HomeMy WebLinkAboutProject InformationManual S Compliance Report Job: Lot 19 Block 5 Waterston...
-- wrightsoft! Date:
Ent/re House By: FLETCH
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCO WAY, SANFORD, FL 32771 Phone:407-333-2665 Fax:407-333-3853 Web: W W W.DEL-AIR.COM
Project
For: ADAMS HOMES
5373 San Benedetto Place, Fort Pierce, FL 34951
Cooling Equipment
Design Conditions
design DB:
90.4 OF
Sensible gain:
20509
Btuh
Outdoor design WB:
77.4 OF
Latent gain:
3648
Btuh
Indoor design DB:
75.0 OF
Total gain:
24157
Btuh
Indoor RH:
50%
Estimated airflow:
947
cfm
Manufacturer's Performance Data at Actual Design Conditions
Equipmenttype: SpIitASHP
Manufacturer:
Carrier
Model: 25HBC530AP03+FX4DNF031 L00
Actual airflow:
947
cfm
Sensible capacity:
21358
Btuh
104% of load
Latent capacity:
5637
Btuh
155% of load
Total capacity:
26995
Btuh
112%of load SHR: 79%
Heating Equipment
Design Conditions
design DB: 41.0 OF Heat loss: 22776 Btuh
Indoor design DB: 70.0 OF
Manufacturer's Performance Data at Actual Design Conditions
Equipment type: SpIitASHP
Manufacturer: Carrier Model: 25HBC530AP03+FX4DNF031 L00
Actual airflow: 947 cfm
Output capacity: 26672 Btuh 117% of load
Supplemental heat required: 0 Btuh
Backup equipment type: Elec strip
Manufacturer: Model:
Actual airflow: 947 cfm
Output capacity: 5.9 kW 89%ofload Temp. rise: 19 OF
Meets all requirements ofACCA Manual S.
Entering coil DB: 76.4°F
Entering coil W B: 63.2 cF
Entering coil DB: 69.5°F
Capacity balance: 36 OF
Economic balance: -99 OF
At. * wrightsoft- 2021-Jarr1412:18:16
...... — Right-Sprite®Uruversal202121.0.02RSU23828 Pagel
aterstone1512AGL\LotlgBlk5Waterstonel512AGL.rp Calc=MJ8 Hoisefaces:S
Component Constructions Job: Lot 19 Block 5 Waterston...
wrightsoft® Date:
Entire House By: FLETCH
DEL -AIR .HEATING & AIR CONDITIONING
531 CODISCO WAY, SANFORD, FL 32771 Phone:407-333-2665 Fax: 407-333-3853 Web: W W W.DEL-AIR.COM
• • •
For: ADAMS HOMES
5373 San Benedetto Place, Fort Pierce, FL 34951
Design
Conditions
Location:
Indoor:
Heating
Cooling
St Lucie Co Intl, FL, US
Indoor temperature (OF)
70
75
Elevation: 26 ft
Design TD (OF)
29
15
Latitude: 28 °N
Relative humidity (%)
30
50
Outdoor: Heating
Cooling
Moisture difference (gr/lb)
2.4
56.9
Dry bulb (OF) 41
90
Infiltration:
Daily range (OF) -
15 (L
) Method
Simplified
Wet bulb (OF) -
77
Construction quality
Average
Wind speed (mph) 15.0
7.5
Fireplaces
0
Construction descriptions Or Area U-value Insul R Htg HTM Loss Clg HTM Gain
ft� Btuh/ftz F ftz`F/Btuh BtuhW Btuh Bluh/ft� Btuh
Walls
Blk wall, stucco ext, r-4 ext bd ins, 8" thk, 1/2" gypsum board int fnsh
Partitions
12C-Osw. Frm wall, 1/2" gyp.bd ext, r-13 cav ins, 1/2" gypsum board int
fnsh, 2'SK4" wood frm, 16" o.c. stud
n
267
0.201
4.1
5.83
1555
4.06
1083
e
434
0.201
4.1
5.83
2529
4.06
1762
se
8
0.201
4.1
5.83
46
4.06
32
s
112
0.201
4.1
5.83
650
4.06
453
sw
8
0.201
4.1
5.83
46
4.06
32
w
323
0.201
4.1
5.83
1884
4.06
1313
all
1151
0.201
4.1
5.83
6711
4.06
4675
278
0.091
13.0
2.64
734
1.31
364
Windows
2A-2ov: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8" n 30
thk; NFRC rated'(SHGC=0.23); 50% drapes, medium; 8.33 ft overhang (5
ft window ht, 0.83 ft sep.); 6.67 ft head ht
2A-2ov: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8" n 23
thk; NFRC rated (SHGC=0.23); 50% drapes, medium; 1.3 ft overhang
(5.25 ft window ht, 0.83 ft sep.); 6.67 ft head ht
2A-2ov: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8" n 33
thk; NFRC rated (SHGC=0.23); 50% drapes, medium; 1.3 ft overhang
(5.3 ft window ht, 0.83 ft sep.); 6.67 ft head ht
2A-2ov: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8"
thk; NFRC rated (SHGC=0.23); 50% drapes, medium; 1.3 ft overhang
" (3.17 ft window ht, 1 ft sep.); 6.67 ft head ht
2A-2ov: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8"
thk; NFRC rated (SHGC=0.23); 50% drapes, medium; 1.3 ft overhang
(5.3 ft window ht, 1 ft sep.); 6.67 ft head ht
2A-2ov: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8"
thk; NFRC rated (SHGC=0.21); 50% drapes, medium; 1.3 ft overhang (5
ft window ht, 1 ft sep.); 6.67 ft head ht
e 10
0.330 0
0.330 0
0.330 0
0.330 0
9.57 287 8.52
9.57 222 8.52
9.57 313 8.52
9.57 93 22.8
256
198
279
223
e
16
0.330
0
9.57
156
23.0
376
se
10
0.330
0
9.57
96
15.0
150
s
15
0.330
0
9.57
144
8.22
123
sw
10
0.330
0
9.57
96
15.0
150
all
35
0.330
0
9.57
335
12.1
423
Wrightsci t- 2021-Jarr1412:18:16
ate* �• �. •�• -.,� •m Right-Slrite® Uriversal 2021 21.0.02 RSU23828 Page 1
aterstone1512AGL1Lot19BIk5Waterstore1512AGL.rLp Calc=MJ8 Hosefaoes: S
2B-2fv: 2 glazing, clr low-e outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1 /8" s
3
0.330
0
9.57
29
9.72
29
thk; NFRC rated (SHGC=0.31); 50% drapes, medium; 7.33 ft overhang (1
ft window ht, 0.75 ft sep.); 6.67 ft head ht
10C-v: 2 glazing, clr low a outr, air gas, vnl frm mat, clr innr, 1/4" gap, 1/8" w
18
0.550
0
16.0
285
16.2
289
thk; NFRC rated (SHGC=0.70); 13 ft overhang (6.7 ft window ht, 1.3 ft
sep.); 6.67 ft head ht
2A-2ov: 2 glazing, clr outr, air gas, vnl frm mat, clr low a innr, 1/4" gap, 1 /8" w
7
0.330
0
9.57
66
22.1
151
thk; NFRC rated (SHGC=0.23); 50% drapes, medium; 1.3 ft overhang
(3.17 ft window ht, 0.83 ft sep.); 6.67 ft head ht
F
Doors
11JO: Door, mtl fbrgl type s
20
0.600
6.3
17.4
350
17.6
353
11 DO: Door, wrl sc type n
18
0.390
0
11.3
202
11.4
204
Ceilings
166-30ad: Attic ceiling, asphalt shingles roof mat, r-30 cell ins, 1 /2"
1580
0.032
30.0
0.93
1467
1.69
2670
gypsum board int fnsh
Floors
22A-tpl: Bg floor, light dry soil, on grade depth
192
0.989
0
28.7
5519
0
0
ti � Wrightsoft- 2021-Jan-1412:18:16
JCCA •�" • •N• Right-SUte®Uriversal202121.0.02RSU23828 Paget
aterstone1512AGL\Lot19Blk5Waterstone1512AGL.np Calc=MJ8 Hosefaces: S
Project Summary
Job: Lot 19 Block 5 Waterston...
wrightsoft®
o Entire House
Date:
By: FLETCH
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCOWAY,,SANFORD,FL32771 Phone:407-333-2665 Fax:407-333-3853 Web:WWW.DEL-AIRCOM
Project
• •
For: ADAMS HOMES
5373 San Benedetto Place, Fort Pierce, FL 34951
Notes: RVSD 8-17-15 JA
L. S. 1-14-21 VWK
Design Information
Weather: St Lucie Co Intl, FL, US
Winter Design Conditions
Summer Design Conditions
Outside db 41 OF
Outside db
90
OF
Inside db 70 °F
Inside db
75
OF
Design TD 29 OF
Design TD
15
OF
Daily range
L
Relative humidity
50
%
Moisture difference
57
gr/lb
Heating Summary
Sensible Cooling Equipment Load Sizing
Structure 19507 Btuh
Structure
15972
Btuh
Ducts 3269 Btuh
Ducts
4537
Btuh
Central vent (0 cfm) 0 Btuh
Central vent (0 cfm)
0
Btuh
none
(none)
Humidification 0 Btuh
Blower
0
Btuh
Piping 0 Btuh
Equipment load 22776 Btuh
Use manufacturer's data
y
Rate/swing multiplier
Equipment
1.00
Infiltration
sensible load
20509
Btuh
Method Simplified
Latent Cooling Equipment
Load Sizing
Construction quality Average
Fireplaces 0
Structure
2548
Btuh
Ducts
1100
Btuh
Central vent (0 cfm)
0
Btuh
Heatingg Coolin
Area
(none)
(ft2) 1512 1515
Equipment latent load
3648
Btuh
Volume (ft3) 13571 13571
Air changes/hour 0.38 0.20
Equipment Total Load (Sen+Lat)
24157
Btuh
Equiv. AVF (cfm) 86 45
Req. total capacity at 0.75 SHR
2.3
ton
Heating Equipment Summary
Cooling Equipment Summary
Make Carrier
Make Carrier
Trade CARRIER
Trade CARRIER
Model 25HBC530AP03
Cond 25HBC530AP03
AHRI ref 204840289
Coil FX4DNF031 L00
AHRI ref 204840289
Efficiency 8.5 HSPF
Efficiency 12.5 EER,15 SEER
Heating Input
Sensible cooling
21300
Btuh
Heating output 28200 Btuh C) 47°F
Latent cooling
7100
Btuh
Temperature rise 27 OF
Total cooling
28400
Btuh
Actual airflow 947 cfm
Actual airflow
947
cfm
Air flow factor 0.042 cfm/Btuh
Air flow factor
0:046
cfm/Btuh
Static pressure 0.40 in H2O
Static pressure
0.40
in H2O
Space thermostat
Load sensible heat ratio
0.85
Capacity balance point = 36 OF
Backup:
Input = 6 kW, Output = 20230 Btuh,100 AFUE
Calculations approved byACCA to meet all requirements of Manual J 8th Ed.
wr1ghtso1Ft- 2021-Jan-14 12:18:16
ICE ^M °° ° - Right-Srrite®Uriversal202121.0.02 RSU23828 Page 1
aterstone1512AGL1Lot18BMWaterstore1512AGL.nQ Calc=MJB House faces: S
-140- wrightsoft, Right-JO Worksheet
Entire House
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCOWAY,,SANFORD,FL32771 Phone:407-333-2665 Fax:407-333-3853 Web:WWW.DEL-AIR.COM
Job: Lot 19 Block 5 Waterston 15...
Date:
By: FLETCH
1
Room name
Entire House
WIC
2
Exposed wall
192.4 It
8.0 ft
3
Room height
9.0 ft
8.3 ft heaV000l
4
5
Room dimensions
Room area
1516.0 ft2
1.0 x 41.8 ft
41.8 ft2
Ty
Construction
U-value
Or
HTM
Area (ft2)
Load
Area 02)
Load
number
(Btuh/ft2-fl
(Btuhfit2)
or perimeter (ft)
(13 h)
or perimeter (ft)
(Btuh)
Heat
Cool
Gross
N/P/S
Heat
Cool
Gross
N/P/S
Heat
Cool
6
11
�VLBlk
131kwall oext
stucc
2A-26v
2A-2ov
wall, stucoo ext
0.201
0,330
0.330
_0.330
0.201
n
n
n
n_
a
583
9.57
9 57.
_9 57
5.83
406
8.52
8 52
._-. 8 52
4.06
353
30
23
. 33
460
267
0
0
- _ __. 0
434
1555
287
222
_e 313
2529
1083
256
198
_: _ .----279
1762
- 0
` 0
0
0
0
0
0
0
0
'0
0
0;
0
2A-2ov
0.330
a
9.57
22.83
10
0
93
223
0
0
0
0
4_
Vil
2A-2ovT�
Blkwall, sluoco ext-
0330
0201
e
se' :
- 957,
5 83
22_98
4.06
16
0
156
46
376
32
0
--
0
0
0
0
0
_ 0
0
18
' 8
2A-2ov.___., ___.-
Blk wall, sluoco ext
_______0.330
0.201
-se-
s
____9.57"
5.83
__14.96
4.06
_-.._..'_10
150
_.._ .`- 2
�_.___96
.._150
453
___,._.__-0
3
_ .- 0
3
__'_-0.
17
12
112
650
--
VIJ
qR
C
F_
2A-2ov
213-2tv
11,Jo
Blk wall stucbo ext
Blk wall, stu000 ext
10C-v
2A-2ov
12C Osw w
16B-30ad _
0.330
0.330
0.600
0201
0.201
0.550
0.330
0.091
0.032
s
s
s
snr
suY_
w
w
w
9.57
9.57
17.40
5 83'
.. 9 57:
5.83
15.95
9.57
2 64'296
_.�. 1131,
0.93
8.22
9.72
17.58
4.06,
14 96
4.06
16.20
22.06
_ 11.43
1.69
15
3
20
18
_. �,'10
348
18
7
_ 18
1580
15
3
20
W 8
.> _ ....._2
323
18
1
1278
. r 18
1580
144
29
350
46
1884
285
66
m734
_ 1, 202
1467
5519
_s:;v_x7-7
123
29
353
1313
289
151
` : 364
2670
0
0
0
0
0
0
64
43
0
0
0
0
0
0
64
43
0
0
0
0
0
0
4_ 169
_ _ _
40
0
0
0
0
0
0
84:
73
7r
61
c) AED excursion
196
-8
Envelope loss/gain
16768
10686
455
160
12
a) Infiltration
2739
766
6
2
b) Room ventilation
0
0
0
0
13
Internal gains: Occupants@ 230
4
920
0
0
Appliances/other
3600
0
Subtotal (lines 6 to 13)
19507
15972
461
162
Less external load
0
0
0
0
14
Less transfer
Redistribution
Subtotal
0
0
19507
0
0
15972
0
0
461
0
0
162
15
Duct loads
17%
28 %
3269
4537
17°/
28%1
77
46
Total room load
Air required (dm)
22776
9471
20509
947
538
22
208
10
Calculations approved bvACCA to meet all requirements of Manual J 8th Ed.
C
-�- wrigt�tsoft- 2021-Jarr1412:18:16
�"�A 5 Right-Sute®Uruversal 2021 21.0.02 RSU23828 Page 1
aterstone1512AGL1Lot19Blk5Waterstone1512AGL.nQ Calc=W8 Housefaces: S
-- wrightsoft9 Right-JO Worksheet
Entire House
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCO WAY, SANFORD, FL 32771 Phone:407-333-2665 Fax:407-333-3853 Web:WWW.DEL-AIR.COM'
Job: Lot 19 Block 5 Waterston 15...
Date:
By: FLETCH
1
Room name
MBATH
WC
2
Exposed wall
17.5 It
4.0 It
3
Room height
8.7 ft heaV000l
9.0 It heaV000l
4
Room dimensions
1.0 x 136.0 ft
1.0 x 20.3 It
5
Room area
136.0 ft2
20.3 ft2
Ty
Construction
U-value
Or
HTM
Area (ft2)
Load
Area (ft2)
Load
number
(Btuh4t2)
(Btuh4t2)
or perimeter (ft)
(Btuh)
or perimeter (ft)
(Btuh)
Heat
Cool
Gross
N/P/S
Heat
Cool
Gross
N/P/S
Heat
Cool
6
__
Blk wall stucco ext
2A-2ov
0 201
0336
n
n
5 83'
957.
4 06
852
0
0
0
0
0
0
0
0
--
0
0
0
0
a
0
0'
ffi°
2A-2ov
0 330
n
9.5
8 52
0
0
0
0
0,
0
0
a 0
$,4-2ov.�� w'
0330,r1
11
wall, stucco ext
0.201
a
5.83
4.06
0
0
0
0
0
0
0
0
VLBlk
2A-2ov
0.330
a
9.57
22.83
0
0
0
0
0
0
0
0
2A-2ov
0.330
a
9.57
22.98
0
0
0
0
0
0
0
0
V)!
_81k wall stuaq ext
0:201
se
..
5�83
4 06
0
0
F U
U
Q
r.0
V 0
Q.
L -G
2A-2ov. _,
_0.330
se..
.9.57a
�14.96
a
0
u
. �6
L' c . 0
M
a _0
0:
Blk wall, stucco ext
0.201
s
5.83
4.06
6
6
32
22
0
0
0
0
2A-2ov
0.330
s
9.57
8.22
0
0
0
0
0
0
0
0
213-2tv
0.330
s
9.57
9.72
0
0
0
0
0
0
0
0
11J0
0.600
s
17.40
17.58
0
0
0
0
0.
0
0
0
_
Blk wall stucco exi
0201
sw
5 83
4 06A
0
0
017
70
0
.Ua
" a32
Blk wall, stucco ext�
0.201
w
5.83
4.06
96
89
520
362
32
187
130
10C-v
0.550
w
15.95
16.20
0
0
0
0
0
0
0
0
2A-2ov
0.330
w
9.57
22.06
7
1
66
151
0
0
0
0
RR
12C Osw
i 0 091
2 64131
44
, + 44
116
58
0
0
<
C
166-30ad
0.032
0.93
1.69
147
n 147
136
248
.: 22
22
21
38
28:68
O;QQ.
ti1-8
20
4
116
:O;
__
_ n .:136
_ s502
__ _ .0
a
x5.....a...�......................�i,
, ¢
x
.„4 M
S,r...etL,f...i%L'r,e
........ },:-'�
.a..:
z....-..,.a..
3.h.s,..u.a
7
._._..-,�..z._.w..._..,....�......,....xs,t
��.___, _
........,.....
.��,_, ..F...,...._,.c.tik..
.�a.. �,-.,.�...
SMx
=,«
.�...�.:.�..
s....�.»-, .,�
.me....,..µ ,..d
.,r.,....�
"-
_>..-.:..as.-
.n.,�.s....r.......r:-�.�.._.._
s>.,^«ev........,
_,a
......,..z_
�.....,....
.....w,s.�..
a „a.nw...E
,...,,,.... y
.w .a: .,
...,.,.....ry
,-..�E:..ja,....£�
srt`�i,.�....c.v
_.............»
...,-,z,_
,w..a,�.,a_....�..,.>_..a-„_
,_........;.�.kz_�
..
....v_.....a.
.,max.
.....-.L... u,.,,�.a:.
..v,..�„d.=.x.,r.. x.....,
.,.��c,..._...,� s.
n`wia._.._..,.....�,.�,._.,..-k..'y.�.,.��...a..
