The URL can be used to link to this page

Home My WebLink AboutNOA; Firestone UltraPly TPO SA Single Ply Roof Systems over Concrete DecksMIAMktaADE MIAMI-DADE COUNTY LWAUMM o PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 315-2599 ( � NOTICE OF ACCEPTANCE (NOA) WWW.miamidade.sov/economy Firestone Building Products Company, LLC 200 4th Ave. South Nashville, TN 37201 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Firestone UltraPly TPO SA Single Ply Roof Systems over Concrete Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and v r `6 _ followed by the expiration date may be displayed in advertising literature., If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA consists of pages 1 through 96. The submitted documentation was reviewed by Hamley Pacheco, P.E. MIAMI UADE,C04]NTY FILE COPY IRETTE 14T. ARCH AR 0016279 ?828 N 38 TH AVE LLYWOOD FL�330 90A o.: 21�-0209.02 Expiration Date: 06/13/24 A-proval Date: 06/13/19 • ,'�9 13 Page 1 of 96 r ROOFING SYSTEM APPROVAL Catea-ory Roofing Sub-Cateeorv: Single Ply Roofing Material: TPO SA Deck Tyne: Concrete Maximum Design Pressure See specific assemblies TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Dimensions Specifications Product Description UltraPly TPO SA Various TAS 131 Reinforced TPO 0.045" or 0.060" thick membrane. UltraPly TPO Reinforced Various TAS 131 TPO curb flashing Curb Corner UltraPly 18" Curb Various TAS 131 TPO curb flashing Flashing UltraPly TPO Various TAS 131 Molded TPO for corner flashing Inside/Outside Corner UltraPly TPO Large Pipe Various TAS 131 TPO flashing for large round Flashing penetrations UltraPly TPO T-Joint Various TAS 131 TPO flashing for T joints Cover UltraPly TPO Penetration Various TAS 131 A penetration sealing kit for Kit UltraPly TPO UltraPly TPO Walkway Various TAS 131 TPO walkway pad Pad " UltraPly TPO Coated Various TAS 131 TPO laminated to hot -dipped Metal galvanized steel for flashing UltraPly TPO Premium Various TAS 131 TPO walkway pad Walkway Pad UltraPly TPO Reinforced Various TAS 131 TPO flashing for round Split Pipe Boot penetrations 1" to 9" in diameter UltraPly TPO 8" Various TAS 131 8" wide 60 mil TPO cover strip Reinforced Cover Strip UltraPly TPO Universal Various TAS 131 TPO flashing for round . Pipe Boot penetrations 1" to 6" in diameter UltraPly TPO Various TAS 131 Unreinforced TPO used for Unsupported Flashing flashing SBS Base 3.3" x 50' ASTM 6163 Fiberglass reinforced SBS base sheet SBS Poly Torch Base 39.4" x 33'6" ASTM D 6222 Polyester reinforced modified bitumen membrane. Torch applied. NOA No.: 15-0209.02 MIAMMAOE COUNTY. Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 2 of 96 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Dimensions Specifications Product Description SBS. Glass Torch Base 39.4" x 33'10" ASTM D 6163 Modified bitumen base sheet with a SBS Premium Base SBS Poly Base MB Base BASEGARD SA APP 80 Glass Base V-Force I.S.O. Stick I.S.O. Twin Pack Insulation Adhesive I.S.O. Fix H I.S.O. Spray R SA Primer APPROVED 39.4" x 50' ASTM D 6164 39.4" x 50' ASTM D 6164 36 x 108' ASTM D 4601 39.4" x 65' 3" ASTM D6163 39.4" x 65'4" ASTM D6509 45" x 134" ASTM D 5147, 1876,1970 and ASTM E 96, 2178 5 gal & Proprietary 1500 ml 1500 ml Proprietary 301bs. Proprietary 15 gal pail & Proprietary 55 gal drum 5 gal. Proprietary burn -off film and reinforced with non -woven fiberglass mat. Polyester reinforced SBS modified bitumen ply with sanded surfaces Polyester reinforced SBS modified bitumen membrane with sanded surfaces. Fiberglass reinforced base sheet, asphalt coated on both sides. Applied in hot asphalt or mechanically attached. Fiberglass reinforced SBS modified bitumen, self -adhering base sheet with a smooth sanded surface. Fiberglass reinforced modified bitumen, smooth surfaced base sheet. A vapor retarder made of SBS modified bitumen adhesive laminated to a woven high density polyethylene top surface A dual component polyurethane adhesive. A dual component polyurethane adhesive. A single component polyurethane adhesive. A two-part polyurethane adhesive Polymer based primer NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 3 of 96 APPROVED INSULATIONS: Product Name ISO 95+ GL ISO 95+ GL Tapered ISOGARD HD ISOGARD HD Composite DensDeck Prime RESISTA RESISTA Tapered SECUROCK Gypsum -Fiber Roof Board GenFlex ISO Insulation GenFlex ISO Insulation Tapered Coated Glass Facer Coated Glass Facer Tapered GenFlex HD ISO GenFlex HD Composite ISO APPROVED FASTENERS: Fastener Product Number Name 1. Firestone Heavy -Duty 2. Concrete Drive Fastener TABLE 2 Product Description Manufacturer (With Current NOA) Polyisocyanurate foam insulation Firestone Bldg. Products Polyisocyanurate with a coated Firestone Bldg. Products fiberglass facer Polyisocyanurate with a coated Firestone Bldg. Products fiberglass facer composite insulation. Silicon treated gypsum Georgia Pacific Gypsum LLC Polyisocyanurate foam core laminated Firestone Bldg. Products to a coated fiberglass facer Rigid, gypsum -based board stock United States Gypsum Corp. Polyisocyanurate foam insulation Firestone Bldg. Products Polyisocyanurate foam insulation Firestone Bldg. Products Polyisocyanurate with a coated Firestone Bldg. Products fiberglass facer Polyisocyanurate with a coated Firestone Bldg. Products fiberglass facer composite insulation. TABLE 3 Product Description #15 Fastener for steel, Wood, concrete decks Structural concrete fastener Manufacturer Dimensions (With Current NOA) N/A Firestone Bldg. Products Various Firestone Bldg. Products 3. Insulation Fastening Plate Galvalume insulation plate 3" diameter MIAM14DA0E COUNiY Firestone Bldg. Products NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 4 of 96 EVIDENCE SUBMITTED: Test Aaency Underwriters Laboratories Inc. Factory Mutual Research Corporation TrinitylERD PRI Construction Materials Technologies, LLC MIAMf DADE COUNTY Test Identifier 03NK34486 3004249 3014031 3029384 3030650 3033218 3036642 3039133 3036747 3040535 3035017 3038191 3035560 3047700 3047398 3042666 3041939 3044047 3042665 797-07096-267 797-05604-267 797-05830-267 797-07680-267 797-08513-267 F8300.07.08 F8300.11.08-R3 FBP-038-02-01 FBP-038-02-02 FBP-044-02-01, R10 FBP-053-02-01 FBP-054-02-04, Rev 1 FBP-064-02-01 FBP-076-02-01 FBP-085-02-01, RI FBP-115-02-01 FBP-149-02-01 FBP-154-02-02 FBP-158-02-01 FBP-162-02-01 FBP-165-02-01 FBP-166-02-01 FBP-175-02-01 FBP-176-02-01 FBP-178-02-03 FBP-185-02-02 FBP-206-02-01 Description UL 790 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 4470 TAS 131/ ASTM D6878 TAS 131/ ASTM D6878 ASTM D6164 ASTM D6164 TAS 11411, J TAS 110/ASTM D6131 FM 4474 B/TAS 114 D ASTM D 6509 TAS 110 FM 4474 D/TAS 114 J ASTM D 1644 & 2196 FM 4474 D FM 4474 D FM 4474 D ASTM D 1970 FM 4474/TAS 114 J ASTM D6163 FM 4474 D/TAS 114 J ASTM D 4601 FM 4474 B/TAS 114 D FM 4474 B/TAS 114 D FM 4474 D/TAS 114 J Date 03/22/05 11/03/99 07/22/02 06/07/10 07/10/09 08/12/08 10/09/09 04/07/11 02/12/10 10/05/10 08/22/12 08/04/11 01/11/10 08/16/13 08/15/13 08/14/12 08/14/12 05/17/12 05/04/12 08/22/12 06/07/10 08/30/10 09/12/12 06/18/13 07/30/08 02/25/11 12/27/10 12/28/10 06/01/17 10/08/12 02/07/13 08/02/12 10/23/12 10/04/12 04/04/13 12/18/13 12/18/13 04/28/14 10/02/13 04/28/14 05/15/14 04/28/14 07/15/14 07/23/14 07/31/14 02/02/15 NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 5 of 96 Test Agency Test Identifier Description Date FBP-208-02-01 TAS 131/ASTM D6878 04/06/15 FBP-214-02-01.1 ASTM C 1289 11/09/16 FBP-214-02-02 ASTM C 1289 02/10/15 FBP-222-02-03 TAS 114 C 04/01/15 FBP-225-02-01 FM 4474 D/TAS 114 J 03/19/15 FBP-233-02-03 FM 4474 D/TAS 114 J 06/01/15 FBP-246-02-01 ASTM C 1289 10/05/15 FBP-260-02-02 FM 4474 B 10/09/15 FBP-280-02-01 ASTM C 1289 04/27/16 FBP-293-02-01 ASTM D 4601 04/27/16 FBP-315-02-01 ASTM C 1289 10/28/16 NOA No.: 15-0209.02 .MIAMI DARE COUtdTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 6 of 96 APPROVED ASSEMBLIES Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(1): One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. or with I.S.O. Stick applied in % to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners " Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A Note: Optional middle insulation shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in Y2 to % " wide ribbons spaced 12" o.c. or I.S.O. Stick applied in IWI to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. • One or more layers Additional Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) 1 Density/ftz ISO 95+ GL Tapered, ISO 95+ GL, RESISTA, GenFlex ISO Insulation Tapered, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick NA NA Note: Optional additional middle insulation shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" oxPlease refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Plywood Minimum 19/32" thick MIAMfDARE APPROVED] Insulation Fasteners Fastener (Table 3) Density/fe N/A - N/A NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 7 of 96 Note: Top Insulation layer shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to %"wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: MIAMI�ADB COUNTY -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 8 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(2): Vapor Barrier and insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier V-Force self -adhered to the primed concrete deck. Note: Concrete deck shall be primed with primer -Force WB Primer at a rate of 150-200 ff/gal and allowed to dry prior to application of Vapor Barrier. Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick N/A N/A Note: Insulation shall be adhered to the Vapor Barrier using I.S.O. Spray R, I.S.O. Stick or I.S.O. Twin Pack Adhesive, applied in %" to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design -57.5 psf. using I.S.O. Stick in ribbons 3/a" —1" wide spaced 12" o.c. (See Pressure: General Limitation #9) -97.5 psf using I.S.O. Twin Pack Adhesive in ribbons 3/a" —1" wide spaced 12" o.c. (See General Limitation #9) NOA No.: 15-0209.02 MIAM(-0ADE COUNTY. Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 9 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type A(3): Base layer of insulation mechanically fastened; top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier One ply of BASEGARD SA is self -adhered to a concrete deck primed with SA Primer applied at a rate of 200 ft2/gal. One or more layers Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, GenFlex ISO Insulation Minimum 1-1/2" thick N/A N/A Note: Base Insulation layer shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in %"to 3/a" wide ribbons spaced 12" o.c. or I.S.O. Stick applied in 3/a" to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) ISOGARD HD, GenFlex HD ISO Minimum %'1 thick N/A • ISOGARD 13D Composite, GenFlex HD Composite ISO Minimum 2" thick N/A Fastener Density/ft' N/A N/A Note: Top insulation layer shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %11 to %11 wide beads spaced 12" o.c. or I.S.O. Stick applied in continuous %11 to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 3" wide side laps. Maximum Design Pressure: -90 psf. (See General Limitation #7) NOA No.: 15-0209.02 M AMiDAvE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 10 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: 2500 psi or greater structural concrete or concrete plank System Type A(4): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons, spaced as listed below, Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' DensDeck Prime Minimum %" thick N/A N/A Note: All subsequent layers of insulation shall be adhered to the previous layer of insulation with I.S.O. Twin Pack Insulation Adhesive applied in % to %11 wide ribbons Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -127.5 psf. using I.S.O Twin Pack Insulation Adhesive in ribbons spaced 12" o.c. (See General Limitation #9) -187.5 psf. using I.S.O Twin Pack Insulation Adhesive in ribbons spaced 8" o.c. (See General Limitation #9) -247.5 psf. using I.S.O Twin Pack Insulation Adhesive in ribbons spaced 4" o.c. (See General Limitation #9) NOA No.: 15-0209.02 MU MICADE COUNTY Expiration Date: 06/13/24 ` Approval Date: 06/13/19 Page 11 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated - Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(5): Vapor Barrier and insulation adhered with approved adhesive; membrane adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier: One ply of APP 80 Glass Base torch adhered to the concrete deck. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fF ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1 Y211 thick N/A N/A Note: Base insulation shall be adhered to the vapor barrier I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1 %11 thick N/A N/A Note: Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer (Optional) Insulation Fasteners Fastener _ (Table 3) Density/ff ISO 95+ GL Tapered, RESISTA Tapered, GenFlex ISO Insulation Tapered, Coated Glass Facer Tapered Minimum: %11 thick with a Y41' per ft. taper N/A N/A Note: Optional Top insulation shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -142.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAM1 DADE COUF{TY. Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 12 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(6): One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum: 1" thick N/A N/A Note: Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft ISO 95+ GL Tapered, RESISTA Tapered, GenFlex ISO Insulation Tapered, Coated Glass Facer • Tapered Minimum: %11 thick with a W' per ft. taper N/A N/A Note: Optional Top insulation shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced as listed below Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -142.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 Mwra14Dc►aE caurvnr Expiration Date: 06/13/24 . . P Approval Date: 06/13/19 Page 13 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(7): One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Stick applied in %11 to 1" wide ribbons spaced 12" o.c., Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) ISO 95+ GL, GenFlex ISO Insulation Minimum: 1" thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Stick Pack Insulation Adhesive applied in %" to 1" wide ribbons spaced 12" o.cPlease refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, ISO 95+ GL Tapered, RESISTA, RESISTA Tapered, GenFlex ISO Insulation, GenFlex ISO Insulation Tapered, Coated Glass Facer, Coated Glass Facer Tapered Minimum: 1" thick with a %11 per ft. taper N/A N/A Note: Optional Top insulation shall be adhered to the previous insulation layer with I.S.O. Stick applied in %" to 1" wide ribbons spaced 12" o.cPlease refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -142.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIWIDAOE COUN Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 14 of 96 Membrane Type: Single Ply, Thermoplastic, TPO Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(8): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Note: Base Insulation layer shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in V2" to %11 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/W ISO 95+ GL, GenFlex ISO Insulation, Minimum 1.5" thick N/A N/A Note: Optional Middle Insulation layer shall be adhered to the Base Insulation Layer with I.S.O. Twin Pack Insulation Adhesive applied in %'1 to %11 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener " (Table 3) Density/fe ISOGARD HD, GenFlex HD ISO Minimum'/z" thick N/A N/A Note: Top Insulation layer shall be adhered to the previous layer of roof insulation with I.S.O. Twin Pack Insulation Adhesive applied in %11 to 3/4" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -157.5 psf (See General Limitation #9) NOA No.: 15-0209.02 MIAM14DADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 15 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(9): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. One or more layers of any of the following insulations. Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick N/A N/A Note: All Insulation layers shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in 1/2 to 3/4 in. wide ribbons spaced 12" o.c.. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: WAMIDADE COUNTY -157.5 psf (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 16 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Mn. 2500 psi structural concrete or concrete plank. System Type A(10): One or more layers of insulation adhered with approved adhesive; membrane adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Insulation Insulation Fasteners Fastener (Table 3) Density/ff ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Spray R, I.S.O. Fix H or I.S.O. Stick applied in %" to 1" wide ribbons, spaced 12" o.c. or I.S.O. Twin Pack Insulation Adhesive applied in continuous %" to %11 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -145 psf. (See General Limitation #9) NOA No.: 15-0209.02 MUU41-MOECOUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 17 of 96 Membrane Type: Deck Type 3I: Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. System Type A(11): One or more layers of insulation adhered with approved adhesive; membrane adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ftz ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A Note: Optional Base layer of insulation shall be adhered to the deck with I.S.O. Spray R, I.S.O. Fix II or I.S.O. Stick applied in % to 1" wide ribbons, spaced 12" o.c. or I.S.O. Twin Pack Insulation Adhesive applied in % to 3/a" wide ribbons, spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer DensDeck Prime Minimum 1/4" thick Insulation Fasteners Fastener (Table 3) Density/ff N/A N/A Note: Top layer of insulation shall be adhered with I.S.O. Stick applied in % to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: MAMt-DAUE'GOUNTY .p -160 psf. (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 18 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: 2500 psi or greater structural concrete or concrete plank System Type A(12): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners . Fastener (Table 3) Density/ftz ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Note: Insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to %11 wide ribbons spaced as listed below Please refer to Roofing Application Standard RAS 117 for insulation attachment Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design -165 psf. using I.S.O. Twin Pack Insulation Adhesive with ribbons spaced 12" Pressure: o.c. (See General Limitation #9) -210 psf. using I.S.O. Twin Pack Insulation Adhesive with ribbons spaced 8" o.c. (See General Limitation #9) MU M OADE COUNTY NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 19 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(13): Vapor Barrier and insulation adhered with approved adhesive; membrane adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier: One ply of MB Base, SBS Base, SBS Poly Base or SBS Premium Base fully adhered to the concrete deck with a full mopping of hot asphalt applied at a rate of 20 — 25 lbs./square. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/W Tapered ISO 95+ GL, Tapered GenFlex ISO Insulation Minimum %" thick with a'/a" per ft. taper N/A N/A Top Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ff ISOGARD 1®, GenFlex HD ISO Minimum %11 thick N/A N/A Plywood Minimum 19/32" thick N/A N/A DensDeck Prime Minimum %" thick N/A N/A • Note: Insulation shall be adhered using I.S.O. Twin Pack Insulation Adhesive in continuous %1' to %1' wide beads spaced 12" o.c., I.S.O. Fix II or I.S.O. Stick applied in continuous %11 to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -172.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 MlAt WMDECOUNTY. Expiration Date: 06/13/24 ...vrf ,: Approval Date: 06/13/19 Page 20 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(14): Vapor Barrier and insulation adhered with approved adhesive; membrane adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier One ply of MB Base, SBS Base, SBS Poly Base or SBS Premium Base fully adhered to the concrete deck with a full mopping of hot asphalt applied at a rate of 20 — 25 lbs./square. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base Insulation shall be adhered using I.S.O. Twin Pack Insulation Adhesive in continuous V211 to %'1 wide beads spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe Tapered ISO 95+ GL, ISO 95+ GL, RESISTA Tapered, RESISTA, GenFlex ISO Insulation, Tapered GenFlex ISO Insulation, Coated Glass Facer; Coated Glass Facer Tapered Minimum: 1" thick N/A N/A • Top Insulation Layer Insulation Fasteners Fastener • (Table 3) Density/ft2 DensDeck Prime Minimum:'/" thick N/A N/A • Plywood Minimum 19/32" thick N/A N/A Note: Insulation shall be adhered using I.S.O. Twin Pack Insulation Adhesive in continuous %11 to %11 wide beads spaced 12" o.c., See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design -45 psf (See General Limitation #9) for Plywood Pressure: -60 psf. (See General Limitation #9) for DensDeck Prime NOA No.: 15-0209.02 Mwrrcnaoe country Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 21 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(15): Vapor Barrier and insulation adhered with approved adhesive; membrane • adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier One ply of MB Base, SBS Base, SBS Poly Base or SBS Premium base fully adhered to the concrete deck with a full mopping of hot asphalt applied at a rate of 20 — 25 lbs./square. One or more layers of any of the following insulations. Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISOGARD HD, GenFlex HD ISO Minimum: %11 thick N/A N/A DensDeck Prime Minimum: %11 thick N/A N/A Note: Insulation shall be adhered using I.S.O. Twin Pack Insulation Adhesive in continuous %" to W wide beads spaced 12" o.c., I.S.O. Fix H or I.S.O. Stick applied in continuous W to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: MIAMf DADE COUNTY: ...M , -172.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 22 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: 2500 psi or greater structural concrete or concrete plank System Type A(16): One or more layers of insulation adhered with approved asphalt; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick Top Insulation Layer (Optional) Insulation Fasteners (Table 3) N/A Insulation Fasteners (Table 3) Tapered ISO 95+ GL, Tapered GenFlex ISO Insulation Minimum'/:" thick start with a'/a" per ft. taper N/A Fastener Density/fe N/A Fastener Density/fe N/A Note: Base insulation shall be adhered to the deck in full mopping of approved asphalt within the EVT range and at a rate of 20 to 401bs/100 fe. All subsequent layers of insulation shall be adhered to the previous layer of insulation in full mopping of approved asphalt within the EVT range and at a rate of 20 to 40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels used as a top layer shall be placed with the polyisocyanurate side facing down. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -180 psf. without cover board (See General Limitation #9) NOA No.: 15-0209.02 Muar�� anE cour�rc Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 23 of 96 Membrane Type: Deck Type 3I: • Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. System Type A(17): One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Stick applied in %1' to 1 " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick N/A N/A Note: Optional middle insulation shall be adhered to the previous insulation layer with I.S.O. Stick applied in 3/4 to 1 " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Additional Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL Tapered, ISO 95+ GL, RESISTA Tapered, RESISTA, GenFlex ISO Insulation, Tapered GenFlex ISO Insulation, Coated Glass Facer, Coated Glass Facer Tapered Minimum: 1" thick NA NA Note: Optional additional middle insulation shall be adhered to the previous insulation layer with I.S.O. Stick applied in 3/4 to 111 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer ISOGARD HD, GenFlex HD ISO Minimum %11 thick MIAMI DADE.COUNTY Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 24 of 96 Note: Top Insulation layer shall be adhered to the previous insulation layer with I.S.O. Stick applied in 3/4 to 1 " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 3" • wide side laps. Maximum Design Pressure: 'MIAM14DA9E COUNTY. e s -187.5 psf (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 25 of 96 Membrane Type: Deck Type 3I: • Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. System Type A(18): Vapor Barrier and insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier: V-Force self -adhered to the primed concrete deck with 3" wide side lap. Note: Concrete deck shall be primed with V-Force WB Primer at a rate of 0.25 gal/100 ft' and allowed to dry prior to application of Vapor Barrier. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ff ISO 95+ GL, GenFlex ISO Insulation Minimum: 1/2" thick N/A N/A Note: Base insulation layer shall be adhered to the Vapor Barrier using I.S.O. Spray R ribbon adhesive, applied in %" to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 DensDeck Prime Minimum'/4" thick N/A N/A _ Note: Top insulation layer shall be adhered to the Base insulation layer using I.S.O. Spray R ribbon adhesive, applied in %11 to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -187.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 •MIAMbDADECOUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 26 of 96 Membrane Type: Deck Type 3I: Deck Description: System Type A(19): Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ftz ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Stick applied in %11 to 1 " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ff ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Stick applied in 3/4 to 1 " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Additional Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, ISO 95+ GL Tapered, RESISTA, RESISTA Tapered, GenFlex ISO Insulation, Tapered, GenFlex ISO Insulation, Coated Glass Facer, Coated Glass Facer Tapered Minimum: 1" thick with a %11 per ft. taper N/A N/A Note: Additional Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Stick applied in 3/4 to 1 " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. MIAHIOAOEC UNTY NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 27 of 96 Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft, DensDeck Prime Minimum: 1/4" thick N/A N/A Note: Top insulation shall be adhered to the previous insulation layer with I.S.O. Stick applied in 3/4 to 111 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAMI DAVE cauwrr Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 28 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: 2500 psi or greater structural concrete or concrete plank System Type A(20): One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Use Two (2) base insulation layers Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fts ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Note: Base Insulation layer shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in %" to %11 wide ribbons spaced 8" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer DensDeck Prime Minimum'/4" thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: All subsequent layers of insulation shall be adhered to the previous layer of insulation using I.S.O. Twin Pack Insulation Adhesive applied in %11 to %11 wide ribbons spaced 8" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulations listed as the base layer shall only be used as the base layer with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -195 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAM1 DADE COUNTY: Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 29 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(21): Insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/W ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick N/A N/A Note: Base insulation shall be adhered using ISO Spray R ribbon, applied in %" to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer DensDeck Prime Minimum 1/4" thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: Top insulation shall be adhered using ISO Spray R ribbon, applied in %11 to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -205 psf. (See General Limitation #9) NOA No.: 15-0209.02 MwrsavabE tort Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 30 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 31: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(22): Insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Insulation Fasteners Fastener (Table 3) Density/fF Minimum: 1.5" thick N/A N/A Note: Base insulation shall be adhered using ISO Spray R ribbon, applied in %11 to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -210 psf. (See General Limitation #9) NOA No.: 15-0209.02 M"M QADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 31 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(23): One or more layers of insulation adhered with -approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum: 1" thick N/A N/A Note: Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. One or two layers of the following: • Additional Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL Tapered, ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Tapered GenFlex ISO Insulation, Coated Glass Facer • Minimum: %11 thick with a %" per ft. taper N/A N/A Note: Additional Optional Middle insulation shall be adhered to the base insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % "wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Additional Second Middle Insulation Layer Insulation Fasteners Fastener (Optional) (Table 3) Density/W ISO 95+ GL, ISO 95+ GL Tapered, RESISTA, RESISTA Tapered, GenFlex ISO Insulation, Tapered GenFlex ISO Insulation, Coated Glass Facer, Coated Glass Facer Tapered Minimum: %11 thick with a %11 per ft. taper N/A N/A NOA No.: 15-0209.02 htuartuoaoE couNnr. Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 32 of 96 Note: Optional Second Middle insulation shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation layer Insulation Fasteners Fastener (Table 3) Density/fe DensDeck Prime Minimum %11 thick N/A N/A Note: Top insulation of insulation shall be adhered to the previous layer of insulation using I.S.O. Twin Pack Insulation Adhesive applied in V2" to %11 wide ribbons spaced 8" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -240 psf. (See General Limitation #9) Mwt�ioE cautvTM NOA No.: 15-0209.02 .. � � Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 33 of 96 i A Membrane Type: Deck Type 3I: Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. System Type A(24): Vapor Barrier and insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Vapor Barrier: SBS Poly Torch Base or SBS Glass Torch Base membrane is torch adhered to the primed concrete deck. Note: Concrete deck shall be primed with ASTM D 41 asphalt primer at a rate of 0.75 -1 gal/100 ft2 and allowed to dry prior to application of Vapor Barrier. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A NOTE: Base insulation shall be adhered to the Vapor Barrier using ISO Twin Pack Insulation Adhesive, applied in %" to %11 wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 DensDeck Prime Minimum: %11 thick N/A N/A Note: All subsequent layers of insulation shall be adhered to the previous layer of insulation using I.S.O. Twin Pack Insulation Adhesive applied in %11 to %11 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -232.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 M"14 AUB COUN Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 34 of 96 Membrane Type: Deck Type 3I: Single Ply, TPO, Reinforced Concrete, Insulated Deck Description: 2500 psi or greater structural concrete or concrete plank System Type A(25): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and. System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Top Insulation Layer DensDeck Prime Minimum %" thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: Base insulation shall be adhered to the deck, and top insulation shall be adhered to the base insulation, in full mopping of approved asphalt within the EVT range and at a rate of 20 to 25 lbs/sq. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -247.5 psf. with coverboard (See General Limitation #9) NOA No.: 15-0209.02 Mwt�tt�aflE COUNn Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 35 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(26): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick Middle Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick Top Insulation Layer DensDeck Prime Minimum: %?' thick N/A N/A Insulation Fasteners Fastener (Table 3) Density/ft' N/A N/A Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Note: (Optional) Concrete deck shall be optionally primed with ASTM D 41 asphalt primer at a rate of % to 1 gal/sq. and allowed to dry prior to application of insulation. Insulation shall be adhered to the deck in full mopping of approved asphalt within the EVT range and at a rate of 20 to 25 lbs/sq. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -247.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 MM14)ADE CO, Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 36 of 96 f, Membrane Type: Deck Type 3I: Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. System Type A(27)• One or more layers of insulation adhered with approved adhesive; membrane f illy adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Note: Base Insulation layer shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in %11 to %11 wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick Top Insulation Layer ISOGARD HD, GenFlex HD ISO Minimum %11 thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: Optional Middle Insulation layer shall be adhered to the Base Insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in %11 to %" wide ribbons spaced 12" o.c. Top Insulation layer shall be adhered to the previous layer with Twin Pack Insulation Adhesive applied in %" to %11 wide ribbons spaced 12" o.c Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 3" wide side laps. Maximum Design Pressure: -247.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAM14)4D, COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 37 of 96 Membrane Type: Single Ply, Thermoplastic, TPO Deck Type 31: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(28): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Note: Base Insulation Layer shall be adhered with I.S.O. Fix H, I.S.O. Stick applied in continuous %" to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. (Optional) Middle Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Note: Optional Middle Insulation Layer shall be adhered with I.S.O. Fix H or I.S.O. Stick applied in continuous 3/4 to 1 in. wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer ISOGARD HD, GenFlex HD ISO Minimum %11 thick Insulation Fasteners Fastener (Table 3) Density/ftz N/A N/A Note: Top Insulation layer shall be adhered with I.S.O. Fix H or I.S.O. Stick applied in continuous 3/4 to 1 in. wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation Adhesive Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -300 psf (See General Limitation #9) NOA No.: 15-0209.02 Mwni nape cauNric Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 38 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(29): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulation. Insulation Insulation Fasteners Fastener (Table 3) Density/ft2 ISOGARD HD, GenFlex HD ISO Minimum %11 thick N/A N/A Note: All insulation layers shall be adhered with I.S.O. Fix H applied in continuous %1' to 1" wide ribbons spaced 4" o.c. or I.S.O. Stick applied in continuous %11 to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 3" wide side laps. Maximum Design Pressure: -300 psf. (See General Limitation #9) NOA No.: 9 MIAMMADECO�Expiration iration Date:: 06/106/13/24/24 Approval Date: 06/13/19 Page 39 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(30): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ftz RESISTA, Coated Glass Facer Minimum 1.5" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to % in. wide ribbons spaced 6" o.c. or with I.S.O. Stick or I.S.O. Fix H applied in %11 to 1" wide ribbons, spaced 6" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) RESISTA, Coated Glass Facer Minimum 1.5" thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: Optional middle insulation layer shall be adhered to the previous layer of insulation using the same method of adhesion as the base layer. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer (Optional) ISOGARD HD, GenFlex HD ISO Minimum %11 thick Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Note: Optional top layer of insulation shall be adhered with I.S.O. Stick or I.S.O. Fix H applied in continuous %" to 1" wide ribbons spaced 6" o.c. Please refer to Roofing Application Standard • RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 3" wide side laps. Maximum Design -360 psf. (See General Limitation #9) TPO SA adhered to RESISTA Pressure: -300 psf. (See General Limitation #9) TPO SA adhered to ISOGARD HD NOA No.: 15-0209.02 MIAMt�DALIE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 40 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(31): One or more layers of insulation adhered with approved adhesive; membrane Fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum: 1" thick N/A N/A Note: Base insulation shall be adhered to the deck with I.S.O. Twin Pack Insulation Adhesive applied in % to %"wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A Note: Optional middle insulation shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Additional Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL Tapered, ISO 95+ GL, RESISTA, GenFlex ISO Insulation Tapered, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick NA NA Note: Optional second additional middle insulation shall be adhered.to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Additional Second Middle Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ftz ISO 95+ GL Tapered, ISO 95+ GL, RESISTA, Tapered RESISTA, GenFlex ISO Insulation, Tapered GenFlex ISO Insulation, Coated Glass Facer, Coated Glass Facer Tapered Minimum 1" thick N/A N/A NOA No.: 15-0209.02 MIAMfDADECOUNT'f Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 41 of 96 Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/W ISOGARD HD, GenFlex HD ISO Minimum V2" thick