Press Alt + R to read the document text or Alt + P to download or print.

No preview available

The URL can be used to link to this page

Home My WebLink AboutAPPROVED PRODUCTAPPROVALSM1AMbDAbE + M14,Ml-DADE COUNTY DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) PRODUCT CONTROL SECTION 11805 Sty' 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.Eov/eeonomv Owens Corning Roofing and Asphalt, LLC One Owens Corning Parkway Toledo, OH 43659 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Duration®, Duration® Premium, TruDefinition® Duration®, and TruDeffnition® Duration® Designer Colors Collection LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No.16-0425.01 and consists of pages 1 through 6. The submitted documentation was reviewed by Freddy Semino ,.. NOA No.: 17-1211.02 Expiration Date: 07/19/21 Approval Date: 12/27/18 Page 1 of 6 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub -Category: Asphalt Shingles Materials: Laminate Deck Type: Wood SCOPE This approves a roofing system using Duration®, Durationg Premium, TruDefinition® Duration®, and TruDefinition® Duration® Designer Colors Collection asphalt shingles manufactured by Owens Corning as described in Section 2 of his Notice of Acceptance. PRODUCT DESCRIPTION Product Dimensions Test Specifications Product Description Duration® 13 '/4" x 39 3/8" Manufacturing Locations #l, 2 Duration® Premium; 13 '/4" x 39 3/8" TruDefinition® Duration®; TruDefinition® Duration® Designer Colors Collection Manufacturing Location #1, 2, 3, 4 Duration® Manufacturing Location #1, 2, 3 Duration® Premium; TruDefinition® Duration®; TruDefinition® Duration® Designer Colors Collection Manufacturing Location #1, 2, 3, 4,5,6,7 MANUFACTURING LOCATION 1. 2. 3. 4. 5. 6. 7. Jacksonville, FL Memphis, TN Savannah, GA Irving, TX Kearny, NJ Medina, OH Brookville, IN 13 1/4" x 39 3/8" 13 '/4" x 39 3/8" TAS 110 A heavy weight, fiberglass reinforced four tab asphalt shingle with continuous bead of sealant. TAS 110 A heavy weight, fiberglass reinforced four tab asphalt shingle with large nail area with continuous bead of sealant. TAS 110 A heavy weight, fiberglass reinforced four tab asphalt shingle with dashed bead of sealant. TAS 110 A heavy weight, fiberglass reinforced four tab asphalt shingle with dashed bead of sealant. NOA No.: 17-1211.02 N110.M1•DA[)E.GOiJNTY Expiration Date: 07/19/21 Approval Date: 12/27/18 Page 2 of 6 EVIDENCE SUBMITTED Test Agency Test Identifier Test Name/Report Date PRl Asphalt Technologies, Inc. OCF-157-02-01 TAS 100 10/26/10 OCF-156-02-01 TAS 100 10/26/10 OCF-163-02-01 TAS 100 12/10/10 OCF-164-02-01 TAS 100 12/10/10 OCF-172-02-01 TAS 100 05/26/11 OCF-179-02-01 TAS 100 02/02/12 OCF-367-02-01 TAS 100 11/08/17 OCF-368-02-01 TAS 107 11/08/17 OCF-371-02-01 TAS 100 11/08/17 OCF-372-02-01 TAS 107 11/08/17 OCF-375-02-01 TAS 100 11/08/17 OCF-376-02-01 TAS 107 11/08/17 Underwriters Laboratories, Inc. IONK13947 TAS 107 11/12/10 11CA15662 TAS 107 05/27/11 11NB21712 TAS 107 02/18/12 12CA12180 ASTM D3462 03/01/12 R2453 ASTM D3462 10/20/17 LIMITATIONS 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Shall not be installed on roof mean heights in excess of 33 ft. 3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. 4. INSTALLATION 1. Shingles shall be installed in compliance with Roofing Application Standard RAS 115. 2. Flashing shall be in accordance with Roofing Application Standard RAS 115 3. The manufacturer shall provide clearly written application instructions. 4. Exposure and course layout shall be in compliance with Detail 'A', attached. 5. Nailing shall be in compliance with Detail 'B', attached. LABELING Shingles shall be labeled with the Miami -Dade Seal as seen below, or the wording "Miami -Dade County Product Control Approved". MIAMPEADE COUMTY ® e NOA No.: 17-1211.02 Expiration Date: 07/19/21 Approval Date: 12/27/18 Page 3 of 6 BUILDING PERMIT REQUIREMENTS l . Application for building permit shall be accompanied by copies of the following: 1.1 This Notice of Acceptance. 