HomeMy WebLinkAboutFL13192_R6_II_2001-14.3 NOA_ Hardie Plank-Panel-SoffitSAE
�
Construction Applied Engineering
Rathisha Sabaratnam, Sr. R&D Technical Services Specialist
James Hardie Building Products, Inc.
10901 Elm Ave.
Fontana, CA 92337
Subject: NOA 20-0730.06 for Compliance with 2020 Florida Building Code (7th Edition)
Dear Rathisha,
8385 White Oak Ave.
Rancho Cucamonga, CA 91730
Phone: 626.409.8650
Project No.: 2001-14.3
Date: December 14, 2020
At your request in reference to the Miami Dade Checklist requirements, based on my review of applicable sections
of the 2020 Florida Building Code and the submitted test reports, it is my professional opinion that the siding products
listed in the attached NOA meet the requirements of the 2020 Florida Building Code.
At your request, based on my review of applicable sections of the 2020 Florida Building Code and the submitted test
reports for the subject products listed in the above referenced NOA, it is my professional opinion that the siding
products listed in the NOA meet the requirements of the 2020 Florida Building Code. Attached are the updated
stamped product installation drawings.
The following are referenced standards in the 2020 FBC:
(1) Wood: AWC NDS-2018 & SDPWS-2015
(2) Structural Design: ASCE 7-16
(3) Concrete: ACI 318-14
(4) Masonry: TMS 402-2016
(5) Structural Steel: AISC 360-16 and 2017 AISC Steel Construction Manual
(6) Cold -formed Steel: AISI 100-16
(7) Aluminum: AA ADM 1-2015
In addition, I make the following Statement of Independence:
(a) I, V. Andrew Tan, do not have nor intend to acquire or will acquire any financial interest in any company
manufacturing or distributing products for which evaluations are issued.
(b) CAE is not owned, operated or controlled by any company manufacturing or distributing products we evaluate
or inspect.
(c) CAE does not have, nor will it acquire financial interest in any company manufacturing or distributing products
for which reports are being issued.
(d) CAE does not have, or will it acquire a financial interest in any other entity involved in the approval process
of the product.
Please feel free to contact me thank you again for your business.
JE IV
Respectfully submitted, -Z� F '.
CAE, Inc. e' No. 81662
e
0e`, STATE OF ,' A//
\
'01YA 1 E1,�,\�
V. A w an, E., exp. 2/28/21
Principal Engineer
Attachments: (1) NOA 20-0730.06
MIAMI. ADE
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.uoy/economy
James Hardie Building Product, Inc.
10901 Elm Avenue
Fontana, CA 92337
SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER-Product
Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction
(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein and has been designed to comply with the Florida Building Code,
including the High Velocity Hurricane Zone.
DESCRIPTION: "Hardie", "Cem" and "Prevail" Planks and Panels Fiber Cement Siding and Soffit
APPROVAL DOCUMENT: Drawing No. PNL, PLK & SOFF, titled "HardiePanel, CemPanel, Prevail
Panel; HardiePlank, CemPlank Prevail Lap Siding; HardieSoffit, CemSoffit Panel; Installation Details
Wood/Metal Stud Construction", sheets 1 through 12 of 12, dated 04/24/2013, prepared by the
manufacturer, signed and sealed by V. Andrew Tan, P.E. on 09/29/2020, bearing the Miami -Dade County
Product Control revision stamp with the Notice of Acceptance number and expiration date by the Miami -
Dade County Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LABELING: A permanent label with the manufacturer's name or logo, Plant City, Florida, and the
following statements: "ASTM C 1186 Type A compliant" and "Miami -Dade County Product Control
Approved" is to be located on each siding plank or panel and per FBC 1710.9.2 and 1710.9.3 on soffit
panels.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA # 17-0821.21 and consists of this page 1 and evidence pages E-1 and E-2, as well
as approval document mentioned above.
The submitted documentation was reviewed by Carlos M. Utrera, P.E.
NOA No. 20-0730.06
49t�� Expiration Date: May 1, 2022
Approval Date: November 12, 2020
Page 1
James Hardie Building Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS NOAs
A. DRAWINGS "Submitted under NOA # 13-0311.07"
1. Drawing No. PNL, PLK & SOFF, titled "HardiePanel, CemPanel, Prevail Panel;
HardiePlank, CemPlank Prevail Lap Siding; HardieSoffit, CemSoffit Panel;
Installation Details Wood/Metal Stud Construction", sheets 1 through 12 of 12, dated
04/24/2013, prepared by the manufacturer, signed and sealed by Ronald I. Ogawa,
P.E.
B. TESTS "Submitted under NOA # 13-0311.07"
1. Test reports on 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
2) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of HardiePlank, HardieSoffit
and HardiePanel, prepared by Intertek Testing Services NA LTD, Test Report No.
100733361COQ-004, dated 08/24/2012, with revision 1 dated 04/25/2013, signed and
sealed by Rick Curkeet, P.E.
"Submitted under NOA # 02-0729.02"
Laboratory Report Test Date Signature
2. ATI-16423-1 PA 202 & 203 03/18/96 A. N. Reeves P.E.
3. ATI 16423-2 PA 202 & 203 03/18/96 A. N. Reeves P.E.
4. ATI 16423-3 PA 202 & 203 03/18/96 A. N. Reeves P.E.
C. CALCULATIONS
1. None.
D. QUALITY ASSURANCE
1. Miami -Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENTS "Submitted under NOA # 15-0122.04"
1. Statement letter of code conformance to the 5th edition (2014) FBC issued by Ronald
I. Ogawa & Associates, Inc., dated 10/26/2014, signed and sealed by Ronald I.
Ogawa, P.E.
4611
Carlos M. Utrera, P.E.
Product Control Examiner
NOA No. 20-0730.06
Expiration Date: May 1, 2022
Approval Date: November 12, 2020
E - 1
James Hardie Building Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
2. NEW EVIDENCE SUBMITTED
A. DRAWINGS
1. Drawing No. PNL, PLK & SOFF, titled "HardiePanel, CemPanel, Prevail Panel;
HardiePlank, CemPlank Prevail Lap Siding; HardieSoffit, CemSoffit Panel; Installation
Details Wood/Metal Stud Construction", sheets 1 through 12 of 12, dated 04/24/2013,
prepared by the manufacturer, signed and sealed by V. Andrew Tan, P.E. on 09/29/2020.
B. TESTS
1. None.
C. CALCULATIONS
1. None.
D. QUALITY ASSURANCE
1. Miami -Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENTS
1. Statement letter of code conformance to the 7th Edition (2020) of the FBC and of no
financial interest issued by Construction Applied Engineering, dated 07/22/2020,
signed and sealed by V. Andrew Tan, P.E.
"Submitted under NOA # 17-0821.21"
2. Statement letter of code conformance to the 6th Edition (2017) FBC and of no financial
interest issued by Ronald I. Ogawa & Associates, Inc., dated 07/30/2017, signed and
sealed by Ronald I. Ogawa, P.E.
Carlos M. Utrera, P.E.
Product Control Examiner
NOA No. 20-0730.06
Expiration Date: May 1, 2022
Approval Date: November 12, 2020
E-2
WALL
HEIGHT
DETAIL A
Jam'
r
t
r
II
I
—WALL LENGTH
Stud Spacing at 16" O.C.
B*-- I I I
JA
"j
y 5
ATE O L14 Z
0 RN
N Al -
Nails at 16" O.C. (typ.)
3/8" Minimum Edge Distance
Sheathing fastener, as described in
Note 1
\ _ Panel fastener, as described in
f ` Note 2
1� HardiePanel, Cempanel,
Prevail Panel Siding
I
Water -resistive barrier per
Florida Building Code Section
1404.2
5/8" thick / 5 ply APA rated
plywood sheathing fastened in
accordance with Florida Building
Code Section 2322.3
2" X 4" S-P-F Wood Studs
The wall and soffit frames are to be designed
by the Architect or Engineer of Record in
compliance with the Florida Building Code.
SEE
DETAIL A
5/8" thick / 5 ply APA rated
plywood sheathing in
accordance with Florida
Building Code Section
2322.3
PRODUCT DESCRIPTION
HardiePanel®, Cempanel®, &
Prevail® Panel Siding materials are
nonasbestos fiber -cement products
tested in accordance with ASTM
C1186 Grade II, Type A and meeting
the requirements of the Florida
Building Code.
PANEL DIMENSIONS
Water -resistive
Width Length Thickness
barrier per Florida
4' 8,9,10' 5/16"
Building Code
GI. Section 1404.2
DESIGN PRESSURE RATING
2" X 4" S-P-F
Installation Design Pressure
Wood Studs
Wood Studs -76 psf
HardiePanel,
Impact Resistant —
SECTION B-B Cempanel,
Planks installed over 5/8" thick / 5 ply
Prevail Panel
APA rated plywood sheathing
Siding
HARDIEPANEL, CEMPANEL. PREVAIL PANEL SIDING INSTALLATION DETAILS
All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's
installation recommendations, and the applicable sections of the Florida Building Code.