N/A N/A Note: Top Insulation layer shall be adhered to the previous insulation layer with I.S.O. Twin Pack Insulation Adhesive applied in % to % " wide ribbons spaced 12" o.c. or with I.S.O. Spray R, I.S.O. Fix II or I.S.O. Stick applied in % to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -82.5 psf (See General Limitation #9) NOA No.: 15-0209.02 WAMICADE COUN1Tf Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 42 of 96 Membrane Type: Single Ply, Thermoplastic, TPO Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(32): One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. One or more layers of any of the following insulations. Insulation Insulation Fasteners Fastener (Table 3) Density/ft2 ISOGARD HD, GenFlex HD ISO Minimum %11 thick N/A N/A Note: All insulation layers shall be adhered with I.S.O. Stick, applied in continuous 3/" to 1" wide ribbons spaced 4" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 3" wide side laps. Maximum Design Pressure: -300 psf (See General Limitation #9) NOA No.: 15-0209.02 MIAMIIDE GouNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 43 of 96 Membrane Type: Deck Type 3I: Deck Description: System Type A(33): Single Ply, Thermoplastic, TPO Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. One or more layers of insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Base Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Minimum: 1.5" thick Top Insulation Layer DensDeck Prime Minimum: %'1 thick Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Insulation Fasteners Fastener (Table 3) Density/ftz N/A N/A Note: Optional — Concrete deck shall be primed with ASTM D 41 asphalt primer at a rate of % to 1 gal/sq. and allowed to dry prior to application of insulation. Insulation shall be adhered to the deck in full mopping of approved asphalt within the EVT range and at a rate of 20-25 lbs/sq. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -247.5 psf; (See General Limitation #9) NOA No.: 15-0209.02 MUM -DADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 44 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type A(34): Insulation adhered with approved adhesive; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISOGARD HD, GenFlex HD ISO Minimum: 1/2" thick N/A N/A Note: Base insulation shall be adhered using I.S.O. Fix H, I.S.O. Stick, I.S.O. Twin Pack Insulation Adhesive or ISO Spray R ribbon, applied in %" to 1" wide ribbons spaced 12" on center. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: 445 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAMIDAVE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 45 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(1): Base layer of insulation mechanically fastened, optional top layer fully adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick 1 or 2 with 3 Top Insulation Layer (Optional) Insulation Fasteners (Table 3) ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A Tapered ISO 95+ GL, Tapered GenFlex ISO Insulation Minimum %11 thick with a'/a" per ft. taper N/A Fastener Density/ft' 1:2 ft' Fastener Density/fe N/A N/A Note: Base layer shall be mechanically attached with fasteners and density described. All other layers of insulation shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive applied in %11 to 3/a" wide ribbons spaced 12 in. o.c. Insulation panels, listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #7) NOA No.: 15-0209.02 -MLWI DARE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 46 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(2): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum V thick N/A N/A Tapered ISO 95+ GL, Tapered GenFlex ISO Insulation Minimum %11 thick with a'/a" per ft. taper N/A N/A Middle Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ff ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2 %11 thick 1 or 2 with 3 1:4 ft' Note: Optional Base layer shall be loose laid. Middle layer shall be simultaneously fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 1.5" thick N/A N/A Note: Optional top layer shall be adhered to top insulation with I.S.O. Twin Pack Insulation Adhesive in continuous V211 to %11 wide beads spaced 12" o.c. or, I.S.O. Fix II or I.S.O. Stick applied in continuous %1' to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: 45 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAMI-VADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 47 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(3): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener Density/ft' (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick N/A N/A Middle Insulation Layer Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1%" thick 1 or 2 with 3 1:2 fe Note: Optional Base layer shall be loose laid. Middle layer shall be simultaneously fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener Density/ftZ (Table 3) ISOGARD HD, GenFlex HD ISO Minimum %" thick N/A N/A Note: Top layer shall be adhered to top insulation with I.S.O. Twin Pack Insulation Adhesive in continuous %:" to %11 wide beads spaced 12" o.c. or, I.S.O. Fix H or I.S.O. Stick applied in continuous %" to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 Mwrrr anE eouNrY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 48 of 96 Membrane Type: Single Ply,TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(4): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick 1 or 2 with 3 1:2 ft' Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are, used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Middle Insulation Layer Insulation Fasteners (Table 3) ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A Additional Middle Insulation Layer (Optional) Insulation Fasteners (Table 3) ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A Tapered ISO 95+ GL, Tapered GenFlex ISO Insulation Minimum %'1 thick with a %11 per ft. taper N/A Fastener Density/ft' N/A Fastener Density/fe N/A ky;l Note: Middle insulation layers shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %" to %" wide beads spaced 12" o.c. I.S.O. Fix H or I.S.O. Stick applied in continuous 3/4" to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) DensDeck Prime, SECUROCK Gypsum Fiber Roof Board Minimum %1' thick N/A °MIAMIDADE COUNTY Fastener Density/ft' N/A NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 49 of 96 Note: Top layer of insulation shall be adhered to previous layer with I.S.O. Twin Pack Insulation Adhesive in continuous %" to %" wide beads spaced 12" o.c. or I.S.O. Fix II or I.S.O. Stick applied in continuous %" to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" • wide side laps. Maximum Design Pressure: MIAMI-ADE COUNTY -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 50 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(5): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick ' 1 or 2 with 3 1:2 ft' Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Middle Insulation Layer Insulation Fasteners (Table 3) ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A Additional Middle Insulation Layer (Optional) Insulation Fasteners (Table 3) ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A Tapered ISO 95+ GL, Tapered GenFlex ISO Insulation Minimum %'1 thick with a'/4" per ft. taper N/A Fastener Density/ft' N/A Fastener Density/fe N/A N/A Note: Middle insulation layers shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %" to %" wide beads spaced 12" o.c. or I.S.O. Fix H or I.S.O. Stick applied in continuous %" to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft, DensDeck Prime, SECUROCK Gypsum Fiber Roof Board, ISOGARD HD, GenFlex HD ISO Minimum'/:" thick N/A N/A NOA No.: 15-0209.02 CMAMIG �►fle eCouNrY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 51 of 96 Note: Top layer of insulation shall be adhered to previous layer with I.S.O. Twin Pack Insulation Adhesive in continuous %Z" to %" wide beads spaced 12" o.c. or I.S.O. Fix II or I.S.O. Stick applied in continuous 3/a" to 1" wide ribbons spaced 12" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 Mu4MiGAvE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 52 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(6)• Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick 1 or 2 with 3 1:1.6 fe Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board, ISOGARD HD, GenFlex HD ISO Minimum %11 thick N/A N/A ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1%'1 thick N/A N/A Note: Top layer of insulation shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %11 to %11 wide beads spaced 6" o.c. or I.S.O. Fix H or I.S.O. Stick (not for ISOGARD HD (GenFlex HD ISO) or ISOGARD HD Composite (GenFlex HD Composite ISO)) applied in continuous %" to 1" wide ribbons spaced 6 o.c. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Mn. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7) NOA No.: 15-0209.02 Muu`st nwoEtout�nr Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 53 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(7): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ff ISO 95+ GL, , GenFlex ISO Insulation, Minimum 1.5" thick 1 or 2 with 3 1:1.78 ft2 Note: Base layer shall be fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1.5" thick N/A N/A Note: Top layer shall be adhered to base insulation layer with I.S.O. Stick, I.S.O. Fix H or I.S.O. Spray R applied in continuous %'1 to 1" wide ribbons spaced 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7) NOA No.: 15-0209.02 KMANDAUE'GOUN Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 54 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(8): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1.78 ft2 Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Middle Insulation Layer Insulation Fasteners (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A Fastener Density/ft2 N/A Note: Middle Insulation shall be adhered with I.S.O. Twin Pack Insulation Adhesive in continuous V211 to 3/a" wide ribbons spaced 6" o.c. or I.S.O. Spray R applied in continuous %11 to 1" wide ribbons spaced 6" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer ISOGARD HD, GenFlex HD ISO Minimum %11 thick Insulation Fasteners Fastener (Table 3) Density/ftz N/A N/A Note: Top layer of insulation shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %" to %" wide ribbons spaced 6" o.c. or I.S.O. Spray R, I.S.O. Fix H or I.S.O. Stick applied in continuous %11 to 1" wide ribbons spaced 6" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7): NOA No.: 15-0209.02 MAMr-DADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 55 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(9): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ftz ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1.78 fe Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Top Insulation Layer ISOGARD HD, GenFlex HD ISO Minimum %11 thick Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Note: Top insulation layer shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %11 to %11 wide ribbons spaced 6" o.c. or I.S.O. Spray R, I.S.O. Fix H or I.S.O. Stick applied in continuous 3/a" to 1" wide ribbons spaced 6" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -67.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 CMLMA AUE COUNTY Expiration Date:-06/13/24 020902 Approval Date: 06/13/19 Page 56 of 96 Membrane Type: Deck Type 3I: Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank System Type B(10): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 2" thick 1 or 2 with 3 1:1.78 ft2 Note: Base layer shall be fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe SECUROCK Gypsum Fiber Roof Board Minimum %11 thick N/A N/A Note: Top layer shall be adhered to top insulation with I.S.O. Stick applied in continuous %" to 1" wide ribbons spaced 6" o.c. or I.S.O. Spray R applied in continuous %" to 1" wide ribbons spaced 6" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -67.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 Muarsi�aoe 1UNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 57 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(11): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GeuFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1.6 ft2 Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are ,used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Top Insulation Layer ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick Insulation Fasteners Fastener (Table 3) Density/ft2 N/A N/A Note: Top layer of insulation shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous'/:" to %11 wide beads spaced 6" o.c., I.S.O. Fix II or I.S.O. Stick applied in continuous 3/a" to 1" wide ribbons spaced 6" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: - 75 psf. (See General Limitation #7) NOA No.: 15-0209.02 MLAW If 4 =E.cOUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 58 of 96 Membrane Type: Deck Type 7I: Deck Description: Single Ply, TPO, Reinforced Recover, Insulated Min. 2500 psi structural concrete or concrete plank. System Type B(12): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/W ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A ISO 95+ GL Tapered, GenFlex ISO Insulation Tapered Minimum %11 thick with a %11 per ft. taper N/A N/A Middle Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1.6 ft2 Note: Middle layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/W ISOGARD HD, GenFlex HD ISO Minimum 1/2" thick N/A N/A Note: Top layer of insulation shall be adhered to middle insulation layer with I.S.O. Twin Pack Insulation Adhesive in continuous %"to %" wide ribbons spaced 6" o.c. or I.S.O. Fix H or I.S.O. Stick applied in continuous W1 to 1" wide ribbons spaced 6" o.c. See Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -82.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAMfUADECOUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 59 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(13): Base layer of insulation mechanically fastened, top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more. layers of any of the following insulations: Base Insulation Layer RESISTA, Coated Glass Facer Minimum 1.5" thick Top Insulation Layer RESISTA, Coated Glass Facer Minimum 1.5" thick Insulation Fasteners Fastener (Table 3) Density/ft2 1 or 2 with 3 1:1 ft2 Insulation Fasteners Fastener (Table 3) Density/fe N/A N/A Note: Base layer shall be mechanically attached with fasteners and density described. Top layer of insulation shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %" to %" wide beads spaced 12" o.c. or I.S.O. Stick, I.S.O. Fix II applied in continuous %11 to 1" wide ribbons spaced 12" o.c. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -120 psf. (See General Limitation #7) Mwr�► arseUN courser NOA No.: 15-0209.02 � Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 60 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(14): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1 ftz Note: Base layer shall be fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A Note: Top layer shall be adhered to top insulation with I.S.O. Twin Pack Insulation Adhesive in continuous'/:" to 3/a" wide beads spaced 4" o.c. or, I.S.O. Fix II or I.S.O. Stick applied in continuous %'1 to 1" wide ribbons spaced 4" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -127.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAM14DADE GOUNiY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 61 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(15): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) 1 Density/ff ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1 ftz Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ftz DensDeck Prime, ISOGARD HD, GenFlex HD ISO Minimum %" thick N/A N/A ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1%11 thick N/A N/A Note: Base layer shall be mechanically attached with fasteners and density described. Top layer of insulation shall be adhered to base insulations with I.S.O. Twin Pack Insulation Adhesive in continuous %" to V wide beads spaced 4" o.c., I.S.O. Fix H or I.S.O. Stick (not for ISOGARD HD (GenFlex HD ISO) (or ISOGARD HD Composite (GenFlex ]RD Composite ISO)) applied in continuous %11 to 1" wide ribbons spaced 4" o.c. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -127.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIJA R )ADE GOUN. Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 62 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(16): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick N/A N/A Middle Insulation Layer Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 - 1:1 ft, Note: Base layer shall be loose laid. Middle layer shall be simultaneously fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener Density/ftz (Table 3) ISOGARD BD, GenFlex 13D ISO Minimum 1/2" thick N/A N/A Note: Top layer shall be adhered to top insulation with I.S.O. Twin Pack Insulation Adhesive in continuous %" to %" wide ribbons spaced 4" o.c. or, I.S.O. Fix H or I.S.O. Stick applied in continuous %11 to 1" wide ribbons spaced 4" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" Maximum Design Pressure: MIAM14DADE COUNTY. wide side laps. -135 psf. (See General Limitation #7) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 63 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type B(17): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick N/A N/A Middle Insulation Layer Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1 ft2 Note: Base layer shall be loose laid. Middle layer shall be simultaneously fastened with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener Density/ft2 (Table 3) ISOGARD HD, GenFlex HD ISO Minimum %'1 thick N/A N/A Note: Top layer shall be adhered to top insulation with I.S.O. Twin Pack Insulation Adhesive in continuous %'1 to %11 wide ribbons spaced 4" o.c. or, I.S.O. Fix H or I.S.O. Stick applied in continuous 3/a" to 1" wide ribbons spaced 4" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil. U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -135 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAM14DADE COIUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 64 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(1): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum 1" thick N/A N/A ISO 95+ GL Tapered, GenFlex ISO Insulation Tapered Minimum %11 thick with a 1/a" per ft. taper N/A N/A Middle Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, GenFlex ISO Insulation Minimum 1-1/2" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ' ISOGARD HD, GenFlex HD ISO Minimum %11 thick 1 or 2 with 3 1:2.1 ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer ' Minimum 1" thick 1 or 2 with 3 1:2.1 ft2 . DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/4" thick 1 or 2 with 3 1:2.1 ft2 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/211 thick 1 or 2 with 3 1:2.1 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger'panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. NOA No.: 15-0209.02 Mt1W14=E C0U TY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 65 of 96 Membrane: Maximum Design Pressure: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAMICADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 66 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Mn. 