Loading...
HomeMy WebLinkAboutFL-5444-AsphaltRoofingShinglesAPPROVAL NEMO|etc. Certificate of Authorization #32455 353 Christian Street, Unit #13 Oxford, CT 06478 (203) 262-9245 ENGINEER EVALUATE TEST CONSULT CERTIFY EVALUATION REPORT CertainTeed Corporation 20 Moores Road Malvern, PA 19355 (610) 651-5847 Evaluation Report 3532.09.05-R16 FL5444-R15 Date of Issuance: 09/22/2005 Revision 16: 08/14/2019 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code sections noted herein. DESCRIPTION: CertainTeed Asphalt Roof Shingles. LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted herein and FBC 1507.2.7.1 / R905.2.6.1 CONTINUED COMPLIANCE: This Evaluation Report is valid until the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. of any changes to the product(s), the Quality Assurance or the production facility location(s). NEMO|etc. requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words “NEMO|etc. Evaluated” may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 15. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 08/14/2019. This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. NEMO|etc. does not have, nor does it intend to acquire, or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. NEMO|etc. is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing produ cts for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither NEMO|etc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. ©2018, NEMO ETC, LLC NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 2 of 15 ROOFING SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub-Category: Asphalt Shingles Compliance Statement: CertainTeed Asphalt Roof Shingles, as produced by CertainTeed Corporation, have demonstrated compliance with the following sections of the 6th Edition (2017) Florida Building Code and 6th Edition (2017) Florida Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Section Property Standard Year 1507.2.5, R905.2.4 Physical Properties ASTM D3462 2010 1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D3161 2016 1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D7158 2011 3. REFERENCES: Entity Examination Reference Date PRI (TST 5878) ASTM D3161 256T0015 08/12/2019 UL (TST 1740) ASTM D3161 94NK9632 05/15/1998 UL (TST 1740) ASTM D3161 99NK26506 11/23/1999 UL (TST 1740) ASTM D3161 03CA12702 05/27/2003 UL (TST 1740) ASTM D3161 03CA12702 06/16/2003 UL (TST 1740) ASTM D3161 03NK29847 10/03/2003 UL (TST 1740) ASTM D3161 04CA11329 05/24/2004 UL (TST 1740) ASTM D3161 04CA32986 12/03/2004 UL (TST 1740) ASTM D3161 05NK07049 04/15/2005 UL (TST 1740) ASTM D3161 05NK16778 05/12/2005 UL (TST 1740) ASTM D3161 05CA16778 05/12/2005 UL (TST 1740) ASTM D3161 05NK14836 05/22/2005 UL (TST 1740) ASTM D3161 05NK22800 06/22/2005 UL (TST 1740) ASTM D3462 R684 09/21/2005 UL (TST 1740) ASTM D7158 05NK08037 06/28/2006 UL (TST 1740) ASTM D3161 & D3462 09CA28873 07/23/2009 UL (TST 1740) ASTM D3462 10CA41303 10/07/2010 UL (TST 1740) ASTM D3161 10CA41303 10/08/2010 UL (TST 1740) ASTM D7158 10CA41303 10/27/2010 UL (TST 1740) ASTM D3161 & D3462 10CA44960 11/11/2010 UL LLC (TST 9628) ASTM D3161, D3462 & D7158 13CA32897 11/21/2013 UL LLC (TST 9628) ASTM D3161, D3462 TFWZ.R684 04/22/2014 UL LLC (TST 9628) ASTM D7158 TGAH.R684 04/22/2014 UL LLC (TST 9628) ASTM D3161 & D3462 4786334434 09/16/2014 UL LLC (TST 9628) ASTM D3161 & D3462 4786570826 02/12/2015 UL LLC (TST 9628) ASTM D3161 4786821352 02/21/2015 UL LLC (TST 9628) ASTM D3161, D3462 & D7158 4786570717 12/16/2015 UL LLC (TST 9628) ASTM D3161 & D3462 4787195678 02/09/2016 UL LLC (TST 9628) ASTM D3161, D3462 & D7158 4787592174 10/21/2016 UL LLC (TST 9628) ASTM D3161, D3462 & D7158 4787380356 10/26/2016 UL LLC (TST 9628) ASTM D3462 4787380357 10/13/2016 UL LLC (TST 9628) ASTM D7158 4787380357 11/08/2016 UL LLC (TST 9628) ASTM D3161 4787380357 11/09/2016 UL LLC (TST 9628) ASTM D3161, D3462 & D7158 4787586427 01/25/2017 UL LLC (TST 9628) ASTM D3161 & D3462 4788042412 11/15/2017 UL LLC (TST 9628) ASTM D3161, D3462 & D7158 4788362767 03/03/2018 UL LLC (QUA 9625) Quality Control Service Confirmation Exp. 03/09/2020 NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 3 of 15 4. PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 CT20™, XT™ 25, XT™ 30 and XT™ 30 IR are fiberglass reinforced, 3-tab asphalt roof shingles. 4.1.2 Arcadia™, Belmont®, Belmont® IR, Carriage House Shingle®, Grand Manor Shangle®, Landmark™, Landmark™ IR, Landmark™ Pro, Landmark™ Pro Solaris, Landmark™ Premium, Landmark™ TL, Landmark™ Solaris, Landmark™ Solaris IR and Landmark™ Solaris Gold/Platinum are fiberglass reinforced, laminated asphalt roof shingles. 4.1.3 NorthGate™ is a fiberglass reinforced, laminated, SBS modified bitumen roof shingle. 4.1.4 Presidential Shake™, Presidential Shake™ IR, Presidential Shake TL™ and Presidential Solaris™ are fiberglass reinforced, architectural asphalt roof shingles. 4.1.5 Hatteras™, Highland Slate™ and Highland Slate™ IR are fiberglass reinforced, 4-tab asphalt roof shingles. 4.1.6 Patriot™ is a fiberglass reinforced asphalt roof strip-shingle (with no cut-outs) providing a laminated appearance through an intermittent shadow line with contrasting blend drops for color definition. 4.2 Hip & Ridge Shingles: 4.2.1 Presidential Accessory, Accessory for Hatteras, Shangle Ridge™, Shadow Ridge™, Cedar Crest™, Cedar Crest™ IR, NorthGate Ridge and NorthGate Accessory are fiberglass reinforced accessory shingles for hip and ridge installation. 4.3 Accessory Starter Strips: 4.3.1 High-Performance Starter is a starter shingle, measuring 10” x 36”, comprised of a fiber glass mat base and ceramic- coated mineral granules embedded in asphalt. These starter shingles are designed for use with Grand Manor Shangle®, Hatteras™ and Highland Slate™. 4.3.2 Presidential Starter is a starter shingle, measuring 13-1/4” x 40” (overall), comprised of a fiber glass mat base and ceramic-coated mineral granules embedded in asphalt with a reinforcement on its underside (for impact resistance considerations). These starter shingles, applied using two (2) overlapping layers, are designed for use with Presidential Shake™ and Presidential Shake TL™. 4.3.3 Presidential Starter IR is a starter shingle, measuring 13-1/4” x 40” (overall), comprised of a fiber glass mat base and ceramic-coated mineral granules embedded in asphalt. These starter shingles, applied using two (2) overlapping layers, are designed for use with Presidential Shake™ IR. 4.3.4 SwiftStart® Starter Shingle is a starter strip for asphalt roof shingles. Its overall size of 15-1/4” x 38-3/4” yields two (2) 7-5/8” x 38-3/4” starter pieces per shingle. 4.3.5 Universal Starter is a starter shingle, measuring 7” x 36” (overall), comprised of a fiber glass mat base and ceramic- coated mineral granules embedded in asphalt. These starter shingles are designed for use with any CertainTeed shingle measuring 12” x 36” having a weather exposure < 5”. 4.4 Any of the above listed shingles may be produced in AR (algae resistant) versions. 5. LIMITATIONS: 5.1 This is a building code evaluation. Neither NEMO|etc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use within FBC HVHZ jurisdictions. 5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings of this product. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 4 of 15 5.4 Wind Classification: 5.4.1 All shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for us in all wind zones up to Vasd = 150 mph (Vult = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.2 Presidential Accessory, Accessory for Hatteras, Shangle Ridge, Shadow Ridge, Cedar Crest, NorthGate Ridge and NorthGate Accessory hip & ridge shingles have been evaluated in accordance with ASTM D3161, Class F. All except Shadow Ridge (produced in Oxford, NC), NorthGate Ridge and NorthGate Accessory require use of BASF Sonolastic NP 1 adhesive or Henkel PL® Polyurethane Roof & Flashing Sealant, applied as specified in manufacturer's application instructions, for use in wind zones up to Vasd = 150 mph (Vult = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 High-Performance Starter, Presidential Starter, Presidential Starter IR, SwiftStart® Starter Shingle and Universal Starter have been evaluated in accordance with ASTM D3161, Class F. Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3.1 High-Performance Starter shingles are limited to use with Grand Manor Shangle®, Hatteras™ and Highland Slate™ shingles. 5.4.3.2 Presidential Starter shingles must be applied using two (2) overlapping layers and are limited to use with Presidential Shake™ and Presidential Shake TL™ shingles. 5.4.3.3 Presidential Starter IR shingles must be applied using two (2) overlapping layers and are limited to use with Presidential Shake™ IR shingles. 5.4.3.4 Universal Starter shingles are limited to use with CertainTeed shingles measuring 12” x 36” having a weather exposure < 5”. 5.4.4 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.4.4.1 Analysis in accordance with ASTM D7158 indicates the measured uplift resistance (RT) for the CertainTeed asphalt Roof shingles listed in Section 4.1.1 through 4.1.6 (except Presidential Solaris™, Landmark™ Pro Solaris and Landmark™ Solaris Gold/Platinum) exceeds the calculated uplift force (FT) at a maximum design wind speed of Vasd = 150 mph (Vult = 194 mph) for residential buildings located in Exposure D conditions with no topographical variations (flat terrain) having a mean roof height less than or equal to 60 feet. The shingles are permissible under Code for installation in these conditions using the installation procedures detailed in this Evaluation Report and CertainTeed minimum requirements, subject to minimum codified fastening requirements established within any local jurisdiction, which shall take precedence. 5.5 All products in the roof assembly shall have quality assurance audits in accordance with FAC Rule 61G20-3. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 5 of 15 6. INSTALLATION: 6.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle manufacturer’s minimum requirements. 6.1.1 Underlayment shall be acceptable to CertainTeed Corporation and shall hold current Florida Statewide Product Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3. 6.2 Installation of asphalt shingles shall comply with the CertainTeed Corporation current published instructions, using minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or Section R905.2.6 and the minimum requirements herein. 6.2.1 Fasteners shall be in accordance with manufacturer’s published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.2.2 Where the roof slope exceeds 21 units vertical in 12 units horizontal, use the “Steep Slope” directions. 6.3 CertainTeed asphalt shingles are acceptable for use in reroof (tear-off) or recover applications, subject to the limitations set forth in FBC Section 1511 or R908 and CertainTeed published installation instructions. 6.4 HIGH-PERFORMANCE STARTER: 6.4.1 Eaves: For the first starter shingle in each roof corner, use five (5) nails as shown below. All other starter shingles require four (4) nails per shingle. Nails must be of sufficient length to penetrate into the deck 3/4" or through the thickness of the decking, whichever is less. Nails are to be 11 or 12 gauge, corrosion-resistant roofing nails with 3/8" heads. Apply the 10” starter shingle with its factory-applied sealant stripes at the shingle’s lower-most edge and nail firmly into the roof deck as near as possible *(maximum 3”) to the eaves edge while avoiding the sealant. With the starter shingle well fastened to the deck and the sealant low on the starter shingle, it can firmly adhere to the first course shingles. *If nailing within 3” is not possible, nail as closely as possible, then lift and adhere the starter shingle to the underlayment and to the supporting structure with CertainTeed FlintBond™ Asphalt Roofing Cement-Caulk Grade, or approved equal. Rakes: Prior to installation of the field shingles, starter shingles may be applied up the slope along the rake edge with sealant edge placed closest to the rake edge. Fasten as indicated below. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 6 of 15 6.5 PRESIDENTIAL STARTER AND PRESIDENTIAL STARTER IR: 6.5.1 General: These shingles shall be applied by using two (2) overlapping layers. Begin application of the bottom/lower layer of starter shingles by cutting and applying a 13-3/4” x 20” piece at the lower left rake/eaves corner overhanging rakes and eaves 1/4” to 3/4”. Continue along the eaves with full-size 13-1/4” x 40” starter shingles. Each top/upper starter course shingle shall have its 2” top section removed at the perforations, resulting in 11-1/4” x 40” shingles. The colored granule portion of the “top” starter shingles shall be located nearest the lowermost eave edge. Install the first top/upper starter shingle so that it is flush to the left side and bottom edges of the first bottom/lower starter shingle. This first top/upper starter shingle shall be 11-1/4” x 38”. Continue along the eaves with 11-1/4” x 40” top/upper starter shingles ensuring that the lower edges are flush with the lower edges of the bottom/lower layer. Reference the product’s wrapper for more specific details. Eaves: Fasten as shown below. Rakes: After applying the starter shingles at the eaves, but prior to installing the field shingles, starter shingles may be applied up the slope at the rake edge. Fasten as shown below. Fastening: Four nails are required per shingle. Nails shall be of sufficient length to penetrate into the deck 3/4” or through the thickness of the decking, whichever is less. Nails are to be 11 or 12 gauge, corrosion-resistant roofing nails with 3/8” heads. 6.6 UNIVERSAL STARTER: 6.6.1 General: While Universal Starter Strip shingles are specifically designed to be used with shingles 36” length and having a weather exposure of < 5”, they may be installed beneath shingles of any length if special precautions are taken. IMPORTANT: In all cases the end joints of the starter and the first course shingles shall NEVER BE LESS THAN 3-1/2” apart. Eaves: The sealant on starter courses should face out and lie as close as possible to the eaves edge of the roof. Fasten as described below. Rakes: After applying the starter shingles at the eaves, but prior to installing the field shingles, starter shingles may be applied up the slope at the rake edge with sealant facing out and nearest to the outer roof edge. Fasten as described below. Fastening: Use four nails on these starter shingles as shown below. The sealant on starter courses shall lie as close as possible to the eaves edge of the roof. Nails shall be of sufficient length to penetrate into the deck 3/4" or through the thickness of the decking, whichever is less. Nails are to be 11 or 12 gauge, corrosion-resistant roofing nails with 3/8" heads. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 7 of 15 6.7 SWIFTSTART® STARTER SHINGLE: 6.8 CT20™, XT™ 25, XT™ 30, XT™ 30 IR: 6.8.1 Hip & Ridge for CT20™, XT™ 25, XT™ 30, XT™ 30 IR: Cut Shingles 6.8.1.1 For ASTM D3161, Class F performance use BASF “Sonolastic® NP1™” adhesive or Henkel “PL® Polyurethane Roof & Flashing Sealant”, in accordance with CertainTeed requirements. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 8 of 15 6.9 ARCADIA™: 6.9.1 Hip & Ridge for Arcadia™: Cedar Crest™, Cedar Crest™ IR Use two (2), minimum 1¾-inch long fasteners per shingle. For the starter shingle, place fastener 1-inch from each side edge and about 2-inch up from the starter shingle’s exposed butt edge, ensuring minimum ¾-inch embedment into the deck, or full penetration through the deck. For each full Cedar Crest shingle, place fasteners 8-5/8-inch up from its exposed butt edge and 1-inch from each side edge. For ASTM D3161, Class F performance use BASF “Sonolastic® NP1™” adhesive or Henkel “PL® Polyurethane Roof & Flashing Sealant”, in accordance with CertainTeed requirements, to hand-seal Cedar Crest shingles. Apply NP 1 or PL adhesive from the middle of the shingle’s raised overlay on the top piece and extending approximately 4-inch along the sides of the headlap along a line ¾ to 1-inch from each side of the shingle’s headlap. Immediately align and apply the overlying shingle, gently pressing tab sides into the adhesive, and install nails. To secure the other side, apply a 1-inch diameter spot of NP 1 or PL adhesive between the shingle layers. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 9 of 15 6.10 BELMONT® OR BELMONT® IR: 6.10.1 Hip & Ridge for Belmont® or Belmont® IR: 6.10.1.1 Option 1: For Belmont®, refer to instructions herein for Cedar Crest™ or Cedar Crest™ IR hip and ridge shingles. For Belmont® IR, refer to instructions herein for Cedar Crest™ IR hip and ridge shingles. 6.10.1.2 Option 2: For Belmont®: Shangle® Ridge 6.10.1.3 For ASTM D3161, Class F performance use BASF “Sonolastic® NP1™” adhesive or Henkel “PL® Polyurethane Roof & Flashing Sealant”, in accordance with CertainTeed requirements. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 10 of 15 6.11 CARRIAGE HOUSE SHANGLE® AND GRAND MANOR SHANGLE®: 6.11.1 Hip & Ridge for Carriage House Shangle® and Grand Manor Shangle: Refer to instructions herein for Shangle® Ridge hip and ridge shingles 6.12 LANDMARK™, LANDMARK™ IR, LANDMARK™ PRO, LANDMARK™ PRO SOLARIS, LANDMARK™ PREMIUM, LANDMARK™ SOLARIS, LANDMARK™ SOLARIS IR, LANDMARK™ SOLARIS GOLD/PLATINUM OR NORTHGATE: NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 11 of 15 6.12.1 Hip & Ridge for Landmark™, Landmark™ IR, Landmark™ Pro, Landmark™ Pro Solaris, Landmark™ Premium, Landmark™ Solaris, Landmark™ Solaris IR, Landmark™ Solaris Gold/Platinum or NorthGate: 6.12.1.1 Option 1: Shadow Ridge™ or NothGate Accessory Shadow Ridge™ Shadow Ridge™ NorthGate Ridge NorthGate Accessory 6.12.1.2 Optional for Shadow Ridge™ produced in Oxford, NC: For ASTM D3161, Class F performance use BASF “Sonolastic® NP1™” adhesive or Henkel “PL® Polyurethane Roof & Flashing Sealant”, in accordance with CertainTeed requirements. 6.12.1.3 Option 2: Refer to instructions herein for Cedar Crest™, Cedar Crest™ IR hip and ridge shingles. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 12 of 15 6.13 LANDMARK™ TL: 6.13.1 Hip & Ridge for Landmark™ TL: Refer to Option 1 or 2 for Landmark™. 6.14 PRESIDENTIAL SHAKE™, PRESIDENTIAL SHAKE™ IR, PRESIDENTIAL SHAKE TL™, PRESIDENTIAL SOLARIS™: 6.14.1 Hip & Ridge for Presidential Shake™, Presidential Shake™ IR, Presidential Shake TL™, Presidential Solaris™: 6.14.1.1 Option 1: Presidential Accessory 6.14.1.2 For ASTM D3161, Class F performance use BASF “Sonolastic® NP1™” adhesive or Henkel “PL® Polyurethane Roof & Flashing Sealant”, in accordance with CertainTeed requirements. 6.14.1.3 Option 2: Refer to instructions herein for Cedar Crest™, Cedar Crest™ IR hip and ridge shingles. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 13 of 15 6.15 HATTERAS™: 6.15.1 Hip & Ridge for Hatteras™: 6.15.1.1 Option 1: Accessory for Hatteras 6.15.1.2 Option 2: Cut Hatteras Shingles 6.15.1.3 For ASTM D3161, Class F performance use BASF “Sonolastic® NP1™” adhesive or Henkel “PL® Polyurethane Roof & Flashing Sealant”, in accordance with CertainTeed requirements. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 14 of 15 6.16 HIGHLAND SLATE™, HIGHLAND SLATE™ IR: 6.16.1 Hip & Ridge for Highland Slate™, Highland Slate™ IR: Refer to instructions herein for Cedar Crest™, Cedar Crest™ IR or Shangle Ridge™ hip and ridge shingles. 6.17 PATRIOT™: 6.17.1 Hip & Ridge for Patriot™: Refer to instructions herein for Cedar Crest™, Cedar Crest™ IR, Shadow Ridge™, NorthGate or Shangle Ridge™ hip and ridge shingles. NEMO|etc. NEMO ETC, LLC Evaluation Report 3532.09.05-R16 Certificate of Authorization #32455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5444-R15 CertainTeed Asphalt Roof Shingles; (610) 651-5847 Revision 16: 08/14/2019 Page 15 of 15 7. LABELING: 7.1 Each unit shall bear a permanent label with the manufacturer’s name, logo, city, state and logo of the Accredited Quality Assurance Agency noted herein. 7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Table 1507.2.7.1 / R905.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Contact the named QA entity for information on which plants produce products covered by Florida Rule 61G20-3 QA requirements. 10. QUALITY ASSURANCE ENTITY: UL LLC – QUA9625; (414) 248-6409; karen.buchmann@us.ul.com - END OF EVALUATION REPORT -