`�iz..........,.�:.�
,..,.�.,...a.,.,.,..
...,_.,..-{.,.'e..w....w._-.w.,..+.,...z.
.,..._�...,.«.
,..
...,c„..
.....�....�-a........... ....
_._....
w.,
A+.m,.,FF
_
6
c) AED excursion
53
-8
Envelope loss(gain
1372
894
322
159
12
a) Infiltration
207
58
65
18
b) Room ventilation
0
0
0
0
13
Internal gains: Occupants@ 230
0
0
0
0
Appliances/other
0
0
Subtotal (lines 6 to 13)
1578
952
387
178
Less external load
0
0
0
0
Less transfer
0
0
0
0
Redistribution
0
0
0
0
14
Subtotal
1578
952
387
178
15
Dud loads
171/6
28%
264
270
17%
28%1
65
50
Total room load
1843
1223
452
228
Air required (cfm)
77
56
191
11
Calculations approved byACCAto meet all requirements of Manual J 8th Ed.
- c -*- wrightsoft- 2021-Jarr1412:18:16
Right-Sdte®Udversal 2021 21.0.02 RSU23828 Page 2
aterstore1512AGL\Lot19BIk5Waterstore1512AGL.r p Calc=MJ8 House faces: S
Job: Lot 19 Block 5 Waterston 15...
Date:
1- wrightsoft' Right-JO Worksheet
Entire House
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCO WAY SANFORD, FL 32771 Phone:407-333-2665 Fax:407-333-3853 Web: W W W.DEL-AIR.COM
By: FLETCH
1
Room name
MBR
LAU
Exposed
35.5 ft
6.0 ft
3
height
8 6 ft heaYbool
8.0 It heaV000l
4
Room dimensions
13.5 x 16.5 ft
1.0 x 56.0 It
5
Room area
222.8 ftz
56.0 ftz
Ty
Construction
U-value
Or
HTM
Area (ftz)
Load
Area (ftz)
Load
number
(Btuh/ftz-fl
(Btuh/ftz)
or perimeter (ft)
(Btuh)
or perimeter (ft)
(Btuh)
Heat
Cool
Gross
N/P/S
Heat
Cool
Gross
N/P/S
Heat
Cool
6
Blk:wall sh�000a#�
2A-2ov
0201
0 330
n
n
' 583;
9 57,
t 406
8 52
ii6
0}
84
0
488
0
340
0
0
0
0
0
a, 0
0
1 0
0'
2A-2ov
0 330
n
9 57
8 52
P 0
0
g 0
0
0
0
0
0
8 52
0..w313
,r
279
0
11
Blk wall, stucco ext
_. 0.201
a
5.83
4.06
,e_..-33_.
44
44
256
.�
179
L*w ,_F
0
0
0
0
�G
2A-2ov
0.330
a
9.57
22.83
0
0
0
0
0
0
0
0
L -C
2A-2ov
0.330
e
9.57
22.98
0
0
0
0
0
0
0
0
Vf/
Blk wall shi000 e#
0201
se''
5 83;
4.06
0
"0
= °"0
0
0
0
p
0
0.330
se
14.9fi
"0
_ 0
_ 0
,_ 0
-0
0:
Blk wall, stucco e#
0.201
s
5.83
4.06
0
0
0
0
0
0
0
0
2A-2ov
0.330
s
9.57
8.22
0
0
0
0
0
0
0
0
213-21v
0.330
s
9.57
9.72
0
0
0
0
0
0
0
0
11 JO
0.600
s
17.40
17.58
0
0
0
0
0
0
0
0
Blk wall stucpo e#
O'201
sw
5 83
4 06
0
6
0
xrr7
tl 4
0
^ � 0
0
w~ F0
N� 0,
^ µ
y/
Blk vdi, stucco e#
0201
w
5.83,
4.06
132
132
769
536
0
0
0
10C-v
0.550
w
15.95
16.20
0
0
0
0
0
0
0
0
2A-2ov
0.330
w
9.57
22.06
0
0
0
0
0
0
0
0
Fq�
12C Osw a
0.091�
264'
131,
`��_���;''48
127
63
�D
JJ;DO
0:390�143.
U 0
' 0,
C
1613-30ad
0.032
0.93
1.69
238
238
2-21
402
56
56
52
95
. x
._.+-«..�.......e....�..,.�a.�.....x,..
«..,.«..,.....,».
m...i..v..
.,wvw_,
... A.,..�...
-.r...a.......,.:..4
.,..} .. ....�
as_.... .e._.c
+...a.. .._«:...
w�..--•-....,.....
..n...v..F.h.'_«.
,i...w-.„..c.
.w...-..da..
2:.:.......�
�»..
v..�f �
�
�`, ry�i
_...... ..,. x.,.._e.........er...ra
9. =...r L..
....
�A.�.......
.YLM..c..w
,..._..vd.z,a23...,
✓nT
.., .+.
w_.a.
ua.1 sa..
a'�
.u.�...a..,..w..._.,.,.sL.,..f,..�u....'.:
, ...._.e............
:t Y^TM"
.m...,...�,... �^..'..�i
_ ..xu�.
..»....<..�.J..e
u...,.wP..ww.�.-
.#".�«...�a->.....0
..wS.:^»w .a,. �.
Q.s..n.,..._..t...�...
..-.-u
.wu.......-w..ws,
....._..,..._ �swr
-
_
z
»-...
'w...v...=..........
r+..._.i,..mum..
,,.,..»v..
.�.....
'i.....x.......-.e
.....r�.a
.,r..&+�M..n.Y_ w.
r..�z....s.
,h k�.rd...sS..�.
n� E...e
x v.... �<Via.
m.=..1.a=,.:..._..vu,
�
�,..A.a�s�
_»..,,._.. _
....,.. ....�.-.s_........v...._%--
_..:..»..,.....,.z
,.
y... _
_>
_.�..wh..�...s_...
...ay. w.._.
.»_-.,_+�x.,.....t....a..i_
.............
..ss nw
�,._...r.
... ,,..�.:�d......:.°=,_
't' ter...
m....na,
.�.., ...i.._.._._«-.-......�.
.�.Y.-+ ...u,.+_
W.=v.
aa.aa1......,
uu+,,..d+...
«...u...„.......
x .�.......s
..-.v.n,.a_.v,,�,.�«
a.e»....,.,..,.4,.u...,.....:..-,.'......-,...
.-....
-.,...,...-..wk,-....L+_..
..-...>..,..
a,..,..,..r-
...-..a..L
. .e'e,.... h,.
.,.fe.�......,kv,«.
MI.
..z....X...i ..
, .....,.,..ate..
..�abK.s:..:.s......
-isa,..,., 5.....
SU=
=...,a....�..sc,:'Ri
..aF
.....,....� _.,.......,..i
.gym....._...._.
_
a.-.,..,, _
may.._,.,,.
s.-a.. aas.
.,..,....,.
,..„........�. ..
..M.,,.w. ,...,ab......
..ti
.�...,.2A.e.....'<,.,. ._
dw�>L..
.�... ...
e.w...<..£a,
,.Ywv.X .2,Y.....,.
..-e� ;,....-.a
6
c) AED excursion
-124
-34
Envelope losstgain
3065
1611
351
123
12
a) Infiltration
595
166
0
0
b) Room ventilation
0.
0
0
0
13
Internal gains: Occupants@ 230
1
230
0
0
Appliances/other
600
600
Subtotal (lines 6 to 13)
3660
2607
351
723
Less external load
0
0
0
0
Less transfer
0
0
0
0
Redistribution
0
0
0
0
14
Subtotal
3660
2607
351
723
15
Dualoads
17%
28%
613
741
17%
28%
59
205
Total room load
4273
3348
409
929
Air required (dm)
178
155
17
43
Calculations approved byACCAto meet all requirements of Manual J 8th Ed.
-rFF =1gfttso14t_ 2021-Jan 1412:18:16
Right-Sdte®Uruversal 2021 21.0.02 RSU23828 Page 3
...aterstone1512AGLLot1981k5Waterstone1512AGL.nQ Calc=W8 House faces: S
Job: Lot 19 Block 5 Waterston 15...
Date:
- +- wrightsoft9 Right-M Worksheet
Entire House
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCOWAY,,SANFORD,FL32771 Phone:407-333-2665 Fax:407-333-3853 Web:WWW.DEL-AIR.COM
By: FLETCH
1
Room name
BR3
BATH2
2
Exposed wall
31.9 ft
6.0 ft
3
Room height
8.0 8 heaUmol
8.9 ft heaUmol
4
5
Room dimensions
Room area
1.0 x 162.0 It
162.0 ft2
9.5 x 6.0 ft
57.0 112
Ty
Construction
U-value
Or
HTM
Area (ft2)
Load
Area (ft2)
Load
number
(Btuh/ftzg
(Btuh/12)
or perimeter (ft)
(Btuh)
or perimeter (ft)
(Btuh)
Heat
Cool
Gross
N/P/S
Heat
Cool
Gross
N/P/S
Heat
Cool
6
Blkwal1 stucco ext
2A2ov
2A-2ov
0. 201
0330
0 330
n
n
n
5 83
957
9 57
4 06
852
8 52
" 0
O
0
0
s 0
0
0
0
0
0
0
0
U
0
0
0
0
0
0
0
0
0`
0
A:
11
n
it
Blk wall, stucco ext
n. .._,_033Q
0.201
_n_
a
.� 9 57.
5.83
_ 8.52
4.06
. _ _ _0
108
, s.. _ 20
108
.. _ ._ Q
630
._._ '_0
439
48
48
280
0
195
YVu
t-C
2A-2ov
2A-2ov_
Blkwall,stu000ext �_
2A:2ov.
Blk wall, stu000 ext
0.330
0.330
-0201
_-0.330
0.201
a
a
se
.._se_
s
9.57
9.57
5:83'
..-.-.957
5.83
22.83
22.98
4:06
_14.96
4.06
0
0
0
0
0
0
0
0
_ 32
_.-160
215
0
0
p
__ _0
8
0
0
. --' .- _.A
8
0
0
0
0
_ _,_.._O.
34
18
_ 10
68
8
-
53
46
309
._.,._,__20
49
1�/
V�-�--(GG'
R
G
2A-2ov
28-21v
11 JO
Blk wall stucco ext
2A,2oy . _
Blk wall, stu000 ext-
10C-v
2A-2ov
12C Osw .ry
16B-30ad
0.330
0.330
0.600
� 0201
_ 0,330
_ 0.201
0.550
0.330
0 091
...__,00,0
0.032
s
s
s
sw
_. sw;"
w
w
w
9.57
9.57
17.40
-` 5 83
,._ _ 9 57
5.83
15.95
ry m 9.57
2 64
0.93
8.22
9.72
17.58
4 06
_. 14 96
4.06
16.20
22.06
i 31.
1.69
15
0
0
18
_...1.0
44
0
0
0
_ 162
15
0
0
8
,>, __M._2
44
0
0
� 0
_ 162
32
144
0
0
46
. ., 96
256
0
0
0
. 150
915
' 123
0
0
32
s ,_ ,.1,50
179
0
0
_ 0
274
0
0
0
µ 0
. _ .5
0
0
0
r ._3
0
62
0
0
0
_ _ �, 0
0
0
0
0
_: 0
62
0
0
0
u_..... ._, U.
0
0
0
0
..: _--.0-
58
0
0
0
m .., Q.
0
0
0
' .r.0
_•_ 0
105
T..
a mi,
7 7,
_ .
_.._. .__
.._..,_.,._..,....._...=,...s..,..._....,
......,-
_.........
...:5.,i.'_.'
._..,._,. _..
.»s_F.E_s..x
.�»�...e .
,4,.5'>s.s_
......r..<.
a_..-,_.....
,.__.,....
6
c) AED excursion
-92
-17
Envelope losssIgain
2688
1500
558
317
12
a) Infiltration
520
145
115
32
b) Room ventilation
0
0
0
0
13
Internal gains: Occupants @ 230
0
0
0
0
Applianoesrother
300
0
Subtotal (lines 6 to 13)
3208
1946
673
349
Less external load
0
0
0
0
14
Lesstransfer
Redistribution
Subtotal
0
0
3208
0
0
1946
0
0
673
0
0
349
15
Ductloads
17%
280/6
538
553
170%
28%1
113
99
Total room load
Air required (cm)
3746
156
2499
115
786
33
449
21
Calculations approved bvACCAto meet all reauirements of Manual J 8th Ed.
-ri &- 2021 -Jan-1 4 12:18:16
Right-SuteOUniversal 202121.0.02RSU23828 Page
ACCK
aterstone1512AGLtLotl9Blk5Waterstonel512AGL.nQ Calc=MJ8 Housefaces: S
Job: Lot 19 Block 5 Waterston 15...
Date:
-- wrightsofV Right-JO Worksheet
Entire House
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCO WAY, SANFORD, FL 32771 Phone:407-333-2665 Fax:407-333-3853 Web:WWW.DEL-AIR.COM
By: FLETCH
1
Room name
BR2
Krr
2
Exposed wall
11.0 ft
10.0 ft
3
Room height
8.6 ft heaticool
8.7 ft heaV000l
4
Room dimensions
14.0 x 11.0 ft
1.0 x 120.8 ft
5
Room area
154.0 ft2
120.8 ft2
Ty
Construction
U-value
Or
HTM
Area (ft2)
Load
Area (ft2)
Load
number
(BtuhHt2-T)
(13tuhHt2)
or perimeter (ft)
(Btuh)
or perimeter (ft)
(Btuh)
Heat
Cool
Gross
N/P/S
Heat
Cool
Gross
N/P/S
Heat
Cool
6
w n
Blk wall stucco ext
2A2ou
0 201
0330
n
n
5 83
957:.
4 06
852
D
_0�
s 0
0�
' 0
` 0
0
0
0
0.
0
0
0
2A-2ov
0330
n
957
852
0'
0-
57
2, 8
J9
d 0
_
_ A
0
„ 0
.0
"
0
0'
11
Blk wall, stucco ext
0:201
a
5.83
4.06
88
72
418
291
80
70
4o9
285
2A-2ov
0.330
a
9.57
22.83
0
0
0
0
10
0
93
223
2A-2ov
0.330
a
9.57
22.98
16
0
156
376
0
0
0
0
BII<;wall stucco ext
020i
se
5 83;Y
4 06
x ^A
0
0
07
77,+ 0,
0
0
�: 4
2A 2ov
A.386
_se
9.5Z
--, 14.96
0
� .0
�0
0
a e 0
_ a 0
.. �0
_ w ' °0.
Blk wall, stucco ext
0.201
s
5.83
4.06
0
0
0
0
0
0
0
0
2A-2ov
0.330
s
9.57
8.22
0
0
0
0
0
0
0
0
2B-2fv
0.330
s
9.57
9.72
0
0
0
0
0
0
0
0
11.J0
0.600
s
17.40
17.58
0
0
0
0
0
0
0
0
Blkwall sWocoext
0201
sw
583
406
0
0
0
0
4 0
0
0
N 0
oVtJ
Blk wall, stucco ext
0.201
w
5.63
4.06
0
0
0
0
0
0
0
0
10C-v
0.550
w
15.95
16.20
0
0
0
0
0
0
0
0
2A=2ov
0.330
w
9.57
22.06
0
0
0
0
0
0
0
0
R
12G Osw "�
00917
264,
77X31_
6
:77M 0
M_Q
1160 e _
0.390
, '. 9
" AO
e L..
y 0
~ �., U
w n0
».e
C
168-30ad
0.032
0.93
1.69
164
164
152
_,"�
277
130
.
130
_ .
121
219
x
,�
r
t
.._.�
_.......__.,-..�...�....�.. :,... m
....,,_�.....,
w. .
Y.r._... _.e...
--
-....,.ti,.,.e.
k'..t....,...�...�x.s,.,.>..>
,...,,_,-e
...,,... -...�, .... ..,,._n«z
.,-........-.+.6:..
...
a._ _
n...95<
,...
�.R,....�' .w:`.E=.o
112_....
a.».
........,._.,_......... .....a...,__.,..,.....
...c-......w.....,
..,
.a..,.«s.
u,.�.,_
m..>.�sM.t`.�;.rw
-�,...-.-
:i�z.,m»... ...�
wts.,.x�„w`",.
�k.,.-.,<.....�
.,.
_»_w
., s.
..._.rw.a
.,:-..,U�-..._,�.._. .... '
-„...�..,..a�.w:.,..
,:..
..__......�...5«
,_..?.3.. .......
........aw ",.
,n,..,.,.,;zu:,,.
sx.
�.�s�•s,m..,..
�,. t
a a.,.a..T
�.a...&...._.
�...rs.....,.«.....,..a:t
..=..'a ,...
«_,:v,..�Ma.-..,..._�..,. H.,.s. -
..,,....,,.,,s..,
,._
.aa.,ma.»,.
_..s,,_.
... <.<, -..,
a,.�o..._
...8,...�. «..i..._.._
x.�.�c..
._,.......,__.:%:
...•s._,k_x
..�.,.,....c_.. �
_.izr,. awe...:x
�
a
e�_
.�..........�....��_e...o.._......-A.w..
_..�.�,_ _.E_ ..
.�s..,.a
,....�.....�
..._.,....as'.:..�.
�
�..U.�
__.az:.�.v..�..,a.
_<�.....,�,.
.�...�.w a,.,
._.x.w.� �
..�......,�.d
.,_....._
.�'�.�: j1,7
v..�....-_.
.......�a.,.2..�s..w�.Y.n.v....._t
..�.r..n ....._„
X:.
ri=
....n. o-, >
Z_v.s- s_x
=
..-.,Y•`.1.-.....:�
._i...,e
»a'SJ .. w......C.'=;. ..............
...:.,......,..+iw"w
_......a,....-.v.,
a...w..._
«s.L.. u.,.._
v.w...ln "::. e.
�u
o..a r..n
e.........,.
....-�.a„uf.
u.. ....T...
M.ZEm.:::1:1
-.L.w.
,..tu .x..,,,.a+.w.�...w....,r.....
.........e..
.-
-mr.Y
.,
v..,a.
.,...v .r m
w�...-.�e'�..
a�._�arvA
a
rso-R.3 ..
w.un....wa.....a•
_._._.._.w-
s
..v....rw.«.
.-�,s?�,.s:..d..._..
T
a,:.'v..,,.-..
=
...,.d,.>...
..w-..�
m..�a.,.a&.s..;.P
r.n
..,..h
�...,�i a..,.. �:.0
._.. uu.
.,....i..,..,.....a;.t.
6
c) AED excursion
60
-24
Envelope losstgain
1042
1003
910
704
12
a) Infiltration
179
50
163
46
b) Room ventilation
0
0
0
0
13
Internal gains: Oocupants@ 230
0
0
0
0
Appliances/other
300
1200
Subtotal (lines 6 to 13)
1221
1354
1073
1949
Less external load
0
0
0
0
Lesstransfer
0
0
0
0
Redistribution
0
0
0
0
14
Subtotal
1221
1354
1073
1949
15
Ductloads
179/.
28%
205
384
17%
28%1
180
554
Total room load
1425
1738
1253
2503
Air required (cfm)
59
80
52
116
Calculations approved byACCAto meet all requirements of Manual J 8th Ed.