1.2 Any other documents required by the Building Official or the applicable code in order to properly evaluate the installation of this system. L1 • iC Fast CO&M NOA No.: 17-1211.02 N�lAhtt:•t3RtaE.S:0UNTIf Expiration Date: 07/19/21 Approval Date: 12/27/18 Page 4 of 6 u�� (SEALANT MAY BE CONTINUOUS OR DASHED. NOT SHOWN IN THE DETAIL DRAWINGS) rfir tr: r e' MAXIMUM SLOPE 21:12 r - a r r Exposickin K pulg, NOA No.: 17-1211.02 Expiration Date: 07/19/21 Approval Date: 12/27/18 Page 5 of 6 SLOPE GREATER THAN 21:12 AFFRO i NOA No.: 17-1211.02 Expiration Date: 07/19/21 Approval Date: 12/27/18 Page 6 of 6 UL Product i TM a TGAM.R2453 - Roof -covering Materials, Impact Resistance Roof -covering Materials, Impact Resistance See General Information for Roof -covering Materials, Impact Resistance OWENS CORNING ROOFING AND ASPHALT, LLC R2453 One Owens Corning Parkway Toledo, OH 43659 USA Class 4 Asphalt glass fiber mat shingles, Model(s) ProEdge FLEX Hip and Ridge, ProEdge STORM Hip and Ridge, TruDefinition Duration Flex, TruDefinition Duration Storm, TruDefinition WeatherGuard HP, WeatherGuard HP Last Updated on 2020-04-15 The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow -Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow -Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non -misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "© 2021 UL LLC" "IAMM mow MIAMI-DADE COUNTY DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy Polyglass USA, Inc. 150 Lyon Drive Fernley, NV 89408 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Polyglass Self -Adhered Roof System over Wood Decks LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA# 17-1016.01 and consists of pages 1 through 38. The submitted documentation was reviewed by Alex Tigera. NOA No.: 19-0311.04 Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 1 of 38 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub -Category: Modified Bitumen Materials SBS/APP/TPO Deck Type: Wood Maximum Design Pressure -112.5 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description Polyanchor 250' x 48" ASTM D 4601, A polymer woven, high performance, synthetic base Type II sheet. Polyglass G2 Base 108' x 36" ASTM D 4601, Asphalt -coated fiberglass reinforced base sheet Type 11 Elastoshield HT 65' 8" x 3' 3-3/8" ASTM D 6162 SBS modified asphalt coated fiberglass/polyester reinforced base sheet. XtraFlex SBS HT 65' 8" x 3' 3-3/8" ASTM D 6162 SBS modified asphalt coated fiberglass/polyester Base 650 reinforced base sheet. Elastobase 65' 2" x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced Type I base sheet. Elastoflex SA V 66' 8" x 3' 3-3/H" ASTM D 6163, Self -adhered, fiberglass reinforced, SBS modified Type I bitumen membrane with a self -adhering back face and a smooth top surface. Elastoflex SA V FR 66' 8" x 3' 3-3/8" ASTM D 6163, Self -adhered, fire -rated, fiberglass reinforced, SBS Type I modified bitumen membrane with a self -adhering back face and a smooth top surface. Elastoflex SA V 66' 8" x 3' 3-3/8" ASTM D 6163, Self -adhered, fiberglass reinforced, SBS modified PLUS Type I bitumen membrane with a self -adhering back face and a smooth top surface. Elastoflex SA V 66' 8" x 3' 3-3/8" ASTM D 6163, Self -adhered, fire -rated, fiberglass reinforced, SBS PLUS FR Type I modified bitumen membrane with a self -adhering back face and a smooth top surface. XtraFlex SBS Base 66' 8" x 3' 3 3/s" ASTM D 6163, Self -adhered, fiberglass reinforced, SBS modified SA Type I bitumen membrane with a self -adhering back face and a smooth top surface. XtraFlex SBS Glass 65' 8" x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced Base Type I base sheet. Elastobase P 65' 8" x 3' 3-3/8" ASTM D 6164, SBS modified asphalt coated polyester reinforced