HomeMy WebLinkAboutAPPROVED Roof InfoST. LUCIE
Section A (General lnformation)
Master Permit No. process No.
contractors *.n,". Packard Roofing & Waterpoofing,lil&r" s cccA17517
,oo ooor"r, 120 E' ArborAvenue
ROOF CATEGORY
E Low Slope E Mechanically Fastened Tile tr Mortar/Adhesive Set Tiles
ftsohattic Shingles EI Metal panel/shingles Ewood shingleslshakes
[3 Prescriptive BUR-RAS 150
ROOF ROOF TYPE
E New roof E Repair EI Maintenance (aeroofing E Recovering
, ROOF SYSTEM INFORMATION
Low Slope Roof Area tsrt 50O Steep Sloped Roof Area (sF) lt 0b rotat(sF) ,qOh
Section B (Roof Plan)
Sketch Roof Plan: lllustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
lnclude dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
I
See c"+taCl'tfu{
)rq$rcl^1
PI Dian ram
Ridge
-
High Drip
Hip
Valley
Eave
Rake
Parapei
Protrusion
Apron Flashing - -
StepFlashinS ---
Pitch Change
To improve readability the lengths displayed in this diagram are rounded to the nearest whole number. Lengths under 4 feet are omitted for clarity.
484 0:12
391 3:12
391 3:12C
D 277 3:12
259 3:12
33 3:12
12 9:12
0 :12 3:12 I"12
o.24.9 13.5
5o/o0o/o 10o/o 12o/o 15%20o/o
18.5 19.4 24.7 21.3 22.220.3
The waste factors presented in the table are simple calculations based on the total area of the roof. They do not include any other roofing elements such as ridge, valley or hips
Use your best judgement and past experience to select the waste factor that works best for this particular roof.
Facet Sq.Ft. Pitch
AREA BY PITCH (in
WASTE FACTOR TABLE (in squares, includes pitched and flat totals)
-
ST LUCIE
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(lf a component is not used, identifu as ,,NA"l ^
systemManufacturer:-
-
PO tVg lA$
Product Approval No.:
Design Wind Pressures, From RAS 129 Or Calculations:
IZonel': J Zonel:_Zonel: Zone3:
Max. Design Pressure, from the specific product approval
system:
Deck:
rvp.' P ltlDo0d
Gauge Thickn"rr, I "
Slope, b
Anchor/Base sheet & N o. ar ery(sl:&_ilAAffi"X-r sftv
.Anchor/B_ase Sheet Fasten er / Bonding Material:
Insulation Base Layer:
Base lnsultation Size and Thickness, fV A
Base lnsulation Fastener/Bonding Material:
AJA.
Top lnsulation Size and Thickness: il *-
Top. I nsulation Fastener/Bonding Material:Nft
Base Sheet(s) & No. of ply(s):
Base Sheet Fastener/Bonding Material:
Ply Sheet(s)' & No. of Ply(s):
ropPry: ?rtU€te{ jnP
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':_" oc @ Lap, # Rows_ @ _n oD .
^, Zone 1:-" oc @ Lap, # Rows _ @ o oc
Zone 2:_" oc @ Lap, # Rows _ @ _, oc
Zone 3:-" oc @ Lap, # Rows_ @ u oc
Number of Fasteners per tnsulation Board: /l/t
Zone 1':-Zone L:_Zone Z:_Zone 3:_
lllustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing
Counterflashing, Coplng, Etc.,
Indicate: Mean Roof Height, parapet Height, Height of Base
Flashing Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 1 1j. and Chapter 16..
FT.
FT.
Parapet
Height
Mean
Roof
Height
Ply Sheet Fqifener/Bonding Material:
Top Ply Fastener/Bonding Material:
ST. LUCIE
Section D (Steep Slope Roof System)
Roof System Manufacturer:
Notice of Acceptance Number:
Minimum Design Wind Pysures, lf Applicable (From RA,S 127 or Calculations):
Zone 1; L Zone 2e:------Jone 2n:-Zone 2r:-Zone 3e:-Zone 3r:
Type & Sire Drip
Edge:
)nenSiorYrA
6t^i NteS u8355-Rb
Type Underla/ment
Mean Roof'Height: I
Insulation:
FmtenerType &Spacing:
Type Cap Shet
Rmf Covsinn'
0
Ridge.
Fire Barrier:
Adhesive Type: