Loading...
HomeMy WebLinkAboutOWENS CORNING ASPHALT ROOF SHINGLESOwens Corning Evaluation Report 037940.02.12-1111 One Owens Corning Parkway FL10674-1116 Toledo, OH 43659 Date of Issuance: 02/06/2012 (740) 404-7829 Revision 11: 12/11/2020 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the Ph Edition (2020) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof Shingles LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted herein and FBC 1507.2.7.1 / R905.2.6.1 CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change. Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any changes to the product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words "NEMO I etc. Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 10. Prepared by: — Robert J.M. Nieminen P.E. �'•�, �, �t'�= The facsimile seal appearing was authorized by Robert Florida Registration No. 59166, Florida DCA ANE1983 Nieminen, P.E. on 12/11/2020. This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. NEW ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. ©2018 NEM0 ETC, LLC (NNEMOJetc. ROOFING SYSTEMS EVALUATION: Product Category: Roofing Sub -Category: Asphalt Shingles Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated compliance with the following sections of the 71 Edition (2020) Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. Section Property Standard Year 1507.2.4, R905.2.3 Physical Properties ASTM D1970 2015 1507.2.5, R905.2.4 Material standard ASTM D3462 2010 1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D3161 2016 1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D7158 2019 Entity Examination Reference Date Owens Corning Declaration Equivalency Declaration 08/06/2019 PRI(TST5878) ASTM D1970 OCF-382-02-01 10/24/2017 UL LLC (CER9626) Physicals & Wind Resistance File R2453, Vol. 3 02/15/2007 UL LLC (CER9626) Physicals & Wind Resistance 20120516-112453 05/16/2012 UL LLC (TST9628) Physical Properties 06CA20263 04/18/2006 UL LLC (TST9628) Wind Resistance 11CA34308 02/18/2012 UL LLC (TST9628) Physicals & Wind Resistance 4786093137 02/01/2014 UL LLC (TST9628) Wind Resistance 4786126532 02/10/2014 UL LLC (TST9628) Physical Properties Classification letter 02/13/2014 UL LLC (TST9628) Physical Properties Classification letter 10/02/2015 PRI (QUA9110) Quality Control Service Confirmation 04/05/2020 PRI (QUA9110) Quality Control Florida BCIS Current TABLE 1: ASPHALT SHINGLE COMPONENTS Type Product Plant(s) Material Description Standard Starter Strip Shingle H-TX, OR Starter Strip Plus MN, OR Accessory ASTM D3462 starter strips for asphalt roof shingles Starter SRS TopShield Starter MN, OR Strips Starter Shingle Roll NH ASTM D1970 mineral -surfaced, fiberglass -reinforced, self -adhering SBS modified bitumen starter Supreme. GA, CA, CO, I -TX, NJ, OH, ASTM D3462 fiberglass reinforced 3-tab asphalt TN, OR, IL roof shingles Berkshire* MN ASTM D3462 fiberglass reinforced, 4-tab asphalt roof shingles Duration' Premium CA, OR Duration* Premium COOL CA Asphalt TruDefinition° Duration' Shingles IN, CA, CO, I -TX, FL, NJ, OH, TruDefinition° Duration' Designer Color Collection MN, OR, GA, IL, TN ASTM D3462 fiberglass reinforced, laminated asphalt roof shingles Oakridge GA, IN, CA, CO, H-TX, I -TX, FL, NJ OH, TN TruDefinition° Oakridge° H-TX, I -TX WeatherGuard° HP TN NEMO ETC, LLC Evaluation Report 037940.02.12-Rll Certificate of Authorization #32455 77H EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16 Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020 Page 2 of 10 TABLE 1: ASPHALT SHINGLE COMPONENTS Type Product Plant(s) Material Standard Description Berkshire® Hip and Ridge Shingles with Sealant MN DuraRidgell Hip and Ridge MN Hip and fiberglass reinforced, hip and ridge Ridge Shingles with Sealant ASTM D3462 asphalt roof shingles ProEdge® GA, CA, OH, OR Shingles WeatherGuard® HP Hip and Ridge Shingles TN TABLE 2A: WIND CLASSIFICATIONS, ASPHALT SHINGLES I Product Supreme® Berkshire Duration` Premium Duration' Premium COOL TruDefinition® Duration` TruDefinition" Duration' Designer Color Collection TruDefinition® Oakridge° WeatherGuard` HP 5.5.1 Classification by ASTM D7158: FBC Table 1507.2.7.1 or R905.2.6.1 