base Type I sheet. Elastoflex SA P 32' 10" x 3' 3-3/8" ASTM D 6164, Self -adhered, fiberglass reinforced, SBS modified Type I bitumen membrane with a self -adhering back face and a granule top surface. rt"WAneCounm NOA No.: 19-0311.04 e Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 2 of 38 Elastoflex SA P FR 32' 10" x 3' 3-3/8" ASTM D 6164, Self -adhered, fire -rated, polyester reinforced, SBS Type I modified bitumen membrane with a self -adhering back face and a granule top surface. Polyfresko G SBS SA 32' 10" x 3' 3 14" ASTM D 6164, Self -adhered, fiberglass reinforced, SBS modified Type I bitumen membrane with a self -adhering back face and a granule top surface. Polyfresko G SBS SA 32' 10" x 3' 3 3/8" ASTM D 6164, Self -adhered, fire -rated, fiberglass reinforced, SBS FR Type I modified bitumen membrane with a self -adhering back face and a granule top surface. Polyreflect 32' 10" x 3' 33/8" ASTM D 6164, Self -adhered, polymer, SBS modified bitumen Type I membrane with a self -adhering back face and a smooth top surface. XtraFlex SBS G SA 32' 10" x 3' 3-3/8" ASTM D 6164, Self -adhered, fire -rated, polyester reinforced, SBS Type I modified bitumen membrane with a self -adhering back face and a granule top surface. Polybond 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Polyflex 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. XtraFlex APP S 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. PolyKool 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified Type I bitumen membrane with a self -adhering back face and a white film laminate on the top surface. XtraFlex Kool APP S 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified SA Type 1 bitumen membrane with a self -adhering back face and a white film laminate on the top surface. Polyflex SA P 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified Type I bitumen membrane with a self -adhering back face and a granule top surface. Polyflex SA P FR 32' 10" x 3' 3-'/8" ASTM D 6222, Self -adhered, fire -rated, polyester reinforced, APP Type I modified bitumen membrane with a self -adhering back face and a granule top surface. Polyfresko G APP SA 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified Type I bitumen membrane with a self -adhering back face and a granule top surface. Polyfresko G APP SA 32' 10" x 3' 3-;/8" ASTM D 6222, Self -adhered, fire -rated, polyester reinforced, APP FR Type I modified bitumen membrane with a self -adhering back face and a granule top surface XtraFlex APP G SA 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, fire -rated, polyester reinforced, APP Type I modified bitumen membrane with a self -adhering back face and a granule top surface. IRIMIRL r�uahtFnaoe a 5UNW-M NOA No.: 19-0311.04 •now Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 3 of 38 Polyglass APP Base 65' 8" x 3' 3 3/A" ASTM D 6509, APP modified asphalt coated fiberglass reinforced Type I base sheet. PG 100 1, 3, 5, 50, 55 gal, ASTM D41 A penetrating solution of solvent and a blend of tube or 17 oz. spray selected asphalts used to promote adhesion. can PG 350 1, 3, 5, 50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with tube Type III modified bitumen membranes. PG 400 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use in tube ASTM D3409 dry or damp conditions. PG 425 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use in tube ASTM D3409 dry or damp conditions. PG 450 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement. tube PG 500 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use tube with modified bitumen membranes. POLYPLUS 35 1, 3, 5, 50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with tube Type III modified bitumen membranes. POLYPLUS 45 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement. tube POLYPLUS 50 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use tube with modified bitumen membranes. XtraFlex 10 1, 3, 5, 50, 55 gal, ASTM D41 A penetrating solution of solvent and a blend of tube or 17 oz. spray selected asphalts used to promote adhesion. can XtraFlex 35 1, 3, 5, 50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with tube Type III modified bitumen membranes. XtraFlex 50 Premium 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use Modified Wet/Dry tube with modified bitumen membranes. Cement WB-3000 5 gallon pail Proprietary A low-VOC, water -based acrylic primer to enhance adhesion of self -adhered membranes. Immak Mu►rtFOEwE cour�rY NOA No.: 19-0311.04 "' a Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 4 of 38 APPROVED INSULATIONS: TABLE 2 Product Name Product Description Manufacturer (With Current NOA) Polytherm-H Polyisocyanurate foam insulation Polyglass USA, Inc. Polytherm Polyisocyanurate foam insulation Polyglass USA, Inc. Polytherm G Polyisocyanurate foam insulation Polyglass USA, Inc. XtraFlex Polyiso Polyisocyanurate foam insulation Polyglass USA, Inc. XtraFlex Polyiso G Polyisocyanurate foam insulation Polyglass USA, Inc. ACFoam-II Polyisocyanurate foam insulation Atlas Roofing Corp ACFoam-III Polyisocyanurate foam insulation Atlas Roofing Corp Structodek High Density Fiberboard Roof Wood fiber insulation board Blue Ridge Fiberboard, Inc. Insulation DensDeck, DensDeck Prime Gypsum insulation board Georgia-Pacific Gypsum LLC H-Shield Polyisocyanurate foam insulation Hunter Panels, LLC H-Shield CG Polyisocyanurate/perlite composite insulation Hunter Panels, LLC ENRGY-3 Polyisocyanurate foam insulation Johns Manville Corp. Fesco Board Expanded mineral fiber Johns Manville Corp. Multi -Max FA-3 Polyisocyanurate foam insulation Rmax Operating, LLC. SECUROCK Gypsum -Fiber Roof Board Fiber reinforced coverboard United States Gypsum Corporation IffMIAMMADE CONOA No.: 19-0311.04 ' "o ►UNTY Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 5 of 38 APPROVED FASTENERS: Fastener Number 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 17 18 TABLE 3 Product Product Name Descrimtion Dekfast DF-#12-PH3 Insulation fastener for wood, steel and concrete decks Dekfast DF-#14-PH3 Insulation fastener for wood, steel and concrete decks Dekfast DF-# 15-PH3 Insulation fastener for wood, steel and concrete decks Dekfast PLT-H-2-7/8 Galvalume hex stress plate. #14 Roofgrip Insulation and membrane fastener Flat Bottom Metal Plate A2-SS aluminized steel plate Trufast #14 HD Fastener Insulation fastener for steel and wood decks Trufast 3" Metal Insulation Round Galvalume AZ50 steel Plate plate Polygrip Fasteners #12 Insulation fastener for wood, steel and concrete decks Polygrip Fastener #14 Insulation fastener for wood, steel and concrete decks Polygrip Fastener 415 Insulation fastener for wood, steel and concrete decks Polygrip Hex Plates Galvalume hex stress plate. OMG 3 in. Ribbed Galvalume stress plate. Galvalume Plate (Flat) OMG 3" Galvalume Steel Galvalume stress plate. Plate Dekfast PLT-R-3 Galvalume stress plate. Millennium One -Step A two component, low rise, Foamable Adhesive polyurethane foam adhesive Millennium One Step Green A two component, low rise, Foamable Insulation polyurethane foam adhesive Adhesive Millennium PG-1 Pump A two component, low rise, Grade Adhesive polyurethane foam adhesive APPROVED Manufacturer Dimensions (With Current NOA) SFS Group USA, Inc. Various SFS Group USA, Inc. Various SFS Group USA, Inc. 2 7/8" x SFS Group USA, Inc. 3 '/4" Various OMG, Inc. 3" square OMG, Inc. Altenloh, Brinck & Co. U.S., Inc. 3.23 round Altenloh, Brinck & Co. 3" round U.S., Inc. Various Polyglass USA, Inc Various Polyglass USA, Inc. Various Polyglass USA, Inc. 2 7/8" x Polyglass USA, Inc 3 '/4" 3" round OMG, Inc. 3" round OMG, Inc. 3" round SFS Group USA, Inc. Adco Products, Inc. dba Royal Adhesives & Sealants Adco Products, Inc. dba Royal Adhesives & Sealants Adco