HomeMy WebLinkAboutAPPROVED POLYGLASSMCOUN
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE OF ACCEPTANCE (NOA
Polyglass USA, Inc.
150 Lyon Drive
Fernley, NV 89408
SCOPE:
MIAMI-DADE COUNTY
PRODUCT CONTROL, SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
www.nuamidade. ovleconom
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Self -Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA# 17-1016.01 and consists of pages 1 through 38.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 1 of 38
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub -Category: Modified Bitumen
Materials SBS/APP/TPO
Deck Type: Wood
Maximum Design Pressure -112.5 psf
TRADE NAMES OF
PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE
1
Test
Product
Product
Dimensions
Specification
Description
Polyanchor
250' x 48"
ASTM D 4601,
A polymer woven, high performance, synthetic base
Type II
sheet.
Polyglass G2 Base
108' x 36"
ASTM D 4601,
Asphalt -coated fiberglass reinforced base sheet
Type I1
Elastoshield HT
65' 8" x 3' 3-3/8"
ASTM D 6162
SBS modified asphalt coated fiberglass/polyester
reinforced base sheet.
XtraFlex SBS HT
65' 8" x 3' 3-3/8"
ASTM D 6162
SBS modified asphalt coated fiberglass/polyester
Base 650
reinforced base sheet.
Elastobase
65' 2" x 3' 3-3/8"
ASTM D 6163,
SBS modified asphalt coated fiberglass reinforced
Type I
base sheet.
Elastoflex SA V
66' 8" x 3' 3 '/s"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
Elastoflex SA V FR
66' 8" x 3' 3-3/8"
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
Elastoflex SA V
66' 8" x 3' 3 3/8"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
PLUS
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
Elastoflex SA V
66' 8" x 3' 3-3/8"
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
PLUS FR
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
XtraFlex SBS Base
66' 8" x Y 3 3(a"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
SA
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
XtraFlex SBS Glass
65' 8" x 3' 3-3/8"
ASTM D 6163,
SBS modified asphalt coated fiberglass reinforced
Base
Type I
base sheet.
Elastobase P
65' 8" x 3' 3-3/8"
ASTM D 6164,
SBS modified asphalt coated polyester reinforced base
Type I
sheet.
Elastoflex SA P
32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
NOA No.: 19-0311.04
MIAMIDADE COUNTY
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 2 of 38
Elastoflex SA P FR 32' 10" x 3' 3-3/8" ASTM D 6164,
Type I
Polyfresko G SBS SA 32' IV x 3' 33/8" ASTM D 61645
Type I
Self -adhered, Fire -rated, polyester reinforced, SBS
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Self -adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self -adhering back face and
a granule top surface.
Polyfresko G SBS SA 3210" x 3' 33/s" ASTM D 6164, Self -adhered, fire -rated, fiberglass reinforced, SBS
FR Type I modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyreflect 32' 10" x 3' 33/s" ASTM D 61645 Self -adhered, polymer, SBS modified bitumen
Type I membrane with a self -adhering back face and a smooth
top surface.
XtraFlex SBS G SA 32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polybond 32' 10" x 3' 3-3/8"
ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Polyflex 32' 10" x 3' 3-3/8"
ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
XtraFlex APP S 32' 10" x 3' 3-3/8"
ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
PolyKool 32' 10" x 3' 33/8"
ASTM D 6222,
Self -adhered, polyester reinforced, APP modified
Type I
bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S 32' 10" x 3' 33/8"
ASTM D 6222,
Self -adhered, polyester reinforced, APP modified
SA
Type I
bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
Polyflex SA P 32' 10" x 3' 33/8"
ASTM D 6222,
Self -adhered, polyester reinforced, APP modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
Polyflex SA P FR 32' 10" x 3' 33/s"
ASTM D 6222,
Self -adhered, fire -rated, polyester reinforced, APP
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyfresko G APP SA 32' 10" x 3' 3 3/8"
ASTM D 6222,
Self -adhered, polyester reinforced, APP modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
Polyfresko G APP SA 32' 10" x 3' 3 3/a"
ASTM D 6222,
Self -adhered, fire -rated, polyester reinforced, APP
FR
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface
XtraFlex APP G SA 32' 10" x 3' 33/8"
ASTM D 6222,
Self -adhered, fire -rated, polyester reinforced, APP
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
NOA No.: 19-0311.04
MIAMMADE COUNTY
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 3 of 38
Polyglass APP Base
65' 8" x 3' 3 3/a"
ASTM D 6509,
APP modified asphalt coated fiberglass reinforced
Type I
base sheet.