-4- wrightsoft- 2021-Jarr1412:18:16
Right-Suite®Universal 2021 21.0.02 RSU23828 Page 5
aterstone1512AGLLot19Blk5Waterstore1512AGL.rLp Calc=MJ8 Housefaces: S
wrightsoft° Right-M Worksheet
Entire House
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCO WAY, SANFORD, FL 32771 Phone; 407-333-2665 Fax:407-333-3853 Web: W W W.DEL-AIR.COM
Job: Lot 19 Block 5 Waterston 15...
Date:
By. FLETCH
1
Room name
DIN
GRT/FOY/HALLS
2
Exposed wall
28.0 It
34.5 It
3
Room height
8.8 ft heatbool
10.0 It heaV000l
4
Room dimensions
1.0 x 119.0 ft
1.0 x 426.5 It
5
Room area
119.0 ft2
426.5 ft2
Ty
Construction
U-value
Or
HTM
Area (1112)
Load
Area (ft2)
Load
number
(Btuh/ft2-`-)
(Btuh/ft2)
or perimeter (ft)
(Btuh)
or perimeter (ft)
(Btuh)
Heat
Cool
Gross
N/P/S
Heat
Cool
Gross
N/P/S
Heat
Cool
6
Blf< wall slu000 ext
2A 2ov
0201
0:330
n
n
"5 83
9 57•
4 06
8 52
96
0
; 73
f 0
426
X 0
, ` 297
0
140110
30
0
641
287
447
256
2A 2ov
0330
n
957
85.2
23
0
222
198
933Q'.,n
�_9.57-
�,M8.5�
�...,,.0.,.�..->.'0_....-:
�.O
Q��a.�_0
1 1
Blk wall, stucco ext
2A-2ov
0.201
0.330
a
e
5.83
9.57
4.06
22.83
92
0
92
0
536
0
374
0
0
0
0
0
0
0
0
0
2A-2ov
0.330
e
9.57
22.98
0
0
0
0
0
0
0
0
1Q/
Blk wall, stu000 ext
0201
se
5 83
4 U6
' 0
0
0
0
0
0
0
U
_
242ov _
_ 0.330
a9.57
, _ 14.960
0
XF
Blk wall, stucco ext
2A-2ov
0.201
0.330
s
s
5.83
9.57
4.06
8.22
o
0
0
0
0
0
0
0
65
0
42
0
244
0
170
0
2B-2fv
0.330
s
9.57
9.72
0
0
0
0
3
3
29
29
11JO
0600
s
1740
1758
0
0
0
0
20
20
350
353
lr?!
Blk wall stu000 exf �
0201
sw -
5 83
4-06
0
0
0
r 0
r
6
0
0.
2A=2ov
95TL4:96
.v 300
M
Blk wall, stucco ext
1OC-v
0.201
0.550
w
w
5.83
15.95
4.06
16.20
44
18
26
18
152
285
106
289
0
0
0
0
0
0
0
0
���-------(GG'
2A-2ov
0.330
w
9.57
22.06
0
0
0
0
0
0
0
0
R
12, Osw
0.091
264
0
w 0
0
s 0
" 14Q
i22
160'
0390
. n
20.4,
C
.
166-30ad
.--. .,..,. ....4
0.032
5 .y
-
.W..,
0.93
1.69
129
129
120
219
427
427
396
721
22A WI
U,989
28;68
.,..
Z_.
42713.$5
z '
mW0
z
=
_z _u.._ --"
;w...r
'
,+..,..
........._...�...�....a....,._.:
rw...a A.a.,,., -,,...
r,_..~
...._.a....�_...
,�.._s...
.,.a ,_..,
..�..,_.s,�
....d.a�..
w.r�-.....,.,....
.-. d,..._
._.�,.....s..M_
..,..__.d:�.,
..,.....-.�:nm.
a
x
,w....wK
�.m.ww..<...,.w....e.a.0
,......sue ...... ......
..-,....-,=.
..Av._.,a_,
......,$_._..,
_w.=.,...ss
n.wa.....x.>..
.......»S�i.F-,....,.
a,..��.,.,.,
....«.=
�
..
t,...,._.n.
xz, a........,
...°S .A..>....~.r.
."re_..�._,+.a._...-.tM�
,.P....a?..n
cr.,.....,s-«..,.,
i}..s»M.,...s
.d'..'.. ..a...Y....,
,....w,.eL.Nr.u.
'u
550
-159
6
c) AED
excursion
Envelope loWgain
2545
2033
3461
2180
12
a) Infiltration
473
132
417
117
b) Room ventilation
0
0
0
0
13
Internal gains: Occupants@ 230
1
230
2
460
Appliancesiother
0
600
Subtotal (lines 6 to 13)
3018
2395
3878
3357
Less external load
0
0
0
0
Lesstransfer
0
0
0
0
Redistribution
0
0
0
0
14
Subtotal
3018
2395
3878
3357
15
Duct loads
17%
289/.
506
680
17%
28%
650
954
Total room load
3524
3075
4528
4311
Air required (dm)
147
142
188
199
Calculations approved byACCAto meet all requirements of Manual J 8th Ed.
-
I&K Right-Stite®Universal 2021 21.0.02 RSU23828 2021-Jarr141 Page 6
aterstonel512AGL\L.otl9Blk5Waterstonel512AGL.rLp Calc=MJ8 Housefaces: S g
wlrightsoft® Duct System Summary Job: Lot 19 Block 5 Waterston...
Date:
• Entire House By. RETCH
DEL -AIR HEATING & AIR CONDITIONING
531 CODISCO WAY, SANFORD, FL 32771 Phone:407-333-2665 Fax:407-333-3853 Web: W W W.DEL-AIR.COM
Project Information
For: ADAMS HOMES
5373 San Benedetto Place, Fort Pierce, FL 34951
External static pressure
Pressurelosses
Available static pressure
Supply/ return available pressure
Lowest friction rate
Actual airflow
Total effective length (TEL)
Heating
0.40
in H2O
0.06
in H2O
0.34
in H2O
0.1.70 / 0.170
in H2O
0.359
in/100ft
947
cfm
95 ft
Supply Branch Detail Table
Cooling
0.40 in H2O
0.06 in H2O
0.34 in H2O
0.170 / 0.170 in H2O
0.359 in/100ft
947 cfm
Name
Design
(Btuh)
Htg
(cfm)
Clg
(cfm)
Design
FR
Diam
(in)
H x W
(in)
Duct
Matl
Actual
Ln (ft)
Ftg.Egv
Ln (ft)
Trunk
BATH2
h 786
33
21
0.379
4.0
Ox 0
VIFx
19.7
70.0
BR2
c 1738
59
80
0.408
6.0
Ox 0
VIFx
13.3
70.0
BR3
h 3746
156
115
0.359
7.0
Ox0
VIFx
24.7
70.0
DIN
h 3524
147
142
0.370
7.0
Ox 0
VI Fx
22.0
70.0
GRT/FOYHALLS
c 4311
188
199
0.458
8.0
Ox 0
VIFx
4.3
70.0
KIT
c 2503
52
116
0.406
6.0
Ox 0
VIFx
13.7
70.0
LAU
c 929
17
43
0.456
4.0
Ox 0
VI Fx
4.6
70.0
MBATH
h 1843
77
56
0.430
6.0
Ox 0
VI Fx
9.0
70.0
MBR
h 4273
178
155
0.411
8.0
Ox 0
VIFx
12.8
70.0
we
h 452
19
11
0.417
4.0
Ox 0
VI Fx
11.5
70.0
WIC
h 538
22
10
0.453
4.0
Ox0
VIFx
5.0
70.0
Return Branch Detail Table
Name
Grille
Size (in)
Htg
(cfm)
Clg
(cfm)
TEL
(ft)
Design
FR
Veloc
(fpm)
Diam
(in)
H x W
(in)
Stud/Joist
Opening (in)
Duct
Matl
Trunk
rb2
Ox 0
947
947
0
0
0
0
Ox 0
VIFx
,ti ft * wrightso®
��ek!lB.r6hufaMxa,cnarymry Right-Sute@Urlversa1202121.0.02RSU23828
aterstone1512AGL1Lot19BIk5Waterstone1512AGL.nQ Calc=MJ8 Hoisefaces: S
2021 -Jan-1 4 12:18:17
Page 1
2020 -AIR BARRIER AND INSULATION INSPECTION COMPONENT CRITERIA
1
TABLE 402.4.1.1
AIR BARRIER AND INSULATION INSPECTION COMPONENT CRITERIA
Project Name: Lot 19 Block 5 Waterstone 1512 AGL Builder Name: ADAMS HOMES
Street: 5373 San Benedetto Place Permit Office:
City, State, Zip: Fort Pierce , FL , 34951 Permit Number:
Y
Owner: Jurisdiction: • 661000
w
Design Location: FL, ST_LUCIE_CO_INTL
U
COMPONENT
AIR BARRIER CRITERIA
INSULATION INSTALLATION CRITERIA
General
A continuous air barrier shall be installed in the building envelope.
Air -permeable insulation shall
requirements
The exterior thermal envelope contains a continuous air barrier.
not be used as a sealing material.
Breaks or joints in the air barrier shall be sealed.
Ceiling/attic
The air barrier in any dropped ceiling/soffit shall be aligned with
The insulation in any dropped ceiling/soffit
the insulation and any gaps in the air barrier shall be sealed.
shall be aligned with the air barrier.
Access openings, drop down stairs or knee wall doors to
unconditioned attic spaces shall be sealed.
Walls
The junction of the foundation and sill plate shall be sealed.
Cavities within corners and headers of frame walls
The junction of the top plate and the top of exterior walls shall be
shall be insulated by completely filling the cavity
sealed.
with a material having a thermal resistance of R-3
Knee walls shall be sealed.
per inch minimum.
Exterior thermal envelope insulation for framed
walls shall be installed in substantial contact and
continuous alignment with the air barrier.
Windows, skylights
The space between window/door jambs and framing, and
and doors
skylights and framing shall be sealed.
Rim joists
Rim joists shall include the air barrier.
Rim joists shall be insulated.
Floors
The air barrier shall be installed at any exposed edge of
Floor framing cavity insulation shall be installed to
(including
insulation.
maintain permanent contact with the underside of
above -garage
subfloor decking, or floor framing cavity insulation
and cantilevered
shall be permitted to be in contact with the top side
floors)
of sheathing, or continuous insulation installed on
the underside of floor framing and extends from the
bottom to the top of all perimeter floor framing
members.
Crawl space walls
Exposed earth in unvented crawl spaces shall be covered with
Where provided instead of floor insulation, insulation
a Class I vapor retarder with overlapping joints taped.
shall be permanently attached to the crawlspace walls.
Shafts, penetrations
Duct shafts, utility penetrations, and flue shafts opening to
exterior or unconditioned space shall be sealed.
Batts in narrow cavities shall be cut to fit, or narrow
Narrow cavities
cavities shall be filled by insulation that on
installation readily conforms to the available cavity
spaces.
Garage separation
Air sealing shall be provided between the garage and conditioned spac
as.
Recessed lighting
Recessed light fixtures installed in the building thermal envelope
Recessed light fixtures installed in the building
shall be sealed to the finished surface.
thermal envelope shall be air tight and IC rated.
Plumbing and wiring
Batt insulation shall be cut neatly to fit around wiring
and plumbing in exterior walls, or insulation that on
installation readily conforms to available space shall
extend behind l2apong and wiring.
Shower/tub
The air barrier installed at exterior walls adjacent to showers and
Exterior walls adjacent to showers and tubs shall
on exterior wall
tubs shall separate them from the showers and tubs.
be insulated.
Electrical/phone box or
The air barrier shall be installed behind electrical or communication
exterior walls
boxes or air -sealed boxes shall be installed.
HVAC register boots
HVAC supply and return register boots that penetrate building
thermal envelope shall be sealed to the sub -floor, wall covering or
Concealed
When required to be sealed, concealed fire sprinklers shall only be
sprinklers
sealed in a manner that is recommended by the manufacturer.
Caulking or other adhesive sealants shall not be used to fill voids
between fire sprinkler cover plates and walls or ceffilongs,
a. i l auuniun, mspeauon of log waus snau be in accordance with the provisions of ICC-400.
1/14/2021 12:35 PM EnergyGauge® USA 7.0.00 - FlaRes202O FBC 7th Edition (2020) Compliant Software Page 1 of 1
FORM R405-2020
RESIDENTIAL ENERGY CONSERVATION CODE DOCUMENTATION CHECKLIST
Florida Department of Business and Professional Regulation
Simulated Performance Alternative (Performance) Method
Applications for compliance with the 2020 Florida Building Code, Energy Conservation via the
Residential Simulated Performance Alternative shall include:
❑ This checklist
❑ Form R405-2020 report
❑ Input summary checklist that can be used for field verification (usually four pages/may be greater)
❑ Energy Performance Level (EPL) Display Card (one page)
❑ HVAC system sizing and selection based on ACCA Manual S or per exceptions provided in Section R403.7
❑ Mandatory Requirements (five pages)
Required prior to CO:
❑ Air Barrier and Insulation Inspection Component Criteria checklist (Table R402.4.1.1 - one page)
❑ A completed 2020 Envelope Leakage Test Report (usually one page); exception in R402.4
allows dwelling units of R-2 Occupancies and multiple attached single family dwellings to
comply with Section C402.5
❑ If Form R405 duct leakage type indicates anything other than "default leakage" then a completed
2020 Duct Leakage Test Report - Performance Method (usually one page)
1/14/2021 12:34:13 PM EnergyGaugeg USA 7.0.00 - FlaRes202O FBC 7th Edition (2020) Compliant Software Page 1 of 1
Envelope Leakage Test Report (Blower Door Test)
Residential Prescriptive, Performance or ERI Method Compliance
2020 Florida Building Code, Energy Conservation, 7th Edition
Jurisdiction: 661000
Permit #:
Job Information.
Builder: ADAMS HOMES Community: Lot: NA
Address: 5373 San Benedetto Place
City: Fort Pierce State: FL Zip: 34951
Air Leakage Test Results Passing results must meet either the Performance, Prescriptive, orER1Method
O PRESCRIO-tiVE-METHOD-The building or dwelling unit shall be tested and verified as'having an air leakage rate of,not exceeding air,
'a
changes perhour atpressure,of 0.2 inch -# g (50;P-ascals) in. Climate Zones, 1.,an6l;2;
0 PERFORMANCE or ERI METHOD -The buildin' or 'dwelling unit shall be tested and verified as having an atr=leakage rate of,not exceeding
the selected ACH(50) value, as shown on.Form R405-2020;(Performance) or R40, 2020�(ERI),:section'labeled'as.infiltration,�sub-section ACH50.
ACH(50) specified on Form R405-2020-Energy Calc (Performance) or R4062020 (ERI): 7.000
x 60 : 13608 = Method for calculating building volume:
CFM(50) Building Volume ACH(50) O Retrieved from architectural plans
F-1 PASS Code
0 software calculated
When ACH(50) is less than 3, Mechanical Ventilation installation O Field measured and calculated
must be verified by building department.
R402.4.1.2 Testing. Testing shall be conducted in accordance with ANSI/RESNET/ICC 380 and reported at a pressure of 0.2 inch w.g. (50 Pascals)
Testing shall be conducted by either individuals as defined in Section 553.993(5) or (7), Florida Statues.or individuals licensed as set forth in Section
489.105(3)(f), (g), or (i) or an approved third party. A written report of the results of the test shall be signed by the party conducting the test and
provided to thecode official. Testing shall be performed at any time after creation of all penetrations of the building thermal envelope.
During testing:
1. Exterior windows and doors, fireplace and stove doors shall be closed, but not sealed, beyond the intended weatherstripping or other infiltration
control measures.
2. Dampers including exhaust, intake, makeup air, back draft and flue dampers shall be closed, but not sealed beyond intended infiltration control
measures.
3. Interior doors, if installed at the time of the test, shall be open.
4. Exterior doors for continuous ventilation systems and heat recovery ventilators shall be closed and sealed.
5. Heating and cooling systems, if installed at the time of the test, shall be turned off.
6. Supply and return registers, if installed at the time of the test, shall be fully open.
Testing Company,
Company Name: Phone:
I hereby verify that the above Air Leakage results are in accordance with the 2020 7th Edition Florida Building Code
Energy Conservation requirements according to the compliance method selected above.
Signature of Tester: Date of Test:
Printed Name of Tester:
License/Certification #: Issuing Authority:
1/14/2021 12:35:08 PM EnergyGaugeO USA 7.0.00 - FlaRes202O FBC 7th Edition (2020) Compliant Software Page 1 of 1
Florida Building Code, Energy Conservation, 7th Edition (2020)
Mandatory Requirements for Residential Performance, Prescriptive and ERI Methods
ADDRESS: 5373 San Benedetto Place Permit Number:
Fort Pierce , FL , 34951
MANDATORY REQUIREMENTS - See individual code sections for full details.
, V/
SECTION R401 GENERAL
R401.3 Energy Performance Level (EPL) display card (Mandatory)The building official shall require that an energy performance level (EPL)
display card be completed and certified by the builder to be accurate and correct before final approval of the building for occupancy. Florida law
(Section 553.9085, Florida Statutes) requires the EPL display card to be included as an addendum to each sales contract for both presold and
nonpresold residential buildings. The EPL display card contains information indicating the energy performance level and efficiencies of components
installed in a dwelling unit. The building official shall verify that the EPL display card completed and signed by the builder accurately reflects the plans
and specifications submitted to demonstrate code compliance for the building. A copy of the EPL display card can be found in Appendix RD.
SECTION R402 BUILDING THERMAL ENVELOPE
❑ R402.4 Air leakage (Mandatory). The building thermal envelope shall be constructed to limit air leakage in accordance with the requirements of
Sections R402.4.1 through R402.4.5.
Exception: Dwelling units of R-2 Occupancies and multiple attached single family dwellings shall be permitted to
comply with Section C402.5.
R402.4.1 Building thermal envelopeThe building thermal envelope shall comply with Sections R402.4.1.1 and
R402.4.1.2. The sealing methods between dissimilar materials shall allow for differential expansion and contraction.
R402.4.1.1 Installation. The components of the building thermal envelope as listed in Table R402.4.1.1 shall be installed in accordance
with the manufacturer's instructions and the criteria listed in Table R402.4.1.1, as applicable to the method of construction. Where required
by the code official, an approved third party shall inspect all components and verify compliance.
R402.4.1.2 Testing. The building or dwelling unit shall be tested and verified as having an air leakage rate not exceeding seven air
changes per hour in Climate Zones 1 and 2, and three air changes per hour in Climate Zones 3 through 8. Testing shall be conducted in
accordance with ANSI/RESNET/ICC 380 and reported at a pressure of 0.2 inch w.g. (50 pascals). Testing shall be conducted by either
individuals as defined in Section 553.993(5) or (7), Florida Statutes, or individuals licensed as set forth in Section 489.105(3)(f), (g) or (i) or
an approved third party. A written report of the results of the test shall be signed by the party conducting the test and provided to the code
official. Testing shall be performed at any time after creation of all penetrations of the building thermal envelope.
Exception: Testing is not required for additions, alterations, renovations, or repairs, of the building thermal envelope of existing
buildings in which the new construction is less than 85 percent of the building thermal envelope.
During testing:
1. Exterior windows and doors, fireplace and stove doors shall be closed, but not sealed, beyond the intended weatherstripping or
other infiltration control measures.
2. Dampers including exhaust, intake, makeup air, backdraft and flue dampers shall be closed, but not sealed beyond intended
infiltration control measures.
