HomeMy WebLinkAboutAPPROVED JAT EDGE LOC 1'SS-MTS ver 2020MiAMIi•iaAE]E
MIAMI-DADS COUNTY
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES {RER)
PRODUCT CONTROL SECTION
BOARD AND CODE ADMINISTRATION DIVISION
118 05 SW 25 Street, Ronm 208
Miami, Florida 33175-2474
NOTICE OF ACCEPTANCE OA
T (786) 3I5-2590 F (786) 315-2599
n'ww•.nziamidade. a�•leeu�inm
J.A. Taylor Roofing
342 Melton Drive
Fort Pierce, FL. 34982
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami -Dade County) and or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Edge—Loe 1.4: x 16" wide x 24 ga. Steel Panel over Wood Deck
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA-No. 14-0418.0I and consists of pages I through 5.
The submitted documentation was reviewed by Freddy Semino a
MIAMFaAOE COUNTY NOA No.: 18-1023.17
•' ' Expiration Date: 01/09/2024
Approval hate: 12129/2018
Page I of 5
ROOFING ASSEMBLY APPROVAL
Categorv:
Roofing
Sub -Category:
Metal, Panels(Non-Structural)
Materials:
Steel
Deck Type:
Wood
Maximum Design Pressure
—101.00 PSI
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Test Product
Product Dimensions Specifications Description
Edge-Loc 1.0 Length: various TAS 110 Corrosion resistant, prefinished, coated
Width: 16" galvanized, galvalume, standing seam, metal
Height: I" panels.
Thickness 0.02411(24 ga.)
Min. Yield Strength: 50 ksi
Trim Pieces Length: varies N/A
Width: varies
Thickness 0.02411(24 ga.)
EVIDENCE SUBMITTED:
Test Agencv Test Identifier
Valspar 433X515
Valspar 433BI73
Force Engineering & Testing 72-0314T-06A-C
Inc.
Farabaugh Engineering and T158-07A
Testing Inc.
RPPROYED'
Corrosion resistant, prefinished, coated
galvanized, galvalume, standing seam, metal
panels.
Test Name/Report
Date
ASTMB 117
11/21/11
ASTM D 4587, ASTM G 23
11/21/11
TAS 125
03/24/07
TAS 100 04/14/07
NOA No.: 18-1023.17
Expiration Date: 01/092024
Approval Date: 12202018
Page 2 at 5
APPROVED ASSEMBLIES:
System: Edge-Loc 1.0 Panel x 16" Wide X 24 ga. Steel
Deck Type: Wood, Non -Insulated
Deck Description: New Construction 19/32" or greater plywood or wood plank, or for re -roofing 15/32" or
greater plywood.
Slope Range: 2": 12" or greater
Maximum Uplift See Table A below
Deck Attachment:
In accordance with applicable Building Code, but in no case shall it be less than 8d ring
shank nails spaced 6" o.c. In reroofing where the deck is less than 19/32" thick (Minimum
15/32") The above attachment method must be in addition to existing attachment.
Underlayment:
Minimum underlayment shall be an ASTM D 226 Type II installed with a minimum 4"
side -lap and 6" end -laps. Underlayment shall be fastened with corrosion resistant tin -caps
and 12 gauge 1 '/4" annular ring -shank nails, spaced 6" o.c. at all laps and two staggered
rows 12" o.c. in the field of the roll. Or, any approved underlayment having a current NOA.
Fire Barrier Board:
Any approved fire barrier having a current NOA. Refer to a current fire directory listing for
fire ratings of this roofing system assembly as well as the location of the fire barrier within
the assembly. See Limitation # 1.
Valleys:
Valley construction shall be in compliance with Roofing Application Standard RAS 133
and with PAC Contractors Association's current published installation instructions.
Metal Panels and
Install the "Edge-Loc LO Panel" and accessories in compliance with the current published
Accessories:
installation instructions and details in PAC Contractors Association's Installation Manual.
Flashings, penetrations, valley construction and other details shall be constructed in
compliance with Roofing Application Standard RAS 133.
Panels shall be secured at a spacing listed below in Table A with corrosion resistant # 10-13
x 1" pancake head screws of sufficient length to penetrate through the sheathing a minimum
'/m of an inch.
The adjacent panel shall overlap and be secured to each other when The female rib of panel
is snapped over the male rib of panel.
TABLE A
MAXIMUM DESIGN PRESSURES
Roof Areas
Field Perimeter and Corner'
Maximum Design Pressures
—59.75 psf—101.00 psf
Maximum Screw Spacing
16" o.c. 6.75" o.c.
I. E olazion shall not be allowed
NOA No.: 18-1023.17
Expiration Date: O1/092024
Approval Date: 12/202018
Page 3 of 5
SYSTEM LIMITATIONS
I. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. The maximum designed pressure listed herein shall be applicable to all roof pressure zones (i.e. field, perimeters,
and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced
pressure zones (i.e. perimeters, extended comers and comers).
3. Panels may be rolls formed in continuous lengths from eave to ridge. Maximum lengths shall be as described in
Roofing Application Standard RAS 133.
4. All panels shall be permanently labeled with the manufacturer's name and/or logo, city, state, and the following
statement: "Miami -Dade County Product Control Approved" or with the Miami -Dade County Product Control
Seal as seen below. All clips shall be permanently labeled with the manufacturer's name and/or logo, and/or
model.
MIAWDADE COUNTY
I.....1 1
5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
6. Panels may be shop orjobsite roll formed with machine models #'s 5521095 and 7031100 from PAC Contractors
Association.
MiAMronoe COUNTY NOA No.: 18-1023.17
Expiration Date: 01/09/2024
Approval Date: 12/20/2018
Page 4 of 5
PROFILE DRAWINGS
Fastener Relief, Stiffening Ribs and Striations are Optional
Field Condition
EDGE-LOC 1.0 PANEL SYSTEM
END OF THIS ACCEPTANCE
M III iowoecouMrr NOA No.: 18-1023.17
V=4 Expiration Date: 01109/2024
Approval Date: 12/20/2018
Page 5 of 5
:,IProfessional
Regulation
B�
Mile— ,gin UfN PL91a4a11M XIX2Nm 4,'
=LMMt Sur[ryrrtg aIBb81Mh Pudl[Bta[.s Confatt Vs aCI55NC Maa �n15
t s.arcn
d*r
uproOR� IAprproval
9apP.yyscyyt s AFFYI[atlan agli
FL*
Appliwtlon Type FL5259-R31
Code Varslon ReWslon
APPIIcation Status 2020
Appravad
Com mmui
Amhlved
Pmdud Manufacturer
Addrlas/Phone/Email POLYGLASS tl5A
1111 W. Newport Cen(!r Dr,a
DeenFeld Beach, FL 33492
(954)Z13-13M Ea1:242
malpert@potyglass.cam
Authorized Signature
Maury A pert
malpertppolygiass.cam
technical Representa0re
AddnoWphone/Email TECH REP
1111 West Newport Center Drive
Dinarfle(WG) aid Black, FL 33442
(868)802-e011
u5polygiassteclmicai®polyglass.cam
Qualtyy Asaumxe RepresentatNe QA REP
AtltlresajPhor�e/Email 1111 West Newport Center Drive
Deerfield Beach, FL 33442
(888)410-1325
uapolyglasstechnkalglpplygbsssom
Category Raclin,Subcategory
wwenaym rota
compliance Metaod
Evaluation Report from a Flontla Registlretl ArtlRact ar a 4
Professional Engineer aansetl FlorMa
Evaluatlon Report - Hardcapy Recelvetl
Fh nda Engineer ar Architect Name who Evaluaton Report tlevelopetl Ne Robert Nieminen
Honda Licence Quality Assurance Entity PE M-543-59166
Quality Assurance Cantnact Expi,anum Date UL ILLC 022
Valldatad By
1Mn W. "anceinch, PE
Vagtlallon Checklist - Hardmpy Receivetl
Cemcate of lndeperbence FL522 Rai CQI 2D 0 01 DI t
Reflrenced StaMarL and Year (of Stallard) standaw
ASTM D1970
226
Tear
ASiM D26 2015
A:TM D4298 2009
AST! M163 2011
ASTM D6164 2015
A 14 D6222 2011
ASTM 06509 2011
2015
Equivalence of Product StandaMs
Certified By
S-Rion from the Code
Product Approval Method
Daze Submitted
Date valkated
Date Pending FBC Approval
Date Approved
Date Rnvhed
'i.. ruf NPdaf. Number ar
Nema
�5259.1 Polyglass Roof
UMeliaymants
Umfh si, Us.
O"Mved for use In WH2: No
—
Approved for use oulslds WH, Yes
Impact RPaista" N/A
dams. Pressure: +N/A/-B22.5
OHISI 1.) The design pressure In Nis 1 M1
epp1100110n relates Pe one Parbculaf
undedayment system for use in file roof ' E
systems. Refer tq ER Section 5.83 far other
ayatems and associated maximum deal'.
pressures. 2.) R to ER Section S fur
other limits or use.
FM 4474
FRSAM SIMh Edition
UL 1897
mathod 1 oVtbn 0
10/22/2020
10/26/2020
11/01/2020
12/15/2020
12/21/2020
underlaymenls
veHfied By: Robert Nleminen PE-59166
Created by Independent TRIM Party: yes
by Independent TM Party: Yes
Beall O
1HI--:: ]Nlr __
1M sbu ofr ds IS en WV empbye w Z_ZglI - -
-- 5� irMeev e_a-bo ..
9Mtle Nn.aMll etltlmssm'are wWamew. �_...__..
S.. Me
a...P.. tM pudic To Petemla
premes Pop sampu:
®0®Eq®
Credit Card
Sete
2011
2018
2015
Nmo ( etc.
cwtyKoreolAudnn'ratiwi ag2a55
353 Christian Street, UnR #13
Oxford, CT 06478
ENGINEER EVALUATE (203)262-9245
TEST CONSULT
Polyglass USA Int ME
1111 West Newport Center Drive Evaluation Report P12060.02.09-R27
Deerfield Beach, FL 33442 FL5259-R31
(95 t) M2330 Date of Issuance; 02/24/2009
SCOPE: Revision 27:09/30/2020
This Evaluation Report Is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by by Robert Nieminen, P.E. for
use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described
herein have been evaluated for compliance with the r Edition (2020) Florida Building Code sections noted herein.
DESDUPTION: Polyglass Roof Undedayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein and
FBC 1507.1.1.
CONTINUED COMPUANrt: This Evaluation Report is valid until such time as the named Product(s) changes, the referenced Quality
Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change. Acceptance of our
Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any changes to the product(s), the
QualityAssurance or the production facility location(s). NEMO ETC, LLC requires a complete review of its Evaluation Report relative
to updated Code requirements with each Code Cycle.
AD MMEMEMt The Florida Product Approval Number (FLU) preceded by the words'NEMO)etc. Evaluated" may be displayed in
advertising literature, If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a COPY Of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the lob site at the request of the Building Official,
This Evaluation Report consists Of pages 1 through 17.
Prepared by:
A
P° v''"
Robert J.M. Neminen, P.E.
;'a;a'", r4:
Florida Replstmtian No. 59166, Florida nrA
NEM3 Yw°;;,',„`..+ magwmue ae+iawndnaweseunwaed aaanuiem
C[NIIfNXTIpI Of lNpapENpeynr: n9i3011aM il,li 6xino[rerveu anelerpmeal Nm'F'E on
Naisnmd:unknl.
1. NEMO ETC, LLC does not have, nor tloes It intend to acquire or will
products it luates. isna
acquire, a findal Interest In -W company manufacturing or distributing
eva
2. NEW ETC, LLC Is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nleminen, P.E. does not have nor will acquire, a financial Interest in any company manufacturing or distributing products for which the
evaluation reporM are being issued.
t. Robert Nieninen, P.E. does nothave, nor will acquire a financial interest in any other entity invoked in the approval process fthe product.
i. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminsn, P.E. are, in any way, the Designer of Record for any project on
W ach this Evaluation Report, or previous sermons thereof, isjwas used for permitting or design gukance unless retained spedflcally for that
purpose.
C2a19NEMOErc,u,c
ONEMOJetc.
....,... weego': Roofing
Sub -Category: Underlayment
Compliance Statement: Roo{ Underlayments, as produced by Polyglass USA, Inc, have demonstrated compliance with the
following sections of the 7D EdRlon (2020) Florida euRiling Cade through testing in accordance with the following Standards.
Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein,
1504.3.1
Wind resistance
FM 4474
Tear
1507.1,1/R905.11
Wind resistance
UL
189]
2011
2015
3507,1.1, 1507.2.4,1501.2.9.2 /
Material standard
ASfi1
D226
2009
R905.1.1, R905.2.8.2
Material standard
ASTM
D1970
2035
1507.33/R905.3.3
Material standard
1S07.1L2/R9dS,11.2
Material standard
FRSA/TRI, Sixth Edftian
2018
1507.11.2/ R905,11.2
Material standard
ASTM
M163
2015
1507.11.2/agoS,11.2
Material standard
ATM
D6164
2011
150].11.2/905.11.2
Material standard
ASTM
06222
2011
TA5130
ASTM
Accelerated Weatherin
D009
20 15
g ASTM
D4]98
201211
ERD W6p49) Wind UPlift
EPDnYT
1I757.0801.1
OB/Li/SIX13
FROITST6D49)
balkaft
6 ift Wind UPlift
1177606.02
Oljl6/2Po3
30/90dmIWa
PLYGSC119m.0m
ERDDSTfi049) WIM UpIiN
P3740.01.U]
01/W/200I
ERD RST EOf9I
Tessin
PLYGSC]2115.DB.1)
OR/09/1017
ERD(TSTfi049) ASTMD1970
P5130. XD74
ERO G5T fi009)
TA5103
PtVG-5[13035.0g.17
30/31/2017
FRD(TSTM49) Wind UPMt
P92Eom"
MI/200)
03/L1/2Cq
FM(RT iB-)
WIM Up"n
30pg0y1
Gull/)N3
6POjT5T6049) Wind Upl{R
p{a540.11.09-RS
NxF51Vt2396
( )
IBCCwnPtlartce
ESR-169)
O>p](2019
ROMT6049) TemileAgHeslon
P11030.]1.041
1l/�/zage
1130/2L09
HVHI C°:nplDone
ROW, 17-0614.22
0]/051201)
M OST6049) Wind Uplift
P31030.11.09-2
1]/3(Y2a9
Mn DyT 2y13)
mil
ASTM p479g
DUCH)A
01/01/Np6
ERDjTST'6049) 0.5TM 049))
P31D3DIL09-3
]j oes
FISr6pl9)
pSTM Ol9T1
4PLYGS6004.03.38
ERp ((STan49) A51M p19)0
P333W.0a.10
O6/35/3010
HgMp DSTE049)
WMtl UPIIft
44PLYG-YBf.A3.0].]9
OV11/20"
ERD (TST rods) TAS 103
P33370.03.11
011
0OGA011
NEr.M1 nsf Edge)
AttM D6]63
4SPlYG-]&W2,p3.1,yA
m/U/3039
RD(TsT6049) hmlle0tlhealan
P333mA411
NFMp(RT6049)
ASR4 D6I2Z
4SPLYGSB-0pip5.19{
OS(30/2019
ER)((STE049) ASTM DI9)0
Fq0
%)ap0.1p.11
10/]9/ZOii
N MO (19T 6pgg)
TA5303��
Q-PLYG14sw01.00A
Y9/t0(2019
iT5T60{9) iA5103
P40390AR.12�1
OB/M/3033
NFW (TST6049)
ANLYG-fecW']0'19G
]0/OB/im9
ERDf15TE049) Tenyk MM1esron
ERDMT60691
Po0390.08]22
OB/0)/2ml
NEMpIr5T dogs)
TA5103
i0.t
4 FLTG16009.10.141
10/80019
Tionle Adhesion
C41420.M.1A3
09JY1/1012
NfMp IT$T6g91
163
4Si YGASDEN.10.ul
ip(pg/202g
ERD ITSTE0491 WNd Uplift
P396Bp.p3.13
NEMOIT5T6p491
TAS 303
TA52oe
41 MTG-1455U0101A
31L130/i039
Efl0(15T dogs) ASIM DI9M
P410(3.04.YT
3.
04/60/2013
/S6/30]3
4LPlYG.1 6AM.1213F
32/1812019
ERD(f5T6045) Wind UPMt
P17AW.W-RE
DM3a/2013
NEWp TEW91
NEMO(19T60491
TA5103
ASTM
4J-PLYG-1935VDLMA
OL02/2m0
Ean IT3Tgl Wintl UpliN
01(30(2013
NEMO �fi0991
DI9X�
45'PLTG-I8iO4.01.204
EROMT5019) AFUM 06164
P3]590.03.1i3A
05 /06/2013
ASTM Ol9M
45AYG-]8-004.01.20.N
01/14/20I0
D1114YZOZO
RO DST60491 ASTM 06509
P3759pM.33-1A O6/owing
NEMp MT6099)
TA5103
4SPLTG-1B000.0130A
OU1612WO
RD(3TT6049) Wind Uplft
R1610.01113
OR/p8/1U13
NEMO (RT 60491
l5TM o616q
4SPLYG 18-0040120.8
OM26/2020
ERDRST6049 ASIM D4fip1
P4RIODR,.23
GWD412013
NEMO UST 6069)
ASTMD6222
4YRYG-1R00x3239i4U
O 1/%(Z020
ERO lti'W49I
( ) Wintl UqM
P11751.M.03-R1
1L26/2W3
NEMpiT57,,D
TA5103
PLYGSC15R55A5,20A
03/19(low
RD(W 60491 Wind Uplih
%ll83.31A3R1
11%!6/1p33
pEMO Usr 6of
NEW (r5T 6M9)
TA5103
41-PLM2o%UOLa1
07/06)Ip20
30i90 Padhesio
PA92)0,05.14
05/3wom
NEMUM7gM9)
ASIM W22
ARM
41 p.YG3956MB osA
m/23/1020
RD(T31'6D49)
RD(T3TED49) Tensileadhesion
6020,09.14-5
03/Og/2014
NFMODST6019)
04 799/DS613
"mM
41S1Y6-1T59WL-0S.p
O9(10/20M1
R0DST60491 Tenslleatlhesim
6020.09.14E
M/0O3//2Z014
WVUW9)
019M
TA9103
"sni-SOSS xca'A
09/30nol0
ERD nnrE049) Tensile atlM1eLon
Po6920.30.19
NE014
(TST6949)
TAS
4i-PLYGI =,,,S.0
O9/d0/MN
to
4J-PLYG20d5UDL-13
m/30j2020
NEMa ETC, LtC
rert(RmrssfAvMWAoNm M2es9
7n'RM N 120201 FBC NONdNHZ EVALUATION
fYaivation Report p12060,02.09.1[27
PeF)glay RoO(UMkriAymerd3
F13259 Rai
Revision 27: 09/30/2020
Page 2 of 17
oft
MN&IM
Eal)(W1049)
MTMa191oA,n98
Rai
P43290.10.14
21H
10/I1F[014
Am
ERD DSTfi0491
TastesPLYG.aCRs0.D3.15
W/z4/zols
I'm p5TSB18)
Efla (i9T6pp4)
TmHkatlM1eslan
PW390.00.15
04/ai/N16
nil tr6T5878)
ERn I$r ease)
TAs 103
PH36D10.14A1
Dfi/WQIS
PRI jrST 58JB1
MITST68r8)
ERD pSr60I91
ERD(m6049)
word Upm
AMW D1970
PLVGSLe%s.OSla1
PRIITS 58711)
6M9)
Ego
TenNkatlM1eNOn
PLY63C30sXaa.1G1
NYG-SC10130.063f-t
I/11/JD16
%/JJ/2ou
D0.1 ST 58J
n 111)
ER DST
TAs 109
D6/D/EDS6
Paint- usa
fWard9)
ERD pirmd9/
ASTM039m/0a198
ttTGSC10ll0.06.163
ERDm Tfi%9)
Mad UP8n
PLYGS<ax&a,J.16
007/16/3zois
UL(�A%�
En pSr 8M91
TASus
MYG-SC12025.10.16
Iw12/2016
Ut(QUA%zs)
PtYGSC130,Q3236
Iz/Jr/2016
M(QDAssa)
4.1
Product
ElasWbase
4.2
Elastobase P
4.3
Elastoflex S6G
4.4 Elastofiex SISG FR
4.5 HydraGuard Dual pro
4.6 1 HydraGuard Tile Pro
4.7 Mule -Hide SA-APPCap Sheet
4.8 MUle-Hide SA-APPCap Sheet
(FR)
4.9 Polyfiex G
4.10 1 Polyflex G FR
4.11
PolyFlex SAP
4.12
Polyflex SAPFR
4.13
Palyglasseasy
4.14
Polyglass G2 Rase!