PG 100
1, 3, 5, 50, 55
gal,
ASTM D41
A penetrating solution of solvent and a blend of
tube
or 17 oz.
spray
selected asphalts used to promote adhesion.
can
PG 350
1,
3,
5, 50, 55
gal. or
ASTM D3019
A fibered rubberized adhesive designed for use with
tube
Type III
modified bitumen membranes.
PG 400
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use in
tube
ASTM D3409
dry or damp conditions.
PG 425
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use in
tube
ASTM D3409
dry or damp conditions.
PG 450
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement.
tube
PG 500
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use
tube
with modified bitumen membranes.
POLYPLUS 35
1,
3,
5, 50, 55
gal. or
ASTM D3019
A fibered rubberized adhesive designed for use with
tube
Type III
modified bitumen membranes.
POLYPLUS 45
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement.
tube
POLYPLUS 50
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use
tube
with modified bitumen membranes.
XtraFlex 10
1, 3, 5, 50, 55
gal,
ASTM D41
A penetrating solution of solvent and a blend of
tube
or 17 oz.
spray
selected asphalts used to promote adhesion.
can
XtraFlex 35
1,
3,
5, 50, 55
gal. or
ASTM D3019
A fibered rubberized adhesive designed for use with
tube
Type III
modified bitumen membranes.
XtraFlex 50 Premium
1,
3,
5, 50, 55
gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use
Modified Wet/Dry
tube
with modified bitumen membranes.
Cement
WB-3000
5 gallon pail
Proprietary
A low-VOC, water -based acrylic primer to enhance
adhesion of self -adhered membranes.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 4 of 38
APPROVED INSULATIONS:
TABLE 2
Product Name
Product Description
Manufacturer
(With Current NOA)
Polytherm-H
Polyisocyanurate foam insulation
Polyglass USA, Inc.
Polytherm
Polyisocyanurate foam insulation
Polyglass USA, Inc.
Polytherm G
Polyisocyanurate foam insulation
Polyglass USA, Inc.
XtraFlex Polyiso
Polyisocyanurate foam insulation
Polyglass USA, Inc.
XtraFlex Polyiso G
Polyisocyanurate foam insulation
Polyglass USA, Inc.
ACFoam-II
Polyisocyanurate foam insulation
Atlas Roofing Corp
ACFoam-III
Polyisocyanurate foam insulation
Atlas Roofing Corp
Structodek High Density Fiberboard Roof
Wood fiber insulation board
Blue Ridge Fiberboard, Inc.
Insulation
DensDeck, DensDeck Prime
Gypsum insulation board
Georgia-Pacific Gypsum LLC
H-Shield
Polyisocyanurate foam insulation
Hunter Panels, LLC
H-Shield CG
Polyisocyanurate/perlite composite insulation
Hunter Panels, LLC
ENRGY-3
Polyisocyanurate foam insulation
Johns Manville Corp.
Fesco Board
Expanded mineral fiber
Johns Manville Corp.
Multi -Max FA-3
Polyisocyanurate foam insulation
Rmax Operating, LLC.