Wood studs where HardiePanel, Cempanel, Prevail Panel Siding will be installed shall be
designed by an Engineer or Architect per the Florida Building Code and the requirements of this
N.O.A.
[Note 1] 5/8" thick / 5 ply APA rated plywood sheathing shall be attached to the studs in
accordance with Florida Building Code Section 2322.3.
• The siding panels shall be installed over 5/8" thick / 5 ply APA rated plywood sheathing supported
by a minimum of 2"X4" S-P-F wood studs spaced a maximum of 16" O.C.
[Note 2] The siding panel fastener shall be a 2• long, 0.223" head diameter, 0.092" shank
diameter, corrosion resistant siding nail; the fasteners shall be spaced at 6" O.C. at panel edges
and intermediate studs; the fasteners shall be driven through the 5/8" thick / 5 ply APA rated
plywood sheathing into wood studs located at 16" O.C.
• Fasteners shall have a minimum edge distance of 3/8" and a minimum clearance of 2" from
corners.
HARDIEPANEL, CEMPANEL, PREVAIL PANEL
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901,Elm Avenue
Fontana, CA 92337
P7ne:909-356-6300 SIZE FSCM NO DWG NO REV
9-427-0634TM A PNL-PLK-SOFF 2
Creator: E. Gonzales SCALE 1/2" = 1'-0" Date: 9/29/2020 1 SHEET 1 OF 12
Fastener Spacing per Florida
Building Code Section 2322.3
•
•
6.00in.
Cladding
Framing
Sheathing
FRAMING
• NOMINAL 2" X 4" S-P-F WOOD STUDS 16" O.C. FASTENED
WITH 3-1/2" 16d COMMON NAILS (2 PER TOP AND FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
BOTTOM CONNECTION) NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
• THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHEATHING
• NOMINAL 5/8" THICK / 5 PLY APA RATED PLYWOOD HARDIEPANEL, CEMPANEL, PREVAIL PANEL
SHEATHING FASTENED IN ACCORDANCE WITH FLORIDA INSTALLATION DETAILS WOOD STUD CONSTRUCTION
BUILDNG CODE SECTION 2322.3
CLADDING
■ THE PANEL IS FASTENED WITH 2" LONG, 0.223" HEAD James Hardie Building Products, Inc.
DIAMETER, 0.092" SHANK DIAMETER, CORROSION 10901 Elm Avenue
RESISTANT SIDING NAILS, PLACE NAILS 6" O.C. AT � � Fontana, CA 92337
PANEL EDGES AND INTERMEDIATE STUDS !Phone: 909-356-6300 size FSCM NO DWG NO REV
Fax 909-427-0634 A PNL-PLK-SOFF 2
Creator: E. Gonzales SCALE 1" = 1"-Q" Date: 9/29/2020 SHEET 2 OF 12
WALL LENGTH
Stud Spacing
at 16" O.C.
B
No. 81662: * =!
WALL
HEIGHT•'
I ; STATE O
,
�f
OR1C�,�
,
- -L- - - - -t t —
3/8" Minimum Edge Distance Nails at 6" O.C. (typ.)
DETAIL A
Sheathing fastener, as
described in Note 1
Panel fastener, as described in
Note 2
rI �
1
i
HardiePanel® Siding
Water -resistive barrier per
Florida Building Code Section
1404.2
5/8" thick / 5 ply APA rated
plywood sheathing fastened
to metal studs as described
in Note 1.
20ga, 3-5/8" X 1-5/8" Metal C-stud
The wall and soffit frames are to be designed
by the Architect or Engineer of Record in
compliance with the Florida Building Code.
SEE
DETAIL A
5/8" thick / 5 ply APA rated
. plywood sheathing fastened
4-F
to metal studs as described
in Note 1
Water -resistive
barrier per Florida
Building Code
Section 1404.2
20ga, 3-5/8" X 1-5/8"
Metal C-stud
PRODUCT DESCRIPTION
HardiePanel®, Cempanel®, & Prevail0
Panel Siding materials are nonasbestos
fiber -cement products tested in
accordance with ASTM C1186 Grade II,
Type A and meeting the requirements of
the Florida Building Code.
PANEL DIMENSIONS
Width Length Thickness
4' 8,9,10' 5/16"
DESIGN PRESSURE RATING
Installation Design Pressure
Metal Studs -104 psf
L11 HardiePanel, Impact Resistant —
SECTION B-B Cempanel, Panel installed over 5/8" thick / 5 ply
Prevail Panel APA rated plywood sheathing
Siding
HARDIEPANEL, CEMPANEL, PREVAIL PANEL SIDING INSTALLATION DETAILS
• All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's
installation recommendations, and the applicable sections of the Florida Building Code.
Metal studs where HardiePanel, Cempanel, Prevail Panel Siding will be installed shall be
designed by an Engineer or Architect per the Florida Building Code and the requirements of this
N.O.A.
• [Note 1] 5/8" thick / 5 ply APA rated plywood sheathing shall be attached to metal studs at 6"oc
at panel edges and all intermediate supports using a No.8-18, 0.315" head diameter x 1-1/4" long
bugle head screw
• The siding panels shall be installed over 5/8" thick / 5 ply APA rated plywood sheathing
supported by a minimum 20ga, Nominal 3-5/8" X 1-5/8" Metal C-studs spaced a maximum of 16"
O.C.
[Note 2] The siding panel fastener shall be a minimum No. 8-18, 0.315" head diameter X 1-5/8"
long" ribbed bugle head screw ("or screw shall have at least 3 full threads penetrating metal
framing); the fasteners shall be spaced at 6" O.C. at panel edges and intermediate studs; the
fasteners shall be driven through the 5/8" thick / 5 ply APA rated plywood sheathing into metal
studs located at 16" O.C.
Fasteners shall have a minimum edge distance of 3/8" and a minimum clearance of 2" from
corners.
HARDIEPANEL, CEMPANEL, PREVAIL PANEL
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO REV
Fax 909-427-0634 A PNL-PLK-SOFF 2
Creator: E. Gonzales SCALE 112" = 1'4' Date: 9/29/2020 1 SHEET 3 OF 12
•
• T t!
6.00in.
�76.00in.-
6.00in.
• r
/ Cladding
r
j ,�
ming
Sheathing
•
E W
-- T
�
1•.N.,4�
i
bo
r
_
1
' F
• • • • •
• . • • • • r
•• 0
A
MING
FRANOMINAL
��i
20 GAUGE 3-5/8" X 1-5/8" STEEL STUDS 16" O.C.
lil� \\\\
.��
FASTENED WITH 5/8" WAFER HEAD SCREWS (2 PER TOP
IT
AND BOTTOM CONNECTION)
■ THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
BY THE ARCHITECT OR ENGINEER OF RECORD IN
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHEATHING
• NOMINAL 5/8" THICK / 5 PLY APA RATED PLYWOOD
SHEATHING TO METAL STUDS AT 6" OC AT PANEL
EDGES AND ALL INTERMEDIATE SUPPORTS USING A
HARDIEPANEL, CEMPANEL, PREVAIL PANEL
NO.8-18, 0.315" HEAD DIAMETER X 1-1/4" LONG BUGLE
INSTALLATION DETAILS METAL STUD CONSTRUCTION
(&
HEAD SCREW
CLADDING
■ THE PANEL IS FASTENED WITH NO. 8-18, 0.315" HEAD
James Hardie Building Products, Inc.
DIAMETER X 1-5/8 " LONG CORROSION RESISTANT
10901 Elm Avenue
RIBBED BUGLE HEAD SCREWS (SCREW SHALL HAVE AT
Fontana, CA 92337
LEAST 3 FULL THREADS PENETRATING THE METAL
Phone: 909-356-6300
SIZE
FSCM NO _
DWG NO
REV
FRAMING), PLACE SCREWS 6" O.C. AT PANEL EDGES
Fax 909-427-0634
A
PNL-PLK-SOFF
2
AND INTERMEDIATE STUDS
Creator: E. Gonzales
SCALE 11, = 1'-0"
Date: 9/29/2020
SHEET 4 OF 12
Stud Spacing at 16" O.C.
WALL LENGTH - -� SEE
I
[
----------------------
--
I •
-- ------- ------------
� _
- - - -
I :
- -- --- ---;� -
oMfif
\\
MALL
_
I i
II
:
HT
EIG14
or
•
[
I
[
I
I ,
_1___..___
�I
[ •
, [
[
:1
e
rr
} ilk
: is-i it I ;
fin
B [--- 1
3/4" Minimum Edge Distance Nails at 16" O.C. (typ.)
DETAIL A
Sheathing fastener, as
described in Note 1
_ Siding fastener, as
described in Note 2
1, HardiePlank,
Cemplank, Prevail
Lap Siding
/ Water -resistive barrier
�}— per Florida Building
Code Section 1404.2
5/8" thick / 5 ply APA rated
plywood sheathing fastened
in accordance with Florida
Building Code Section
2322.3
2" X 4" S-P-F Wood Studs
The wall and soffit frames are to be designed
by the Architect or Engineer of Record in
compliance with the Florida Building Code.
DETAIL A
it 5/8" thick / 5 ply APA
rated plywood
_ sheathing in
accordance with
Florida Building Code
Section 2322.3
PRODUCT DESCRIPTION
HardiePlank®, Cemplank®, &
Prevail® Plank Lap Siding materials
are nonasbestos fiber -cement
products tested in accordance with
ASTM C1186 Grade II, Type A and
meeting the requirements of the
Florida Building -Code.
PANEL DIMENSIONS
Water -resistive
Width Length
Thickness
barrier per Florida <9-1/2" 12'
5/16"
Building Code
Section 1404.2
DESIGN PRESSURE
RATING
2" X 4" S-P-F
Installation
Design Pressure
Wood Studs
Wood Studs
-92 psf
Lap Siding Impact Resistant -
C_ Planks installed over 5/8" thick / 5 ply
g_g 1-1/4" tall X 5/16" APA rated plywood sheathing
thick starter strip
HARDIEPLANK. CEMPLANK, PREVAIL LAP SIDING INSTALLATION DETAILS
■ All installation shall be done in conformance with this Notice of Acceptance, the manufacturers
installation recommendations, and the applicable sections of the Florida Building Code.
• Wood studs where HardiePlank, Cemplank, Prevail Lap Siding will be installed shall be designed by an
Engineer or Architect per the Florida Building Code and the requirements of this N.O.A.
• [Note 1] 5/8" thick / 5 ply APA rated plywood sheathing shall be attached to the studs in accordance
with Florida Building Code Section 2322.3.
• Planks shall be applied horizontally commencing from the bottom course of the wall with 1-1/4" wide
laps at the top of the plank such that the exposure area of each plank is <- 8-1/4" vertically.
• [Note 2] The siding fastener shall be a 2-1/2" long, 0.223" head diameter, 0.092" shank diameter,
corrosion -resistant siding nail; The siding is fastened:5 8-1/4" O.C. vertically and 16" O.C. horizontally;
fasteners are driven into wood studs through 5/8" thick / 5 ply APA rated plywood sheathing, fasteners
are placed in the overlapping area approximately 3/4" from the bottom edge of the overlapping plank.
• Vertical joints shall be placed over studs.
• The planks shall be installed over 5/8" thick / 5 ply APA rated plywood sheathing supported by a
minimum of 2"X4" S-P-F wood studs spaced a maximum of 16" O.C.
• Fasteners shall have a minimum edge distance of 3/8".
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm -Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO REV
Fax 909-427-0634 A PNL-PLK-SOFF 2
Creator: E. Gonzales SCALE 112" = 1'-0" Date: 9/29/2020 1 SHEET 5 OF 12
Fastener Spacing per Florida E
Building Code Section 2322.3��
----------- --- _..,-
------ ----------------------------------- _
-
----------- - - ; --------------------
<_8.25in.
FRAMING
• NOMINAL 2" X 4" S-P-F WOOD STUDS 16" O.C. FASTENED
WITH 3-1/2" 16d COMMON NAILS (2 PER TOP AND
BOTTOM CONNECTION)
• THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHEATHING
• NOMINAL 5/8" THICK / 5 PLY APA RATED PLYWOOD
SHEATHING FASTENED IN ACCORDANCE WITH FLORIDA
BUILDING CODE SECTION 2322.3
CLADDING
• PLANKS OVERLAP 1-1/4"
• THE EXPOSURE IS <_8-1/4"
• THE PLANKS ARE FACE NAILED WITH 2-1/2" LONG, 0.223"
HEAD DIAMETER, 0.092" SHANK DIAMETER, CORROSION -
RESISTANT SIDING NAILS, PLACED 3/4" UP FROM THE
BOTTOM EDGE OF THE PLANK AT EACH STUD LOCATION
�--16 in. OC--� Cladding
Framing
I
Fastener Spacing per Florida
Building Code Section 2322.3 If Sheathing
a ■
• ENO, 1 ------------
III
• _ _ fiTA;_F 6F 40 ,rram'..
i E t
rsJ F-ORlO�
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
i
10901 Elm Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO
Fax 909-427-0634 A PNL-PLK-SOFF
Creator: E. Gonzales SCALE 1 = 1 •-0" Date: 9/29/2020 1 SHEET 6 OF 12
REV
2
Stud Spacing at 16" O.C. WALL LENGTH SEE
__I N DETAPL A
Bt-
---------- -- ------ .......---- y , , ------ -- - / 5/8" thick / 5 p PA
•- -- ----- r._
f \\� F3�/}t� r rated plywood y A
sheathing fastened
Z. ,•�� �'NC- to metal studs as
r s ' described in Note 1
WALL
HEIGHT 3 _ Water -resistive
- barrier per Florida
r p�; E OF lrj Building Code
•��
Section 1404.2
20ga. 3-5/8" X 1-5/8"
Metal C-stud
' HardiePlank,
J 1\ Cempiank, Prevail
B F SECTIO \ Lap Siding
3/4" Minimum Edge Distance Nails at 16" O.C. (typ.) B-B 1-1/4" tall X 5/16"
thick starter strip
Sheathing fastener, as
described in Note 1
Siding fastener, as
described in Note 2
i HardiePlank,
Cemplank,
Prevail Lap Siding
Water -resistive
barrier per Florida
Building Code
Section 1404.2
5/8" thick / 5 ply APA rated
plywood sheathing fastened to
metal studs as described in
Note 1
20ga, 3-5/8" X 1-5/8" Metal C-stud
The wall and soffit frames are to be designed
by the Architect or Engineer of Record in
compliance with the Florida Building Code.
PRODUCT DESCRIPTION
HardiePlank®, CemplankO, and
Prevail® Plank Lap Siding materials
are nonasbestos fiber -cement
products tested in accordance with
ASTM C1186 Grade II, Type A and
meeting the requirements of the
Florida Building Code.
PLANK DIMENSIONS
Width Length Thickness
<_ 9-1/2" 12' 5/16"
DESIGN PRESSURE RATING
Installation Design Pressure
Metal Studs -92 psf
Impact Resistant -
Planks installed over 5/8" thick / 5 ply
APA rated plywood sheathing
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING ILLATION DETAILS
■ All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's installation
recommendations, and the applicable sections of the Florida Building Code.
■ Metal studs where HardiePlank, Cemplank, Prevail Lap Siding will be installed shall be designed by an
Engineer or Architect per the Florida Building Code and the requirements of this N.O.A.
[Note 1] 5/8" thick / 5 ply APA rated plywood sheathing shall be attached to metal studs at 6"oc at panel
edges and all intermediate supports using a No.8-18, 0.315" head diameter 1-1/4" long bugle head screw
• Planks shall be applied horizontally commencing from the bottom course of the wall with 1-1/4" wide laps at
the top of the plank such that the exposure area of each plank is <_ 8-1/4" vertically.
• [Note 2] The siding fastener shall be a minimum No. 8-18, 0.315" head diameter X 2-1/4" long" bugle head
screw over metal studs (*or screw shall have at least 3 full threads penetrating metal framing); The siding is
fastened:5 8-1/4" O.C. vertically and 16" O.C. horizontally; fasteners are driven into metal studs through 5/8"
thick / 5 ply APA rated plywood sheathing, fasteners are placed in the overlapping area approximately 3/4"
from the bottom edge of the overlapping plank.
Vertical joints shall be placed over studs.
■ The planks shall be installed over 5/8" thick / 5 ply APA rated plywood sheathing supported by a minimum
20ga, Nominal 3-5/8" X 1-5/8" Metal C-studs spaced a maximum of 16" O.C.
• Fasteners shall have a minimum edge distance of 3/8".
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
77--
Fontana, CA 92337
09-356-6300 SIZE FSCM NO DWG NO REV
9-427-0634A PNL-PLK-SOFF 2
reator: . Gonzales SCALE 1 /2" = 1'-0" Date: 9/29/2020 1 SHEET 7 OF 12
6.00in. �--16 in. OC--� Cladding
6.00in,
Framing
~ F
6.00in.00 , Sheathing
0.751n `
`�.._............... �_._ :........ ........ ------------- ---------- ---------------- • �
58.25in.