Material5tandard I Plmt(s
ASTM D6163
FL
ASTM D6164
FL
ASTM D6164
Fl, PA
FRSA/TR109-18
ASTM D6164
FL
FRSA/TRI D9-18
ASTM 01970
FL
ASTM 01970
FL
FRSA)TR109-18
A6TM 06222
fL
fR5Af1'RI09-38
ASTM b6222
FL
FRSA/fR109-IB
ASTM 06222
FL
FRSA/tAl M-Is
ASTM D6222
FRSA/TRl09-18
FL
FL, TX
FL, TX
FL
kmojetc.
tombNm TertWe Rgo
Mhtsbn PR10111 WOW=
TM 103 NM18$-m W/14/2Wa
TA3 to PUsxasa 41 09/19/20%
TAs 1W PUS1-0Ssa2.02 11/30/3%r
MTM Dew PUSA.06142p2 01/28/Jtl18
ASTM D6164 PUS14ga0241 07729/2003
P/L AMaW[ Muk-HWe Goa, Lig p3/p1/[0Qq
M--*A(CdaeR P0lyatld`cOmpwntl 08/18/zoil
Qwllty ccmrol servile COnflmeNpn{tt) 09/13/z018
Quality Ca.' 3ervi,e CwlRrmrtlon px) S1f%(1019
Quality Central NMda ens current
Description
RS modified
base
raane4lsr-remrorcea, S115 modified bitumen cap sheet
Nominal 60tnil thick dual -layer rubberised asphalt
waterproofing membrane, fiberglass reinforced, with a
Polyester fabric surface
Nominal 60-m11 thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
Polyester fabric surface
Polyester4einforced, APP modified bitumen cap sheet
Polyester -reinforced, APP modified bitumen cap sheet
use as an alternate to Heat ApPiled'Up Sheet" in the
"Two Ply system" from FRSA/TRI F/odda Hlgh LAW
Concrete and pay Roof 7i1, Inrtullatton Manual, Sixth
Edition beneath mechanically fastened or adhered the
roof systems
Polyester -reinforced, APP modified bitumen cap sheet fi
use as an alternate to Heat Applied "Cap Sheet" in the
"Two Ply system" from FRSA/TRI Florida High Wind
Concrete and Gay RoofTBe Installation Manual, Sixth
Edition beneath mechanically fastened the roof systems
Polyester -reinforced, APP modified bitumen cap sheet
Poh es er-reinforced. APP modifled bitumen cap afleat
Hbergless-reinfDrced, APP modified bitumen base sheet
W Warc, LM
Unylmk lAar4mW11onr32186 Jai MMON (2az0) MC NON-NWIZ EVALUATION Gaeastbn RaPart Plz0fiea249-a27
PRlygkv RooFUrWe4wmenir FL5259-R31
Reyhlan 27:09/3D/2020
Page 3 of 1J
ONEMOjej
Product r Matadal Standard Ward{a)
4.15 Polysdck IR-%e q$TM D1970 Dessattkm
Ft, PA, 7X Nominal 10-mil thickrubberized asphaltwaterp�ng
membrane, an fiber reinforced, with an aggregate
15 Pp surface
lystick NITS plus ASTM D1970 FL, NV, Nominal 60-mil thick rubberized asphalt waterproofing
FRSA/7RI 09-1g PA, TX membrane, glass fiber reinforced, surfaced with
4.17 Polystick MU-X Polyolafinic film surface
ASTM D297W FL, NV, PA Nominal 54-m11 thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
4.18 Potysdck 7U Max poWpropylene Rim Surface
ASTM D1970 FL, PA, TX Nominal60-mil thick rubberized asphalt waterproofing
FRSA/iRi 09-18 membrenewith a 190 g/m' polyester fabric surface
4.19 PolysOck TUP FRSA/TR109-IB FL, pq, 7% Nominal 130-1101 thick rubberized asphalt uvaterproogng
membrane, glass-fiber/polyester reinforced, with a
4.20 Polystirk TU Plus granularsurface
ASTM D1970 FL, Pk TX Nominal 80-mil thick rubberized asphalt waterproofing
membrane, membrane, glass fiber reinforced, with a polyester fabric
4.21 Potystick%Ffl surface
ASTM D3970 NV, TX Nominal 80-mil thick rubberized asphalt waterproofing
FRSA/TRI O9-18 membrane, glass fiber reinforced, surfaced with
5.1 This is a Building Code Evaluation. Neither NEMD ETC, LLC rwr Robert Nleminen, P.E.are, in any way, the DesignerofRecerdfor
any project On which this Evaluation Report, Or previous versions thereof, k/was used for permitting
retained specifically forthat purpose. Or design guidance unless
5.2 This Evaluation Report is not for use In FBC High Velocity Hurricane Zone Jurisdictions (Le, Broward and Miami -Dade Counties).
5.3 This Evaluation Report pertains to above -deck roof components, Roof decks and structural members shall be in accordance with
FBC requirements to the satisfaction of the Authority Having Jurisdiction.
5.4 This Evaluation Report does not include evaluation of fire classification. Refer to FBC 1505 for requirements and limitations
regaMingroofassembiyfimciassinution. Referto MC26M for requirements and limitations concemingthe use Offoam plastic
Insulation.
5.5 POlyglass Roof Undedayments may be used with any prepared roof cover where the product is specifically referenced within
FBC approval documents. If not listed, a request may be made to the Authority Having Jurisdiction for approval based on this
evaluation combined with supporting data for the prepared roof covering.
' PPrysrisAaW-Iraac been7Pu,w though <mnp4roHwtesting tv W. vlesser<aefi4Y<M IlrlrtMrttlmm ASSMOaaarov/hp fAln a 4rymMiDm, festMa[s1PrMPN
b6oretwy<v„pidw,s. A9/Rmentbefweun Wr<AaseranOttaw,os.tttlorfhm5tttlon4.3, Notel PjasrM 014T6154h4uypaesePWlshMas ro.taP,<sisiPM'G
NEMD Eft. HC.
hNJ/<ute ulauNmiirvtnn,r3a455 7'�EDmaN(z02oIF0CNOKHWZWAtUAM,N Eu4luatgn RePen PSta60y2.0941ZT
PPiyglnxa4af Utkar14ym4Ma iLSl59-Ra1
aeviwba2T:09/30/2020
Pagt4 of lT
5.6 Allowable RDof C ve
AVW
a+wv�b
cmwee9nle
U11dMeymMt
UAW.
D W4
NtedgNut
AdhetlYe-
Pam
Alrech
Sp
Ilse:
E>s[ebite
Y.
Ye]
Ye:
ab
OxMrgeq
rya
smsa�
1
Wa.ma..L
Pn�,
+saaa3l
m]b,ry
Elastobase p
Yes
Yes
Yea
ye.
INIwNeb
hsY45N11.
W4.e9neM1
lanna
oaq rao.q
wsbal
m.sn91
one.h
PolyRlass Base
Yes
Yes
we..slmo,
bso-N
No
=s611
fu5A3
Pdy IM GZ Base
Yes
Yq
No
NveamsW
basNAet,
No
Smeb9J
5r
ElastoRex 56G
No
Yea
Eiaztoilex 56 G FR
Meese.
No
No
Yet
No
No
HYdreGuard Dual Pro
y„
No
Ya
HydmGuard Tile Pro
Y.
Yet
T.
Isaes.e.L
Yea
Mule -Hide SA-APPcap Sheet
No
Yea
Ycs
Oaes.6.11
No
Mule -Hide SA-APP[ap Sheet(FR)
No
Y.
Yee
Isses aq
No
PolyflexG
No
Y.
Yea
PelyRexG FR
ISee S.&D
No
No
yes
No
No
'... PolyHex SA p
No
vet
Yes
Ilea s.e.11
No
PONfkx MP FR
xo
Yes
Yes
Sb U
No
Polyakk 1114,
Y.
No
No
Ne
POIYttkk MTS PWs
Yc
Yes
No
Yes
Polysddt MU.X
Y.
Nu
No
Yr
Palynirk TU Mex
No
Yee
Yes
Cke 5.9.O
Yes
PoWck TUP
No
Ya
yes
(See sb.l)
NO
Polysflck TU Pkxs
Yea
Yes
Yes
(Sxi6.11
Yee
P0110"ck XFR
vas
Yet
Ne
Yes
NBMDEf itc
NNEMOjetc,
Mehl
shrteor
3; Tyq
Wood
ShNkiea
Shkytes
!tlpAdJ
p9Wry
NRInske
ShdNapsm.N
Yes
Yea
YN
Yea
Nbmma V'
e o]r
d6nMbb
oxxb, gseq
NRe�Vbm ofiq
NRm.nbDYty.
y ef
s
es
_ rteelp
M.
221, ,o
] Dxx6. rvey Yl
INWmab
Ole Tty.11l
y
b ��
Yes
�mm VEM'
)Ip pl
rN.w
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
NO
Yea
Yet
Yn
Y.
9sa�temm,]wx.l.Lx
B.uimbsvmr.iu
/asoe.u31
/gm.vs31
Yea
yes
Vei
Yes
Bam%NM W1.1L3
Bm��NiPfi 1501113
Jatm3.Lp
/ypsa.W
No
No
No
No
no
No
No
No
No
No
No
No
No
No
No
ft
No
No
No
Ne
No
No
No
No
No
Yea
Yee
Yes
BNmarW 190la.La
BpmsyryfWae
/wu.131
luvs
Yes
Yes
vea
BHnbpo]w].LLI
Ya
QynI vby16O111 .
/P905,L
/RMSSfq
Yea
Yea
Y°'°
Yea
—a
IUIIfyLi.ly011!
lws.ull
lasusix
Y.
Yes
No
Y°a
Y.
0^h] arLaa0.1.13
tdn[np ..LL]
/M19MS.l-rl
/a9h.11a
No
yes
Yes
WMnnM4f oa s
Cglom eo,
1feO11q
/MMo..)
Yea
Yev
Yes
Yes
BM]IDp•IYI31➢
pae41aki 35O.113
/M3.Ll.a1
/OJs.
'.. You
Yes
Yes
n.x.............
Yes
...... .___..
RrMou°olAUNwbabI R2655 TTM EDITION 120211l FBC NON.WH2 WAtUAnON EYalaa0M RBPEN Pl2060.02.093127
P°NRlan Roof Undedaylnems f15259 R31
Revision 27:0913012020
Page 5 of 17
5.6.1 Adhesive -set tile is limited to use of the following underlayment/tile-adhesive combinations.
POlystltk TU Max or PWystick TU plus
HydraGuerd Tile Pro, Was SA p. Pr
Elastofiex S6 G,HYd roGu¢rd Tik Pm, MulHWe M-APP C P Sheet M111Hide 6A-
APPCap sheet (FR), PWyflex G, Pulyflex SA
naneove-
P, POIVHex SA P FR, Polysdck TU Max,
Pnlystkk M P or Poiystick TU Plus
10 Adhaswa and Sextants
ePolyseN
Elestaflex 56 G, HydraGuard Tile Pro, Mule
Aµ-16D•
-Hide SA-APP Cap Sheet, Mule-HWe SA-
'..APPCap Sheet (FR), Palyflex G, POO" $A P, Was, SA P FR, pWCP
Potys &TU Porp ystidtTV Max,M
olyatkk TU Plus
Adhesives and Sealants
"Polyset•
RTA-I'
57 Allowable Substrates:
TABIE2: SUM MTE0mONSFORADHEREDUfgIERuyMkN15
Und.dayineM
AppllrMim
Substrates idesigned to meet wind Wash
Hydra6uard Dual Pro,
TYR
Primer
Hyd raGuard Tile Pro, P-fWkk IS.
Deck (
Optional) ASTM
plywood, 058, Southern
ge, Potysdck NITS Plus, Pplystick
sheathing
Woods "ZIP System"P
MU-x, PolystickTU Max,
ASTM 091
stract.ral oonuete
PolWtick TUP Poiyatlrk TU PI
self-
ONEMOjetc.
FL14506
FL22S25
FL6332
FL62T6
PONStkk)(FR, Mule -Hide SA-APP
adhering
Implanter,(OPUonal)ASTM
ASTMC1289Typ¢NgasslpoMwcyamFrate, ASTM
CAP Sheet, Mule-NIde SA.App
D41 Pr WBd000
C1289 Type v poh/Isaclianurrate-camposRe, DensDeck
Cep Sheet (Fill, potytlex SAP a
Pdme or SECUROCR GyPsum-Fiber Roof Board
PohyHex SA P FR
Base Sheet
N/A
AS , Type ll felt Elastobase, Elastobau P or Mule-
..
Hidea Nail Nail ease
Elastoikx 56 G or Elastogex M G I Insulation (0p
FR hot asphalt D41
Base Sheet N/A
PolyRexGor Polyflex G FR torch- Imulatlon tW
applied D41
Base Sheet I N/A
DensDeck Prime Or SECUROCR Gypsum -Fiber Roof Board
ASTM 0226, Type II FWL Elastobase, ElatoMs¢ P, Mule-
HWeNail Base-0.1v .. . n_-_
Deno Prime or SECUROCK Gypsum -Fiber Roof Board
EgstotMu, Elastobase P, Mule-Hfde Nail Base. Pnlvel_
t Referto 771e Manufacture6 orAdhesive Manufaaum, FloNda product Approval for o"numina Moment Reststantt Performance,
NEMO ETC, Uc
rertl/tr+r°�'Wta°nYONm pa26iS TTM M'T*N(MMI FM NON-HVHZ EVALUATION EvaluatWR Rupert P13060.O R2T
Potyplass RaeFOndedaymants FUi259-M2
ReWfion 27! M/W/2p2a
Page 6 °f 1T
SA Attachment Urnitatio • NNEMOletc.
SAA For use under mechanically attached NON -TILE prepared root coverings, attachment shall be in accordance with the
manufacturer's installation instructions, but - for mechanically attached undedayments or base sheets - not less than FBC
1507.1.1 or 11905.1.1.
5.8.2 For use under tile roof systems, attachment shall be In accordance with the m nnufactumes installation Instructions, but -
for mechanically attached base sheets - not less than:
• FRSA/TRI Florida High Wind Concrete and Clay RoofT"'chuta#ation Manua{Sixth Edition, AppendixA,Table l(forTwo-
Ply Asphalt Applied Hot Mop Undedayment)
or
5.8.3
• Section5.8.3 herein (for other undedayment systems).
Wind Resistance for Ondelvm t Sish'EM In Tile Rciaf Ao,lications,
The following wind upidt H-H atmns apply to undedayment systems that are not prescriptive in the FR
Wind Concrete and Clay Roof Die Installation Manual, Sixth Edition. The Maximum Design Pressure is the reslult of tesorida ting
for wind load resistance based on allowable wind loads, and reflects the ultimate Passing pressure divided by 2 (the 2 to 1
margin of safety per FBC 1504.9 has already been applied).
5.8.3.1 AltCLAo-Deck;
The maximum design pressure for the selected assembly shall meet or exceed that required under FRSA/TRI Florida High
Wind Concrete and Clay Roof Tile Installation Manuel, Sixth Edition, Appendix A, Table IA or the critical (highest) design
Pressure determined in accordance with FBC 1609 or FBC Residential Chapter 3.
41 Maximum De i e pressor 52.5 oaf;
Deck: APAdictio]/I6 CAT,a.4la iO'Exposure 1,053sheathingto meetprolett1wEMIementSmsa[isfattlon ofAuth0fty Having
ludsdittlon.
Jolm: Min. flinch wide stops of Elastaflex5A-V over all Me joints
Base Ply: Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide M APP Cap Sheet, MUIe-Hide SA-APP Cap Sheet (FR), PWlex SA p, polyflex SA P FR, Pollotick TU Max, PDIYAIck
TU P or Polysl TU Plus, self -adhered.
#2 Maximum Design Press - 90 sed.
De*: Sum 15/32-inch plywood to meet project requirements to Satisfaction of Authority Having JurisdkUon.
Primer: None
Base Ply: (Optlonall Patystick MTS Plus, self -adhered.
Underlaymem, Mule -Hide SA-APP Cap Sheet, MUIe-Hide SA-APP Cap Sheet (FR), PolygexM P, Pattez SA p FR, Polystick TU Max, PONSH
TU P or PoNstick TU Plus, sag -adhered.
#3 Nli�innum Design Pr - 75 pg
Deck: Min.15/32tnM pty d to meet protect requirements to satisfaction of Authority Having Jureclak,o
Primer: PGIOUar A5TMNI
Use Ply: (OPdiva,l) PcIntick Mrs Plus, selfadhennt
Under6aymem: Mule -Hide SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet (FR), Pdyflex SA P, Polyflex SA P FR. Polystck T.)Max, Polystick
TU P or Polystick TU plus, self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x Ito' ring shank
nails through 32 ga., I-5/V diameter On caps spaced 12-Inch o.c.
44 Maximum Design Pressure - 105 asf
Deck: Min.15/32-inch plywood to meet Project requirements to satisfaction of Authority Having Jurisdiction.
Primer. wB-3000
Base Ply: (Optional) Polystick NITS Plus, self -adhered.
Unde"ment Mule -Hide SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet iFRI, POlyflex SA P, Polyflex SA P FR, PoNgick TU Max, Polystick
TU P or Polystick TU Plus, selfadhered and back -nailed within the selvedgectlge side laps using 12 ga. x IV ring shank
nails through 32 ga.,1-5/8" diameter tin raps spared 12-inch a.c.
MEMO Em, Lie
hrtfimN yaurho,aonon a37sss 7' EDITOR(1020) FBC NON -Hers E,ALUATON Cwhiatbn RBPOM P1sOE0.02.09-BD
Polyzies Roof undwayiewu FL5258-R31
Revlabn 27: 09/30/20sa
Page 7 a 17
N5 Maximum DeSAV Pressure 13 f; kilfiojetc.
Deck: Min. 15/32-Inch plywood to meet
Primer: Project requhemenu
(Optional) PGIDO or ASFM to satisfattion of Authority Having JurlsdiRlon. Base Ply: (Optional) Poly4ick MTS plus
, self -adhered.
lolnfr. Min. cinch wide Strips of Elastagex SA-V ever all
Ints
Underaymenb Mule -Hide SA-APP up Sheet, Mule -Hide SA- pp$�)
P APP Cap Sheet (FR), Polyflex SA P, Po TV P Or Polystick TV Plus, self -adhered. PVfllx SA P FR, POlystick TV Max, Polystick
46 MEnifluln Design P 315 sF.
Deck: Structural concrete to meet project requirements to satisfaction of Author Haring
Haying
Primer: PGIMor ASTMJurisdiction.D41
Base Ply: (OptlOnai) Polystick MTS Plus, self-adhered.Underlayment Hydm6.ard Tile Pro, Mule -Hide M-App Cap Sheet, Mule -Hide SA-App Cap Sheet (FR), Polyflex M P, Polyfiex M P PH,
POlysdrk TU Max, Polystick TV P or Polystick TV plus, self -adhered.
g7 Maximum D I P ssu -622 5 sL•
De°k: structural concrete to meet roect requirement to satisfaction Of Author) Navi Prmer. PGIOD or ASTM D41 p 1 q N ng Jurisdiction.
Undedayment ElaatoRex S6 G, applied in full mopping of hot asphalt or polynex G, torch -applied.
g8 All other direct -deck, adhered underlaymentsystems beneath the mofsystems carry a Maximum Design Pressure of-45 psf.
5.8.3.2 Mechanical"H shed Base
The maximum design pressure for the selected assembly shall meet or exceed that required under FRSA/TRI Fonda High
Wind Concrete and Clay Roof Tile Installation Manual, Sigh Edition, Appendix A, Table lA or the critical (highest) design
Pressure determined in accordance with F13C 1609 or FBC Residential Chapter 3.
Alternatively, the maximum design pressure far the selected assembly shall meet or exceed at least the Zone 1 design
pressure determined in accordance with FIIC 1609 or FRC Residential Chapter 3. Elevated pressure zones shall employ an
attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used
methods are ANSI/SPRI WDl, FM Loss Prevention Data Sheet 1-29, Roofing Application Standard RAS 117 and Roofing
Application Standard RA5137. Assemblies marked with an asterisk' carry the limitations set forth in Sectlon 2.2.10.1 Of FM
Loss Prevention Data Sheet 1-29 (February 2020) for enhancements,
49 Max"mum Devon Pressure 30 0
Deck: Min.15/324nch OSB to meet PrOJett requirements to satisfaction of Author)
Base Sheet Elastobse or Mule -Hide Nall Base(poty-film top surface) NHaving lurlsdiNon.
