HomeMy WebLinkAboutAPPROVED, 2464 Iroquois Ave Information Sheet*311 LUCIE
Section A (General Information)
Master Permit No. Process No.
Contractors Name: U I�C 1 W �L � License # `I C33 [q`''
Job Address �,q
ROOF CATEGORY
❑ Low Slope ❑ Mechanically Fastened Tile ❑ Mortar/Adhesive Set Tiles
❑ Asphaltic Shingles 8`Metal Panel/Shingles ❑Wood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE.
❑ New roof ❑ Repair ❑ Maintenance Reroofing ❑ Recovering
ROOF SYSTEM INFORMATION
Low Slope Roof Area (SF) Steep Sloped Roof Area (SF) _ _ Total (SF)
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
■■■■■■■■■■■■■
■■
■■
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component is not used, i entify as
"NA")
System Manufacturer: I
Product Approval No.: 1 / 1 / Vi
Design Wind Pressures, From RAS 128 Or Calculations:,
7 q��•
Zone 1':—Zone 1: Ci ne 2: �Z ne 3:
Max. Design Preure, frgm the pecific product approval
system: yj
Deck:
Type:
Gauge Thickness:
Slope:
Anchor/Base Sheet & No. df Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s):
Base Sheet Fastener/Bonding Material:
Ply Sheet(s)' & No. of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply:
Top Ply Fastener/Bonding Material:
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':_.._."
oc @ Lap, # Rows
@
" oc
Zone 1:_"
oc @ Lap, # Rows
@
" ac
Zone 2:—"
oc @ Lap, # Rows
@
"ac
Zone 3:—"
oc @ Lap, # Rows
@
"ac
Number of Fasteners Per Insulation Board:
Zone 1':
Zone 1: Zone 2:
Zone 3:_
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc..
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16..
aT. LUCK
Section D (Steep Slope Roof System)
Roof System Manufacturer:
Notice of Acceptance Number: I -r)q L.
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations): ��,�� ,, ���
Zone 1`' 71 Zone 2e: Zone 2n: Zone 2r one 3e:�iZ6ne 3r:
Deck Type:
Type Underiayment:_
Roof Slope:
�-�- 12 Insulation: j
1
Fire Barrier:
Ridge Ventilation? Fastener Type & Spacing: fVf
�� �J a
Adhesive Type:
Type Cap Sheet: j
Mean Roof -Height..
Roof Covering:
Type & Size Drip
Edge: