HomeMy WebLinkAboutLomanco Ridge VentDEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
FlUllrll,tH'D€MIAMI-DADE COUNTY
PRODLTCT CONTROL SECTION
1 1 805 SW 26 Street, Room 208
Miami, Fiorida 33 11 5 -24'7 4
T (786) 315-2s90 F (786)3ts-2s99
ruww.miamidade.gor'/economvNOTICE OF ACCEPTA}ICE OA
Lomanco, lnc.
2101West Main Street
Jacksonville, AR72076
Scoru:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be
used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(in Miami-Dade County) and/or the AHJ (in areas other than Miami-Dade County) reserve the right to have this
product or material tested for quality assurance purposes. Ifthis product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER resen€s the right to revoke this acceptance,
if ii is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
Thls product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DpscmpuoN: vuR & LPR Ridgevents
La.ggLINCl Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statsment: "Miami-Dade County Product Control AFproved", unless otherwise noted herein.
RpNSWAL of this NOA shall be considered after a renewal application has been frled and there has been no change
in the applicable building code negatively affecting the performance of this product.
TgnVffNAnION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any secfion
of this NOA shatl be cause for termination and removal of NOA-
AOVSp11SEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirery.
IXSpgCffONi A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shail be available for inspection at the job site at the request of the Building Official.
This NOA reaews NOA No.11-0602.01 and consists of pages I through 4'
The submitted documentation was reviewed by Gaspar J Rodriguez.
NOA N*.: 1G0510.24
Expiration Date: 08117 121
Approval Date; 07 128116
Page 1 of4
RooprNc CouroNrxr APPRovs-
Category:Roofing
Sub-Catesorv: Ventilation
Material:Aluminum
Tnaor NaMsS OF PRODUCTS MANUFACTURED oR LABELED BY AppnCaNr:
Product
VUR Ridgevents
LPRRidgevents
MeN uracruRlNc LocarroN
1. Jacksonville, AR
EvrnsNcg Sus*{ttrgo:
Test Agencv
lntertek-ATl
TAS 100(A) Aluminum static louvered roof ridge
ventilation system.
TAS 100(4) Aluminum static louvered roof ridge
ventilation system.
Dimensions
2":Height
8.125":Width
i0':Length
0.025": Min. thickness
3-625": Heiglrt
9.875":Width
8'and 10':Length
0.025": Min. thickness
Test
Specification
Product
Descriotion
Test Identilier
F7517.01-801- 18
Test Name/Report
rAS 100(A)
Date
071081t6
NOA No.: 1G0510.24
Expiration Date: 08/17121
ApprovalDatet A1fi8116
P*ge2 of4
Arrnovsn AsspnaslrEs:
Trade trames:
System Type C:
Cutout:
Installation:
Ventilation
Calculations:
Minimum Slope:
VUR & LPR Ridgevent
Mechanical attachment of static ridge vent oYer composite shingles.
Refer to manufacturer's published literature
lnstall end plug on the end of the vent sealed with 100% silicone sealant. VUR & LPR
Ridgevent itratt Ue 6" longer than ventilation slot as to provide a base for the end plug.
Apply %" wide bead of 100% silicone sealant caulk to the bottom flange of the VUR & LPR
Ridgevent sections close to where roof hole will be after vent is installed. Align end of first
section on the end marks and the bottom of the nailing flange on the chalk line (4" down on
both sides of the ridge peak for VUR vent; 5%" down on both sides of the ridge peak for LPR
vent). Nail the VUR & LPR Ridgevent in place using 11 gauge 2" galvanized smooth shank
roofing nails through the factory formed holes, with the first nall lYz" to 2" form the vent end.
All nail heads and vent section joints shall be sealed with 100% silicone sealant.
lnstall Hurricane Straps over each end ofridge vent, all connections between sections andal3'
intervals over the remainder of the vent using four |Yz" galvanized ring shank-roofing nails per
strap.
Refer to manufacturer's published literature
3:12
NOA No.: 1G0510,24
Expiration Date: 08/17121
Approval Datet 07 128116
Page 3 of4
GgNBRAL Ltttrtt:artoNs:
l.
2.
4.
5.
Refer to applicable Building Code for required ventilation'
vuR & LPR Ridgevent shall comply with all applicable building codes.
VUR & LPR Ridgevent shall not be installed on roof mean heights greater than 33 feet'
vuR & LPR Ridgevent shall comply with the Florida Building code (FBC)
All products listed herein shall have a quality assurance audit in accordance with the Florida Building
Code and Rule 61G20-3 of the Florida Administrative Code.
Drranls
LPR Ridgevent
+75" arr
VUR Ridgevent
'iq
NOA No.: 16-$510.24
Expiration Datet 08/11 121
Approval Date: 07i28/16
Page 4 of 4
r 20"
END OF THIS ACCEPTANCE
I
l_
?,.REF
T_
:--.--- - ---- -::-:-:-:=i--:_
I