Products, Inc. dba Royal Adhesives & Sealants NOA No.: 19-0311.04 Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 6 of 38 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 1. Gravel To be installed in a flood coat 400 lbs/sq N/A Generic of approved asphalt at 60 lbs/sq 2. Slag To be installed in a flood coat 300 lbs/sq N/A Generic of approved asphalt at 60 lbs/sq 3. KM Acryl 15 A premium white or tinted 1-1 %2 gal/sq ASTM D6083 Polyglass USA, elastomeric acrylic based roof Inc. coating (water -based). A polyester fabric may be used for reinforcement with this coating. 4. KM Acryl 15 QS A premium white or tinted quick setting, elastomeric acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. 1-1'/2 gal/sq ASTM D6083 Polyglass USA, Inc. 5. KM Acryl 25 A premium white or tinted l-1'/2 gal/sq ASTM D6083 Polyglass USA, elastomeric acrylic based roof Inc. coating (water -based). A polyester fabric may be used for reinforcement with this coating. 6. KM Acryl 25 QS A premium white or tinted 1-1'/2 gal/sq ASTM D6083 Polyglass USA, quick setting, elastomeric Inc. acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. 7. KM -PS 4220 A single component, solvent, 1.25 gaUsq ASTM D6694 Polyglass USA, white or tinted, silicone Inc. coating. 8. KM -PS #250 A premium grade high solids, 1.25 gaUsq ASTM D6694 Polyglass USA, white or tinted, single Inc. component, moisture cure, fluid applied silicone coating APPROVED NOA No.: 19-0311.04 Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 7 of 38 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 9. PG 300 An asphalt cutback fibered roof 1 %2-2 gal/sq ASTM D4479 Polyglass USA, coating. May be applied by Inc brush or spray equipment to rejuvenate aged BUR 10. PG 600 Non-fibered aluminum roof %2-1 gal/sq ASTM D2824 Polyglass USA, coating. Type I Inc 11. PG 650 12. PG 700 13. PG 700 QS 14. PG 800 15. PolyBrite 70 16. PolyBrite 70 QS 17. PolyBrite 90 APPROVED Fibered aluminum roof coating. 1 %2-2 gal/sq A premium white or tinted elastomeric acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. A premium white or tinted quick setting, elastomeric acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. An asphalt based, non-fibered clay emulsion A premium white or tinted elastomeric acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. A premium white or tinted quick setting, elastomeric acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. A premium grade high solids, white or tinted, single component, moisture cure, fluid applied silicone coating 1-1'/z gal/sq 1-1 % gal/sq ASTM D2824 Polyglass USA, Type III Inc. ASTM D6083 Polyglass USA, Inc. ASTM D6083 Polyglass USA, Inc. 3 gal/sq in two ASTM D1227 Polyglass USA, coats Inc. 1-1 %2 gal/sq ASTM D6083 Polyglass USA, Inc. 1-1'/2 gal/sq ASTM D6083 Polyglass USA, Inc. 1.25 gal/sq ASTM D6694 Polyglass USA, Inc. NOA No.: 19-0311.04 Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 8 of 38 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 18. PolyBrite 95 A single component, white or 1.25 gaUsq ASTM D6694 Polyglass USA, tinted, solvent, moisture cure Inc silicone coating. 19. POLYPLUS 60 Non-fibered aluminum roof %2-1 gal/sq ASTM D2824 Polyglass USA, coating. Type I Inc. 20. POLYPLUS 65 Fibered aluminum roof coating. 1 %2-2 gal/sq ASTM D2824 Polyglass USA, Type III Inc. 21. XtraFlex 60 Aluminum Non-fibered aluminum roof t/2-1 gal/sq ASTM D2824 Polyglass USA, Roof Coating coating. Type I Inc. 22. XtraFlex 65 Aluminum Fibered aluminum roof coating. 1'h-2 gal/sq ASTM D2824 Polyglass USA, Roof Coating Fibered Type III Inc. 23. XtraFlex 70 Premium A premium white or tinted 1-1 %2 gal/sq ASTM D6083 Polyglass USA, Acrylic FR Roof elastomeric acrylic based roof Inc. Coating coating (water -based). A polyester fabric may be used for reinforcement with this coating. 24. XtraFlex 80 Emulsion An asphalt based, non-fibered 3 gal/sq in two ASTM D1227 Polyglass USA, Roof Coating clay emulsion coats Inc. 25. XtraFlex 30 An asphalt cutback fibered roof 1 %2-2 gal/sq ASTM D4479 Polyglass USA, Bituminous Roof coating. May be applied by Inc. Coating Fibered brush or spray equipment to rejuvenate aged BUR 26. XtraFlex SRC 8000 A single component, white or 1.25 gaUsq ASTM D6694 Polyglass USA, tinted, solvent, moisture cure Inc silicone coating. 27. XtraFlex SRC 9600 A premium grade high solids, 1.25 gaUsq ASTM D6694 Polyglass USA, white or tinted, single Inc component, moisture cure, fluid applied silicone coating monk arwrrFaEwe courm NOA No.: 19-0311.04 I Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 9 of 38 EVIDENCE SUBMITTED: Test Agency Test Name/Report Report No. Date Factory Mutual Research 4470 2W7A7.AM 08.04.94 Corporation 4450 2D5A9.AM 06.22.99 4470 3000857 01.12.00 4470 3004091 01.12.00 4470 3001334 02.15.00 4470 3014692 08.05.03 4450 3014751 08.27.03 4450 3019317 06.30.04 4470 3024311 11.01.06 4470 3012321 07.29.07 4470 3036182 07.31.09 4470 RR202591 10.22.15 Trinity ERD TAS 114 11752.09.99-1 02.08.00 TAS 114 11751.05.03 05,30.03 TAS 117(B)-ASTM D903 020841.06.04 06.02.04 TAS 114 02762.03.05 03.30.05 TAS 114 02764.09.05 09.09.05 TAS 114 P1739.01.07 01.23.07 TAS 114 P1734.07.06-R1 02.27.07 TAS 117(B)-ASTM D6862 C8500SC.11.07 11.30.07 TAS 114 & FM 4470 P7864SC.11.07 11.30.07 TAS 114(D) — ASTM D1876 P10070.10.08 10.09.08 TAS 114 (H) P13760.09.09 09.10.09 FM 4470 & TAS 114 P33970.03.11 03.15.11 ASTM D6163 / ASTM D 4601 P33960.03.11 03.15.11 ASTM D6163 P37590.03.13-2-R1 02.05.13 ASTM D6164 P37590.03.13-3A 03.06.13 TAS 114 P1738.02.07-R2 04.29.13 TAS 114 & TAS 117 (B) 11757.04.01-1-R1 04.30.13 ASTM D6509 P37590.03.13-1-R1 06.26.13 ASTM D6222 P37590.03.13-5-R1 07.01.13 ASTM D6164 P37590.07.13-1 07.02.13 TAS 114 & FM 4474 P41630.08.13 08.06.13 ASTM D4601 / TAS 117 P45940.09.13 09.04.13 ASTM D6222 P37590.09.13 09.12.13 ASTM D4601 / TAS 117 P45970.05.14 05.12.14 ASTM D6162 SC5170.05.15 05.08.15 ASTM D6162 SC5170.12.15-1 12.29.15 TAS 114 & FM 4474 PLYG-SC8905.05.16-1 05.17.16 TAS 114 & TAS 117 (B) 11757.12.00-1-R2 04.05.17 PRI Construction Materials ASTM D6222 PUSA-061-02-02 01.28.08 Technologies ASTM D6163 PUSA-064-02-02 02.27.08 ASTM D6222 PUSA-062-02-02 12.04.08 ASTM D6694 PUSA-134-02-01 05.16.14 MIAMI-DADE COuf+rt r NOA No.: 19-0311.04 mmlEmmmOr Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 10 of 38 EVIDENCE SUBMITTED: Test Agency Test Name/Report Report No. Date ASTM D6694 PUSA-135-02-01 05.16.14 TAS 117(B) PUSA-202-02-01 05.08.17 FM 4470 & TAS 114 PUSA-202-02-02 05.23.17 mmakh MIAr1aDEwE cOurmr NOA No.: 19-0311.04 "a o Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 11 of 38 Membrane Type: SBS/APP Deck Type 1: Wood, Non -Insulated Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c. or 48 wood screws at 6" o.c. System Type E(1): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8" o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet. Ply Sheet: ` One or mare plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V PLUS FR or XtraFlex SBS Base SA self -adhered. Membrane: One ply of Elastoflex SA P,LElastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR, PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA self -adhered. 5swurLuing,Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) ' required fire classification. Maximum Design Pressure: -52.5 psf, (See General limitation 47.). MtWtbADE C6UNTY NOA No.: 19-0311.04 "' • Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 30 of 38 WOOD DECK SYSTEM LIMITATIONS: 1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be Tx T maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf. 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 lbf. insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. END OFT IS ACCEPTANCE rnUUManaue Couner7r NOA No.: 19-0311.04 UJUNU19e Expiration Date: 10/11/22 Approval Date: 03/21/19 Page 38 of 38 Base Sheet: — One or more layers "Duflex", "XtraFlex APP S" or "Polyflex", heat fused or mechanically fastened; or one or more layers "Elastobase", "Elastobase Vented Base", "XtraFlex SBS Glass Base", "ElastoFlex V", "XtraFlex SB5 Glass Interply" or "ElastoFlex V-C", hot mopped or heat fused; or Type G2, hot mopped or mechanically fastened. Ply Sheet (Optional):— One or more layers "Duflex", "XtraFlex APP S" or "Polyflex", heat fused; or one or more layers "Elastobase", "Elastobase Vented Base", "XtraFlex SBS Glass Base", "ElastoFlex V% "XtraFlex SBS Glass Interply" or "ElastoFlex V-C", hot mopped or heat fused; or one or more layers Type G2, hot mopped or mechanically fastened. Membrane: — "Duflex G FR", "XtraFlex APP Dual", "Polyfresko G FR", "XtraFlex APR G FR% "XtraFlex APP G HP" or "Polyflex G FR" (modified bitumen), heat fused. 18. Deck C-15/32 incline: 1/2 insulation: — Polyisocyanurate (2-in. thick minimum), Glass fiber (15/16-in. thick minimum), perlite/polyisocyanurate composite, perlite/urethane composite (2-in. thick minimum). Base Sheet — One or more layers "Duflex", "XtraFlex APP S" or "Polyflex", heat fused or mechanically fastened; or one or more layers "Elastobase", "Elastobase Vented Base", "XtraFlex SBS Glass Base", "ElastoFlex V", "XtraFlex SBS Glass Interply" or Type G2, hot mopped or mechanically fastened. Ply Sheet (Optional): — One or more layers "Duflex", "XtraFlex APP S" or "Polyflex", heat fused; or one or more layers "Elastobase", "Elastobase Vented Base", "XtraFlex SBS Glass Base", "ElastoFlex W, "XtraFlex SBS Glass Interply", "ElastoFlex V-C" or Type G2, hot mopped or mechanically fastened. Membrane: — "ElastoFlex S6 G", "ElastoFlex S6 G-C" or "Polyfresko G SBS" (modified bitumen), hot mopped. 19. Deck C-15/32 incline: 1 Insulation: — Minimum 1/4 in- thick Georgia-Pacific Gypsum LLC "DensDeck® Roofboard" or "DensDeck Primee Roofboard" or "DensDeck DuraGuardTM' Roofboard", or 1-in. thick perlite, wood fiber or Glass fiber, mechanically fastened. Ply Sheet: — Type G2, mechanically fastened. Membrane: — "Polyflex" or "XtraFlex APP S", heat welded. Surfacing: — Monsey Products "Endure Aluminum Roof Coating", "Weather Check" or "Pro -Grade Aluminum Roof Coating" applied at 1-1/2 gal./100-ftz; or Brewer Co "Fortress 5001 Asphalt Emulsion" applied at 4-gal./100-ftz., followed by "PolyFlus 60", applied at 3/4 to 1 gal./100-ft2 20. Deck C-15/32 Incline: 2-1/2 Barrier Board: — Minimum 1/4 in. thick Georgia-Pacific Gypsum LLC "DensDecke Roofboard" or "DensDeck Primee Roofboard" or "DensDeck DuraGuard'`"' Roofboard" with all buttjoints staggered a minimum of 6-in. from the plywood roof deck joints. Base Sheet — Type G2, mechanically fastened- embrane: — "Polyflex G FR", "XtraFlex APP G HP", "XtraFlex APP G FR" or "Polyfresko G FR", heat fused. 21. Deck C-15/32 Incline: 2 insulation (Optional): — Polyisocyanu rate, perlite, wood fiber or polyisocyanurate/perlite board, any thickness. Barrier Board: — Minimum 1/4 in. thick Georgia-Pacific Gypsum LLC "DensDecke Roofboard" or "DensDeck Primee Roofboard" or "DensDeck DuraGuard-1 Roofboard", mechanically fastened with all butt joints staggered a minimum of 6-in. from the plywood roof deck joints. Base Sheet: — "Elastobase", "XtraFlex SBS Glass Base" (poly/sand), mechanically fastened or "ElastoFlex SA V Plus FR", "ElastoFlex SA V FR" or "ElastoFlex SA V FR Base Vent" (self -adhered). Ply Sheet (Optional): — "Elastobase", "XtraFlex SBS Glass Base"(poly/sand), heat fused or mechanically fastened, or "ElastoFlex SA V Pius FR", "ElastoFlex SA V FR" or "ElastoFlex SA V FR Base Vent", (self -adhered). Membrane: — "Polyflex SA P FR", "Polyfresko G SA P FR", "ElastoFlex SA P FR", "Polyfresko G SBS $A P FR", "ElastoFlex SA V FR HT', (self -adhered) or "Polyflex G FR", "XtraFlex APP G HP", "XtraFlex APP G FR", "Polyfresko G FR", "Duflex Flex SBS "XtraFlex APP Dual", "ElastoFlex S6 G FR% "Polyfresko G SBS FR% "ElastoFlex VG FR', "XtraFlex SBS POLY G", " POLY G T', "XtraFlex SBS Glass G", "XtraFlex SBS Glass GT" or "Elastoshield TS G FR", heat fused. Incline: 1/2 22. Deck C-15/32 Insulation (Optional):— Polyisocyanurate 1-1/2 in. thick (minimum) with all joints staggered 6-in. (minimum) from the plywood joints. Base Sheet —Type G2, mechanically fastened followed by "Elastobase", "Elastobase Vented Base" or "XtraFlex SBS Glass Base", mechanically fastened. Ply Sh (Optiona — "ElastoFlex SA V Plus FR", "ElastoFlex SA V FR" or "ElastoFlex SA V FR Base Vent", (self -adhered). Membrane: — "Polyflex SA P FR", "Polyfresko G SATTZ7, "ElastoFlex SA P FR", "Polyfresko G SBS SA P FR", or "Duflex G FR", "XtraFlex APP Dual", "Polyflex G FR", "XtraFlex APP G HP", "XtraFlex APP G FR", "ElastoFlex S6 G FR", "Polyfresko G SBS FR", "ElastoFlex VG FR", "XtraFlex SBS POLY G", "XtraFlex SBS POLY G T", "XtraFlex SBS Glass G", "XtraFlex SBS Glass GT" or "Elastoshield TS G FR", heat fused. 23. Deck NC Incline: 2 insulation (Optionap: — "Polytherm ® " or Atlas Roofing Corp. "ACFoam iII" or "ACFoam II" or Hunter Panels "H-Shield", any thickness. Base Sheet — "Elastobase", "XtraFlex SBS Glass Base"(poly/sand), heat fused or mechanically fastened or "ElastoFlex SA V FR", "ElastoFlex SA V Pius FR" or "ElastoFlex SA V FR Base Vent", (self -adhered). Membrane: — " Polyflex SA P FR", "Polyfresko G SA P FR", "ElastoFlex SA P FR", "Polyfresko G SBS SA P FR% "ElastoFlex SA V FR HT", (self -adhered) or "Polyflex G FR% "XtraFlex APP G HP% "XtraFlex APP G FR", "Polyfresko G FR", "XtraFlex APP Dual", "Duflex G FR% "ElastoFlex S6 G FR", "Polyfresko G SBS FR", "ElastoFlex VG FR", "XtraFlex SBS POLY G", "XtraFlex SBS POLY G 7, "XtraFlex SBS Glass G", "XtraFlex SBS Glass GT" or " Elastoshield TS G FR", heat fused. 24. Deck C-15/32 Incline: 3 Insulation (Optional): — Polyisocyanurate, perlite, wood fiber or polyisocyanurate/perlite board, any thickness. Barrier Board: — Minimum 1/4 in. thick Georgia-Pacific Gypsum LLC "DensDeck® Roofboard" or "DensDeck Prime® Roofboard" or "DensDeck DuraGuardT"` Roofboard", mechanically fastened with all buttjoints staggered a minimum of 6-in. from the plywood roof deckjoints. Sam Sheet — "Elastobase", "XtraFlex SBS Glass Base" (poly/sand), mechanically fastened. Ply Sheet (Optional): —' ElastoFlex SA V Pius FR", "ElastoFlex SA V FR" or "ElastoFlex SA V FR Base Vent", (self -adhered). Membrane: — "ElastoFlex S6 G FR", "XtraFlex SBS POLY G", "XtraFlex SBS POLY G T" or "Polyfresko G SBS FR", heat fused. 25. Deck NC Incline: 3 Insulation (Optional): — "Polytherm" or Atlas Roofing Corp. "ACFoam III" or "ACFoam 11" or Hunter Panels "H-Shield", any thickness. Barrier Board (Optional): — Minimum 1/4 in. thick Georgia-Pacific Gypsum LLC "DensDeck® Roofboard" or "DensDeck Prime® Roofboard" or "DensDeck DuraGuard' Roofboard", mechanically fastened. Base Sheet — "ElastoFlex SA V Plus FR", "ElastoFlex SA V FR" or "ElastoFlex SA V FR Base Vent" (self -adhered). Membrane: — "Polyflex SA P FR", "Polyfresko G $A P FR% "ElastoFlex SA P FR" or "Polyfresko G SBS SA P FR" (self - adhered). 26. Deck NC incline: 1/2 Base Sheet: — Type Gi or Type G2, mechanically fastened. Membrane: — "Polyflex G", "XtraFlex APP G HP TOR", "XtraFlex APP G" or "Polybond G", heat fused. 27. Deck NC Incline: 3 Membrane: — "Polyflex SA P FR", "Polyfresko G SA P FR% "Polyfresko G SBS SA P FR"or "ElastoFlex SA P FR" (self - adhered). 28. Decic NC Incline: 1 insulation (Optional): — Polyisocyanurate, any thickness. Barrier Board (Optional): — Minimuml/2 in. thick gypsum board or minimum 1/4 in. thick Georgia-Pacific Gypsum LLC "DensDeck® Roofboard" or "DensDeck Prime® Roofboard" or "DensDeck DuraGuardTM Roofboard" or minimum 1/4-in. thickUnited States Gypsum Co. "SECUROCKTM Roof Board Type FRX-G".