ASTM D3161(F) & ASTM D7158(H) ASTM D7158, Class H applies only to exposure category B or C and a building height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. NEMO ETC, LLC Evaluation Report 037940.02.12-1131 Certificate of Authorization #32455 7M EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116 Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020 Page 3 of 10 U(4 • I etc. TABLE 2B: WIND CLASSIFICATIONS, STARTER STRIPS AND HIP & RIDGE Type Product FBC Table 1507.2.7.1 or R905.2.6.1 Starter Strips Starter Strip Shingle ASTM D3161, Class F Starter Strip Plus SRS TopShield Starter Hip & Ridge Shingles Berkshire' Hip and Ridge Shingles with Sealant ASTM D3161, Class F DuraRidge® Hip and Ridge Shingles with Sealant ProEdge® WeatherGuard' HP Hip and Ridge Shingles 5.5.2 Refer to Owens Corning published information on wind resistance and installation limitations. 5.6 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3. Refer to the Product Approval of the component manufacturer for components that are produced by a Product Manufacturer other than the report holder on Page 1 of this Evaluation Report. 6.1 GENERAL: 6.1.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle manufacturer's minimum requirements. 6.1.2 Underlayment shall be acceptable to the shingle manufacturer and shall hold current Florida Statewide Product Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3. 6.1.3 Fasteners shall be in accordance with the shingle manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.1.4 Owens Corning asphalt shingles are acceptable for use in reroof (tear -off) or recover applications, subject to the limitations set forth in FBC Section 1511 or R908 and published installation instructions. 6.2 ACCESSORY STARTERS: 6.2.1 Installation of Starter Strip Shingle, Starter Strip Plus and SRS TopShield Starter shall comply with the Owens Corning current published instructions, using minimum five (5) nails per strip. Felt undedayment --Deck Self -adhered WeatherLoeke undedayment Drw__. edge r � � Dry edge Nails located 2 -3" from save Install first Self-sealing adhesive Starter Strip . • ' positioned along eave Shingle with 8"removed Starter, Strip shingle overhangs eaves and rakes Feb un"vnwa — Deck Sall -Ad eyed Weathertosk'� :f wtymenr �i Drip....... edge J1 r- imm i+a3a! rest Starter Strip P{xi • ' poeed 4xvg are e Starts Strip PW overhangs eaves and rakes 1/4 =314` Figure 1: Minimum Nailing, Starter Strip Figure 2: Minimum Nailing, Starter Strip Plus NEMO ETC, LLC Evaluation Report 037940.02.12-1111 Certificate of Authorization #32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116 Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020 Page 4 of 10 U(4 6.2.2 Installation of Starter Shingle Roll shall comply with the Owens Corning current published instructions. edge Starter Shingle Roll adhered directly to undedayment and primed drip edge Self-sealing adhesive positioned along eaves Figure 3: Starter Shingle Roll 6.3 ASPHALT SHINGLES: 6.3.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions: ➢ Berkshire® shingles require minimum five (5) nails per shingle. r WeatherGuard' HP shingles require minimum six (6) nails per shingle. Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required Refer to Owens Corning published information on wind resistance and installation limitations. 6.3.1.1 Supreme: Normal Mansard or Area pare Wind Areas High Wind desvenes y Area pare vientos normelas Areas vientos fuertes w 51Exposure Exposicidn Figure 4: Minimum Nailing, Supreme (Standard Size) Normal Mansard or Area par& Wind Areas High Mind dasvnnes y Area pare vientos normstas Areas vientos foartes to (A) t2 t T �• 2" (B) 2' t' 5 5/i9" Exposure Exposicidn Figure 5: Minimum Nailing, Supreme (Metric Size) NEMO ETC, LLC Evaluation Report 037440.02.12-1111 Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116 Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020 Page 5 of 10 6.3.1.2 Berkshire®: Figure 6: 5-Nail Pattern, Berkshire ONEMOletc. Sealant strip La tka de mhdar A 81h� • 8 ly • • 8 0 W, • 8 W, 't 1 ,N s 1. Figure 7: 6-Nail Pattern, Berkshire Figure 8: Mansard or Steep Slope Pattern, Berkshire NEMO ETC, LLC Evaluation Report 037940.02.12-1111 Certificate ofAuthorizotion #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 6 of 10 U(4 NEMO I etc. 6.3.1.3 Duration" Premium, TruDefinition" Duration, Duration® Premium COOL & TruDefinition' Duration' Designer Color Collection: 4-Nail Fastening Pattern SumNailO rastenfng area width Nall. 7WIMI 1" 12" e'.