2500 psi structural concrete or concrete plank. System Type C(2): All layers of insulation simultaneously attached membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlez ISO Insulation, Coated Glass Facer Minimum 1" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe SECUROCK Gypsum -Fiber Roof Board Minimum V411 thick 1 or 2 with 3 1:1.78 fe RESISTA, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1:1.78 ft' ISO 95+ GL, ISOGARD HD Composite, GenFlez ISO Insulation, GenFlez HD Composite ISO Minimum 1.5" thick 1 or 2 with 3 1:1.78 ff DensDeck Prime Minimum V211 thick 1 or 2 with 3 1:1.78 ft2 Note: All layers shall be simultaneously fastened. See top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions. If larger panels are used, the number _ of fasteners shall be increased using the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: MIAMIDADE C-0 -45 psf. (See General Limitation #7) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 67 of 96 Membrane Type: Deck Type 3I: Deck Description: Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. System Type C(3): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations: Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:2.67 ft' DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1:2.67 ft2 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:2.67 ftz Note: All layers shall be simultaneously fastened. See top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions. If larger panels are used, the number of fasteners shall be increased using the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: MIAM DADE COUN -45 psf. (See General Limitation #7) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 68 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(4): Membrane bonded over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick N/A N/A Middle Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1/2" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1:5.3 ftz ISOGARD HD, GenFlex HD ISO Minimum %" thick 1 or 2 with 3 1:5.3 ff DensDeck Prime, SECUROCK Gypsum Fiber Roof Board Minimum %11 thick 1 or 2 with 3 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 Plywood Minimum 19/32" thick 1:5.3 fe 1:5.3 ft' 1 or 2 with 3 1:5.3 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. NOA No.: 15-0209.02 M AMI.Oc►ue COUN Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 69 of 96 Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAMICADE COUNT'! Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 70 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(5): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ff ISOGARD HD, GenFlex HD ISO Minimum %" thick 1 or 2 with 3 1:2.7ft2 ISO 95 + GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1:2.7 ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum %11 thick 1 or 2 with 3 1:2.7 fe ISOGARD HD Composite, GenFlex HD ISO Composite Minimum 1.5" thick 1 or 2 with 3 1:2.7 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil. U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 MIAM14MUE COUNTY- Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 71 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(6): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISOGARD HD, GenFlex HD ISO Minimum 1" thick 1 or 2 with 3 1: 1.78 ft2 ISO 95 + GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1: 1.78 ft' DensDeck Prime, SECUROCK Gypsum -Fiber Boards Minimum 1/4" thick 1 or 2 with 3 1: 1.78 fe ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1.78 fe • Note: All layers shall be simultaneously fastened; see top layer for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. • Maximum Design Pressure: -45 psf. (See General Limitation #7) NOA No.: 15-0209.02 M�rrtuanecoucrry Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 72 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(7): Base layer of insulation mechanically fastened, optional top layer adhered with approved adhesive All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL, GenFlex ISO Insulation Minimum 1-1/2" thick N/A N/A Middle Insulation Layer (Optional) Insulation Fasteners Fastener Density/ft2 (Table 3) ISO 95+ GL Tapered, GenFlex ISO Insulation Tapered Minimum 1/2" thick N/A N/A Note: Base layer shall be loose laid. Middle layer shall be preliminary fastened. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for fastening details. Top Insulation Layer Insulation Fasteners Fastener Density/ft2 (Table 3) DensDeck Prime, SECUROCK Gypsum Fiber Roof Board Minimum 1/4" thick 1 or 2 with 3 1:2 ff ISOGARD HD Composite, ISO 95+ GL, GenFlex IID Composite ISO, GenFlex ISO Insulation Minimum 1-1/2" thick 1 or 2 with 3 1:2 W RESISTA, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1:2 ff Plywood Minimum 19/32" thick 1 or 2 with 3 1:2 fe Note: All layers shall be simultaneously fastened; see top layer for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. NOA No.: 15-0209.02 Mwrri�ue►aE couNrr Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 73 of 96 Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 MWM��AUE COUNiY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 74 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(8): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved, membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlez ISO Insulation, Coated Glass Facer Minimum 1%" thick 1 or 2 with 3 1:2.7 fe DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1:2.7 ft2 ISOGARD HD Composite, GenFlez HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:2.7 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 M[WIDADE.COUNT"E Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 75 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type C(9): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ff ISO 95+ GL, RESISTA, GenFlez ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ftz RESISTA, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1:1.6 fe ISO 95 + GL, ISOGARD HD Composite, GenFlez ISO Insulation, GenFlez HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3. 1:1.6 fe SECUROCK Gypsum Fiber Roof Board, DensDeck Prime Minimum %" thick 1 or 2 with 3 1:1.6 fe Note: All layers shall be simultaneously fastened. See top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions. If larger panels are used, the number of fasteners shall be increased using the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. • Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design -52.5 psf. (See General Limitation #7) Pressure: MM4ECOMUMSrNOA No.: 15-0209.02 M Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 76 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(10): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %"thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) DensDeck Prime, SECUROCK Gypsum Fiber Roof Board Minimum %11 thick 1 or 2 with 3 RESISTA, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1.5" thick 1 or 2 with 3 Fastener Density/ft2 1:.1.78 ft2 1:.1.78 ft2 1:.1.78 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -52.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAMI-DAD' COUNTYExpiration Date: 06/13/24 Approval Date: 06/13/19 Page 77 of 96 Membrane Type: Single Ply, Thermoplastic, TPO Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type C(11): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %"thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, ISOGARD HD Composite, RESISTA, GenFlex ISO Insulation, Coated Glass Facer, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1: 1.78 ftz DensDeck Prime, SECUROCK Gypsum Fiber Roof Board Minimum %11 thick 1 or 2 with 3 1: 1.78 ft2 Note: All layers shall be simultaneously fastened. See top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions. If larger panels are used, the number of fasteners shall be increased using the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7) NOA No.: 15-0209.02 "UMD Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 78 of 96 i Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(12): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %"thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe SECUROCK Gypsum -Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1: 2.13 ft' ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1: 2.13 W Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with l .5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7) COUNTY Expiration Date: 06/13/24 ' NOA No.: 15-0209.02 AMIAM14=6... W Approval Date: 06/13/19 Page 79 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(13): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %" thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1" thick 1 or 2 with 3' Fastener Density/ft' 1: 1.33 fe Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with '1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7) NOA No.: 15-0209.02 Miarf! oa►nE counn Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 80 of 96 Membrane Type: Deck Type 3I: Deck Description: System Type C(14): Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. Membrane bonded over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISOGARD HD, GenFlex HD ISO Minimum'/:" thick 1 or 2 with 3 1:4 ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick 1 or 2 with 3 1:4 W SECUROCK Gypsum Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1:4 ftz DensDeck Prime Minimum %11 thick 1 or 2 with 3 1:4 fe ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-112" thick 1 or 2 with 3 1:4 ft2 Plywood Minimum 19/32" thick 1 or 2 with 3 1:4 fe Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -60 psf. (See General Limitation #7) Mu�rn�ave counanr NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 81 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(15): Membrane fully adhered over mechanically fastened insulation All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ftz ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 SECUROCK Gypsum -Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1: 4.0 ft2 ISOGARD )® Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1: 4.0 ff Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: CAIMAM14DADE -62.5 psf. (See General Limitation #9) NOA No.: 15-0209.02 Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 82 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(16): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1/2" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe SECUROCK Gypsum -Fiber Roof Board Minimum V2" thick 1 or 2 with 3 1:1.6 fe ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1.6 fe Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: —67.