HomeMy WebLinkAboutPool heater informations P ,"�
";"s(.jr e<x''.
Choose between one of our top -performing models.
OPERATING SPECIFICATIONS
TH105
TH125
TH140A
Voles
230
230
230
Hertz
60
60
60
Phase _ -
Compressor amps
1
23.2A
1
24,3A
1
27.3A
Cooling
V es
Yes
N0 --
Heat exchanger
Titanium / PVC
Titanium / PVC
Titanium / PVC
Fan motor max. load amps
2.4A
2.4A
2AA
Fan motor HP
1/3
1/3
1/3
Fan motor speed
825 RPM
825 RPM
825 RPM
Minimum circuit ompacity
40 A
42.5 A
42.5 A
Maximum fuse
_
60 A
_
60 A
60 A
Compressor
Copeland scroll
Copeland scroll
Copeland scroll
TEST PERFORMANCES
80F amb, 80F water, 80% RH 105,000 BTU/h 121,000 BTU/h 137,000 BTU/h
COP 6 5.5 6
80F amb, 80F water, 63% RH
100,000 BTU/h
116,000 BTU/h
131,000 BTU/h
COP
5.8
5.3
5.8
50F amb, 80F water, 63% RH
70,000 BTU/h
80,000 BTU/h
87,,000 BTU/h
COP
4
4
4
Defrost
Hot gas
at gas
Hot gas
Refrigerant
R-Al0A
R-410A
R-410A
Optimal water flow rate (GPM)
40
55
60
Max. water flow rate (GPM)
100
100
100
Max. water temperature
104F
104F
104F
Net Weight (Ibs)
230
245
265
Shipping Weight (Ibs)
275
290
310
Dimensions (in.)
H: 34 L.33 P:39
H: 34 L:33 P:39
H: 34 L-33 P:39
Shicoina dimensions (in.)
H: 39 L:35 P:44
H: 39 L:35 P:44
H: 39 L•35 P:44
tvodOls for hi-g-Guild pools
Dimensions
Surface Liters
Gallons GOOD BETTER BEST
(ft.)
(R.2)
u5
12x24
288 45,460
11,900 TH105 TH105 TH105
14 X 28
392 61,323
16,200 TH105 TH105 TH105
15 X 30 450 70,092 18,500 TH10S TH105 TH105
16 X 32 512 79,871 21,100 TH105 TH105 TH125
18 X 36 648 102,285 26,700 TH125 TH125 TH140A
20 X 40 800 124,918 33,000 TH140A TH140A TH140A
Al ; o.:;dcbie to TH55, -THE,_-Ti-1?5 Contact.:_ r^,r man; in'crmc'I;r
�,THER_ M
POOL HEAT PUMPS
T
6' minimum
81
12"
ji
Front
Front
12"-� 6" Minimum 6' Minimum
Top view
THERM,
POOL HEAT PUMP
48" Minimum
12'Minimum
In compliance with the Florida Building Code 301.13, pool heat pumps
must be anchored to a structure for hurricane resistance.
Anchor are required on each installation.
Installation
1. Place the THERMEAU®Heat Pump
at its permanent location
on the equipment pad.
Installer to provide anchors bolts
and the suitable concrete anchor
to attach the angle steel bracket
to the equipment pod.
2. Place the angle steel bracket at the
bottom of the THERMEAVIteat Pump
as indicated (Fig. 11
3. Bolt on the angle steel bracket
to the base as indicated (Fig. 2).
4. Mark the position of the hole
in each angle steel bracket
on the backing material.
5. Drill a hole at each mark
into the equipment pad.
6. Insert a bolt anchor in each hole
completely.
7. Line up anchor the angle steel bracket
holes and bolt anchors (Fig. 2).
8. Put an anchor bolt in each angle
steel bracket.
Figure 1. Anchor Positions
Attach anchor brackets to base of heat pump
where indicated by the arrows.
Figure 2. Angle Steel Bracket
wa vuHR�
HEAT PUMP
PLASTIC
BASE
OWNER'S MANUAL THERM
POOL MEAT PUMP
325RRA 825RPM 825RPM Installation
l etalled® n Instructions
R-410A R-410A R-410A
40 55 60 Location
100 100 100
The placement of the pool heater is very important in keeping installation
costs to a minimum while providing for maxirnum efficiency of operation, as
104E 104F 104F well as allowing adequate access for set -vice and maintenance.
H:34 L33 H:34 L:33 H:34 L:33 The THERMEAU pool heat pump is designed for outdoor installation and
D:39 D:39 D;39
should not be installed in a fully enclosed area, such as a shed, garage, etc.
Recirculation of cold discharged air back into the evaporator coil will greatly
reduce unit heating capacity and efficiency.
The unit should be located as close as practical to the existing pool pump and
filter to minimize water piping.
Mount the unit on a sturdy base, preferably a concrete slab or a set of blocks.
The size of -'the base should not be less than 36" x 36" (91 cm x 91 cm).
1
OWNER'S MANUAL THERM 7
P00L HP T PUMP