SECUROCK Gypsum -Fiber Roof Board
Fiber reinforced coverboard
United States Gypsum
Corporation
NOA No.: 19-0311.04
Expiration Date: 10l11l22
Approval Date: 03/21/19
Page 5 of 38
APPROVED FASTENERS:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions (With Current NOA)
1.
Dekfast DF-#12-PH3
Insulation fastener for wood,
SFS Group USA, Inc.
steel and concrete decks
2.
Dekfast DF-#14-PH3
Insulation fastener for wood,
Various SFS Group USA, Inc.
steel and concrete decks
3.
Dekfast DF415-1`1-13
Insulation fastener for wood,
Various SFS Group USA, Inc.
steel and concrete decks
4.
Dekfast PLT-H-2-7/8
Galvalume hex stress plate.
2'/a" x
SFS Group USA, Inc.
3 '/4„
5.
#14 Roofgrip
Insulation and membrane
Various
OMG, Inc.
fastener
6.
Flat Bottom Metal Plate
A2-SS aluminized steel plate
3" square
OMG, Inc.
7.
Trufast #14 HD Fastener
Insulation fastener for steel and
Altenloh, Brinck & Co.
wood decks
U.S., Inc.
8,
Trufast 3" Metal Insulation
Round Galvalume AZ50 steel
3.23 round
Altenloh, Brinck & Co.
Plate
plate
3" round
U.S., Inc.
9,
Polygrip Fasteners #12
Insulation fastener for wood,
Various
Polyglass USA, Inc
steel and concrete decks
10.
Polygrip Fastener #14
Insulation fastener for wood,
Various
Polyglass USA, Inc.
steel and concrete decks
11. Polygrip Fastener #15 Insulation fastener for wood, Various Polyglass USA, Inc.
steel and concrete decks
12.
Polygrip Hex Plates
Galvalume hex stress plate.
" x
Polyglass USA, Inc
3 Y4"
13,
OMG 3 in. Ribbed
Galvalume stress plate.
3" round
OMG, hic.
Galvalume Plate (Flat)
14.
OMG 3" Galvalume Steel
Galvalume stress plate.
3" round
OMG, hic.
Plate
15,
Dekfast PLT-R-3
Galvalume stress plate.
3" round
SFS Group USA,
Inc.
16,
Millennium One -Step
A two component, low rise,
Adco Products, Inc.
dba
Foamable Adhesive
polyurethane foam adhesive
Royal Adhesives
&
Sealants
17,
Millennium One Step Green
A two component, low rise,
Adco Products, Inc.
dba
Foamable Insulation
polyurethane foam adhesive
Royal Adhesives
&
Adhesive
Sealants
18.
Millennium PG-1 Pump
A two component, low rise,
Adco Products, Inc.
dba
Grade Adhesive
polyurethane foam adhesive
Royal Adhesives
&
Sealants
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 6 of 38
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.
Number Product Product Application Specification Manufacturer
Name Description Rate
1, Gravel To be installed in a flood coat 4001bs/sq N/A Generic
of approved asphalt at 60 lbs/sq
2. Slag To be installed in a flood coat 300 lbs/sq N/A Generic
of approved asphalt at 60 lbs/sq
3. KM Acryl 15 A premium white or tinted 1-1 %z gal/sq ASTM D6083 Polyglass USA,
elastomeric acrylic based roof Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
4. KM Acryl 15 QS A premium white or tinted 1-1'/z gal/sq ASTM D6083 Polyglass USA,
quick setting, elastomeric Inc.
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
5. KM Acryl 25 A premium white or tinted 1-1 %z gal/sq ASTM D6083 Polyglass USA,
elastomeric acrylic based roof Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
6. KM Acry125 QS A premium white or tinted 1-1'/z gal/sq ASTM D6083 Polyglass USA,
quick setting, elastomeric Inc.
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
7. KM -PS #220 A single component, solvent, 1.25 gal/sq ASTM D6694 Polyglass USA,
white or tinted, silicone Inc.
coating.