�e;rs Carruveg Svrstixb # ,� . <aanS Buw.sa� warq # Os¢rts Canttap Svra4ar�' # 6-118" F1 Figure 9: Standard 4-Nail Pattern, Duration Figure 10: 6-Nail Pattern, Duration Figure 11: Mansard or Steep Slope Pattern, Duration NEMO ETC, LLC Certificate of Authorization #32455 7i" EDITION (2020) FBC NON-HVHZ EVALUATION Owens Corning Asphalt Roof Shingles Evaluation Report 037940.02.12-Rll FL10674-R16 Revision 11: 12/11/2020 Page 7 of 10 6.3.1.4 TruDefinition* Oakridge", Oakridge®: 4 Nall Pattern Ekyuma con 4 davos 6 SAr Exposure Nails Eyposiddirt de 6 6/8 ptig cfams 'EWSi'ddiz Z glepdg. I Figure 12: Standard 4-Nail Pattern, Oakridge t#NEMO I etc. 6 Nall Pattom Euplema con 6 dms r Ir Nags 6 BAr Exposure chy0s 6 K %" Exposure Evosickin de 5 SIR Pdg. ExpostcOn do 5 510ptig. Figure 13: 6-Nail Pattern, Oakridge Fastening for Slopes Greater Than 21:12 SureNall& lastefflng area width Nall, Typical 12' t $41111" Four I" Spot& of Asphalt Roofing Cement ----------- 6.3.1.5 WeatherGuard® HP: Figure 14: Mansard or Steep -Slope Pattern, Oakridge 6 N al Pattern Esquema con 6 clavos Nail 6 118' from forum of shingle ilu 5 5V Exposure 6 Fasteners Clove a 6118 k. de b plate inferior te la t0a Exposici6n de 5 5,'8 pulig. 6 sujetadores 12- 1' NA O&M 5 Sig- Jr., 42'6X .'4 % le 58 pub Expaskidn d' 5 Wt. Figure IS: 6-Nail Pattern, WeatherGuard HP Four 1" Spotsof AspMk Roof Cement Cuatto puntas de cemento 6 techo de asfafto do 1 p*da Figure 16: Mansard or Steep -Slope Pattern, WeatherGuard HP MEMO ETC, LLC Evaluation Report 037940.02.12-Rll Certificate ofAuthorization #32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16 Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020 Page 8 of 10 NNEMOjetc. 6.4 HIP AND RIDGE SHINGLES: 6.4.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions. ➢ Berkshire* Hip and Ridge Shingles with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant require minimum two (2) nails per shingle. ➢ WeatherGuard' HP Hip and Ridge Shingles and ProEdge® require minimum four (4) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations. 6.4.1.1 Berkshire® Hip and Ridge with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant: Fig. A Prevailing Wind Direction �— Direccion del viento predominante 0 Nails P Clavos ----------- 1 I P 1 I I I I I I I Ir Fxp-re rwxm de8pal 0 P Figure 17: Isometric View, Berkshire and DuraRidge 6.4.1.2 WeatherGuard® HP Hip and Ridge Shingles: Fig. A 4 4 Pm aMgtgwind �— Directbn A A Nails 4 4 A 4 I � I I I I I I I s'—►I Etpoaure Figure 19: Isometric View, WeatherGuard HP Hip and Ridge Fig. B Top View Vista superior I) 1 Nail 2srs° Clavo Owens Coming Sirrca Sur~ I I CIw y) G l cc ti ( I 12" Figure 18: Plan View, Berkshire and DuraRidge Fig. G Hip & Ridge Shingle Fastening Top Vlswv Nails Nails T' T. Z 5' Exposure I 12, Figure 20: Plan View, WeatherGuard HP Hip and Ridge NEMO ETC, LLC Evaluation Report 037940.02.12-Rll Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16 Owens Corning Asphalt Roof Shingles Revision 11: 12/21/2020 Page 9 of 10 6.4.1.3 ProEdge®: PreveRing Wind Direction Sealant Strip A--"-- 6" Exposure Fasten 7Yz Cover Exposed Fasteners with Roof Cement Figure 21: Isometric View, ProEdge 2 1� 0 s Standard •-11e Fastening Pattern �u L 12' Sealant I 7 6" Expose ' 12" Figure 22: Plan View, ProEdge As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this product. Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements. Refer to Section 4 herein for products and production locations having met codified material standards. PRI Construction Materials Technologies, LLC— QUA9110 ; 813 621-5777; bwilson@pricmt.com - END OF EVALUATION REPORT - NEMO ETC, LLC Evaluation Report 037940.02.12-1111 Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116 Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020 Page 10 of 10