3. Interior doors, if installed at the time of the test, shall be open.
4. Exterior doors for continuous ventilation systems and heat recovery ventilators shall be closed and sealed.
5. Heating and cooling systems, if installed at the time of the test, shall be turned off.
6. Supply and return registers, if installed at the time of the test, shall be fully open.
R402.4.2 Fireplaces. New wood -burning fireplaces shall have tight -fitting flue dampers or doors, and outdoor combustion air. Where
using tight -fitting doors on factory -built fireplaces listed and labeled in accordance with UL 127, the doors shall be tested and listed for the
fireplace. Where using tight -fitting doors on masonry fireplaces, the doors shall be listed and labeled in accordance with UL 907.
. R402.4.3 Fenestration air leakage. Windows, skylights and sliding glass doors shall have an air infiltration rate of no more than 0.3 cfm
per square foot (1.5 Us/m2), and swinging doors no more than 0.5 cfm per square foot (2.6 L/s/m2), when tested according to NFRC 400 or
AAMA/ WDMA/CSA 101/I.S.2/A440 by an accredited, independent laboratory and listed and labeled by the manufacturer.
Exception: Site -built windows, skylights and doors.
1/14/2021 12:34 PM EnergyGaugeO USA 7.0.00 - FlaRes202O FBC 7th Edition (2020) Compliant Software Page 1 of 5
MANDATORY REQUIREMENTS - (Continued)
R402.4.4 Rooms containing fuel -burning appliances. In Climate Zones 3 through 8, where open combustion air ducts provide combustion air to
open combustion fuel burning appliances, the appliances and combustion air opening shall be located outside the building thermal envelope or
enclosed in a room, isolated from inside the thermal envelope. Such rooms shall be sealed and insulated in accordance with the envelope requirements
of Table R402.1.2, where the walls, floors and ceilings shall meet not less than the basement wall R-value requirement. The door into the room shall be
fully gasketed and any water lines and ducts in the room insulated in accordance with Section R403. The combustion air duct shall be insulated where it
passes through conditioned space to a minimum of R-8.
Exceptions:
Direct vent appliances with both intake and exhaust pipes installed continuous to the outside.
Fireplaces and stoves complying with Section R402.4.2 and Section R1006 of the Florida Building Code, Residential.
❑ R402.4.5 Recessed lighting. Recessed luminaires installed in the building thermal envelope shall be sealed to limit air leakage
between conditioned and unconditioned spaces. All recessed luminaires shall be IC -rated and labeled as having an air leakage rate not
more than 2.0 cfm (0.944 Us) when tested in accordance with ASTM E283 at a 1.57 psf (75 Pa) pressure differential. All recessed
luminaires shall be sealed with a gasket or caulk between the housing and the interior wall or ceiling covering.
R403.1 Controls. SECTION R403 SYSTEMS
❑ R403.1.1 Thermostat provision (Mandatory). At least one thermostat shall be provided for each separate heating and cooling system.
❑ R403.1.3 Heat pump supplementary heat (Mandatory). Heat pumps having supplementary electric -resistance heat shall have controls
that, except during defrost, prevent supplemental heat operation when the heat pump compressor can meet the heating load.
❑ R403.3.2 Sealing (Mandatory) All ducts, air handlers, filter boxes and building cavities that form the primary air containment passageways
for air distribution systems shall be considered ducts or plenum chambers, shall be constructed and sealed in accordance with Section
C403.2.9.2 of the Commercial Provisions of this code and shall be shown to meet duct tightness criteria below.
Duct tightness shall be verified by testing in accordance with ANSI/RESNET/ICC 380 by either individuals as defined in Section 553.993(5) or
(7), Florida Statutes, or individuals licensed as set forth in Section 489.105(3)(f), (g) or (i), Florida Statutes, to be "substantially leak free" in
accordance with Section R403.3.3.
❑ R403.3.2.1 Sealed air handler. Air handlers shall have a manufacturer's designation for an air leakage of no more than 2 percent
of the design airflow rate when tested in accordance with ASHRAE 193.
❑ R403.3.3 Duct testing (Mandatory). Ducts shall be pressure tested to determine air leakage by one of the following methods:
Rough -in test: Total leakage shall be measured with a pressure differential of 0.1 inch w.g. (25 Pa) across the system,
including the manufacturer's air handler enclosure if installed at the time of the test. All registers shall be taped or otherwise
sealed during the test.
Postconstruction test: Total leakage shall be measured with a pressure differential of 0.1 inch w.g. (25 Pa) across the entire
system, including the manufacturer's air handler enclosure. Registers shall be taped or otherwise sealed during the test.
Exceptions:
1. A duct air leakage test shall not be required where the ducts and air handlers are located entirely within the building
thermal envelope.
2. Duct testing is not mandatory for buildings complying by Section 405 of this code. Duct leakage testing is required for Section
R405 compliance where credit is taken for leakage, and a duct air leakage Qn to the outside of less than 0.080 (where Qn =
duct leakage to the outside in cfm per 100 square feet of conditioned Floor area tested at 25 Pascals) is indicated in the
compliance report for the proposed design.
A written report of the results of the test shall be signed by the party conducting the test and provided to the code official.
❑ R403.3.5 Building cavities (Mandatory). Building framing cavities shall not be used as ducts or plenums.
❑ R403.4 Mechanical system piping insulation (Mandatory). Mechanical system piping capable of carrying fluids above 105°F (41 °C)
or below 55°F (13°C) shall be insulated to a minimum of R-3.
❑ R403.4.1 Protection of piping insulation. Piping insulation exposed to weather shall be protected from damage, including that
caused by sunlight, moisture, equipment maintenance and wind, and shall provide shielding from solar radiation that can cause
degradation of the material. Adhesive tape shall not be permitted.
❑ R403.5.1 Heated water circulation and temperature maintenance systems (Mandatory). If heated water circulation systems are
installed, they shall be in accordance with Section R403.5.1.1. Heat trace temperature maintenance systems shall be in accordance with
Section R403.5.1.2. Automatic controls, temperature sensors and pumps shall be accessible. Manual controls shall be readily accessible.
R403.5.1.1 Circulation systems. Heated water circulation systems shall be provided with a circulation pump. The system return pipe shall
❑ be a dedicated return pipe or a cold water supply pipe. Gravity and thermosiphon circulation systems shall be prohibited. Controls for
circulating hot water system pumps shall start the pump based on the identification of a demand for hot water within the occupancy. The
controls shall automatically turn off the pump when the water in the circulation loop is at the desired temperature and when there is no
demand for hot water.
❑ R403.5.1.2 Heat trace systems. Electric heat trace systems shall comply with IEEE 515.1 or UL 515. Controls for such systems shall
automatically adjust the energy input to the heat tracing to maintain the desired water temperature in the piping in accordance with the
times when heated water is used in the occupancy.
1/14/2021 12:34 PM EnergyGauge® USA 7.0.00 - FlaRes202O FBC 7th Edition (2020) Compliant Software Page 2 of 5
MANDATORY REQUIREMENTS - (Continued)
❑ R403.5.5 Heat traps (Mandatory). Storage water heaters not equipped with integral heat traps and having vertical pipe risers shall have
heat traps installed on both the inlets and outlets. External heat traps shall consist of either a commercially available heat trap or a
downward and upward bend of at least 3'Y2 inches (89 mm) in the hot water distribution line and cold water line located as close as possible
to the storage tank.
R403.5.6 Water heater efficiencies (Mandatory).
❑ R403.5.6.1.1 Automatic controls. Service water -heating systems shall be equipped with automatic temperature controls capable
of adjustment from the lowest to the highest acceptable temperature settings for the intended use. The minimum temperature
setting range shall be from 100°F to 140°F (38°C to 60°C).
R403.5.6.1.2 Shut down. A separate switch or a clearly marked circuit breaker shall be provided to permit the power supplied to
electric service systems to be turned off. A separate valve shall be provided to permit the energy supplied to the main burner(s) of
combustion types of service water -heating systems to be turned off.
❑ R403.5.6.2 Water -heating equipment. Water -heating equipment installed in residential units shall meet the minimum efficiencies of
Table C404.2 in Chapter 4 of the Florida Building Code, Energy Conservation, Commercial Provisions, for the type of equipment installed.
Equipment used to provide heating functions as part of a combination system shall satisfy all stated requirements for the appropriate
water -heating category. Solar water heaters shall meet the criteria of Section R403.5.6.2.1.
❑ R403.5.6.2.1 Solar water -heating systems. Solar systems for domestic hot water production are rated by the annual solar energy
factor of the system. The solar energy factor of a system shall be determined from the Florida Solar Energy Center Directory of
Certified Solar Systems. Solar collectors shall be tested in accordance with ISO Standard 9806, Test Methods for Solar Collectors,
and SRCC Standard TM-1, Solar Domestic Hot Water System and Component Test Protocol. Collectors in installed solar
water -heating systems should meet the following criteria:
1. Be installed with a tilt angle between 10 degrees and 40 degrees of the horizontal; and
2. Be installed at an orientation within 45 degrees of true south.
❑ R403.6 Mechanical ventilation (Mandatory). The building shall be provided with ventilation that meets the requirements of the
Florida Building Code, Residential, or Florida Building Code, Mechanical, as applicable, or with other approved means of ventilation
including: Natural, Infiltration or Mechanical means. Outdoor air intakes and exhausts shall have automatic or gravity dampers that
close when the ventilation system is not operating.
❑ R403.6.1 Whole -house mechanical ventilation system fan efficacy. When installed to function as a whole -house mechanical
ventilation system, fans shall meet the efficacy requirements of Table R403.6.1.
Exception: Where an air handler that is integral to tested and listed HVAC equipment is used to provide whole -house mechanical
ventilation, the air handler shall be powered by an electronically commutated motor.
