The URL can be used to link to this page

Home My WebLink AboutAPPROVED, Product Approval, WinDoor.20080603 NOA No. 20-0806.03 Expiration Date: May 30, 2024 Approval Date: November 25, 2020 Page 1 MIAMI–DADE COUNTY, FLORIDA PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315–2590 F (786) 315–2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy Windoor Inc., 107 Triple Diamond, Venice, Fl. 34275 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami–Dade County RER–Product Control Section to be used in Miami–Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami–Dade County Product Control Section (In Miami–Dade County) and/ or the AHJ (in areas other than Miami–Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami–Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Series “TD9050” Outswing Aluminum Terrace Door – L.M.I. APPROVAL DOCUMENT: Drawing No. 9050-OS-NOA-1 Rev A, titled “Alum. Outswing Terrace Door, (LMI)”, sheets 1 through 9 of 9, dated 01/05/19 and last revised on 07/21/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E., bearing the Miami–Dade County Product Control Section Revision stamp with the Notice of Acceptance number and Revision date by the Miami–Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant Limitations: 1. See Design Pressure (DP) Vs Glass type, size and Elevation anchor lay out for Single door in sheet 2 and double door in sheet 3. 2. See Jamb anchor for Single and Double Door in sheet 5. See double door Cluster anchors at head and sill and cluster layout at astragal/meeting stiles in sheet 4. Intermediate anchors are per Elevation Layout. 3. See illustrative door selection and installation Examples in sheet 5. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, model/ series, and following statement: "Miami–Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami–Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No. 19-0205.02 consists of this page 1 and evidence pages E–1, E-2 and E-3, as well as approval document mentioned above. The submitted documentation was reviewed by Ishaq I. Chanda, P. E. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0806.03 Expiration Date: May 30, 2024 Approval Date: November 25, 2020 E – 1 Windoor Inc., NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA A. DRAWINGS 1. Manufacturer's die drawings and sections. 2. Drawing No. 9050-OS-NOA-1, titled “Alum. Outswing Terrace Door, (LMI)”, sheets 1 through 9 of 9, dated 05/01/19, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P. E. B. TESTS 1. Test reports on 1) Air Infiltration Test, per FBC, TAS 202–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3) Water Resistance Test, per FBC, TAS 202–94 4) Large Missile Impact Test per FBC, TAS 201–94 5) Cyclic Wind Pressure Loading per FBC, TAS 203–94 6) Forced Entry Test, per FBC 2411.3.2.1, and TAS 202–94 along with marked–up drawings and installation diagram of an aluminum outswing Terrace Door, prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL–17789, dated 12/10/18, signed and sealed by Idalmis Ortega, P. E. C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 6th Edition (2017), prepared by manufacturer, dated 01/14/19 and last revised on 05/01/19, signed and sealed by A. Lynn Miller, P. E. 2. Glazing complies with ASTM E1300–04/ 09 D. QUALITY ASSURANCE 1. Miami–Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 17-1114.14 issued to Kuraray America, Inc. for their “Trosifol® Ultraclear, Clear, and Color PVB Glass Interlayers” expiring on 07/08/19. 2. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. (Former E.I. DuPont DE Nemours & Co., Inc. for the “Sentry Glass ® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 3. Architectural Testing Test report # 60520 dated 12/18/2005, issued to Ensinger Inc., for Techatherm 66GF (insulbar) tested per ASTM G-155-00, ASTM D 638-03, ASTM D 635- 98, ASTM D 1929-96 and ASTM D 2843-99, signed and sealed by Joseph A. Reed, P.E. F. STATEMENTS 1. Statement letter of conformance with FBC 6th Edition (2017) and “No financial interest”, issued by manufacturer, dated 01/15/19, signed and sealed by A. Lynn Miller, P. E. 2. Lab compliance as part of the above referenced Test Report. G. OTHERS 1. Test proposal # 17-026-R dated May 18, 2017 approved by RER. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0806.03 Expiration Date: May 30, 2024 Approval Date: November 25, 2020 E – 2 Windoor Inc., NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 2. NEW EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. 9050-OS-NOA-1 Rev A, titled “Alum. Outswing Terrace Door, (LMI)”, sheets 1 through 9 of 9, dated 01/05/19 and last revised on 07/21/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. B. TESTS 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per ASTM F588 and TAS 202-94 along with marked-up drawings and installation diagram of all Windoor Inc., CGI Windows and Doors, Inc. and PGT Industries, Inc., representative units listed below and tested to qualify Dowsil 791 and Dowsil 983 silicones, per Proposal #19-1155TP, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.: WinDoor, Inc. test specimens: FTL-20-2078.1, WinDoor PW3000 Aluminum Fixed Lite (unit 11 in proposal) FTL-20-2078.2, WinDoor HR9470 Thermally Broken Alum. Horiz. Roller (unit 12) FTL-20-2078.3, WinDoor SGD8100 Alum. Sliding Glass Door (unit 13 in proposal) FTL-20-2078.4, WinDoor HR9470 Thermally Broken Alum. Horiz. Roller (unit 14) FTL-20-2078.5, WinDoor PW9020 Alum. Fixed Lite (unit 15 in proposal) and FTL-20-2078.6, WinDoor PW9020 Alum. Fixed Lite (unit 16 in proposal), all dated 09/24/20 and signed and sealed by Idalmis Ortega, P.E. CGI Windows and Doors Inc. test specimens: FTL-20-2108.1, CGI SH360 Aluminum Single Hung Window (unit 1 in proposal) FTL-20-2108.2, CGI CA238 Alum. Outswing Casement Window (unit 2 in proposal) FTL-20-2108.3, CGI SGD560 Aluminum Sliding Glass Door (unit 3 in proposal) FTL-20-2108.4, CGI PW410 Aluminum Fixed Window (unit 4 in proposal) and FTL-20-2108.5, CGI SH360 Aluminum Single Hung Window (unit 5 in proposal)all dated 08/24/20 and signed and sealed by Idalmis Ortega, P.E. PGT Industries, Inc. test specimens: FTL-7897, PGT PW5520 PVC Fixed Window (unit 6 in proposal), dated 09/03/14 FTL-20-2107.1, PGT SGD780 Aluminum Sliding Glass Door (unit 7 in proposal) FTL-20- 2107.2, PGT CA740 Alum. Outswing Casement Window (unit 8 in proposal) FTL-20-2107.3, PGT PW7620A Aluminum Fixed Window (unit 9 in proposal) and FTL-20-2107.4, PGT PW7620A Aluminum Fixed Window (unit 10 in proposal) all dated 07/13/20 and signed and sealed by Idalmis Ortega, P.E. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0806.03 Expiration Date: May 30, 2024 Approval Date: November 25, 2020 E – 3 Windoor Inc., NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 2. NEW EVIDENCE Continue: C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 7th Edition (2020), dated 07/21/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2. Glazing complies with ASTM E1300-04, -09, -12 and -16. D. QUALITY ASSURANCE 1. Miami Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for their “Trosifol® Ultraclear, Clear and Color PVB Glass Interlayers”, expiring on 07/08/24. 2. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 3. Architectural Testing Test report # 60520 dated 12/18/2005, issued to Ensinger Inc., for Techatherm 66GF (insulbar) tested per ASTM G-155-00, ASTM D 638-03, ASTM D 635- 98, ASTM D 1929-96 and ASTM D 2843-99, signed and sealed by Joseph A. Reed, P.E. F. STATEMENTS 1. Statement letters of conformance to FBC 2020(7th Edition), dated 07/21/20, prepared, signed & sealed by Lynn Miller, P. E. 2. Statement of Lab compliance as part of the test report. G. OTHER 1. This NOA revises NOA No. 19-0205.02 and updates to FBC 2020 (7th Edition) expiring 05/30/24. 2. RER Test proposals #19-1155 dated 01/10/20 approved by Ishaq I. Chanda, P.E.