Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAboutShingle-Owens Corning ShinglesNEMO I etc.
Certificate of Authorization #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203) 262-9245
ENGINEER EVALUATE TEST CONSULT
REPORTEVALUATION
Owens Corning Evaluation Report 037940.02.12-1111
One Owens Corning Parkway FL10674-R16
Toledo, OH 43659 Date of Issuance: 02/06/2012
(740) 404-7829 Revision 11: 12/11/2020
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for
compliance with the 7' Edition (2020) Florida Building Code sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1 / R905.2.6.1
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change.
Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any
changes to the product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a
complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words "NEMO Ietc. Evaluated" may be
displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its
entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 10.
Prepared by:
Robert J.M. Nieminen P.E. The facsimile seal appearing was authorized by Robert
Nieminen, P.E. on 12/11/2020. This does not serve as an
Florida Registration No. 59166, Florida DCA ANE1983 'a .'„ ,` s"'` electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. NEW ETC, LLC does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
©2018 NEMO ETC, LLC
ONEMOJetc.
TABLE 213: WIND CLASSIFICATIONS, STARTER STRIPS AND HIP & RIDGE
Type
Product
FBC Table 1507.2.7.1 or R905.2.6.1
Starter Strips
Starter Strip Shingle
ASTM D3161, Class F
Starter Strip Plus
SRS TopShield Starter
Hip & Ridge
Shingles
Berkshire® Hip and Ridge Shingles with Sealant
ASTM D3161, Class F
DuraRidge® Hip and Ridge Shingles with Sealant
ProEdge®
WeatherGuard' HP Hip and Ridge Shingles
5.5.2 Refer to Owens Corning published information on wind resistance and installation limitations.
5.6 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3.
Refer to the Product Approval of the component manufacturer for components that are produced by a Product
Manufacturer other than the report holder on Page 1 of this Evaluation Report.
6.1 GENERAL:
6.1.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle
manufacturer's minimum requirements.
6.1.2 Underlayment shall be acceptable to the shingle manufacturer and shall hold current Florida Statewide Product
Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3.
6.1.3 Fasteners shall be in accordance with the shingle manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.1.4 Owens Corning asphalt shingles are acceptable for use in reroof (tear -off) or recover applications, subject to the
limitations set forth in FBC Section 1511 or R908 and published installation instructions.
6.2 ACCESSORY STARTERS:
6.2.1 Installation of Starter Strip Shingle, Starter Strip Plus and SRS TopShield Starter shall comply with the Owens
Corning current published instructions, using minimum five (5) nails per strip.
Felt undedayment Deck
Seff-adhered
WeatherLoeke
underlsyment
p_ Drip edge
>e
Nails located
2"-3" tram save
Install first Self-sealing adhesive
Starter Strip positioned along cave
shingle with
6" removed
Starter Strip shingle overhangs eaves and rakes S'i'-8:'
Fek underlaymard
Dmk gWadherad
WcetherLack&
underlayment
Drip edge
Drip
edge
Nais located
_
2"-3" frum esve
instal first starter 5tri Pkrs
p
Seiaealmg adh"ye
positioned along save
with 6"removed
-
Starler Strip Plus overhangs aavas and rakes 114"—VC
Figure 1: Minimum Nailing, Starter Strip Figure 2: Minimum Nailing, Starter Strip Plus
NEMO ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 4 of 10
ONEMOjetc.
6.2.2 Installation of Starter Shingle Roll shall comply with the Owens Corning current published instructions.
Underlayment
Drip edge
Starter Shingle Roll adhered
directly to underlayment and
primed drip edge
Self-sealing adhesive
positioned along eaves
Figure 3: Starter Shingle Roll
6.3 ASPHALT SHINGLES:
6.3.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions:
➢ Berkshire® shingles require minimum five (5) nails per shingle.
➢ WeatherGuard® HP shingles require minimum six (6) nails per shingle.
Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required
Refer to Owens Corning published information on wind resistance and installation limitations.
6.3.1.1 Supreme:
Normal Mansard or Area pare
Wind Areas High Wind desvanes y
Area para vientos normales Areas vientos fuertes
1 rV 2" (B1 1-2" V.
5" Exposure
Exposicion
Figure 4: Minimum Nailing, Supreme
(Standard Size)
Normal Mansard or Area pare
Wind Areas High Wind desvanes y
Area pare vientos normales Areas vientos fvertes
!" W ?
12 t2 t
5 5/8" Exposure
Exposicidn
r1. 2" 1B1 rx. i"�
Figure 5: Minimum Nailing, Supreme
(Metric Size)
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 fH EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 5 of 10
6.3.1.2 Berkshire':
Figure 6: S-Nail Pattern, Berkshire
ONEMOjetc.
Sealant strip
La lira de sellador
8 1d. 8 �h.. L112" $ ��
1
1
Figure 7: 6-Nail Pattern, Berkshire
Sealant strip
La lira de sellador
0 --r —► • • —a r--� •
8 /2' 8112' 81/2'
1
1
2„ Asphalt rooting cement
Cemenlo de Who de astalto
Figure 8: Mansard or Steep Slope Pattern, Berkshire
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 fH EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 6 of 10
NNEMOjetc.
