HomeMy WebLinkAboutAPPROVED ROOF CORTEZz
Section A (General Information)
Master Permit No.
Process No.
Contractors Name: e-f AIA_Z;W� r Lt- C- License #1 G CG / Z J7 37
Job Address
ROOF CATEGORY
53 Llw Slope ❑ Mechanically Fastened Tile ElMortar/Adhesive Set Tiles
1 `Asphaltic Shingles ❑ Metal Panel/Shingles ❑Wood Shingles/5hakes
❑ Prescriptive BUR-RAS ISO
ROOF ROOF TYPE_
❑ New roof Repair ❑ Maintenance IV Reroofing ❑ Recovering
ROOF SYSTEM INFORMATION
Low Slope Roof Area (SF) Steep Sloped Roof Area (SF) g d d Total (SF) 1 Z a
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
(— t o ` - +----- 1 (, ` - ---
��0t 3g)
131
F'?4+ r
/W° i✓
In
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component Is not used, identify as "NA")
System Manufacturer: evai' 'J
Product Approval No.:_F1, 16Sy _ IZ Z j O#r
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1': —Zone 1: Zone 2: Zone 3:
Max. Design Pressure, from the specific product approval
system:
Deck: n I
Type: // u/ cvy 0
Gauge Thickness:
Slope:
Anchor/Base Sheet & No. df Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s): S I 1 :9 Ay
Base Sheet Fastener/Bonding Material:
S&/-F~ A1?1+tV/+j6-
Ply Sheet(s)' & No. of Ply(s): I✓ f
Ply Sheet Fastener/Bonding Material:
Top Ply: Ct ) e7 Pt' t'
Top Ply Fastener/Bonding Material:
5 EL r A itf mnft/"�-
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—"
oc @ Lap, # Rows— ® ° Go '
Zone 1:_.._."
oc @ Lap, # Rows ® ° oo '
Zone 2:_"
oc @ Lap, # Rows ® .00 "
Zone 3:_"
oc @ Lap, # Rows_ ® 100
Number of Fasteners Per insulation Board:
Zone 1': Zone 1: Zone 2: Zone 3:
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc.,
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16..
PA
°o FT
Section D (Steep Slope Roof System)
Roof System Manufacturer:
Notice of Acceptance Number:
L
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1: Zone 2e: Zone 2n:_Zone 2r:_Zone 3e: Zone 3r:
Deck Type: c� o o�
Type Underisyment: 3�
Roof SbpW.
f :42
Insulation: N /�
Fire Barrier:
Ridge Ventilation?
1v o
Mean Roof Height:
Fastener Type & Spacing:
I y 2rvCfff+�hL� j
Adhesive Type: /✓ / p¢
Type Cap Sheet: �//'4
Roof Covering. -r6-,yam s
Type & Sips Drip 3 X 3
Edge: