HomeMy WebLinkAboutAPPROVED NOA-Modified over cementMIAMF
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE OF ACCEPTANCE (NOA)
CertainTeed LLC.
20 Moores Road
Malvern, PA 19355
SCOPE:
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786)315-2590 F (786) 31525-99
www.miamidade.gov/economy
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to
have this product or material tested for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to
revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: CertainTeed Modified Bitumen Roof System over Concrete Decks.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA No. 19-1028.11 and consists of pages 1 through 87.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 20-0723.27
CMSTe Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 1 of 87
ROOFING SYSTEM APPROVAL
Cate2ory:
Roofing
Sub -Category:
Modified Bitumen
Material:
APP/SBS
Deck Type:
Concrete
Maximum Design Pressure:
-635 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions
Specification
Descri tion
All Weather/Empire Base
39 3/R" x 65' 10";
ASTM D 4601,
Asphalt coated, fiberglass reinforced
Sheet
Roll weight: 70 lbs.
Type H
base sheet.
(2 squares)
Flexiglas Base Sheet
39 3/s" x 98'9"; Roll
ASTM D 4601, Type Modified Bitumen coated fiberglass
weight: 901bs.
II
base sheet.
(3 squares)
Flintlastic Base 20
39 3/3" x 49' 6' ; Roll
ASTM D 6163,
Modified Bitumen coated fiberglass
weight: 90 lbs.
Grade S, Type I
base sheet.
(1.5 squares)
Flintglas Ply 4
39 3/8" x 1647'; Roll
ASTM D 2178,
Fiberglass, asphalt impregnated ply
weight: 38 lbs.
Type IV
sheet.
(5 squares)
UL Type G1
Flintglas Premium Ply 6
39 3/8" x 1647'; Roll
ASTM D 2178, Type Fiberglass, asphalt impregnated ply
weight: 40 lbs.
VI
sheet.
(5 squares)
UL Type G1
Flintlastic STA
39 3/8" x 32' 10";
ASTM D 6222,
Smooth surfaced APP Modified
Roll weight: 87 lbs.
Grade S, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GTA
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 105 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GTA-FR
39 3/R" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 105 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 94 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application.
NOA No.: 20-0723.27
MWMkgI M COUNTYExpiration Date: 05/19/23
Approval Date: 09/17/20
Page 2 of 87
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Test
Dimensions Specification
Product
Description
Flintlastic FR-P
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Flintlastic Premium FR-P
39 3/s" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Flintlastic FR Dual Cap
39 3/8" x 32' 10"; Roll
ASTM D 6162,
Granule surfaced SBS modified
weight: 103 lbs.
Grade G, Type II
bitumen membrane with a nonwoven
(1 square)
polyester/fiberglass composite mat
reinforcement for use in cold or mop
applications.
Flintlastic Cap 30
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Granule surfaced SBS Modified
weight: 86 lbs.
Grade G, Type I
Bitumen membrane with fiberglass mat
(1 square)
reinforcement for mop applications.
Flintlastic FR Cap 30
39 3/3" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 861bs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications.
Flintlastic FR Cap 30 T
Flintlastic Base 20 T
39 3/g" x 32' 10' ; Roll
weight: 100 lbs.
(1 square)
39 3/s" x 33'; Roll
Weight: 81 lbs.
(1 square)
ASTM D 6163,
Granule surfaced SBS Modified
Grade G, Type I
Bitumen membrane with fiberglass mat
reinforcement for torch application.
ASTM D 6163,
Modified Bitumen, coated fiberglass
Grade S, Type I
base sheet for torch application.
Flintlastic Ultra Poly SMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Smooth surfaced SBS Modified
Base Sheet
weight: 901bs.
Grade S, Type I
Bitumen Membrane with non -woven
(1 square)
polyester mat reinforcement, for mop or
torched applications.
Glasbase Base Sheet
36" x 98'9"; Roll
ASTM D 4601,
Asphalt coated, fiberglass base sheet.
weight: 75 lbs.
Type II
(3 squares)
Flintlastic Poly SMS Base
39 3/g" x 64' 3"; Roll
ASTM D 4601,
Modified Bitumen coated polyester
Sheet
weight: 90 lbs.
Grade S, Type II
base sheet.
(2 squares)
Yosemite Venting Base Sheet
39 3/s" x 32' 10' ; Roll
ASTM D 3909
Mineral Surfaced fiberglass reinforced
weight: 85 lbs.
ASTM D 4897,
buffer sheet.
(1 square)
Type II
UL G3
NOA No.: 20-0723.27
Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 3 of 87
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Dimensions
Flintlastic APP Base T
39 3/8" x 65' 4"; Roll
weight: 1001bs.
(2 squares)
Flintlastic Ultra Glass SA
39 3/8" x 33'11"; Roll
weight: 73 lbs.
(1 square)
Black DiamondTM Base Sheet
36" x 687'; Roll
weight: 78 lbs.
(2 squares)
Flintlastic SA P1yBase
39 3/8" x 64' 6"; Roll
weight: 86 lbs.
(2 squares)
F1intBond Brush
5 gallon pails
APPROVED INSULATIONS:
Product Name
F1intBoard ISO
F1intBoard ISO Cold
F1intBoardH ISO
F1intBoardH ISO Cold
ACFoam-II
ACFoam-III
ACFoam-IV
H-Shield
H-Shield-CG
DensDeck
Test Product
Specification Description
ASTM D 6509 Modified Bitumen coated fiberglass
base sheet.
ASTM D1970 Self -adhering, fiberglass reinforced,
SBS modified bitumen base/ply sheet.
ASTM D 1970 Self -adhering fiberglass reinforced
ASTM D4601 Type I modified bitumen base sheet
ASTM D 4601,
Grade S, Type II
ASTM D 1970
ASTM D 3019
TABLE 2
Product Description
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Water resistant gypsum board
DensDeck Prime
Water resistant gypsum board
ENRGY 3
Polyisocyanurate foam insulation
ENRGY 3 25 PSI
Polyisocyanurate foam insulation
FescoBoard
Expanded mineral fiber insulation
SECUROCK Gypsum -Fiber Roof Board
Gypsum insulation
DuraBoard
Expanded mineral fiber insulation
Structodek High Density Fiberboard Roof
Wood fiber insulation board
Insulation
APPROVEraAMwldAne
i
Self -adhering, fiberglass reinforced,
SBS modified bitumen base/ply sheet.
Cold applied, SBS polymer modified
asphalt adhesive.
Manufacturer
(With Current NOA
CertainTeed LLC.
CertainTeed LLC.
CertainTeed LLC.
CertainTeed LLC.
Atlas Roofing Corp.
Atlas Roofing Corp.
Atlas Roofing Corp.
Hunter Panels LLC
Hunter Panels LLC
Georgia Pacific Gypsum LLC
Georgia Pacific Gypsum LLC
Johns Manville Corp.
Johns Manville Corp.
Johns Manville Corp.
USG Corp.
Johns Manville Corp.
Blue Ridge Fiberboard, Inc.
NOA No.: 20-0723.27
Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 4 of 87
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description Manufacturer
Mith Current NOA
ISO 95+ GL Polyisocyanurate Insulation Firestone Building Products
Company, LLC
Insulfoam EPS Expanded Polystyrene Insulfoam, a Div. of Carlisle
Const. Materials
APPROVED FASTENERS/ADHESIVES:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions
N'ith Current NOA
1.
Dekfast DF-#14-PH3
Insulation fastener for wood,
various
SFS Group USA, Inc.
steel and concrete decks
2.
Dekfast DF-#15-PH3
Insulation fastener for wood,
various
SFS Group USA, Inc.
steel and concrete decks
3.
Dekfast PLT-H-2-7/8
Galvalume hex stress plate.
2 7/8" x 3 1/4"
SFS Group USA, Inc.
4.
Dekfast PLT-P-R-3
Polypropylene locking plate.
3" x 3 1/4"
SFS Group USA, Inc.
5.
#14 Roofgrip
Insulation fastener
various
OMG, Inc.
6.
ASAP RoofGrip Pre-
Pre -assembled Insulation
various
OMG, Inc.
Assembled System
fastener and plate
7.
3 in. Round Metal Plate
Galvalume AZ50 steel plate
3" round
OMG, Inc.
8.
Dekfast DF-#14-PH3-P3
Pre -assembled Insulation
various
SFS Group USA, Inc.
fastener and plate
9.
Trufast #14 HD Fastener
Insulation fastener for wood and
various
Altenloh, Brinck & Co. U.S.,
steel decks
Inc.
10.
Trufast 3" Metal Insulation
Galvalume AZ50 steel plate
3" round
Altenloh, Brinck & Co. U.S.,
Plate
Inc.
11.
Trufast 2.4" Barbed Metal
Galvalume AZ50 steel plate
2.4" round
Altenloh, Brinck & Co. U.S.,
Seam Plate
Inc.
12.
FlintFast #14
Insulation and membrane
Various
CertainTeed LLC.
fastener
13.
FlintFast 3" Insulation
Galvalume AZ50 steel plate
3" round
CertainTeed LLC.
Plate
14.
Trufast #15 EHD Fastener
Coated carbon steel screw
Various
Altenloh, Brinck & Co. U.S.,
Inc.
15.
Trufast 2" Metal Seam
Galvalume steel stress plate
2" round
Altenloh, Brinck & Co. U.S.,
Plate
Inc.
16.
Dekfast PLT-R-3
Steel, Galvalume AZ50 stress
3" round
SFS Group USA, Inc.
plate for use with all Dekfast
fasteners
NOA No.: 20-0723.27
MiAmFnanE coin Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 5 of 87
APPROVED FASTENERS/ADHESIVES:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions(With
Current NOA)
17.
OMG 3" Galvalume Steel
Galvalume coated steel plate for
3" round
OMG, Inc.
Plate
use with approved fasteners
screw.
18.
3 in. Ribbed Galvalume
Round Galvalume plated steel
3" round
OMG, Inc.
Plate
stress plate with reinforcing ribs
for use with OMG fasteners.
19.
AccuTrac Plate
Galvalume steel plate for use
3" square
OMG, Inc.
with Standard Roofgrip and
Standard Hex Head fasteners.
20.
AccuTrac Flat Bottom
A2-SS aluminized steel plate for
3" square
OMG, Inc.
use with #12 Roofgrip, #14
Roofgrip and #15 Roofgrip.
21.
Flat Bottom Metal Plate
A2-SS aluminized steel plate for
3" square
OMG, Inc.
use with #12, #14 or #15
Roofgrip.
22.
Trufast 3" Recessed Metal
Galvalume steel stress plate for
3" round
Altenloh, Brinck & Co. U.S.,
Insulation Plate
use with Trufast fasteners
Inc.
23.
Trufast 3" TL Insulation
Galvalume steel stress plate for
3" round
Altenloh, Brinck & Co. U.S.,
Plate
use with Trufast TL fasteners
Inc.
24.
F1intFast 2.4" Barbed
Galvalume AZ50 steel plate
2.4" round
CertainTeed LLC.
Seam Plate
25.
F1intFast 3" Recessed
Galvalume steel stress plate for
3" round
CertainTeed LLC.
Insulation Plate
use with F1intFast fasteners
26.
Millennium One Step
Polyurethane two component
See Published
H.B. Fuller Company
Foamable Adhesive
high rise insulation adhesive
Details
27.
Millennium One Step
Polyurethane two component
1.5 liters
H.B. Fuller Company
Green Foamable Adhesive
high rise insulation adhesive
28.
Millennium PG-1 Low
Polyurethane two component
1.5 liters
H.B. Fuller Company
Viscosity Insulation
low rise insulation adhesive
Adhesive
29.
ICP Adhesive CR-20
Polyurethane two component
Two kits (A =
ICP Adhesives & Sealants,
low rise insulation adhesive
401b and B =
Inc.
351b cylinders)
30.
Pliodeck Insulation
Polyurethane one component
See Published
Ashland, Inc.
Adhesive
low VOC adhesive system
Details
31.
Insta Stik Quik Set
Polyurethane one component
It is supplied
The Dow Chemical Company
Insulation
moisture curing adhesive
in pressurized
cylinders with
a net weight of
23 lbs., with a
total unit
weight of 30
lbs.