❑ R403.6.2 Ventilation air. Residential buildings designed to be operated at a positive indoor pressure or for mechanical ventilation
shall meet the following criteria:
1. The design air change per hour minimums for residential buildings in ASHRAE 62.2, Ventilation for Acceptable
Indoor Air Quality, shall be the maximum rates allowed for residential applications.
2. No ventilation or air-conditioning system make-up air shall be provided to conditioned space from attics,
crawlspaces, attached enclosed garages or outdoor spaces adjacent to swimming pools or spas.
3. If ventilation air is drawn from enclosed space(s), then the walls of the space(s) from which air is drawn shall be
insulated to a minimum of R-11 and the ceiling shall be insulated to a minimum of R-19, space permitting, or R-10
otherwise.
R403.7 Heating and cooling equipment.
R403.7.1 Equipment sizing (Mandatory). Heating and cooling equipment shall be sized in accordance with ACCA Manual S based
❑ on the equipment loads calculated in accordance with ACCA Manual J or other approved heating and cooling calculation
methodologies, based on building loads for the directional orientation of the building. The manufacturer and model number of the
outdoor and indoor units (if split system) shall be submitted along with the sensible and total cooling capacities at the design
conditions described in Section R302.1. This Code does not allow designer safety factors, provisions for future expansion or other
factors that affect equipment sizing. System sizing calculations shall not include loads created by local intermittent mechanical
ventilation such as standard kitchen and bathroom exhaust systems. New or replacement heating and cooling equipment shall have
an efficiency rating equal to or greater than the minimum required by federal law for the geographic location where the equipment is
installed.
TABLE R403.6.1
WHOLE -HOUSE MECHANICAL VENTILATION SYSTEM FAN EFFICACY
FAN LOCATION
AIRFLOW RATE MINIMUM
(CFM)
MINIMUM EFFICACY a
(CFM/WATT)
AIRFLOW RATE MAXIMU
(CFM)
HRV or ERV
Any
1.2 cfm/watt
Any
Range hoods
Any
2.8 cfm/watt
Any
In -line fan
Any
2.8 cfm/watt
Any
Bathroom, utility room
10
1.4 cfm/watt
<90
Bathroom, utility room
90
2.8 cfm/watt
Any
For SI: 1 cfm = 28.3 L/min. a. When tested in accordance with HVI Standard 916
1/14/2021 12:34 PM EnergyGauge® USA 7.0.00 - FlaRes2020 FBC 7th Edition (2020) Compliant Software Page 3 of 5
MANDATORY REQUIREMENTS - (Continued)
R403.7.1.1 Cooling equipment capacity. Cooling only equipment shall be selected so that its total capacity is not less
than the calculated total load but not more than 1.15 times greater than the total load calculated according to the procedure selected in
Section R403.7, or the closest available size provided by the manufacturer's product lines. The corresponding latent capacity of the
equipment shall not be less than the calculated latent load.
The published value for AHRI total capacity is a nominal, rating -test value and shall not be used for equipment sizing. Manufacturer's
expanded performance data shall be used to select cooling -only equipment. This selection shall be based on the outdoor design dry-bulb
temperature for the load calculation (or entering water temperature for water -source equipment), the blower CFM provided by the expanded
performance data, the design value for entering wet -bulb temperature and the design value for entering dry-bulb temperature.
Design values for entering wet -bulb and dry-bulb temperatures shall be for the indoor dry bulb and relative humidity used for the load
calculation and shall be adjusted for return side gains if the return duct(s) is installed in an unconditioned space.
Exceptions:
1. Attached single- and multiple -family residential equipment sizing may be selected so that its cooling capacity is less than the
2. calculated total sensible load but not less than 80 percent of that load.
When signed and sealed by a Florida -registered engineer, in attached single- and multiple -family units, the capacity of
equipment may be sized in accordance with good design practice.
R403.7.1.2 Heating equipment capacity.
R403.7.1.2.1 Heat pumps. Heat pump sizing shall be based on the cooling requirements as calculated according to Section
R403.7.1.1, and the heat pump total cooling capacity shall not be more than 1.15 times greater than the design cooling load even if
the design heating load is 1.15 times greater than the design cooling load.
R403.7.1.2.2 Electric resistance furnaces. Electric resistance furnaces shall be sized within 4 kW of the design
requirements calculated according to the procedure selected in Section R403.7.1.
R403.7.1.2.3 Fossil fuel heating equipment. The capacity of fossil fuel heating equipment with natural draft atmospheric burners
shall not be less than the design load calculated in accordance with Section R403.7.1.
R403.7.1.3 Extra capacity required for special occasions. Residences requiring excess cooling or heating equipment capacity on an
intermittent basis, such as anticipated additional loads caused by major entertainment events, shall have equipment sized or controlled to
prevent continuous space cooling or heating within that space by one or more of the following options:
1. A separate cooling or heating system is utilized to provide cooling or heating to the major entertainment areas.
2. A variable capacity system sized for optimum performance during base load periods is utilized.
ElR403.8 Systems serving multiple dwelling units (Mandatory). Systems serving multiple dwelling units shall comply with Sections
C403 and C404 of the Florida Building Code, Energy Conservation —Commercial Provisions in lieu of Section R403.
R403.9 Snow melt and ice system controls (Mandatory) Snow- and ice -melting systems, supplied through energy service to the building,
shall include automatic controls capable of shutting off the system when the pavement temperature is above 50°F (10°C), and no
precipitation is falling and an automatic or manual control that will allow shutoff when the outdoor temperature is above 40°F (4.8°C).
❑ R403.10 Pools and permanent spa energy consumption (Mandatory). The energy consumption of pools and permanent spas
shall be in accordance with Sections R403.10.1 through R403.10.5.
R403.10.1 Heaters. The electric power to heaters shall be controlled by a readily accessible on -off switch that is an
integral part of the heater mounted on the exterior of the heater, or external to and within 3 feet (914 mm) of the heater. Operation
of such switch shall not change the setting of the heater thermostat. Such switches shall be in addition to a circuit breaker for the
power to the heater. Gas -fired heaters shall not be equipped with continuously burning ignition pilots.
R403.10.2 Time switches. Time switches or other control methods that can automatically turn off and on according to a preset schedule
shall be installed for heaters and pump motors. Heaters and pump motors that have built-in time switches shall be in compliance with this
section.
Exceptions:
1. Where public health standards require 24-hour pump operation.
2. Pumps that operate solar- and waste -heat -recovery pool heating systems.
3. Where pumps are powered exclusively from on -site renewable generation.
1/14/2021 12:34 PM EnergyGauge® USA 7.0.00 - FlaRes202O FBC 7th Edition (2020) Compliant Software Page 4 of 5
❑ R403.10.3 Covers. Outdoor heated swimming pools and outdoor permanent spas shall be equipped with a vapor -retardant cover on or at
the water surface or a liquid cover or other means proven to reduce heat loss.
Exception: Where more than 70 percent of the energy for heating, computed over an operation season, is from site -recovered
energy, such as from a heat pump or solar energy source, covers or other vapor -retardant means shall not be required.
R403.10.4 Gas- and oil -fired pool and spa heaters. All gas- and oil -fired pool and spa heaters shall have a minimum thermal
❑ efficiency of 82 percent for heaters manufactured on or after April 16, 2013, when tested in accordance with ANSI Z 21.56. Pool
heaters fired by natural or LP gas shall not have continuously burning pilot lights.
R403.10.5 Heat pump pool heaters. Heat pump pool heaters shall have a minimum COP of 4.0 when tested in accordance
with AHRI 1160, Table 2, Standard Rating Conditions -Low Air Temperature. A test report from an independent laboratory is
required to verify procedure compliance. Geothermal swimming pool heat pumps are not required to meet this standard.
R403.11 Portable spas (Mandatory).The energy consumption of electric -powered portable spas shall be controlled by the
requirements of APSP-14.
❑ R403.13 Dehumidifiers (Mandatory If installed, a dehumidifier shall conform to the following requirements:
1. The minimum rated efficiency of the dehumidifier shall be greater than 1.7 liters/ kWh if the total dehumidifier capacity for the house
is less than 75 pints/day and greater than 2.38 liters/kWh if the total dehumidifier capacity for the house is greater than or equal to 75 pints/day.
2. The dehumidifier shall be controlled by a sensor that is installed in a location where it is exposed to mixed house air.
3. Any dehumidifier unit located in unconditioned space that treats air from conditioned space shall be insulated to a minimum of R-2.
4. Condensate disposal shall be in accordance with Section M1411.3.1 of the Florida Building Code, Residential.
❑ R403.13.1 Ducted dehumidifiers. Ducted dehumidifiers shall, in addition to conforming to the requirements of Section R403.13,
conform to the following requirements:
1. If a ducted dehumidifier is configured with return and supply ducts both connected into the supply side of the cooling system, a backdraft
damper shall be installed in the supply air duct between the dehumidifier inlet and outlet duct.
2. If a ducted dehumidifier is configured with only its supply duct connected into the supply side of the central heating and cooling system,
a backdraft damper shall be installed in the dehumidifier supply duct between the dehumidifier and central supply duct.
3. A ducted dehumidifier shall not be ducted to or from a central ducted cooling system on the return duct side upstream from the
central cooling evaporator coil.
4. Ductwork associated with a dehumidifier located in unconditioned space shall be insulated to a minimum of R-6.
SECTION R404
ELECTRICAL POWER AND LIGHTING SYSTEMS
R404.1 Lighting equipment (Mandatory). Not less than 90 percent of the lamps in permanently installed luminaires shall have an
efficacy of at least 45 lumens -per -watt or shall utilize lamps with an efficacy of not less than 65 lumens -per -watt.
R404.1.1 Lighting equipment (Mandatory). Fuel gas lighting systems shall not have continuously burning pilot lights.
1/14/2021 12:34 PM EnergyGauge® USA 7.0.00 - FlaRes2020 FBC 7th Edition (2020) Compliant Software Page 5 of 5