8. KM -PS #250 A premium grade high solids, 1.25 gal/sq ASTM D6694 Polyglass USA,
white or tinted, single Inc.
component, moisture cure,
fluid applied silicone coating
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 7 of 38
APPROVED SURFACING:
TABLE 4
Chosen components
must be applied according to manufacturer's
application instructions.
Number Product
Product
Application
Specification
Manufacturer
Name
Description
Rate
9,
PG 300
An asphalt cutback fibered roof
1'/z-2 gal/sq
ASTM D4479
Polyglass USA,
coating. May be applied by
Inc.
brush or spray equipment to
rejuvenate aged BUR
10,
PG 600
Non-fibered aluminum roof
Y2-1 gal/sq
ASTM D2824
Polyglass USA,
coating.
Type I
Inc.
11,
PG 650
Fibered aluminum roof coating.
1 Yz-2 gal/sq
ASTM D2824
Polyglass USA,
Type III
Inc.
12,
PG 700
A premium white or tinted
1-1 Yz gal/sq
ASTM D6083
Polyglass USA,
elastomeric acrylic based roof
Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
13,
PG 700 QS
A premium white or tinted
1-1 Yz gal/sq
ASTM D6083
Polyglass USA,
quick setting, elastomeric
Inc.
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
14,
PG 800
An asphalt based, non-fibered
3 gal/sq in two
ASTM D 1227
Polyglass USA,
clay emulsion
coats
Inc.
15,
PolyBrite 70
A premium white or tinted
I-1 Y2 gal/sq
ASTM D6083
Polyglass USA,
elastomeric acrylic based roof
Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
16.
PolyBrite 70 QS
A premium white or tinted
1-1'/2 gal/sq
ASTM D6083
Polyglass USA,
quick setting, elastomeric
Inc.
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
17,
PolyBrite 90
A premium grade high solids,
1.25 gal/sq
ASTM D6694
Polyglass USA,
white or tinted, single
Inc.
component, moisture cure,
fluid applied silicone coating
NOA
No.: 19-0311.04
MIAMI DADE COUNTY
Expiration
Date: 10/11/22
Approval
Date: 03/21/19
Page 8 of 38
APPROVED SURFACING:
TABLE 4
Chosen components
must be applied according to
manufacturer's application instructions.
Number Product
Product
Application
Specification
Manufacturer
Name
Description
Rate
18, PolyBrite 95
A single component, white or 1.25 gal/sq
ASTM D6694
Polyglass USA,
tinted, solvent, moisture cure
Inc.
silicone coating.
19. POLYPLUS 60
Non-fibered aluminum roof
/2-1 gal/sq
ASTM D2824
Polyglass USA,
coating.
Type I
Inc.
20.
POLYPLUS 65
Fibered aluminum roof coating.
1'/2-2 gal/sq
ASTM D2824
Polyglass
USA,
Type III
Inc.
21.
XtraFlex 60 Aluminum
Non-fibered aluminum roof
/2-1 gal/sq
ASTM D2824
Polyglass
USA,
Roof Coating
coating.
Type I
Inc.
22.
XtraFlex 65 Aluminum
Fibered aluminum roof coating.
1'/2-2 gal/sq
ASTM D2824
Polyglass
USA,
Roof Coating Fibered
Type III
Inc.
23.
XtraFlex 70 Premium
A premium white or tinted
1-1'/2 gal/sq
ASTM D6083
Polyglass
USA,
Acrylic FR Roof
elastomeric acrylic based roof
Inc.
Coating
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
24.
XtraFlex 80 Emulsion
An asphalt based, non-fibered
3 gal/sq in two
ASTM D 1227
Polyglass
USA,
Roof Coating
clay emulsion
coats
Inc.
25,
XtraFlex 30
An asphalt cutback fibered roof
1 %2-2 gal/sq
ASTM D4479
Polyglass
USA,
Bituminous Roof
coating. May be applied by
Inc.
Coating Fibered
brush or spray equipment to
rejuvenate aged BUR
26,
XtraFlex SRC 8000
A single component, white or
1.25 gal/sq
ASTM D6694
Polyglass
USA,
tinted, solvent, moisture cure
Inc.
silicone coating.
27.
XtraFlex SRC 9600
A premium grade high solids,
1.25 gal/sq
ASTM D6694
Polyglass
USA,
white or tinted, single
Inc.
component, moisture cure,
fluid applied silicone coating
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 9 of 38
EVIDENCE SUBMITTED:
Test Agency
Test Name/Report
Report No.
Date
Factory Mutual Research
4470
2W7A7.AM
08,04,94
Corporation
4450
2D5A9.AM
06,22,99
4470
3000857
01,12,00
4470
3004091
OL12.00
4470
3001334
02.15.00
4470
3014692
08,05,03
4450
3014751
08,27.03
4450
3019317
06,30.04
4470
3024311
ILOL06
4470
3012321
07,29,07
4470
3036182
07.31,09
4470
RR202591
10.22,15
Trinity � ERD TAS 114
11752.09.99-1
02.08.00
TAS 114
11751,05,03
05,30.03
TAS 117(B)-ASTM D903
020841,06.04
06,02,04
TAS 114
02762,03.05
03,30,05
TAS 114
02764,09,05
09,09,05
TAS 114
P1739.01.07
01,23,07
TAS 114
P1734.07.06-R1
02,27,07
TAS 117(13)-ASTM D6862
C8500SC.11.07
11,30,07
TAS 114 & FM 4470
P7860SC.11.07
11,30,07
TAS 114(D) — ASTM D1 876
P10070.10.08
10,09,08
TAS 114(H)
P13760.09.09
09,10,09
FM 4470 & TAS 114
P33970.03.11
03,15,11
ASTM D6163 / ASTM D 4601
P33960.03.11
03,15,11
ASTM D6163
P37590.03.13-2-R1
02,05,13
ASTM D6164
1?37590.03.13-3A
03,06,13
TAS 114
P1738.02.07-R2
04,29,13
TAS 114 & TAS 117 (13)
11757.04.014-R1
04,30,13
ASTMD6509
1?37590.03.13-1-R1
06,26,13
ASTM D6222
P37590.03.13-5-R1
07,01,13
ASTM D6164
P37590.07.13-1
07,02,13
TAS 114 & FM 4474
P41630.08.13
08,06,13
ASTM D4601 / TAS 117
P45940.09.13
09,04,13
ASTM D6222
P37590.09.13
09,12,13
ASTM D4601 / TAS 117
P45970.05.14
05,12.14
ASTMD6162
SC5170.05.15
05,08,15
ASTMD6162
SC5170.12.15-1
12,29,15
TAS 114 & FM 4474
PLYG-SC8905.05.16-1
05,17,16
TAS 114 & TAS 117 (B)
11757.12.00-1-R2
04.05,17
PRI Construction Materials ASTM
D6222
PUSA-061-02-02
01.28.08
Technologies ASTM
D6163
PUSA-064-02-02
02.27.08
ASTM
D6222
PUSA-062-02-02
12,04,08
ASTMD6694
PUSA-134-02-01
05,16,14
NOA No.: 19-0311.04
l;xpiration Date: 10/11/22
Approval Date: 03/21/19
Page 10 of 38
EVIDENCE SUBMITTED:
Test Agencv Test Name/Report Report No. Date
ASTMD6694 PUSA-135-02-01 05,16.14
TAS 117(B) PUSA-202-02-01 05,08.17
FM 4470 & TAS 114 PUSA-202-02-02 05,23.17
NOA No.: 19-0311.04
MIAM4DADE COUNTY Expiration Date: 10/11/22
� � Approval Date: 03/21/19
Page 11 of 38
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type 11: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, Elastoshield FIT, GAFGLAS #75, Polybond* Polyflex*, Polyglass G2
Base, XtraFlex APP S*, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to
the deck as described below:
*with OMG fasteners and Flat Bottom Metal Plates.
Fastening #1: Attach base sheet using 11 ga. annular ring shank and 1-518" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Fastening #2: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-11-2-7/8 plates or Polygrip Fasteners 914 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a
4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft'
Polytherm, Polytherm-H, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-II, ACFoam-III, H-
Shield, Multi -Max FA-3, ENRGY-3
Minimum 1,5" thick N/A N/A
Nate: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 Ibs/100 ft2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Tap Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ftZ
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/" thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the ENT range
and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
NOA No.: 19-0311.04
MIAMIDADE COUNTY Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 12 of 38
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR. Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 13 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, Elastoshield HT, Elastobase P, Polybond, Polyflex, Polyglass G2 Base,
XtraFlex APP S, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck
as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced l2"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation La er O tional
Insulation Fasteners Fastener
Table 3 Density/fe
Polytherm, Polytherm-H, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-II, ACFoam-III, H-
Shield, Multi -Max FA-3, ENRGY-3
Minimum 1" thick N/A N/A
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft'
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/," thick N/A
N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft'. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Primer: Apply WB-3000 at I gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P. Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyrefleet, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
MIAMI•DADECOUNTY NOA No.: 19-0311.04
• • • � � �, >✓xpiration Date: 10/21/22
Approval Date: 03/21/19
Page 14 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: .60 psf; (See general limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 15 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below:
Fastening:
Attach
base sheet
using 11 ga.
Annular ring shank and 1-5/8"
diameter tin
caps spaced 8" o.c.
in a 4"
lap and 8"
o.c. in three
equally spaced staggered rows
in the center
of the sheet.
One of more of the following:
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft2
Polytherm, Polytherm-H, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-II, ACFoam-III, H-
Shield, Multi -Max FA-3, ENRGY-3 QW
Minimum 1" thick
N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 2040 Ibs/100 ft. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Toa Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
Dens Deck, Dens Deck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/a" thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS,
(Optiona►) Elastoflex SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 16 of 38
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA, XtraFlex SBS G SA,
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum
Design
Pressure:
-52.5 psf;
(See
general limitation #7.)
NOA No.: 19-0311.04
MIAMI•DADE COUNTY Expiration Date: 10/11/22
�� � � � Approval Date: 03/21/19
Page 17 of 38
Membrane Type: SBS/APP
Deck Type II: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, Elastoshield HT, Elastobase P XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened as below:
Fastening:
12 ga. Annular
ring shank nails and 1-5/8" tin -caps attached 6" o.c.
in 4" lap and 6" o.c. in four
equally spaced
staggered rows.
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ACFoam-Il, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield,
Polytherm-H, H-Shield CG, Multi -Max FA-3, ENRGY 3
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet with Millennium One -Step Foamable Adhesive,
Millennium One Step Green Foamable Insulation Adhesive or Millennium PG-1 Pump Grade Adhesive applied
over rows of tin -caps in continuous rows 7" o.c. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Primer: Apply WB-3000 at 1 gal. per 300
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SAself-adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum
Design
Pressure:
-60 psf;
(See
general limitation #7.)
MIAMI•DADE COUNTY
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 18 of 38
Membrane Type:
Deck Type 1L•
Deck Description:
System Type
SBS/APP
Wood, Insulated
Min. t9/32 plywood (15/32" for re -roof) or wood plank, fastened at 24" spans with 8d common
nails at 6" o.c.
