Loading...
HomeMy WebLinkAboutEVALUATION REPORT " MCEIVED 246-7 - E Eli/ � � U N1 ®® LI St.Lucie County COda � Permitting NEW I etc. Certificate o Authorization#32455 5-jee/353 Christian Street, Unit#13 Oxford,CT 06478 / (203)262-9245 ENGINEER EVALUATE TEST CONSULT REPORTEVALUATION RESISTO a division of Soprema,Inc. Evaluation Report 7215.06.14-R10 1640rue Haggerty FL17084-R10 RESISTO. Drummondville,QC J2C 5138 CM Y Date of Issuance:06/20/2014 (819)478-2400 Revision 10:12/16/2020 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the 71h Edition(2020)Florida Building Code sections noted herein. DESCRIPTION: RESISTO Modified Bitumen Roof Systems LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s)changes,the referenced Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change. Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any changes to the product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words "NEMO I etc. Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 4,plus a 6-page Appendix. Prepared by: �o�5°•Fa' �i Robert J.M.Nieminen,P.E. %�ti F.,; ::`r:;._ The facsimile seal appearing was authorized by Robert Nieminen,P.E. Florida Registration No.59166,Florida DCA ANE1983 ''F L�? on 12/16/2020.This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire,a financial interest in any company manufacturing or distributing products it evaluates. 2. NEMO ETC,LLC is not owned,operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen,P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither NEMO ETC,LLC nor Robert Nieminen,P.E.are,in any way,the Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained specifically for that purpose. ©2019 NEMO ETC,LLC P NEMO l etc. ROOFING SYSTEMS EVALUATION: SCOPE:1. Product Category: Roofing !, Sub-Category: Modified Bitumen Roof Systems Compliance Statement: RESISTO Modified Bitumen Roof Systems,as produced by RESISTO,a division of Soprema, Inc., have demonstrated compliance with the following sections of the 7th Edition (2020) Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/Conditions of Use set forth herein. 2. STANDARDS: Secti6ri 1504.3.1 Wind resistance FM 4474 2011 1504.6 Physical properties ASTM G15S 2013 1504.7 Impact resistance FM 4470 2016 1507.6.3 Material standard ASTM D1970 2015 1507.10.2 Material standard ASTM D4601 2012 1507.11.2 Material standard ASTM D6163 2015 1507.11.2 Material standard ASTM D6222 2011 3. REFERENCES: Entity.Mw'. r ;,, Examination Reference`; Date _ ."�._ ERD(TST6049) ASTM D6163 S35860.05.12-1-R2 03/14/2013 ERD(TST6049) ASTM D1970 S44870.04.14-1 and-4 04/10/2014 ERD(TST6049) FM 4474 S47190.06.14-2 06/20/2014 ERD(TST6049) ASTM D1970 SOPC-SC8970.15 07/22/2015 ERD(TST6049) FM 4474 SOPC-SC9315.07.15 07/22/2015 ERD(TST6049) ASTM D1970 SOPC-SC8970.08.15 08/31/2015 ERD(TST6049) ASTM D6163 S43400.08.14-5-R1 05/03/2017 FM Approvals(TST1867) FM 4470 3B1AO.AM 01/08/1998 FM Approvals(TST1867) FM 4470 797-08591-267 08/14/2013 MEMO(TST6049) ASTM D6163 4S-SOPC-18-003.11.18 01/14/2019 NEMO(TST6049) Criticality 4i-SOPC-I9-SSCRT-02.A 10/16/2019 NEMO(TST6049) FM 4474 4a-SOPC-I9-LSWUS-01.A 03/10/2020 NEMO(TST6049) ASTM D4601 4q-SOPC-20-SSMBB-01.A 03/25/2020 NEMO(TST6049) FM 4474 4a-SOPC-20-LSWUS-01.A 09/15/2020 PRI(TST5878) FM 4474 SOP-089-02-01 07/22/2016 PRI-CMT(TST5878) ASTM D6222 PRS-026-02-01 10/28/2016 PRI(TST5878) FM 4474 SOP-104-02-01 10/31/2016 PRI(TST5878) ASTM D4601 SOP-105-02-01 11/28/2016 PRI(TST5878) Criticality(TAS 117) SOP-080-02-02 12/16/2016 PRI(TST5878) FM 4474 SOP-119-02-01 04/14/2017 PRI(TST5878) FM 4474 SOP-128-02-01 08/18/2017 UL LLC (QUA9625) Quality Control Service Confirmation 05/30/2018 UL LLC (QUA9625) Quality Control Florida BCIS Current NEMO ETC,LLC Evaluation Report 7215.06.14-1130 Certificate of Authorization#32455 7-EDITION(2020)FBC NON-HVHZ EVALUATION FL17084-R10 RESISTO,a division of Soprema,Inc. Revision 10:12/16/2020 Page 2 of 