6.3.1.3 Duration® Premium, TruDefinition® Duration, Duration° Premium COOL & TruDefinition® Duration® Designer Color
Collection:
Figure 9: Standard 4-Nail Pattern, Duration
Figure 10: 6-Nail Pattern, Duration
Fastening for Slopes Greater Than 21:12
SureNail® fastening area width
Nail, Typical
!" 12" 12" 1"
�wer�s co�umg surewaa • �� ,r�s euEu,v� sua� • o,.e�� cov,�v� surewa¢® •
6-1l8" 5-518"
exvvsure
Four 1" Spots of Asphalt Roofing Cement
Figure 11: Mansard or Steep Slope Pattern, Duration
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization#32455 fH EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 7 of 10
6.3.1.4 TruDefinitionwOakridge®,Oakridge°:
4 Nail Pattern
Esquema con 4 clavos
5519" Exposure NY
Exposid6nde65/8pulg. Ciavos
Expesicien de 6 6J8 pulg.
Figure 12: Standard 4-Nail Pattern, Oakridge
ONEMOletc.
6 Nail Pattern
Esquema con 6 clavos
�F 12" 12"
Nails
5 519" Exposure Claws 5 518" Exposure
Exposid6n de 66/8pulg. Exposicfun de 56/8pulg.
Figure 13: 6-Nail Pattern, Oakridge
Fastening for Slopes Greater Than 21:12
SureNail® fastening area width
Nail, Typical
1" 12"
Owens comings"rerdaa • •�! a,"s m,�u,"ax"awo •owena corniwg s"reNa;i� •
6-116" 5.518w
exposure
2"
Four V Spots of Asphalt Roofing Cement
Figure 14: Mansard or Steep -Slope Pattern, Oakridge
6.3.1.5 WeatherGuard® HP:
■I��9l2aJg,�l �� �'��
Ysr� Linos
5 518' Exposure 5 5i8' aids
fom,i n de 5 5+6 pui . Expasitifin & 5 5i puig,
Figure 15: 6-Nail Pattern, WeatherGuard HP
6 N all Pattern
Esquema ron 6 davos
5 5+8" Exposure
Exposicun de 5 5,0 ping.
Flail 6 1l8" from bottom
of shingle
Clove a 6 1;8 pulg. de la
6 Fasteners parts inferior do la teja
6 sujetadwes
Four 1" 5po-ts Df Asphaft RDO Cement
Cuatro pantos de cemmeoto de fecl o de itsfaf to de T pulgada
Figure 16: Mansard or Steep -Slope Pattern, WeatherGuard HP
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 8 of 10
NNEMOletc.
6.4 HIP AND RIDGE SHINGLES:
6.4.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions.
➢ Berkshire' Hip and Ridge Shingles with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant require
minimum two (2) nails per shingle.
➢ WeatherGuard® HP Hip and Ridge Shingles and ProEdge° require minimum four (4) nails per shingle.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.4.1.1 Berkshire° Hip and Ridge with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant:
Fig. A
Prevailing Wind Direction
Direccion del viento predominante
Nails p
Clavos '-A
A
4
I I
A
bpi i
r8 Exposure—►{
c&de8pulg
4
A
Figure 17: Isometric View, Berkshire and DuraRidge
6.4.1.2 WeatherGuard' HP Hip and Ridge Shingles:
Fig. A 4 4
Prevailing Wind
Dlrectbn A
A
Nails 4 4
I
A I I
A I I
4 I I
I I
I I
I I I I
s"
Exposure
Fig` B
Top View
Vista superior
Ill 1" 14*
Nail
25/sr� Clavo
I • Owens Coming SureNail' •
I
I+
�I
z
ai
I
I
12"
Figure 18: Plan View, Berkshire and DuraRidge
Fig. C Hip & Ridge Shingle Fastening
To p V lew
Nails Nails
7"
2" 2"
1 " •1
6 Exposure
Figure 19: Isometric View, WeatherGuard HP Hip and Ridge Figure 20: Plan View, WeatherGuard HP Hip and Ridge
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization#32455 fH EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 9 of 10
6.4.1.3 ProEdge®:
Prevailing
Wind Direction SealAnt Strip
A-"'- 8" Exposure
Fasten 711z"
Corer Exposed
Fasteners with
Roof Cement
Figure 21: Isometric View, ProEdge
ONEMOjetc.
Standard —11,
Fastening
Pattern
2"j µ + —2.
7.
12" Sealant
7 +u 6" Exposure
Figure 22: Plan View, ProEdge
As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this
product.
Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements. Refer
to Section 4 herein for products and production locations having met codified material standards.
PRI Construction Materials Technologies, LLC— QUA9110 ; 813 621-5777; bwilson@pricmt.com
- END OF EVALUATION REPORT -
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 fH EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 10 of 10