Fasteners: 1193. x 1.25-inch long x 1-Inch head diameter round metal cap nails
spacing: 6-inch O.. atthe 3-Inch wide side Lapland 6-inch o.c. at two (2) equally spaced staggered canter rows.
aria Ply: (Optional) Polvatkk MTS Plus, self -adhered.
Underlayment Mule -Hide SA-APP tap Sheet, Mub-Hlde SA-APP Cap sheet (FR), Polyf ex SA P, Polyflex 5,4 P FR, PolysNck TV Max, POlystick
TV P or Polystick TV Plus, Self -adhered.
#10 Maximum Dilisign "Slim
Deck: Min.15/324mh plywood to meet project requirements to Satisfaction of Authority Having Jurodictim.
Base Sheet: Elastobase or Mula Jlde Nail Base (poly -film top surface)
Fasteners: 11 ga. x 1.25-inch long 1-inch head diameter round metal rap nails
Spacing: 6-inch o.c, at the 34nch wide side laps and 64nch u.c. at two (2) equally spaced staggered center rows.
Base Ply. (0ptl0091) Polystick MTS Plus, seg-adhered.
Underlayment Mule -Hide SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet FR), Polygex SA P, Po"ex SA P FR, Potystkk TV Max, P°rysdck
TV P or Polystick TV Plus, seg-adhered.
Ril Maximum Design p -375 at;
Deck: Min .13/32-Inchplywoodtomeetprojmmquimmentst^uthfacti°nof AuthorNy HavinglurisdkNon.
Base Sheet: One (1) or two (2) layers ASTM D226, Type II fell
Fasteners: 11 ga. x 1.254r ch 1.9x 14nch head diameter round metal up nails
Spacing: cinch ri c. at the 3-Inch wide side laps and 12-loco O.a, at two (2) equally spaced staggered center rows.
Underlayment Eastoflex %G, applied In full mopping of hot asphah.
NEW ETC, U4
Rngmtt a/Ayrl,ms run oa2x55 7^'EDITION (20201 FIC NON-NVH2 EVALUATION Enlua[IPn Report P12p6a,p2.09-a2)
PotyglessgoofuiMeda Fi52S 33
ymenb Berl 27: 03130/2030
Prge 8 of 17
012 Maximum Dealen Lressure--4 at': 0NEMO f etc.
Deck. Mm. 19/32-inch plywood to meet nett requirements to satisfaction of
Base Sheet: one (1) layer ASTM D226, W) q Authority Having JUHstllction.
Tope II kid
Fasteners; 11 ga. x 1.25-Inch x 3/a-inch head diameter annular ring shank roofing nails at l-5/8-inch oiametertin.ps
Spacing: 4-inch ox at the 24nh wide side laps and flinch O,c,attwo(2) equally spaced Staggered renter rows.
Base Ply: (Optional; for use with self -adhering underlaymem only) POIysOck NITS Plus, selfadhered,
Underlayment: Mule -Hide SA-APP Up Shen, Mule -Hite SA-APP Cap Sheet (FR),
TU P Or Pulystick TU Plus, sefl-dhered. POty(lax SA p, palypex SA p Fit,Polyst(ck TU Max, Polystick
a
913 Maximum Design P
Deck: Min. 19/32-inch Plywood to meet ro ect
Base Sheet Two (2) IayerS WPly Plywood
D22to m e ll kit requiremants to satisfaction of AuthontV Having Judsdictlon.
Fasteners: 11 ga. x 1.25-inch long x 3/&Inch head diameter annular ring shank roofing nails at 1-5/8-inch diametertin caps
Racs Ply:ing: (Olp6o..r farat he 2Arhs wideSidelaps and 9-iwh0 c.atIWO(2) equally spaced staggered center rows.
Underlaadhering underlaymerd only) POFFack NITS plus, selfadhered.
yment: MIL -Hide SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet (FR), PolyRex SAp, polyFlex 5p p FR, PotysUck TU Max, Polystick
TU P or Polystick TU Plus, self -adhered or Elastdflca 56 G,a iced in fullm
#14 Maximum De' Pressure--45 sf: pp an I;
ofhot asphaB,
Deck: MJn.hearie Inchplywood to meet Project requirements to satisfaction o/ Authority Havinglunsdlctan.
Base meet: Elastobaze(sanded top surfxe fw hotaNxi ft or torch -applied cap or poly -film wrtace for torch -applied cap(
Fasteners: 5impiex MAXX Cap Fasteners
Spacing: 9-Inch OX. at the 2-Inch wide side laps and 18-Inch 0.1. at two (2) equally Spaced staggered center rows,
Undenayment: Elwmflex 36 G, applied In full mopping of hot asphalt or PolyRex G, torch-applietl.
#15 Maximum Des' Pr su a —. 5 n neE.
Deck: APA ratad,7Ji6 CAT, 0.418 in., Exposure 1, O58 Sheathin to
Jurisdiction. 6 mee[projett requirements to satisfaction of Av[hwiry Having
Base Sheen Elastobase or Mule -tilde Nall Base(paly-film tap surface)
Fasteners: 12 ga. annular ring shank nails with 1-5/8" diameter tin caps
Sawing: &Incho.c.wthe3-inchwid. Odelapsand6-1ithos at four(4) equally spaced aphip ed,enter
Base Ply: (Optional) Polystick MTS Plus, self -adhered. mws.
Undedayment Mule -Hide $A-APP Cap Sheet, MUle-tilde SA-APP Cap Sheet (Fa), Polyflex SA p, PWyflex SAP FR, Polys[irkN Max, PolystlCk
TU P or Polystick TU Plus, self -adhered.
#16 Maximum Des' Pre a--458 sf:
Dads: AP
DaArated,7/S6 CAT,0.41g in., Exposure 1, OSBsheahlssg to meet project requirements to satisfaction ofAuthorlty Having
Jurisdiction.
awe Sheet: Ekwmbse(Send top surrem)
Fasteners: 12 ga, annular ring shank nails with 1-5/8" diameter tin caps
p rig: 6-Inch o.c. at the 3-IMh wide Side laps and 6-inch n.c.atfour (4) equally spaced staggered center mws,
Undellayment ElastoNex S6 G, applied in full mopping of hat asphalt.
H17 Max
Deakin ,4 D
Da.
eck; APArated,7/16 CAT,0,418 in., Exposure 1, OSB sheathing to meet project mouirememio satisfaction ofAUtherlty Having
Jurisdiction.
Base Sheet Elastabase or POInhas Base
Fasteners: 12 ge, annular ring shank nails with 1-5/8" diameter tin caps
Spacing: 6-inch o.c. at the 3-Inch wide 'We laps and&inch o.c. at four(4) equally spaced staggered center rows.
Underlayment: POWINS, G, tominapplied.
H18 Marlmum Design Pam. _SZ,5 p f,
Deck: Min. 15/32-Inch Plywood to meet project requirements to satisfation of Authority Having Jurisdiction,
Base Sheet Elastobase(sanded top Surface for hot-asphaRor torch -applied cap or pdy-fiimwrtacefortordrapplied cap)
Fasteners: Simplex MAXX Cap Fasteners
Simi 9-Inch O.C. at the 2-inch wide side laps and 12Anch ex. at pass 12) equally spaced staggered center rows.
Underlaymenn Elastof ax S6 G, applied In full mopping of hot asphalt or Pelynex G, torch -applied.
ll.•'I.Ti7iRg
CSMJkaNgrAUMa6etAwMUSS 7' for"ON(20JAi FSC NON-HVHZ EVALUATION Evaluation Report P12p6p,WSIFR}}
FLS}69-Rai
POiEglass Roof UMmMs edeyeRevision }}:09/30/SON)
PSI
019 "Bad 4m Design P es - 52.5 two: NNEMOjetc,
Deck: Min. 35/3;-Inch PA'wootl to meet project requiremeotr to satisfaction Of Authority Havingluristlktlon.
gaze SheeC FastenersElas[obase or Mule -Hide Nail Base (poty-8lm top surface)
: Simplex Original Cap Nall,
Spacing: Simplex
o.a at the 3-irx:b wide side laps and 6-mch o.c. at four (4) equally spaced Base Ply: (Optional) Polysdck MTS plus, self -adhered. staggered center rows.
Underlayment Mule -Hide SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet (FR), Poiyfiex SAP, Was SA P FR, PolysUck TU Max, PolysNck
TU P or Pulysdck TU Plus, self adhered.
420 Maximum Des' n Pressure - 525par,
Deck: Min. 15132-inch Plywood to meet Preject
Base Sheet Elastobase(sanded top surface furhot-asphalt pplhants to $faction of Authority Having Juristlld:lon.
Fasteners: Simplex Original Cap Nall, applktl tap or poly-flim surface for up)
cap)
Spacing: 6-inch o.c. at the 3-inch wide side laps and 6-Inch o.c. at four (4) equally spaced staggered center rows.
Underlayment el urraff x 56 G, applied in full mopping of hot asphalt or Polyffex G, torch -applied.
#21 Max' um peskin pm,re -WW
Deck: Min.19/32-inch Plywood to meet Project requirements to satisfattion of puthodty Having Jurisdiction.
Base Sheet Elastobwe(sanded tap surface for hot -asphalt or torchapplled op or poly -film surface far torch
Fasteners: it Be. x 1.254nch long x 3/81 head diameter annular ring$bank roofing nalh cap)
Underlayment: Elastogex $6 G, applied in full mopping of hot asphalt or Po"ex G, at i-5f&intlr pi -applied der caps
Spacing: 8-Inch o.c. at the 44nch wide side laps and 8-Inch o.c. at three (3) equally spaced staggered canter rows.
#22 Maximumb I Pr, e--60 f: torthapplied.
Deck: Min. 19/32-lrxh Plywood to meet project requirement to satisfaction Base Sheet Elxstobase (sandedt surface for hot- of Authority Haring Jurlsdlcton.
Fasteners: OMG412 Standard Roofgnp with OMG Flat Bottom Metall pllatesup or P-1 im surface for torch-applled cap)
$Pacing: 12-Inch O.cat the 44r fi wide side laps and 12-incho.c. at two(2)equally spaced staggered center rows.
Undedaymera: Elastoflex S6 G, applied in full mo ppng of hot asphalt or Polyflex G, torchapplied.
423 Maximum Design Pre$ sf:
Deck: APAnted,2/16CAT,OAlBio.,Exposurel,0S9sheathingtomeetprojera requirememstosatif/a .nof AuthorityHaving
Jurisdiction.
Base Sheet: Elestobace or Mule -Hide Nall Base (polifilm top surface)
Fasteners: Simplex MAXX Cap Fasteners
Sparing: Xmxho.cat the 3-Inch wide side laps and &incho.c. at three (3)equallyspaced staggered center rows.