NOA No.: 20-0723.27
!NG►lMMADE COUNTY Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 6 of 87
APPROVED FASTENERS/ADHESIVES:
TABLE 3
Fastener Product
Product
Manufacturer
Number Name
Descrilition
Dimensions(With
Current NOA
32. OMG OlyBond 500
Spray polyurethane foam
10 gal. bag -in-
OMG, Inc.
Adhesive
insulation adhesive
box set and
1.5 liters
SpotShot
cartridge
33. OMG OlyBond 500 Green
Spray polyurethane foam
10 gal. bag -in-
OMG, Inc.
Adhesive
insulation adhesive
box set and
1.5 liters
SpotShot
cartridge
APPROVED SURFACING/COATING OPTIONS:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions. Any coating, listed
below, used as a surfacing, must be listed within a current NOA.
S� stem. Number Manufacturer Application
1. Generic Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at
60 lbs/sq.
2. Generic Slag applied at 300 lbs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
3. Karnak Corp. Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
4. CertainTeed LLC. F1intCoat A-150 applied at an application rate of 1.5 gal/sq.
5. Gardner Asphalt Corp. APOC #212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
6. Gardner Asphalt Corp. APOC #400 Sunbrite applied at an application rate of 3 gal./sq.
NOA No.: 20-0723.27
Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 7 of 87
EVIDENCE SUBMITTED:
Test A(, encv/Identifier
Name
Report
Date
Factory Mutual Research Corp.
FM 4470
3Y8A1.AM
03/23/96
FM 4470
OD3A3.AM
04/04/97
FM 4470
1D7A4.AM
11/09/98
FM 4470
2DOAO.AM
12/23/98
FM 4470
3023458
07/18/06
FM 4470
3024177
07/18/06
FM 4470
3024311
11/01/06
FM 4470
3031350
09/27/07
FM 4470
3036182
07/31/09
FM 4470
3037127
01/11/10
FM 4470
3039046
06/15/10
FM 4470
3039848
12/02/11
FM 4470
3046104
08/13/13
FM 4470
3048520
09/19/13
Underwriters Laboratories, Inc.
UL 790
R11656
01/11/13
Dynatech Engineering Corp.
TAS 114
3504-12.94-1
10/16/95
United States Testing Company
ASTM D 5147
97-457-2R
12/02/87
ASTM D 5147
97457-4
06/03/88
Momentum Technologies, Inc.
ASTM D 6164
AX31G817
06/05/09
TrinityjERD
TAS 114 (J)
#3504.06.01-1
06/05/01
TAS 114
3521.07.04
07/29/04
TAS 114 (H)
Letter
04/05/06
TAS 117 (B)
3503.10.06
10/10/06
TAS 117 (B)
06490.04.07-R1
06/27/07
TAS 114
3533.01.06-R1
10/26/07
TAS 117 (B) / ASTM D 6862
C8500SC.11.07
11/30/07
TAS 114
C8370.08.08
08/19/08
TAS 117 & TAS 114
C30560.03.10
03/18/10
TAS 117 & TAS 114
C30560.06.10
06/10/10
FM 4474 / TAS 114
C31420.08.10
09/21/10
ASTM D 6164 / D 4798
C31410.01.11-2
01/10/11
TAS 117 B
C35500.02.11
02/09/11
FM 4474 / TAS 114
C37820.07.12
07/24/12
ASTM D1876, TAS 114 (H),
C42110.08.12
08/13/12
TAS 117 (B)
ASTM D 4601
C40050.09.12-1
09/28/12
ASTM D 1970
C40050.09.12-2
09/28/12
ASTM D 5147 / D 4798
C31410.10.10-R1
11/01/12
ASTM D 5147 / D 4798
C31410.01.11-1-R1
11/01/12
ASTM D 4798
C31410.01.11-2A-R1
02/21/13
ASTM D 1876 / TAS 114 (H) /
C44580.07.13
07/25/13
FM 4474
ASTM D 4798
C31410.12.13
12/05/13
NOA No.: 20-0723.27
MAMI-DADE COUNTY
Expiration Date: 05/19/23
Approval
Date: 09/17/20
Page 8 of 87
EVIDENCE SUBMITTED:
Test A-gency/Identifier
Name
Report
Date
ASTM D 6222
C40050.12.13-R1
12/31/13
ASTM D4601
CTR-SC8740.04.15-R2
04/21/15
ASTM D 2178
C47250.03.14
03/26/14
ASTM D 1876, TAS 114 (H),
C45620.03.14
03/27/14
FM 4474
ASTM D 1876, TAS 114 (H),
C47320.03.14-RI
04/01/15
FM 4474
ASTM D 1876
C35460.05.11-R1
05/20/15
FM 4474 / UL1897 / TAS 114 (D)
CTR-SC9935.01.16-RI
01/19/16
FM 4474 / TAS 114 (D)
CTR-SC9175.09.16-1
09/06/16
ASTM D 4601
CTR-SC11145.09.16-
09/19/16
3C
ASTM D 4601-04 (2012), Type II
CTR-SC11145.09.16-
09/19/16
3A
ASTM D 6163
CTR-SC11145.09.16-
09/19/16
5A
ASTM D 6222
CTR-SC11145.09.16-
09/19/16
7A
FM 4474 (B) / TAS 114 (D)