All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more of the following
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1,0" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Laver
S1;CUROCK Gypsum -Fiber Roof Board
Minimum'/a" thick
DensDeck Prime
Minimum'/a" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
2 with
4
or
15; 10 with 12; 5 1:2 ft2
with
6,
13
or 14; 7 with 8;
2 with 4; 10 with 12; 5 with 1:2 ft�
6 or 14; 7 with 8;
Note: All ►ayers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P FR, Polyflex SA P FR, Polyfresko G APP SA FR, Polyfresko G
SBS SA FR, PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP SA or XtraFlex
SBS G SA self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date; 03/21/19
Page 19 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum
Design
Pressure:
45 psf;
(See General limitation #7.)
NOA No.: 19-0311.04
MIAMI•DADE COUNTY F xpiYation Date: 10/11/22
Approval Date: 03/21/19
Page 20 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type
SBS/APP
Wood, Insulated
19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails or wood
screws at 4" o.c.
All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more of the following
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/
Structodek High Density Fiberboard Roof Insulation
Minimum'/2" thick 2 with 4; 10 with 12 1:1.33 ft2
DensDeck
Minimum''/4" thick 2 with 4; 10 with 12 1:1.33 ft2
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft. to DensDeck prior to application of self -adhered base
(Optional) sheets.
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SAself-adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA, XtraFlex SBS G SA,
self -adhered.
NOA Na.: 19-0311.04
MIAMI•DADE COUNTY Expiration Date: 10/11/22
�� � � � Approval Date: 03/21/19
Page 21 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation #7.)
NOA No.: 19-0311.04
);xpiration Date: 10/Il/22
Approval Date: 03/21/19
Page 22 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C(3):
SBS/APP
Wood, Insulated
11/32 " or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5" thick
Insulation Fasteners Fastener
Table 3 Density/ftz
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Toa Insulation Laver
Structodek High Density Fiberboard Roof Insulation
Minimum %II thick
DensDeck
Minimum''/4" thick
Insulation Fasteners Fastener
Table 3 Density/ft'
2 with 4; 10 with 12 1:1.33 ftz
2 with 4; 10 with 12 1:1.33 ft�
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft. to DensDeck prior to application of self -adhered base
(Optional) sheets.
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 23 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 24 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with wood screws at 6" o.c.
System Type C(4): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following:
Insulation Laver
Insulation Fasteners
Table 3
ENRGY 3, H-Shield, Polytherm-H, ACFoam-II, Polytherm, XtraFlex Polyiso
Minimum 1,5" thick 2 with 4; 7 with 8; 10 with
12
Fastener
Density/ftZ
1:1.33 ftz
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. Tho
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. fl,
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR, XtraFlex SBS Base SA, self -adhered.
PIy Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS,
(Optional) Elastoflex SA V PLUS FR, XtraFlex SBS Base SA, self -adhered.
Membrane: One ply of Elastoflex SAP, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfi•esko
G APP SA, Polyfresko G APP SA FR, Potyfiesko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -82.5 psf; (See General limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 25 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type D(1): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
A11 Genera► and System Limitations apply.
One or more layers of the following
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft'
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick N/A N/A
Top Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft'
Fesco Board
Minimum V thick N/A N/A
Structodek High Density Fiberboard Roof Insulation
Minimum'/2" thick N/A N/A
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/a" thick N/A N/A
Note: Al► insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFlex SBS Glass Base
or XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8 plates, Polygrip Fasteners #14 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a
4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03l21/19
Page 26 of 38
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Resign
Pressure: -52.5 psf; (See General limitation 97)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 27 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with #8 wood
screws at 6" o.c.
System Type D(2): All insulation is loosed laid with
preliminary attachment to deck. Base sheet
is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver
Insulation Fasteners
Fastener
Table 3
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick
N/A
N/A
Top Insulation Laver (Optional)
Insulation Fasteners
Fastener
Table 3
Density/ft2
Fesco Board
Minimum V thick
N/A
N/A
Structodek High Density Fiberboard Roof Insulation
Minimum'/2" thick
N/A
N/A
DensDeek, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/a" thick
N/A
N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach
base sheet using
OAG
414
Roofgrip fasteners and Flat
Bottom Metal Plates spaced 12"
o.c. in
a 4" lap and 12"
o.c. in
two
equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
5A V PLUS FR, XtraFlex SBS Base SA, self -adhered.
NOA No.: 19-0311.04
MIAMI•DADE COUNTY Expiration Date: 10/11/22
C�, � � � Approval Date: 03/21/19
Page 28 of 38
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFtex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf; (See General limitation V.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 29 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type E(1): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet; One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFlex SBS Glass Base
or XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SAP, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General limitation #7.).
MIAMI•DAOE COUNTY
NOA No.: 19-0311.04
• • • • � � Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 30 of 38
Membrane Type:
Deck Type 1:
SBS/APP
Wood, Non -Insulated
Deck Description: 9/32" or greater plywood or wood plank, fastened at 24" spans with 8d ring shank nails at 6"
o.c. at edges and intermediate supports.
System Type E(2): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All Getteral and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglas8 APP Base, XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 sheet fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. annular grooved shank and 1" diameter caps spaced 6" o.c. in a
3" lap and 6" o.c. in four equally spaced staggered center rows.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfi-esko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General Limitation 47)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 31 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" ox
System Type E(3): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply ofElastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFIex SBS Glass Base or
XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgtip fasteners and Flat $ottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
P!y Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General Limitation #7)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 32 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield M . XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 1 I ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
ox. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: 52.5 psi; (See General Limitation #7)
NOA No.: 19-0311.04
Expiration Date: 10/Il/22
Approval Date: 03/21/19
Page 33 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type E(5): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass APP Base, XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 sheet fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8, Polygrip Fasteners #14 with Polygrip Hex Plates or
Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap
and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more
plies
of Elastoflex SA V,
Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS
FR or XtraFlex SBS Base
SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SAP, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum
Design
Pressure:
-60 psi,
(See General limitation
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 34 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. and to blocking
members spaced 48" o.c. with TruFast TP #10x2-7/8" screws spaced 6" o.c.
System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach
base sheet using
12
ga. annular ring shank
nails and
1-5/8" diameter tin caps
spaced 4"
o.c. in
a 4" lap and 4" o.c.
in four equally spaced
staggered
rows in the center of the
sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure:
97.5 psi,
(See
General Limitation #7)
NOA No.: 19-0311.04
MIAMI•DADE COUNTY Expiration Date: 10/11/22
�� • • � � Approval Date: 03/21/19
Page 35 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. and to blocking
members spaced 48" o.c. with #1 Ox3" wood screws spaced 6" o.c.
System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening:
Attach
base
sheet using 12
ga. ring shank
nails and tin caps spaced 4" o.c.
in a 4" lap and 4"
o.c. in
four
equally spaced
staggered rows
in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SAP, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design -97.5 psf; With Elastoflex SA V or Elastoflex SA V FR (See General limitation #7.)
Pressure: -112.5 psf; With all other base sheet options (See General limitation #7.)
NOA No.: 19-0311.04
MIAMI•DADE COUNTY Expiration Date: 10/11/22
C• Approval Date: 03/21/19
Page 36 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 11/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. with #8x3" wood
screws spaced 6" o.c.
System Type E(8): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 12 ga. annular ring sharked nails and 1-5/8" tin -caps 6" o.c. in 4" lap
and 6" o.c. in four equally spaced staggered rows. Tin -caps are primed with PG 100 or
XtraFlex 10,
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Potyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA, XtraFlex SBS G SA,
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design -97.5 psf, With Elastoflex SA V or Elastoflex SA V FR (See General limitation #7.)
Pressure: -112.5 psf; With all other base sheet options (See General limitation V.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 37 of 38
WOOD DECK SYSTEM LIMITATIONS:
A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam
insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using
spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one
at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of 45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 Ibf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf, insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener
spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or
Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 38 of 38