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAMMAaE ClOUN1Y Expiration Date: 06/13/24 � . p. Approval Date: 06/13/19 Page 83 of 96 Membrane Type: Deck Type 3I: Deck Description: System Type C(17): Single Ply, TPO, Reinforced Concrete, Insulated Min. 2500 psi structural concrete or concrete plank. Membrane bonded over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners (Table 3) ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1.5" thick N/A Top Insulation Layer Plywood Minimum 19/32" thick ISOGARD HD, GenFlex BD ISO Minimum %" thick Insulation Fasteners (Table 3) 1 or 2 with 4 1 or 2 with 4 Fastener Density/W N/A Fastener Density/ft2 1:2.7 ft2 1:2.7 ft2 DensDeck Prime, SECUROCK Gypsum Fiber Roof Board Minimum %11 thick 1 or 2 with 4 1:2.7 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with. 1.5" wide heat weld at the 6" wide side laps. Maximum Design Pressure: -75 psf. (See General Limitation #7) NOA No.: 15-0209.02 Mti°; can Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 84 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(18): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations: Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 RESISTA, ISOGARD HD Composite, Coated Glass Facer, GenFlex,HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1.6 ft2 ISO 95 + GL, GenFlex ISO Insulation Minimum 2" thick 1 or 2 with 3 1:1.6 ft' DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1:1.6 ft2 Note: All layers shall be simultaneously fastened. See top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions. If larger panels are used, the number of fasteners shall be increased using the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -75 psf. (See General Limitation #7) NOA No.: 15-0209.02 tMWNtt OV1E7E GOt7Nl Y Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 85 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type.C(19): All layers of insulation simultaneously attached; membrane bonded. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 1/21' thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 SECUROCK Gypsum Fiber Roof Board Minimum %11 thick 1 or 2 with 3 1:1.78 fe ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1.78 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -82.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 Muartiane touNrt Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 86 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(20): Membrane adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1.6 ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum %11 thick 1 or 2 with 3 1:1.6 ftz ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1.6 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -82.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MUAMIDAOE COUNTY= Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 87 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(22): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 RESISTA, ISO 95+ GL, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1 fe SECUROCK Gypsum -Fiber Roof Board, DensDeck Prime Minimum %11 thick 1 or 2 with 3 1:1 ft2 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1 ft, Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressures: -150 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAMI DADE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 89 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(23): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved. and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ftz ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1.5" thick 1 or 2 with 3 1: 1.33 ft' Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -112.5 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAMGOADE COUNTY. Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 90 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(24): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ff ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 2" thick 1 or 2 with 3 1: 1.33 fe Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -120 psf. (See General Limitation #7) NOA No.: 15-0209.02 MIAMtDADE COUNTY Expiration Date: 06/13/24 9 Approval Date: 06/13/19 Page 91 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(25): Membrane adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum %" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, GenFlex ISO Insulation, Coated Glass Facer Minimum 2" thick 1 or 2 with 3 1:1 ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/2" thick 1 or 2 with 3 1:1 ft, ISOGARD HD Composite, GenFlex HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1:1 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -142.5 psf. with ISO 95+ GL, RESISTA, DensDeck Prime, or ISOAGRD HD Composite (See General Limitation #7) -112.5 psf. with SECUROCK Gypsum Fiber Roof Board (See General Limitation #7) NOA No.: 15-0209.02 MIAMIJDIAaE COUNTY Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 92 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Concrete, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(26): All layers of insulation simultaneously attached; membrane fully adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table L (Optional) Vapor Retarder Polyethylene Sheet 4-6 mil thick Min. 2" wide laps sealed with duct tape One or more layers of any of the following insulations. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, ISO 95 + GL Tapered, RESISTA, RESISTA Tapered, GenFlez ISO Insulation, Tapered GenFlez ISO Insulation, Coated Glass Facer, Coated Glass Facer Tapered Minimum 1-1/2" thick N/A N/A T9p insulation Layer Insulation :Fasteners Fastener (Table 3) Ilensity/ft2 SECUROCK Gypsum -Fiber Roof Board I Minimum 1/21' thick 1 or 2 with 3 1:4 ft2 ISOGARD HD Composite, GenFlez HD Composite ISO Minimum 1-1/2" thick 1 or 2 with 3 1: 4 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil UltraPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design Pressure: -45 psf. (See General Limitation #9) NOA No.: 15-0209.02 "MWAMI-�DADE UN Expiration Date:-06/13/24 0209.02 Approval Date: 06/13/19 Page 93 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I Steel, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank. System Type C(27): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/fe ISO 95+ GL, RESISTA, DensDeck Prime, GenFlez ISO Insulation, Coated Glass Facer Minimum V2" thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) ISOGARD HD Composite, GenFlez HD Composite ISO Minimum 1 %11 thick 1 or 2 with 3 Fastener Density/fe 1:2.13 ft2 Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design -67.5 psf. (See General Limitation #7) Pressure: NOA No.: 15-0209.02 MIAMIDWDEGOWNTT Expiration Date: 06/13/24 all Approval Date: 06/13/19 Page 94 of 96 Membrane Type: Single Ply, TPO, Reinforced Deck Type 3I: Steel, Insulated Deck Description: Min. 2500 psi structural concrete or concrete plank System Type C(28): Membrane fully adhered over mechanically fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer (Optional) Insulation Fasteners Fastener (Table 3) Density/ft2 ISO 95+ GL, RESISTA, DensDeck Prime, GenFlez ISO Insulation, Coated Glass Facer Minimum %11 thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/fe ISOGARD HD Composite, GenFlez HD Composite ISO Minimum 1 %11 thick 1 or 2 with 3 1:1.78 fe Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density. See Roofing Application Standard RAS 117 for fastening details. Membrane: Min. 45 mil U1traPly TPO SA self -adhered with 1.5" wide heat weld at the 2" wide side laps. Maximum Design -75 psf. (See General Limitation #7) Pressure: NOA No.: 15-0209.02 MIAMI DIADE COUNTY: Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 95 of 96 y CONCRETE DECK SYSTEM LmTATIONS: 1. If mechanical attachment to the structural deck through the lightweight insulating concrete is proposed, a field withdrawal resistance testing shall be performed to determine equivalent or enhanced fastener patterns and density. All testing and fastening design shall be in compliance with Testing Application Standard TAS 105 and Roofing Application Standard RAS 117 and/or RAS 137, calculations shall be signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer. 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down,the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf. 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 lbf. Insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117 and/or RAS 137. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9N-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE NOA No.: 15-0209.02 CMWQiMDE Cavnrr Expiration Date: 06/13/24 Approval Date: 06/13/19 Page 96 of 96