FRAMING
■ NOMINAL 20 GAUGE 3-5/8" X 1-5/8" STEEL STUDS 16"
O.C. FASTENED WITH 5/8" LONG RIBBED BUGLE HEAD
SCREWS (2 PER TOP AND BOTTOM CONNECTION)
• THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHEATHING
• NOMINAL 5/8" THICK / 5 PLY APA RATED PLYWOOD
SHEATHING TO METAL STUDS AT 6" OC AT PANEL
EDGES AND ALL INTERMEDIATE SUPPORTS USING A
NO.8-18, 0.315" HEAD DIAMETER X 1-1/4" LONG BUGLE
HEAD SCREW
CLADDING
• PLANKS OVERLAP 1-1/4"
• THE EXPOSURE IS <_ 8-1/4"
• THE PLANKS ARE FASTENED WITH NO. 8-18, 0.315"
HEAD DIAMETER X 2-1/4" LONG CORROSION -
RESISTANT RIBBED BUGLE HEAD SCREWS (SCREW
SHALL HAVE AT LEAST 3 FULL THREADS
PENETRATING THE METAL FRAMING), PLACED 3/4" UP
FROM THE BOTTOM EDGE OF THE PLANK AT EACH
STUD LOCATION
•`
A•
r f'' 1662
-- '2 29 21
OF ,
R 10
AL 0�.�\\�`f 12gf ZD
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GIRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
al) INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO REV
Fax 909-427-0634 A PNL-PLK-SOFF 2
Creator: E. Gonzales SCALE 1" =1'-0" Date: 9/29/2020 ISHEET 8 OF 12
DETAIL A
r
1
a
WALL LENGTH
Stud Spacing at 16" O.C,
B 4---, 1 1 i
I
Nails at 4" O.C. (typ.)
3/8" Minimum Edge Distance
SEE PRODUCT DESCRIPTION
DETAIL A HardieSoffit® & Cemsoffit® materials are
J nonasbestos fiber -cement products tested in
accordance with ASTM C1186 Grade II, Type A
l and meeting the requirements of the Florida
Building Code.
2" X 4" S-P-F SOFFIT DIMENSIONS
Width Length Thickness
Wood Studs 4' 8' 1 /4"
DESIGN PRESSURE RATING
HardieSoffit, Installation Design Pressure
Cemsoffit Wood Studs -70 psf
M
SECTION B-B - �' • ���
ix
,gE OF r� �..
HARDIESOFFIT. CEMSOFFIT PANEL INSTALLATION DETAILS
soffit fastener, as d All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's
escribed in Note 1 installation recommendations, and the applicable sections of the Florida Building Code.
Wood studs where HardieSoffit, Cemsoffit will be installed shall be designed by an Engineer or
Architect per the Florida Building Code and the requirements of this N.O.A.
HardieSoffit, Cemsoffit The soffit shall be installed over minimum 2"X4" S-P-F wood studs spaced a maximum of 16" O.C.
i [Note 1] The soffit fastener shall be a 2" long, 0.223" head diameter, 0.092" shank -diameter,
corrosion resistant siding nail; the fasteners shall be spaced at 4" O.C. at panel edges and
intermediate studs; the fasteners shall be driven into wood studs located at 16" O.C.
Fasteners shall have a minimum edge distance of 3/8" and a minimum clearance of 2" from corners.
Minimum 2" X 4" S-P-F Wood Studs
The wall and soffit frames are to be
designed by the Architect or
Engineer of Record in compliance
with the Florida Building Code.
HARDIESOFFIT, CEMSOFFIT PANEL
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
# 10901 Elm Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO REV
Fax 909-427-0634 A PNL-PLK-SOFF 2
Creator: E. Gonzales SCALE 1 t2" = 1'-0" Date: 9/29/2020 SHEET 9 OF 12
FRAMING
NOMINAL 2" X 4" S-P-F WOOD STUDS 16" O.C. FASTENED
WITH 3-1/2" 16d COMMON NAILS (2 PER TOP AND BOTTOM
CONNECTION)
THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED BY
THE ARCHITECT OR ENGINEER OF RECORD IN COMPLIANCE
WITH THE FLORIDA BUILDING CODE
CLADDING
THE SOFFIT IS FASTENED WITH 2" LONG, 0.223" HEAD
DIAMETER, 0.092" SHANK DIAMETER, CORROSION
RESISTANT SIDING NAILS, PLACE NAILS 4" O.C. AT PANEL
EDGES AND INTERMEDIATE STUDS
16.00in.
