titanium® UDL-25 PLUS
48" x 250' rolls
ASTM D226
Woven synthetic polymer underlayment with one
Manufacturing
Type I & H
side coated with UV protected and slip resistant
Location #1 & #3
polymer stabilized polypropylene on both sides.
Titanium® UDL-30
48" x 250' rolls
ASTM D226
Woven synthetic' polymer underlayment with two
Manufacturing
Type I & 11
sides coated with UV protected and slip resistant
Location #1 & #3
polymer stabilized polypropylene on both sides.
Titanium' UDL-50
48" x 250' rolls
ASTM D226
Woven synthetic polymerunderlayment with two
Manufacturing
Type I & H
sides coated with UV protected and slip resistant
Location #1& 43
polymer stabilized polypropylene on both smiles,
UDL TT
48" x 250' roils
ASTM D226
Woven synthetic polymer underlayment with one
Manufacturing
Type I & H
side coated with UV protected and slip resistant
Location #1
polymer stabilized polypropylene on both sides.
UDL TF
48" x 250' rolls
ASTM D226
Woven synthetic polymer underlayment with two
Manufacturing
Type I & U
sides coated with UV protected and slip resistant
Location 41
polymer stabilized polypropylene on both ,sides..
UDL TTMC-300
48" x 250' rolls
ASTM D22,6
Woven synthetic polymer underlayment with two
Manufacturing
Type I & H
sides coated with UV protected .and slip resistant
iLocation #2 ,
polymer stabilized polypropylene on both sides..
RhinoRoof U10
42" x 286' rolls
ASTM D226
Woven synthetic polymer underlayment with two
Manufacturing
Type I & H
sides coated with UV protected a nd slip resistant
Location #3
polymer stabilized polypropylene on both sides.
NOA No.: 14-0603.18
MIAMI•DADE COUNTY Expiration Date: 08/08/18
Approval Date: 06/11/15
Page 2 of 5
RhinoRoof U15
Manufacturing
Location #3
RhinoRoof U20
Manufacturing Location #3
Titanium UDL25
Manufacturing Location #3
42" x 286' rolls ASTM D226 Woven synthetic polymer underlayment with two
Type I and H sides coated with UV protected and slip resistant
polymer stabilized polypropylene on both sides.
42" x 286' rolls ASTM D226 Woven synthetic polymer underlayment with two
Type I and H sides coated with UV protected and slip resistant
polymer stabilized polypropylene on both sides.
48" x 250' rolls ASTM D226 Woven synthetic polymer underlayment with two
Type I and 11 sides coated with UV protected and slip resistant
polymer stabilized polypropylene on both sides.
RhinoRoof RSA 36" x 67' rolls ASTM D 1970 Unreinforced polymer modified bitumen material
Manufacturing Location #4 adhered to the underside of a polymer -coated,
synthetic woven sheet. The underside is backed
with a release film.
MANUFACTURING LOCATIONS:
1. ML1
2. ML2
3. ML3
4. ML4
EVIDENCE SUBMITTED:
Test ALYencv
Test Identifier
Test Name/Report
Date
hitertek Testing Services
#3031783
TAS 104
02/19/03
3119607COQ=003B
ICC-ES AC48
02/20/08
3124826-01
ASTM E108
02/19/08
3124826MID-007
ASTM E108
02/25/08
311801000Q-003
ASTM D226
02/20/08
3130639COQ-002A
ASTM D226
02/20/08
3146738COQ-003A
ASTM D226
06/20/11
3146738COQ-003B
ASTMI) 1876/ TAS 117
03/28/08
101465036COQ-001
.ASTM D1970
06/27/14
100539395COQ-006
ASTM D226
06/02/14
101863861COO-001A
ASTM D226
10/28/14
101823107COQ-011
ASTM D.226
12/09/14
Trinity 1 ERD
It5010.05.10
ASTM D4798 / D.226
05/14/10
138010,08,11
ASTM D226
09/11/11
135520.08.11
ASTM D25.23 / D1781
08/17/11
MIAMI•DADE COUNTY
1�i0A No.: 14-0603.18
• � M • , Expiration Date: 08/08/18
Approval Date: 06/1.1115
Page 3 of 5
INSTALLATION S.P_ECIFICATIONS;:...., _
Titanium®`,UDL 25 - PLUS; Titanlum-_._Uff&30, Titanium`' UDL-50, UDL TTMC-300, UDL TT, UDL TF,
1m Rho _ 6of U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments
1. Titanium® UDL-25 PLUS, Titanium' UDL-30, TitaniunP UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall be installed in strict compliance with applicable Building Code.
2. Titanium`s UDL-25 PLUS, Titanium' UDL-30, Titanium' UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall be installed with a minimum 4-inch head lap in a shingle layer fashion.
3. TitaniunP UDL-25 PLUS, Titanium' UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, and Titanium UDL25 Synthetic Underlayments shall be
fastened with Miami -Dade approved corrosion resistant tin -caps and 12 gauge 1 1/4' annular ring -shank nails,
spaced 6" o.c. at all laps and three staggered rows fastened 12" o.c. in the field of the roll.
4. TitaniunP UDL-25 PLUS, Titanium' UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments may be used with Asphaltic shingles, Wood shakes and shingles, Non-structural metal roofing,
and quarry slate. Titanium® UDL-30, Titanium® UDL-50, UDLTTMC-300, UDL TT, UDL TF, RhinoRoof
U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25 and RhinoRoof RSA Synthetic Underlayments shall
not be used as roof tile underlayments.
5. For Roof Tile applications; TitaniumO UDL-25 PLUS may be used as an anchor sheet in roof tile applications
when used in combination with a top membrane layer, consisting of a Miami -Dade approved TAS 103 self -
adhering underlayment. (See current NOA listing of approved TAS 103 self -adhering underlayment for
installation guidelines and limitations of use).
6. For fire classification of specific roof assemblies using TitaniumO UDL-25 PLUS, Titanium`s UDL-30,
TitaniunP UDL-50, UDL TTMC-300, UDL TT, UDL TF, RhinoRoof U10, RhinoRoof U15, RhinoRoof U20,
Titanium UDL25, and RhinoRoof RSA Synthetic Underlayments_refer to a current Approved Roofing
Materials Directory for fire ratings of this product.
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly
evaluate the installation of this material,
NOA No.: 14-0603.18
Expiration Date: 08/08118
Approval Date: 06/11/15
Page 4 of 5
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code.
3. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall be applied to a smooth, clean and dry surface with deck free of irregularities. All nails in
the deck shall be carefully checked for protruding heads. Re -fasten any loose decking panels. Sweep the deck
thoroughly to remove any dust and debris prior to application.
4. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall not be hot mopped, refer to manufacturer's published literature for product compatibility.
5. Titanium® UDL-25 PLUS, Titaniumr UDL-30, Titaniumr UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, . RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall not be applied over an existing roof membrane as a recover system.
6. Titanium® UDL-25 PLUS, Titanium UDL-30, Titanium UDL-50, UDL TTMC 300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall not be left exposed as a temporary roof for longer than 30 days of application.
7. UDL TTMC-300 Synthetic Underlayment shall not be left exposed as a temporary roof for longer than 180
days of application.
8. Titanium® UDL-25 PLUS, Titanium' UDL-30, Titanium' UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments are components used in roof system assemblies. Roof system assemblies are approved under a
specific Notice of Acceptance. Refer to Prepared Roofing system Product Control Notice of Acceptance for
listed approval of this product with specific prepared roofing products.
9. Titanium UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20., Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments may be used with any approved roof covering Notice of Acceptance listing Titaniure UDL-25
PLUS, Titanium UDL-30, Titaniure UDL-50, UDL TTMC-300, UDL TT, UDL TF, RhinoRoof U10,
RhinoRoof U15, RhinoRoof U20, Titanium UDL25, And RhinoRoof RSA Synthetic Underlayments as a
component part of an assembly in the Notice of Acceptance. If Titanium' UDL-25 PLUS, Titaniue UDL-
30, Titanium® UDL-50, UDL TTMC300, UDL TT, UDL TF, RhinoRoof U10, RhinoRoof U15, RhinoRoof
U20, Titanium UDL25, and RhinoRoof RSA Synthetic Underlayments are not listed, a request may be made
to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department for
approval provided that appropriate documentation is provided to detail compatibility of the products, wind
uplift resistance, and fire testing results.
10. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo
and the following statement: "Miarni-Dade County Product Control Approved" or the Miami -Dade County
Product Control Seal as shown below.
IIAMFDADE COUNTY
•
11.. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 61G20-3 of the Florida Administrative Code,
END OF THIS ACCEPTANCE
NOA No.: 14-0603.18
Expiration Date: 08108/18
Approval Date: 06111/15
Page 5 of 5