Primer. PG3W or ASTM WI primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, Pelf -adhered.
Usderlayment: Mule -Hide SA-APP Cap Sheet,Mule-Hide 3A-APP Cap Sheet (FR), Po""SA p, polyn"SA p FR, polystiok TU Max, POJystkk
TU P or Folysdck TU Plus, s.frccMered.
#24 Maxi DeSign
i P W-0-W:
Deck: APA ratetl,])16 CAT,nA38in.,Exposurel,0$8,heathln tomeet
hol.dictbn g project regWrementsto satisfaction of Authority Having
Base Sheet: Elasmbase(sand top surface)
Fasteners: Simplex MAX+( Cap Fasteners
Spacing: &inch oc. Athe 3-inch wide side laps and&inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastofiex S6 G, applied In full mopping of hot asphalt.
#25 !-Um D sAigg P ,7-0,
DeckAPAnte/16CfATD41g:
in.,Exposuml,0Seshethin tomat ro1ectJurisdiction. re quirememtoatisfaconofAuthoriry HM
ease Sheet: Elastabase or Polygless Base
Fasteners: Simplex MAXX Cap Fasteners
Spacing: flinch o.c. A the }Inch wide side laps and 84bsch c.c. at three (3) equally spaced staggered center rows. Underlayment PolyBex G, conch -applied.
NEMo ErC, ltC
tPRiift-v fpuf olaoiii g310, 7f EOITION(20201 FRC NOv RVNZ fVA1.UATION Eyaliatl0a Report P12060.02.99-1127
Polyglxs Reef UmkHaymem, Pt3259.431
Rvvbkan 22: Mlypison
Page 10 of 17
426
#2
#28
#29
#30
#31
#32
Maximum Deslan Prss e--675oSt. NEMO�EtC.
Oeck, MIn. 15/32-Inch plywood to meet Project
Base Sheet: Poiyglass G28as PlYw p ) requirements to satsfaclon of Authority Having jurisdiction,
Fasteners: 12 oWgla5s Baaa "MulOw use of torch-OPPged ondoH lme T)
ga. x 1.ZSInch Ipngx 318-inch head diameter annular n lg shank roorrg nails at 1.5(&Inch diameter tin caps
Spacing: 8-Inch o,c. at the 4-Inch wide side laps and &inch o.c. at four (4) equally spaced sWggeretl center rows.
Undedayment Elastoflex S6 G, applied in fbll mo
7 MBXI D ,gn PPingofho[acphaltortorchrepplled-PO"ex Gtorch-appled.
es Namur, 5 0.,k
Deck APA rated, 19/32 CAT, D578 In., Pxpowre 1, OSB sheathing to meet project requirements To satisfaction
of Authority
Having Jurisdiction.
Base Sheet EWstabase or Wartime Nail ease (Poly-flim top surface)
Fasteners: TRUFAST Vera -Fast Fasteners & Plates with two (2) screws per plate Installed 10' into the holes of Me plate, parallel to
the width direabn of the sheet.
Spacing: 12-inch Oe atthe'inch wide side la and 12-
Primer: r indrew Platwo(2)equally spaced staggered center rows.
(Optional) PGIDO or ASTM D41 primer applied to stress plates.
Base Ply: (Optional) PoWstkk MTS Plus, self-atlhered.
Undenayment: Mule -Hide SA-APP Cap Sheet, Mule-HMe SA-App Cap Sheet (FR), polyflex SA P, Po"m SA P Fg pplystit* n Max, poWstkk
TU P ar Polystick TO Plus, self -adhered.
Mai mm uDeal n PrM
Deck: APA ratCAT, D 57g in., Ex
Having jurisdiction, pasure 1, 05B sheathing to meet project requirements to satisfaction of Authority
Base Shea[ Ebstobase(sand pop surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two [2) screws per Plate installed 180' into the holes of the plate, parallel to
the width direction of the sheet.
Spacing: 12-Inch O.C. at the 4-1nch witle side laps and 12Anch oe. at two (2) equally spaced staggered center news.
Underlaymem Elastoflex S6 G, applied in full mopping of hot asphalt,
Maximum DeI Fire
y--675tuf
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, 056 sheathin to meet project Having Jurisdktlon. g requirements m satisfaction of Authority
Bare Sheet: Hastobass or Polygiass Base
Fasteners: TRUFAST Vera -Fast Fasteners & Plates with two (2) screws per plate"stalled IN' into the hales of the plate, parallel to
the wdth direction of the sheet.
Spacing: 12-inch o.c. at the 4-Inch witle sde la
Underlaymem: Po Ps and 12dnch o.c. at two (2) equally spaced staggered center rows.
lyflex 6, torch-applietl.
Maximum Design p 75
Deck: MIn. 15/324nrh plywood to meet PIJM Base Sheet: Polyglass G2 Base or Polyglass ease (requires we o torch Opittts tO staceon of Authwlty Having jurisdiction.
Fasteners: Dekfast#14 with Deafest Hex places 'ONTO #14 HD with OMG 3'Galvalume Steel Plates, OMG Rolohmp#14 with OMG Flat
Bottum Plates (AcwT.0, West HD with Tmfast }inch Insulation Plates or Simplex MAXX Cap Fasteners
Spacing: 10-inch o.c, at the 4-inch wide side laps and ID -Inch o.c. at three (3) equally spaced staggered eerder rows.
Underlayment: Elastoflen 56 G, applied in full mapping of hot asphalt or torch -applied or Po ax G, torcr
PP 8 W'fl applied.
Maximum Design� f.
Deck: MIn.15/32-InCh plywood to meet pmject requirements to satisfaction of Authority Having Jurisdiction,
Base Sheet: Elastobwe(sanded top surface for hat -asphalt or torch -applied cap or poly -Alm surface for torch -applied cap)
Fasteners: Simplex MAXf( Cap Fastener
Spacing: 6-Inch O.C. at the 2-bch wide side laps and 6-inch ex. at two (2) equally spaced staggered center rows.
Urderlayment: Elastoflex 56 G, applied in full mopping of hot asphalt or Polyflex G, mrch-applied.
Maximum Denatur Pressure =-90 psf;
Deck: Sam-15(32-inch plywood m meet project requirements to satisfaction of Authority Having Jurisdiction.
Rase Sheet: Eiastobase(sanded top surface for hot -asphalt or toech-applied cap orpoly-flIm surface for torch -applied cap)
Fasteners: OMG 912 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3" Round Metal Plates or OMG Flat Bottom Metal Plates
Spacing: 6-inch Ge. at the 4-inch wide side laps and 6-inch o.c. at thres(3) equally spaced staggered cantermyVa. Underlaymem, Elastoflex S6 G, applied In full mopping of hot asphalt or Polyfle%G, torch -applied.
NEMO VC, LEt
hnNxreafnuNw,aorana7a9ss 7°1 ED17101a DEDO)FRC NON-HVHZ EVALUATION Evaluation Report P12060.OL09,R27
Polatex RoofundenaymenU N5259•MS
Revlsbn 77: 011/30/2010
Pane 11 of 17
#33 Maximum Design Prey sf. NNEMOjetc.
Deck: MID.15/32-Inch plywoppd to mme project requirements to satisfaction of Authority Having Jurisdiction.
Rase Sheet Elascobase(Banded top surface)
Fasteners: TmfaM#120Por Tmfast#14HDwith Trufart3'Metalinsulatinn Plat es
Spacing: 64nch D.C. rtthe flinch wide side laps and 6-inch D.C. at three (3) equally spaced staggered center rows.
Undenayment Elastoflex S6 G, applied In full mopping of hot asphalt.
#34 MaxIMUM Design o.
Deck: �`—pilf: MID. 15/32-Inch"Yapped to meet project requirements to satisfaction of Authority Having Ju
Base Sheet: Polyglass G2 Base or Polyalass Base (requires use o torch- tY 8 r&dittlon.
Fastener: DeMast#14 with De least Hex Planes, OMG914 HD with OMl3'G.lvalumeSteel Plates, OMG RoofgdP#14 with CMG Flat
Spacing:
Bottom Plates *C-Traa), Truf St HD with Tmfoa 3-inch Insulation Plates ors mplex mN Cap Futeners
9-mch o.c. at me4-Inch wide side laps and 9-Inch o.c. at four (4) equallyspaoed staggered center rows.
Undedayment ElastoBex S6 G, applied in full mapping of hot asphak or torch.applied or Polyflex #35 MDMUMDe , ,D4a
ro G, torch-appletl.51 aduCAT0, ngmerectArarej16
Jurisdiction.WrequimmestosadsfaaionofAuthodty NaAng
Base Sheet: EWstohaase Of Mule -Hide Nail Base(Poiy-film top surface)
Fastener: TRUFAST Versa -Fast Fasteners & Plates Mth two (2) screws per plate installed 180- into the helps of the plate, parallel to
the width -direction of the sheet
Spacing: 9dnch o.c. M the 2-Inch wide side laps and 12-inch o.a at two (2) equal) primer: PG100or ASTMD4lprimerapplkdtostressplates. Yspaced staggered center rows.
Base ply; (Optional) Polystick MTS Plus, sell -adhered.
laym:
UndermoMule-Hide SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet (FRf, Po
ty11ex SA P, Palyflex SA P FR, polys[ick TU Max, PolysHck
TU Por Polystck TU Plus, self -adhered.
#36 Maxi Um Des' P�DoL
Deck: APArated,7/S6CAT,0.418 in., Exposure 1, OSB sheathingto mee[Project requiremaMSWsrtttfactbn of Authority Having
Jur6tli<[ion.
ease Sheet. Elastobaze (send top surface)
Fasteners: TRUFAST Versa -Fast Fasteners &Plates with me (2) screws per plate Installed 180- in, the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 9-inch D.C. at the 2nch We side laps and 12-Inch o.c. at two (2) equally spaced staggered center rows.
Undedayment Elastoflex S6 G. applied In full mopping of hot asphalt.
#37 Ma%ilpum D i n e 5um =
-900 g'
Deck: APA Jurisdiction.
rated]/16 CAT, 0.4181n„os Expure 1, OSB sheathing to meet protect requirements to satisfaction of Authority Having
gale Shea: Ebrtobsea or polyelass Base
Fasteners: TRUFAST Versa -Fart Fasteners & Plata with two (2) screws per plate installed 180- into the holes of the date, parallel to
the width-directon of the sheet
Spacing: 9-inch o.c. at the 2-inch wide side laps and 12-Inch D.C. at two (2) equally spaced staggered center rows.
Undedayment POIyRex G, torch -applied.
U38 hiQ mu 0�_ -97 5 Mf:
Deck: Min.19/32-inch plywood W meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Basp(poly-Rim top surface)
Fasteners: 11 ga. x 1,25-inch x 3/8-Inch head diameter annular dng shank roofing nails at 1-5/8-Inch diameter Rn caps
Spacing: 4-Inch D.C. at the 4-Inch wide side laps and 44nch O.C. at four (4) equally spaced staggered center rows.
Base Ply; (Optional) PolysHck MTS Plus, self -adhered,
Undedayment Mule -Hide SA-APP Cap Sheeq Mule -Hide SA-APP Cap Sheet (FR), POlyflex SA P, Polyllex SA P FR, Pohystick TU Max, PolysHck
TU P or Polystkk TU Plus, self -adhered.
NeMo£TC,LLC
CnrGimfa°/AuMpk°fl°^#aT<St T'" EOmON(20i0) FK NOW"" EVALUATION EVdU`dOn RepoN P12060.02.094127
PalyglassRoofumdedaym oss FU259-Ml
Revhloe 27: o9/30/2020
Page 12 of 17
939 MaximuMD a ONEMOletc.
APA rate, 19132 0.578 in., Exposure 1, o5B sheathing to
Having Jurisdiction, meet protect requirements to satisfaction of Authority
Base Sheet: Eimenbew or Mule -Hide Nail gale (poly -film top surface)
Fastened! Simplex MAXX Cap Fasteners
Spacing: 6-Inch O.c. at 41nch wide side laps and lunch o,c. at Four (4) equally spaced staggered center rows.
Primer: P13100 or ASTM D42 primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, self -adhered,
Underlayment: Mule-HIde SA-APP Cap Sheet, Mule -Hide SA-APP Cap Sheet (FR), polytle, SA P, polynex 5A p Fry Polystkk TV Max, Polystick
TV P or Polystick TU Plus, self -adhered.
#40 Me, mum Design Pressure 975 usf
Deck: APA rated, ictir CAT, 0.578 In,
HaWnglunsdkibn. Exposure 1, OSB sheathing to meet protect requirements to satisfaction of Authority
Base Sheet Elastobase lsand top surface)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 6-inch o.q at the &inch wide side laps and 6-inch o.c. at four(&) equally spaced staggered center rows.
Underfayment: Mendell" 56 G. applied in full mopping or hot asphalt.
#41 Max-m nnD i Pressure
s - 975 sf:
Dedr: APA rated, 19/32 CAT, 0.f ]8 in., E%Poeere 1, OSB sheathing To meet project requlremenis to satisfaction of Authority
Havinglurisdicuon.
Base Sheet: Elastobase or Polyglass Saw
Fasteners: SImPIex MAXX Cap Fasteners
Spacing: &Inch o.c. at the flinch wide side laps and&inch oe. at four (all equally spaced staggered center rows.
Undere meet: Polynex G, torch -applied.
442 Maximum Design Pressure - 105 led:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Judsdiction,
Base Sheet: Elastobaee(sanded top surface for hot -asphalt or torch -applied cap or p*.Rlmsurfacefortorrh-
Fasteners: Simplex MNIX Cap Fasteners applied cap)
Spacing: 6-inch oe. at the 2-Inch wide side laps and 6-inch o.c. at three (3) equally sPa@ed staggered center tows.
Underlaymem: Elastoflex 56 G, applied in full mopping of hot asphalt or Panther G, torch -applied.
1143 Maxtmu De
p w - 105D f;
Deck: APArated,]/16 AT, 0.41g in., Exposure 1, OS6 sheathin to
Jurisdiction. B meet Protect requirements to satisfaction of Authority Having
Base Sheet Elaatobase or Mule -Nude Nall Base (poly -film top o dwe)
Fasteners: TRUFAST Veda -Fast Fasteners & Plates with two (2) screws per plate Installed 1 - into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: &Inch oc. at the &Iris wide side laps and 6-Inch c.c, at three (3) equally spared Staggered center rows.
Primer: PG100 or ASTM 041 primer applied to stress Plates.
Base Ply. (Optlonall Polystl& MTS Plus, self -adhered.
UnderWYment Mule -Hide SA-APP tap Sheet, Mule -Hide SA-APP Cap Sheet (FR), Po
pdynex SA P, Poiyflex 5A p FR, Polgstick TV Man, tystick
TV P or Polysbek TV Plus, se#adhered.
#44 Maxim nd Des' n P ure 105 0 f;
Deck: APArated,7/I6 CAT, 041811., Exposure 1, OSBsheathingto meet project requirements to satisfaction ofquthority Navin,
Jurisdiction.
Baue Sheet: Elastdease(sand top surface)
Fasteners: TRUFAST Versa -Fart Fasteners & Plates with two (2) screws Per plate installed 280° Into the holes of the plate, parallel to
the width-dwel lon of the sheet
Spacing: 6-Inch o.C. at the b rich wide side laps and 6-Inch o.c. at three (3) equally spaced staggered center rows. Underlaymentr Elastoflex 56 G, applied in full mopping of hot asphalt.
NEMO ETC, 'LC'
CwtfgmreojAUMadMMY32A5a >TM EOniON (2a2gJ Fa[NON-NVH2 EVALUATION Evaluation Repent PIZO(iDB2.e9-R2)
Pdy4lass Roo Urawdayments H5259-R31
Revised Z7: B9y3ej1020
Rational?
#45 Mxxiirrl_yrn De'gam=05a . ONEMo etc.
Deck. APArateq]/16CA7,O.A1g in., Elxposure l,OSB sheathing to meet project requirements to satisfaction of Authority Having
gave Sheet Elasmbau Or polyglass Base
Fasteners: TRUFASt Versa -Fast Fasteners III Plates with Two, (2)screws per plate installed l&1• into the holes of the plate, Parallel [o
the width -direction of the sheet
Spacing: 6-inch o.c, at the &inch wide side laps and 6-Inch O.C. at three (3) staggered center rows.
Underlayment P.Mkos G, touppli ch-aed. equally spazetl rt
#46 MinimumD e�n PrZw a 112 5 onf-
Deck: Min.19/324nch plywood to meet Project requirements to satisfaction of Authority Having lurisdktlon.
Base Sheet: Elastobase w Mule -Hite Nall gase(POIY-film top surface)
Fasteners: 11 P. x 1.25-inch x 3/8-Inch head diameter annular ring shank roofl^g nails at 1-5/8-inch diameter Hn cups
Spacing: &inch O.c. at the&inch wide side laps and 6-Inch o,c. at four (4) equally sp�cedstaggered <emer mws.
Primer: PGIDO or ASTM D41 primer at all Hn-caps
Base Ply: Polystkk MTS Plus, self -adhered
Under"Yment Mule -Hide SA-APP Cap Sheet, MOIe-Hide SA-APP Cap Shea (FR), M
Polyllex SAP, POW"x SA P Fp, PolysHrk TU Max, Polystkk
TU P Or Polystick TU Plus, se# -adhered.
#47 Maximum Delon Pressure_ 12C aef.
Deck: Min. 15/32.inch Plywood to meetProject:
Base Sheet: Elm1base(sanded top surface fo hot requirements to utIOX11On of Authority Having Jurisdiction.
Fasteners: OMG #125tandard pool & t asphalt or torch -applied uporpoty-Fllm surface for torch-applletl up)
spacing: p or OMG kid Heavy Duty with OMG 3" pound Metal Plates or OMG Flat gottom Metal Plates
B 6-Inch o.c. at the 4-Inch wide side laps and 6.0mh o.c. at five(S) equally spaced staggered center rows.
Und-)IOnent; Elastofiex S6 G, applied in full mopping of hot asphalt or Po"ex G, torch -applied.
#48 Maximum De ' n Pressure - sf.
Deck- Min.15/32-Inch plywood to meet project re ulre
Base Sheet: ElastOlame(sanded tap surime) q merits to satisfaction oFAuthorhy Having Jurisdiction.
Fasteners: Trufast912 UP of Trufast#14 HD with Trufmt 3" Maui insulation plates
Spacing: 6anch O.C. at the &inch We Ad. lap and &rosin It. at five (5) equally spared st
Under(Ryment E7astoflex M G. applied in full mopping of hot asphaltaggered center rows..
i149 Maximum Dpl Pres u e- 3 76EISC
Deck: APA rated, 19/32 CAT, 0,578 in., Exposure 1, OSB sheathing to meet prolett requirements to satisfaction of Authority
HavingludOldion.
Base Sheet: Elastobase or Mule -Hide Nall eau(poly-film top surfare)
Sparing:
Fasteners: TRUFAST Versa -Fast fasteners&Plates with One screw per plate, in the center hole. 9-Inch o.c. at the &Inch wide side laps and 9-Inch 0.1, at four (4) equally spaced staggered center rows.
Primen,PG1O0 or ASTM D43 primer applied to stress plates.
Base Ply: (Optional) POWICk MTS Plus ,self -adhered.
Undorerment Mule -Hide SA-APP Cap Shell, Mule -Hide SA-APP Cap Sheet (FRI, Polyflax SA P, PplyflsX 5A P FRI, Pohystick TU Max, Pdystitk
TU P or Potystkk TU Plus, self -adhered.
#50 Ma%IMUM Cast P - 1275 is
Deck APA rated, 19/32 CAT, 0.578 in., Exposure L OSB sheathingto ro'
HavingluHsdictem. meet P Jtxt requirements Onsatufacion of Authority
Base Sheet: Elastobam(sand trip surface)
Fasteners; TRUFAST Verssfmt Footmen & Plates with me 11) screw per Elplate, in the center hole.
Sparring: 9-mch O.c. az the ¢inch wide side laps all 9-inch O-c, at four (4) equally spaced staggered center rows.
Undedaymenr. astoFlex%G, applied In full mopping of hot asphalt.
#51 M`AiM__ De per9 1275 mi:
Deck: APA rated, 19(32 CAT, 0.578 in., Exposure 1, 058 sheaths to
Having Jurisdiction. rig meet project requirements to satishcNon of Authority
Base Sheet: Elastobase or Polygiaas Bass,
Fasteners: TRUFAST Versa -Fast Fasteners"Plates whh on. screw per plate, in the ceme, hde.
Spacing: 9-Inch O.C. st the 4-Inch wide side laps and 9-Inch o.c. at four (4) equally spaced staggered center rows,
Undedayment: Polytlex G,torch-applied.
NEMO ETC, UC
T<dkAaK erNRlmaa(i°naaM55 7'EDITION (2020)Fail NON-HuhZ EVALUATION Evaluation Repprt P12060.02.09-1127
Pdvglses Roof umeri'meds FUZS9-R31
hands. 27: 09/se/2020
Paat14d17
5.9 Exposure LImitators- NNEM10jetc.
7ABIE3: EAPrsUr6L[lomtIW1q
undelaymant Prepgred Roof Cover
Elestehate, Eh 'retaliation Maximwn
stobase P, PolyBiess G2 Rase or Pdygiass Base �° Exposure (days)
Polystick lR-Xe or Polystick MU-X Mechanicallyattached 30
HydraGuard Dual Pro, HydraGuard Tile Pro, Pa Mechanically attached 30
TU P, Potystick TU Plus or PolystiA XFR Nstck NITS Pluc, Pohystck TU Max, PoF/stick
Atrytype (per Table i) 180
EIaaWRaz 66QElartoT"-=FR, Md1=SA-APPCap Sheet Mul"Hides APPcap Adhesive -set the roof system
Sheet (FR), PolyRez G, Polytlex 'I
FIR, Polyllex SA p or PolyRex SA P FR 1W
Mecheniwllyattachetl UNUMREO
5.10 Tile Slipa a Innitatj : When loading roof tiles on the underlayment in direct -deck the roof assemblies, the maximum roof
slope shall be as follows. These slope limitations can only be exceeded by using battens during loading of the roof tiles.
7AeM4: THESUPPAGNLUerATMMOPGADMea4)EaTILEINSTAttATlGf6
unaedRyme n THO Profile s..
Method
Elastoilex% G or SG G FA
rlB
Maximum S�Birrg 3bpB
Flat or Lugged
HydraGuartl Tile Pro
6-tilestack (4over2))
Prohibit dwithout battensFlat
or tugged
PolyRNt G or G Fit
&tie stack(4 over 2)
7:12
Hat of Lugged
Poly(lex5APw5A PFfl
6-Ule steck(4 over 2)
4:12
Flat or Lugged
6-tie stack (4 over 2)
Polystidt MT5 Plus Flat
6-Ole Stack(4 aver 2)
4:12
Lugged
6-tile atea(4 over 2)
5:12
Flat
5-tie stad(4 over 2) or, 10-tg, stack
a12
Palystkk TU M.Luggetl
71
Etge sta k(4 overt)
]:2�
Polystck TUP lugged
10-tlle stack
6:12
Flat or Lugged
6-tile stack(4 over 2)
PalysdUtTU plus flat or tugged
6-tile stack(4 over 2)
712
Flat or Lugged
10-tAe stack
7.12
PdystkXFR Flat or L egged
Prohibited without battens
fi:32k
ProhlWge vrRhOue oaasns
NEW ETC. LLG
RrOkNrOT o00^ � 7� EDITION (2020) FIRC NON HVHZ EVALUATION E.W.W. Report P330W.o2.0¢p2T
Palma. Roof UnderUrmwrts 11525¢Ral
REWrion 27:0"012020
PaPe15d17
6.3
rkF
Re-rasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove any dust
and debris prior to application, and prime the substrate (if applicable).
ElastoWse, Elastof7aso P ar Muk-N)de No Base:
Shall be installed in compliance with requirements for an approved mechanically attached underlayment (ASTM D226, Type
II) in FBC Table 1507.L1.1 or FBC Residential Table R905.1.1.1 for the type Of Prepared roof covering to be installed, and the
manufacturers installation instructions. FBC requirementstake precedence overthe manufacturer's installation Instructions.
Elastobase, Elastobase P or Mule -Hide Nall Base may be covered with a layer of Polystick IR-Xe, Polystick MTS Pius, Polystick
MLIA POlystick TU Max, Polystick TU P, Poyedick TU Plus, Polystick XFR, PolyRax SAP, POlyflex SA P FR, Mule -Hide SA-APp Cap
Sheet or SA-APP Cap Sheet (FR), self -adhered, Elastoflex 56 G or Elasfoflex S6 G FR in hot asphalt or POlyflex G or Po". G
Fit, torch applied, Roof cover limitations are those are those associated with the top -layer undedayment, as set forth in Table
1.
6.3.2 Tile Aoolicatia
6.3.2.1 Elastobase (poly -Rim top), Elastobase P (poly -film top) and Mule -Hide Nail Base are limited to use as a mechanically attached
base sheet in the' TWo-PLY SYSTEM" from FRSA/TRI FloNda High Wind Concrete and Clay Roof Tile Installation AfmUat, Sixth
Edition, followed by Polysdck NITS Plus, POlystick TU Max, Polystick TU P, Polystick TV Plus, PolystickXFR, Potyflex SAP, Polynex
is,
SAP AR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR). self -adhered or PolyflexGOr POIVHexGFR,torch-applied, Tile
roof installation method Is limited by the selected Cap Sheet, as set forth in Table 1. Refer to Section herein for
attachment requirements.
6.3.2.2 Elastobase (sanded -top) and Elastobase P(sanded-top)e are limited to use as a mechanicallyattached base sheet in the "rw0-
PLY SYSTEM" from PRSA/TRI Florida High Wind Concrete and Clay Roof Tile installation Manual, Sixth Edition, followed by
Elastoflex S6 G, Elastoflex S6 G FR or an FRC Approved Mineral Surfaced Cap Sheet (ASTM D6380), ,phaltapplied or Pofyfla%
G or Poiyflex G FR, torch -applied. Tile roof installation method is limited by the selected Cap Sheet, as set forth in Table 1.
• When Elastobase (sanded -top) or Elastobase P (sanded -top) is followed by asphalt -applied Elastoflex 56 G, Elastoflex S6
G FR or FBC Approved Mineral Surfaced Cap Sheet (ASTM D6380), refer to FRSA(TRf, Sixth Edition, Appendix A, Table T
or Section S.8.3.2 herein for attachment requirements.
• When Elastobase(sanded-top) or Elastobase P(sanded-top) is followed by torch -applied Poiyflex G or POIYfiex G FIR, refer
to Section 5.83.2 herein for attachment requirements.
6.4 HydraGuard Dual P% HPANIGuard Tile Pro,Mule-HIde SA."p Cep Sheet,Mule-HIde SA-APP CaP Sheet (PRb PoI
P�X ISA P Fit Piny & BFXe, PoWfck MT5 Plus, Polystkk AlPol tick TU P Tflex SA P,
Polystick XFR: Ys a%, olyatltk 7U 0, Poryatick TU Plus or
All seal -lap seams (selvage laps) must be firmly roiled with a
In accordance with Polyglass requirements to ensure full
contact and adhesion. For Hyd,Guard Dual Pro and
HydraGuartl Tile P% align the edge of the top sheet to the
end of the glue pattern (the sheet will overlap the fabric).
We' of OvN-P seam of Hydmeuard Dual PN aid HyJraawrd nle Pro
MEMO CTc, Luc
UmPANeeAwoNAAAAan1'` 7"EDITION i20701 FBC NON-HVH2'VALUATION Evaluation RePOn Pl306de1a9-R27
Polyglass Roof Underlayments F15259 R31
Revisbn 27: NIM/M20
P.E. 16 At 17
6.4.2 Non -Tile Applications, ONEMOletc.
Shall be Installed In compliance with requirements for an approved self -adhering underlayment (ASTM D3970) in FBC
1507.1.1.1 or 1507.1.1.3 or FBC Residential R905.1.1.1 or R905.1.1.3 for the type of prepared roof covering to be installed,
and the manufacturers installation instructions.
When installed over a mechanically attached base sheet of FBCApproved ASTM 0226, Type II felt, Elastobase, Elastobase P or
Mule -Hide Nail Base, the base sheet shall be fastened in accordance with FBC 1507.1.1 or R905.1.1.
6.4.3 Tile Aopl�at- gcludes Hvd G,,...r n.
Shall be installed In compliance with the requirements for Self -Adhered Membrane l set forth in F
Concrete and Clay Roof file installation Manual, Sixth Edition and the manufacturer's installation insstru<Ho sudda High Wind.
Refer to Section 5.8.3 herein for attachment limitations.
Refer W Table 4 herein for tile staging limitations.
6.4.4 Multi -Ply Unde la m nt Systems.
Polystick MIS Plus or Polystick XFR followed by HydraGuard Tile Pro, Polyflex SA p, Polystick NITS Plus, Polystick MU-X, Polystick
TU Max, Polystick TU P, Polystick TU Plus of Polystick XFR is allowable for use under attached prepared roof
systems. Limits of use are those associated with the top -layer material. Thimechanically
is not a requirement, but is allowable if a 2-ply
underlayment system is desired.
Polystick MTS Plus followed by HydraGuard Tile Pro, POlyflex SA P, Polystick TU Max, Polystick TU P or PONStick TU Plus is
allowable for use under adhesive -set tile systems. Limits Of use are those associated with the top -layer material. This is not
requirement, but is allowable if a 2-ply underlayment system is desired.
IS Elastal S6S or FlaFtaflm[566 FR•
651 Shall be install d pi th q m t an alternate to the Hot Asphalt Applied Cap Sheet" in the Two Ply
System' in the FRSAfTRI Florida High Wind Concrete and Clay Roof Tile lnsteliation Manual, Sixth Edition, and the
manufacturer's installation instructions.
Referto Section SS.2 and S.8.3 herein for attachment limitations.
Refer to Table 4 herein for tile staging limitations.
6.6.1 Shall be installed in compliance with requirements as an alternate to the"Heat Applied Cap Sheet" in the "Two Ply System -in
the FRSA/TRI Florida High Wind Concrete old Clay Roof Tile installation Manuel, Sloth Edition, and the manufacturers
installation Instructions.
RefertO Section 5.33 herein far attachment limitations.
Refer to Table 4 herein for the staging limitations.
As
wruacs One named Oq entity for manufacturing facilities covemd by F.A.C. Rule 6162t
4 herein for products and production locations having met codified material standards.
-END OF EVALUATION REPORT -
NEMO ETr, LLC.
Cemfxrohggyrrypp,oryon paNSy 7' E09ION 12020i FOC NON-WW EVALUATNNI ewartrun"PerL PU061102.094Q7
PolysgLr Re9f UMadeymanb Fun"31
Rw1%ioa27:09/3a/2o2a
Pa 17 of 11