3522.07.04-R1
12/22/16
TAS 114 (D)
CTR-SC15775.10.17
10/31/17
PRI Construction Materials
ASTM D6163
CTC-056-02-01
08/25/10
Technologies LLC
ASTM D 6163
CTC-066-02-01
08/09/11
ASTM D 6222
CTC-071-02-01
08/08/11
ASTM D 6164 / D 4798
CTC-093-02-01
08/09/11
ASTM D 4601
CTC-126-02-01
03/12/12
ASTM D 2178
CTC-123-02-01
03/13/12
ASTM D 6509
CTC-116-02-01
04/04/12
ASTM D 6163
CTC-128-02-01
06/11/12
ASTM D 6163
CTC-129-02-01
06/11/12
ASTM D 6164
CTC-132-02-01
06/11/12
ASTM D 6164
CTC-161-02-01
05/09/13
ASTM D 6162
CTC-183-02-01
10/02/13
ASTM D 6164
CTC-190-02-01
12/02/13
ASTM D 6163
CTC-319-02-01
08/22/17
ASTM D 4601
CTC-321-02-01
08/22/17
ASTM D 1970
CTC-320-02-01
08/28/17
Dynatech Engineering Corp.
TAS 114
3504-12.94-1
10/16/95
NOA No.: 20-0723.27
Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 9 of 87
Membrane Type: SBS Modified
Deck Type 3I: Concrete Decks, Non -Insulated
Deck Description: Min. 2500 psi structural concrete or concrete plank
System Type F(6): Base sheet adhered with approved asphalt.
All General and System Limitations apply.
Note: Concrete deck shall be primed with ASTM D 41 asphalt primer and allowed to dry prior to application of
base sheet.
Base Sheet: One ply of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet,
Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet,
Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the non -insulated substrate with approved
mopping asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or one ply of
Black Diamond Base self -adhered to the non -insulated substrate.
Ply Sheet: One ply of All Weather/Empire Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Glasbase
(Optional) Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20. Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or
one ply of Flintlastic Ultra Poly SMS Base Sheet torch applied or one ply of Black Diamond
Base Sheet or Flintlastic Ultra Glass SA self adhered.
Membrane: One ply of Flintlastic GMS, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic Premium FR-
P, Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 401bs./sq. or Flintlastic FR
Cap 30 T torch adhered to base or ply sheet.
Surfacing:
(Optional)
Maximum Design
Pressure:
APPROVED
Any of the approved surfacing/coating options listed in Table 4.
-635 psf (See General Limitation #9)
NOA No.: 20-0723.27
Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 83 of 87
CONCRETE DECK SYSTEM LIMITATIONS:
1. If mechanical attachment to the structural deck through the lightweight insulating concrete is proposed, a field
withdrawal resistance testing shall be performed to determine equivalent or enhanced fastener patterns and density.
All testing and fastening design shall be in compliance with Testing Application Standard TAS 105 and Roofing
Application Standard RAS 117, calculations shall be signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-401bs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each
side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is
not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application
of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the
fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof
Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from
Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS
117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application
Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer,
Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this
NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 20-0723.27
MAAlF�rY Expiration Date: 05/19/23
Approval Date: 09/17/20
Page 87 of 87