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIESOFFIT, CEMSOFFIT PANEL
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO
Fax 909-427-0634 A PNL-PLK-SOFF
Creator: E. Gonzales SCALE V = V-0" Date: 9/29/2020 1 SHEET 10 OF 12
7-0
REV
2
-- --—WALL LENGTH
Stud Spacing at 16" O.C.
B 4-- I I
.
is
I
I
WALL !
HEIGHT I
•i I
i i? i ii
DETAIL A
i
i"
;i
i
�I
Nails at 6" O.C. (typ.)
3/8" Minimum Edge Distance
Soffit fastener, as
described in Note 1
HardieSoffit, Cemsoffit
20ga, 3-5/8" X 1-5/8" Metal C-stud
The wall and soffit frames are to be
designed by the Architect or Engineer
of Record in compliance with the
Florida Building Code.
SEE
PRODUCT DESCRIPTION
DETAIL A
HardieSoffit® & Cemsoffit® materials
are nonasbestos fiber -cement products
tested in accordance with ASTM C1186
' l
Grade II, Type A and meeting the
requirements of the Florida Building
Code.
20ga, 3-5/8" X 1-5/8"
SOFFIT DIMENSIONS
/Metal C-stud
Width Length Thickness
4- 8' '/e"
HardieSoffit,
A,-' Cemsoffit
DESIGN PRESSURE RATING
Installation 4gli n Pressure
Metal S€ud\s��1� 5f
SECTION B-B
No. 81662E
OF
P���\��
LOR10AL
1�111111\
HARDIESOFFIT. CEMSOFFIT PANEL INSTALLATION DETAILS
• All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's
installation recommendations, and the applicable sections of the Florida Building Code.
• Metal studs where HardieSoffit, Cemsoffit will be installed shall be designed by an Engineer or
Architect per the Florida Building Code and the requirements of this N.O.A.
• The soffit shall be installed over minimum 20ga, Nominal 3-5/8" X 1-5/8" Metal C-studs spaced
a maximum of 16" O.C.
• [Note 1] The soffit fastener shall be a minimum No. 8-18, 0.315" head diameter X 1-1/4" long*
ribbed bugle head screw (*or screw shall have at least 3 full threads penetrating metal
framing);the fasteners shall be spaced at 6" O.C. at panel edges and intermediate studs; the
fasteners shall be driven into metal studs located at 16" O.C.
• Fasteners shall have a minimum edge distance of 3/8" and a minimum clearance of 2" from
corners.
HARDIESOFFIT, CEMSOFFIT PANEL
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA 92337
Phone: 909-356-6300 SIZE I FSCM NO
Fax 909-427-0634 A I
Creator: E. Gonzales SCALE 1/2" = V-0"
DWG NO
PNL-PLK-SOFF
Date: 9/29/2020 1 SHEET
11 OF 12
REV
6.00in:� � �16.00in. •ll
6.00in.
^'—'ding
aming
0�0'11liIfJ1}}CC
Ni'
• �
� Via, $166 `�
• • f • • •
• • • • • • • • / '%
$SATE OF lrj
ti
/0NA --
I fr
FRAMING
• NOMINAL 20 GAUGE 3-5/8" X 1-5/8" STEEL STUDS 16" O.C.
FASTENED WITH 5/8" WAFER HEAD SCREWS (2 PER TOP
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
AND BOTTOM CONNECTION)
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
• THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
CLADDING
HARDIESOFFIT, CEMSOFFIT PANEL
THE SOFFIT IS FASTENED WITH NO. 8-18, 0.315" HEAD
INSTALLATION DETAILS METAL STUD CONSTRUCTION
DIAMETER X 1-1/4 " LONG CORROSION RESISTANT RIBBED
BUGLE HEAD SCREWS (SCREW SHALL HAVE AT LEAST 3
111911
FULL THREADS PENETRATING THE METAL FRAMING), PLACE
James Hardie Building Products, Inc.
SCREWS 6" O.C. AT PANEL EDGES AND INTERMEDIATE
10901 Elm Avenue
STUDS
Fontana CA 92337
Phone: 909-356-6300 SIZE FSCM NO DWG NO REV
Fax 909-427-0634 A PNL-PLK-SOFF 9
Creator: E. Gonzales SCALE 1" = 1'-IY' Date: 9/29/2020 1 SHEET 12 OF 12