HomeMy WebLinkAboutRegulator Specsa
Bulletin 71.1:R622
Type R622 Pressure Reducing Regulator
• Compact Design
Prote
Scree
ui, h 1---it
y
Relief
Veight
• Inlet and Outlet Pressure Gauge Taps
Figure r. Type P622 Pressure ReJuorng Re,il
Introduction
Type R622 direct -operated. sprang -loaded regulators
provide economical pressure reducing control in
a variety of residential, commercial. and industrial
FISHER
applications. These regulators can be used wsth
natural. manufactured, or propane gases and have the
same inlet and outlet pressure capabilities.
EMERSON
Bulletin 71.1: R622
Specifications
Body Size and End Connection Style0)
112 NPT inlet and outlet
Maximum Allowable Inlet Pressure0)
Operating: 125 psig (8.6 bar)
Emergency: 125 psig (8.6 bar)
Except 1.8 to 2.2-inches w.c. (4 to 5 mbar) spring
range which has operating and emergency
pressures of 60 psig (4.1 bar)
Maximum Allowable Outlet (Casing) Pressure(►
Operating to Avoid Internal Part Damage:
3 psid (0,21 bar d) above outlet pressure setting
Emergency: 20 psi (1,4 bar)
Outlet Pressure Ranges
See Table 1
Orifice Size
1/8-inch (3.2 mm) orifice
Flow Coefficients
Wide -Open CB for Relief Sizing: 12.5
Wide -Open C„ for Relief Sizing: 0.36
Cl: 35
IEC Sizing Coefficients
XT: 0.78
Fo: 0.82
FL: 0.89
Flow Capacities
See Table 2
Pressure Registration
Internal
Relief Performance
See Figure 4
Internal Relief Performance
Start -to -Discharge is 8 to 22-inches w.c.
(20 to 55 mbar) for setpoints from
1.8 to 20-inches w.c. (4 to 50 mbar)
Start -to -Discharge is 140 to 200% over setpoint
from 20-inches w.c. to 2.2 psig (50 to 152 mbar)
Spring Case Vent Connections
3/4 NPT with removable screen
Temperature Capabilities()
-20° to 160°F (-29° to 71 °C)
Approximate Weight
2.35 pounds (1 kg)
Construction Materials
Body, Spring Case, Diaphragm Plate, and
Orifice: Aluminum
Diaphragm, Disk, and O-ring: Nitrile (NBR)
Adjusting Screw and Pushpost: DelrinO
Closing Cap: ASA Thermoplastic (UV -Ray Resistant)
Control Spring: Zinc -plated steel
Machine Screw, Spring Seat,
and Lever: Zinc -plated steel
Valve Stem: Zinc
Relief Valve Spring, Relief Spring Retainer,
Lever Pin, and Vent Screen: Stainless steel
1. The amps n"BuMft cr"Vpkabd standard sr =Wn shouf0 Da Do Oxwedod
Devoe is a mark Owned by E 1. au Pont do NOMMM and Co.
In addition, Type R622 regulators have internal relief
across the diaphragm to help minimize overpressure.
Any outlet pressure above the start -to -discharge point
of the non-adjustable relief valve spring moves the
diaphragm off of the relief valve seat, allowing excess
pressure to bleed out through the screened spring
case vent.
Table 1. Outlet Pressure Ranges
Specifications
The Specifications section lists specifications for Type R622
Pressure Reducing Regulators. As it originally comes
from the factory, specifications for a given regulator
are stamped on the spring case nameplate.
OUTLET PRESSURE RANGE
CONTROL SPRING PART
NUMBER
CONTROL SPRING
COLOR CODE
SPRING WIRE DIAMETER,
INCHES (mm)
SPRING FREE LENGTH,
INCHES (mm)
1,8 to 22.1n ttes w.c (4 to 5 Mbw)
T144S3T0012
turpfe
0051(1.30)
340(66.4)
5 to 7-tndtes w t. (12 to 17 M=)
T 143981DO 12
Orange
0062(1,58)
340(86.4)
6 5 to 9-md►es w c. (16 to 22 mbar)
T 14399TOO12
veltow
0 067 (1,70)
3,61 (91,7)
9 to 134ndles W.C. (22 to 32 mbar)
T 14400T0012
Saw&
0072(1.83)
4.10 (104)
13 to 2G-tndtes w.c. (32 to 50 mbar)
T14401T0012
Gray
0080(2.03)
3.60 (91,4)
16 to 35-mdtes we (40 to 87 mbar)
T14402To012
Ptnk
0093(2.36)
3.52 (89,4)
1 to 22 pstg (69 to 152 mbar)
T14403T0012
Ltghl Blue
0105(2,67)
166 (93.0)