4 � . NEMO etc. 4. PRODUCT DESCRIPTION: 4.1 This Evaluation Report covers RESISTO Modified Bitumen Roof Systems installed in accordance with RESISTO published installation instructions and the Limitations / Conditions ofUse herein. The following RB80 membranes make up the subject systems. ' � Ott to SA Shingle Underlayment" PrimeSource Building Products ASTM D1970 N/A N/A MS,CH,QC Base Ply "Grip-Rite Eave&Valley Protector" WATER DEFENDER" SA Smooth Ply 40 ASTM D1970 N/A N/A QC 5. LIMITATIONS: � � � � � � 5.1 This iso Building Code Evaluation. Neither NEW ETC,LLC nor Robert Nieminen,P.E.are,in any way,the Designer uf Record for any project on which this Evaluation Report,or previous versions thereof,is/was used for permitting � or design guidance unless retained xpec0:aUyforthatpurpuxe. � � 5.2 This Evaluation Report is not for use in FBC High Velocity Hurricane Zone jurisdictions (i.e., Broward and Miami- DadeCounties). 5.3 This Evaluation Report pertains tu above-deck roof components. Roof decks and structural members shall bein accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. 5.4 This Evaluation Report does not include evaluation of fire classification. Refer toFBCi505 for requirements and limitations regarding roof assembly fine classification. Refer to FBC 2603 for requirements and limitations concerning the use of foam plastic insulation. � 5.5 This Evaluation Report does not include eva|uationnf roof edge termination. Refer to FBC 1504'S for requir ements and limitations regarding edge secunement for low-slope roofs. 5.6 Refer toF0C 1511 for requirements and limitations regarding recover installations. 5.6.1 For mechanically attached components over existing roof decks,fasteners shall be tested in the existing deck for withdrawal resistance. Aqua|ified design professional shall review the data for comparison to the minimum requirements for the system. Testing shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard lASl05. 5.6.2 For bonded insulation or membrane over existing substrates in a re-roof(tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. if any surface conditions exist that bring system performance into question, field uplift testing in accordance with ANS|/SPRl]A-1,AST;NE907,FK8 Loss Prevention Data Sheet 1'52nrTesting Application Standard TASz24shall be conducted on mock-ups of the proposed new roof assembly. mcMo ETC,uz Evaluation Report nz15.ox.14-num Certificate of Authorization 1TH EDITION(zozu)Focmom'xxxzEVALUATION ru7084nxu nss/snO,"division wf,==rna,Inc. aevuvnxo:12/16/220 Page 3*v* NEMO etc. 5.6.3 For bonded insulation or membrane over existing substrates in a recover installation,the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction,as documented through field uplift testing in accordance with ASTM E907,FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124. 5.7 Refer to Appendix 1 for system attachment requirements for wind load resistance. 5.7.1 "MDP"=Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been applied).Refer to FBC 1609 for determination of design wind loads. 5.7.2 For mechanically attached components or partially-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed at least the Zone 1 PRIME design pressure determined in accordance with FBC Chapter 16. Elevated pressure zones shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29,Roofing Application Standard RAS 117 and Roofing Application Standard RAS 137. Assemblies marked with an asterisk*carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29(February 2020)for Zone 2/3 enhancements. 5.7.3 For assemblies with all components fully bonded in place,the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems. 5.8 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3. Refer to the Product Approval of the component manufacturer for components listed in Appendix 1 that are produced by a Product Manufacturer other than the report holder on Page 1 of this Evaluation Report. INSTALLATION:6. RESISTO Modified Bitumen Roof Systems shall be installed in accordance with RESISTO published installation instructions,subject to the Limitations/Conditions of Use noted herein. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Contact the named CA entity for manufacturing facilities covered by F.A.C.Rule 61G20-3 CIA requirements. Refer to Section 4 herein for products and production locations having met codified material standards. 9. QUALITY ASSURANCE ENTITY: UL LLC—QUA9625;(414)248-6409,karen.buchmannC)ul.com -THE SIX(6)PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT- MEMO ETC,LLC Evaluation Report 7215.06.14-R10 Certificate of Authorization#32455 7-EDITION(2020)FBC NON-HVHZ EVALUATION FL17084-R10 RESISTO,a division of Soprema,Inc. Revision 10:12/16/2020 Page 4 of 4 z ' O-NEMOjetc. APPENDIX 1:ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE TABLE DECK APPLICATION TYPE DESCRIPTION PAGE 1A Wood New or Reroof(Tear-Off) A-1 Bonded Insulation,Bonded Roof Cover 2 1B Wood New or Reroof(Tear-Off) A-2 Mech.Attached Anchor Sheet,Bonded Insulation,Bonded Roof Cover 3 1C Wood New,Reroof(Tear-Off)or Recover C-1 Mechanically Attached Insulation,Bonded Roof Cover 3 1D Wood New,Reroof(Tear-Off)or Recover D-2 Insulated,Mech.Attached Base Sheet,Bonded Roof Cover 4 1E Wood New or Reroof(Tear-Off) E-2 Non-Insulated,Mech.Attached Base Sheet(nails),Bonded Roof Cover 4-5 1F Wood New,Reroof(Tear-Off)or Recover E-2 Non-Insulated,Mech.Attached Base Sheet(screws&plates),Bonded Roof Cover 6 1G Wood New or Reroof(Tear-Off) F Non-Insulated,Bonded Roof Cover 6 The following notes apply to the systems outlined herein: .. ��p 1 The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC regV��net h ' f wb o&L/h lui�99dy klaving Jurisdiction. RTa LUCIE Ow"UNW 2 Fasteners shall be of sufficient length for the following engagements: [� �f ➢ Wood Deck: Min.0.75-inch plywood penetration or minimum 1-inch wood plank embedment. 3 Unless otherwise noted,insulation may be any one layer or combination of FBC Approved(Local or Statewide)board(s)that meet FBC 1505 and,for foam plastic,FBC Chapter 26,when installed with the roof cover. 4 Minimum 200 psi,minimum 2-inch thick FBC Approved lightweight insulating concrete may be substituted for rigid insulation board for System Types B-1,C-1,C-2,D-1 or D-2,whereby fasteners are installed through the lightweight insulating concrete to engage the structural deck. The structural deck shall be of equal or greater type,thickness and strength to the steel and structural concrete deck listings. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. This is a wind uplift resistance allowance and does not purport to address non- wind-uplift-related issues,such as deck venting or moisture levels within the LWIC and the potential effect on overlying components. 5 Preliminary insulation attachment for System Type D:Unless otherwise noted,refer to Section 2.2.10.1.3 of FM Loss Prevention Data Sheet 1-29(February 2020). 6 Unless otherwise noted,insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application;the ribbons/beads shall expand as noted in he anu asturer's published instructions. �gt ➢ RESISTOBOND: Continuous 0.5 to 0.75-inch wide ribbons,max.12-inch o.c. Li ➢ DuPont INSTA STIK Quik Set Insulation Adhesive(INSTA STIK): Continuous 0.75 to 1-inch wide ribbons,max.12-inch o.c. ➢ OMG OlyBond 500: Continuous 0.75 to i-inch wide ribbons,max.12-inch o.c. ➢ Note:When multiple layers(s)of insulation and/or coverboard are installed in ribbon-applied adhesive,board joints shall be staggered. ➢ Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing. 7 Unless otherwise noted,all insulations are flat-stock or taper board of the minimum thickness noted. 8 For adhered roof insulation and board-size: Unless otherwise noted,refer to Section 2.2.10.6.2 of FM Loss Prevention Data Sheet 1-29(February 2020). 9 For mechanically attached components or partially-bonded insulation,the maximum design pressure for the selected assembly shall meet or exceed at least the Zone 1 PRIME design pressure determined in accordance with FBC Chapter 16. Elevated pressure zones shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1,FM Loss Prevention Data Sheet 1-29,Roofing Application Standard RAS 117 and Roofing Application Standard RA5137. Assemblies marked with an asterisk'carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29(February 2020)for Zone 2/3 enhancements. L For assemblies with all components fully bonded,the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems. O ETC,LLC Evaluation Report 7215.06.14-R9 for FL17084-R9 icate ofAuthorization#32455 7TM EDITION(2020)FBC NON-HVHZ EVALUATION Revision 9:09/18/2020 9 NEMO ETC,LLC RESISTO,a division of Soprema,Inc.;(819)478-2400 Appendix 1,Page 1 of 6 ONEMOletc. 11 For mechanically attached components over existing decks,fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard TAS 105. 12 For bonded insulation or membrane over existing substrates in a re-roof(tear off)or recover installation,the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question,field uplift testing in accordance shall be conducted on mock-ups of the proposed new roof assembly. For bonded insulation or membrane over existing substrates in a recover installation,the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction,as documented through field uplift testing. Field uplift testing shall be in accordance with ASTM E907,FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124. 13 Refer to FBC 1511 for requirements and limitations regarding recover installations. For Structural Concrete Deck or Recover Applications using System Type C-1,C-2,D-1 or D-2,the insulation is optional. Alternatively,an FBC Approved insulation board or coverboard may be used as a separation layer. Board products shall be preliminarily attached prior to roof cover installation(Note 5 herein). The separator component shall be documented as meeting FBC 15.05 and,for foam plastic,FBC Chapter 26,when installed with the roof cover in Recover applications. 14 Lightweight insulating concrete(LWIC)shall be cast in accordance with FBC Section 1917 to the satisfaction of the Authority Having Jurisdiction. For systems where specific LWIC is referenced,refer to current LWIC Product Approval for specific deck construction and limitations. Unless otherwise noted,for systems where specific LWIC is not referenced,the minimum design mix shall be 300 psi. In all cases,the minimum top-coat thickness is 2-inches. For LWIC over structural concrete,reference is made to FBC Section 1917.4.1,Point 1. For"pre-existent'LWIC references,listings were established through testing over lightweight concrete cast using only foaming agent(ASTM C896),water and Portland cement(ASTM C150),with no proprietary additives,in accordance with procedures adopted by Miami-Dade BCCO(FBC CER1592). Use of these listings in new construction or re-roof(tear-off)applications is at the discretion of the Designer or Record and Authority Having Jurisdiction. 15 For bonded membrane applications,refer to the tables herein. The following are acceptable alternates to the listed membranes. ACCEPTABLE ALTERNATES RESISTO Product Alternate Beacon Roofing"TRI-BUILT Sand-R SA Shingle Underlayment" RESISTO LB1236 PrimeSource Building Products"Grip-Rite Eave&Valley Protector" SRS Distribution'TopShield ICE&WATER DEFENDER" 16 A slip-sheet of Modified Sopra-G or other approved ASTM D4601,Type II fiberglass base sheet may be loose laid atop the wood deck prior to the installation of overlying mechanically fastened components with no adverse effect on system performance. 17 "MDP"=Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads.Refer to FBC 1609 for determination of design wind loads TABLE IA: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF) SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER System Deck Base Insulation Layer Top Insulation Layer(s) Roof Cover(Note 1S) MOP Attach Attach Primer No. (Note i) Type Type Base Ply Ply Cap Ply (pSf) (Notes 6,7,8) (Notes 6,7,8) APA rated,7/16 CAT,0.418 in., Min.1.5-inch RESISTOBOND, (Optional) RESISTOBOND, (Optional) RESISTO (Optional) RESISTO BITUTAK MB W 1 Exposure 1 OSB,min.15/32" ACFoam II,SOPRA- INSTA STIK or Additional INSTA STIK or RESISTO RESISTO BITUTAK. SMOOTH or RESISTO APA rated plywood or nominal ISO s,H-Shield or OlyBond 500, layers(s)base OlyBond 500, EXTERIOR LB1236,self- MB SMOOTH, BITUTAK MB MINERAL, -52.5 1"T&G wood plank SOPRA-ISO r 12"o.c. insulation 12"o.c. PRIMER adhering torch-applied torch-applied APA rated,7/16 CAT,0.418 in., Min.1.5-inch RESISTOBOND, (Optional) RESISTOBOND, (Optional) RESISTO (Optional) RESISTO BITUTAK MB W 2 Exposure 1 OSB,min.15/32" ACFoam II,SOPRA- INSTA STIK or Additional INSTA STIK or RESISTO RESISTO BITUTAK SMOOTH or RESISTO APA rated plywood or nominal ISO s,H-Shield or OlyBond 500, layers(s)base OlyBond 500,6" EXTERIOR LB1236,self- MB SMOOTH, BITUTAK MB MINERAL, -105.0 1"T&G wood plank SOPRA-ISO r 6"o.c. insulation O.C. PRIMER adhering torch-applied torch-applied NEMO ETC,LLC Evaluation Report 7215.06.14-R9 for FL17084-119 Certificate of Authorization#32455 7T"EDITION(2020)FBC NON-HVHZ EVALUATION Revision 9:09/18/2020 ©2019 NEMO ETC,LLC RESISTO,a division of Soprema,Inc.;(819)478-2400 Appendix 1,Page 2 of 6 i -' NEnno�etc. TABLE 1B: ... . CONSTRUCTION (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF Anchor Sheet Base Insulation Layer(s) Top Insulation Layer _ Roof Cover(Note 15) System Deck _ MDP Fasteners Attach Attach Primer No. (Note i . Type (Note 11) Attach Type (Notes 6,7,B) Type (Notes 6;7,8) Base Ply Ply Cap Ply' (psf) APA rated,7/16 32 ga.,1-5/8- 8-inch o.c.at 4- (Optional) RESISTO CAT,0.418 in., inch wide side Min.1.5-Inch (Optional) BITUTAK MB inch diameter RESISTOBOND, RESISTOBOND, (Optional) RESISTO RESISTO Exposure 1 OSB, laps and 8-Inch ACFoam 11, Additional SMOOTH or tin caps with INSTA STIK or INSTA STIK or RESISTO LBi236, BITUTAK MB W-3. min.15/32"APA SA Nail Base 12 ga. OlyBond 500, OlyBond 500, EXTERIOR self- SMOOTH o.c.at three(3) SOPRA-ISO s, layers(s) RESISTO -30.0* , rated plywood equally spaced H-Shield or base BITUTAK MB or nominal 1" annular ring rows in the center SOPRA-ISO r 12"o.c. insulation 12"o.c. PRIMER adhering torch- MINERAL, T&G wood plank shank nails of the sheet applied torch-applied APA rated,7/16 32 ga.,1-5/8- 6-inch o.c.at 4- (Optional) RESISTO CAT,0.418 in., inch diameter inch wide side Min.1.5-Inch (Optional) BITUTAK MB (Optional) RESISTO RESISTO Exposure 1 OSB, tin caps with INSTA STIK,12" INSTA STIK,12"laps and 6-inch ACFoam 11, Additional RESISTO LB1236, BITUTAK MB SMOOTH or W-4. min.15/32"APA RESISTOFLEX annular ring o.c.at three(3) SOPRA-ISO s, layers(s) PRIMER adhering torch- RESISTO -37.5* 12 ga. O.C. O.C. EXTERIOR self- SMOOTH, rated plywood equally spaced H-Shield or base BITUTAK MB or nominal 1" shank nails rows in the center SOPRA-ISO r insulation MINERAL, applied T&G wood plank of the sheet PP torch-applied APA rated,7/16 32 ga.,1-5/8- 6-inch o.c.at 4- (Optional) RESISTO CAT,0.418 in., inch diameter inch wide side Min.1.5-inch (Optional) BITUTAK MB (Optional) RESISTO RESISTO Exposure 1 OSB, laps and 6-inch ACFoam 11, Additional SMOOTH or tin caps with INSTA STIK,6" INSTA STIK,6" RESISTO LBi236, BITUTAK MB W-5. min.15/32"APA RESISTOFLEX o.c.at four(4) SOPRA-ISO s, layers(s) RESISTO -75.0 12 ga. O.C. O.C. EXTERIOR self- SMOOTH, rated plywood equally spaced H-Shield or base BITUTAK MB annular ring PRIMER adhering torch- or nominal 1" rows in the center SOPRA-ISO r insulation MINERAL, shank nails T&G wood plank of the sheet applied torch-applied TABLE 1C: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER Top Insulation Layer- Roof Cover(Note 15) System Deck Base Insulation Primer MDP No. (Note i) (Note 13) Type Fasteners Attach Base Ply Ply Cap Ply (Psfl . (Note 11) Min.15/32-inch Soprema#12 DP (Optional) (Optional)One or more Min.1.5-inch ACFoam II, APA rated Fasteners with 1 per 1.6 RESISTO SA Smooth Ply SA Cap GR or SA Cap FR W 6 None plywood at max. layers,any SOPRA-ISO s,H-Shield, Soprema 3"Metal ft, EXTERIOR 40 GR 67.5 24-inch spans combination,loose laid SOPRA-ISO r Insulation Plates PRIMER Min.15/32-inch (Optional)One or more Min.1.5-inch ACFoam II, Soprema#12 DP (Optional) RESISTO (Optional) RESISTO BITUTAK MB APA rated Fasteners with 1 per 1.6 RESISTO RESISTO BITUTAK SMOOTH or RESISTO W-7. layers,any SOPRA-ISO s,H-Shield, a L81236,self- -67.5 plywood at max. combination,loose laid SOPRA-ISO r Soprema 3"Metal ft EXTERIOR adhering MB SMOOTH, BITUTAK MB MINERAL, 24-inch spans Insulation Plates PRIMER torch-applied torch-applied NEMO ETC,LLC Evaluation Report 7215.06.14-119 for F1.17084-119 Certificate of Authorization✓K32455 7-EDITION(2020)FBC NON-HVHZ EVALUATION Revision 9:09/18/2020 ©2019 NEMO ETC,LLC RESISTO,a division of Soprema,Inc.;(819)478-2400 Appendix 1,Page 3 of 6 ONEMOjetc. TABLE ID: DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER BONDEDSYSTEMTYPED-2: INSULATED,MECHANICALLY ATTACHED BASE SHEET, ROOF System Base Sheet Roof Cover 1S) Y Insulation Layer(s) MDP No. Deck Note i ( ) (Note 13) Type Fasteners Attach Base Ply Ply Cap Ply (Pso (Note 11) APA rated,7/16 CAT,0.418 (Optional) RESISTO BITUTAK MB One or more layers,min. Trufast#12 DP with 8-inch o.c.at the 4-inch laps in.,Exposure 1 OSB,min. SA Nail RESISTO LB1236, RESISTO BITUTAK SMOOTH or RESISTO 82.5 W 8 1-inch,any combination Trufast 3"Metal and 8-inch o.c.at three(3), 15/32"APA rated plywood or , , Base self-adhering MB SMOOTH, BITUTAK MB MINERAL, nominal 1"T&G wood plank loose-laid Insulation Plates equally spaced center rows torch-applied torch-applied APA rated,7/16 CAT,0.418 (Optional) (Optional) RESISTO BITUTAK MB One or more layers,min. Trufast#12 DP with 8-inch o.c.at the 4-inch laps in.,Exposure 1058,min. MODIFIED RESISTO BITUTAK RESISTO BITUTAK SMOOTH or RESISTO W 9 15/32"APA rated plywood or loose-lnch,aid any combination, SOPRA-G Trufast 3"Metal and flinch spaced at three rows MB SMOOTH, MB SMOOTH, BITUTAK MB MINERAL, -120.0 nominal 1"T&G wood lank loose-laid Insulation Plates equally spaced center rows P torch-applied torch-applied torch-applied TABLE IE: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(NAILs),BONDED ROOF COVER Base Sheet Roof Cover(Note 1S) System Note i MDP Deck No. ( ) Base Fasteners Attach Primer Base Ply Primer Ply Cap Ply (Psf) (Note 13) 1. 32 ga., 8-inch o.c.at 4-inch wide g (Optional) APA rated,7/16 CAT, SA Nail diameter tin caps with RESISTO BITUTAK side laps and 8-inch o.c.at RESISTO RESISTO BITUTAK MB W-10. 0.418 in.,Exposure i three(3)equally spaced None LB1236,self- None SMOOTH or RESISTO BITUTAK -30.0* shank nails torch applied OSB Base 12 ga.annular ring rows in the center of the adhering NIB SMOOTH, MB MINERAL,torch-applied sheet Min.7/16-inch OSB or SOPRA-G 32 ga.,1-5/8-inch 6-inch o.c.at the 4-inch RESISTO RESISTO W-11. min.15/32-inch APA or diameter tin caps with laps and 6-inch o.c.at four EXTERIOR SA Base EXTERIOR None SA Cap GR or SA Cap FR GR -37.5* rated plywood MODIFIED 11 ga.annular ring (4),equally spaced, PRIMER PRIMER SOPRA-G shank nails staggered center rows 32 ga.,1-5/8-inch 7-inch o.c.at the 4-inch RESISTO RESISTO Min.19/32-inch APA diameter tin caps with laps and 7-inch o.c.at W 12. rated plywood SOPRA-G 11 ga.annular ring three(3),equally spaced, EXTERIOR SA Base EXTERIOR None SA Cap GR or SA Cap FR GR 37.5 shank nails staggered center rows PRIMER PRIMER 32 ga.,1-5/8-inch 8-inch o.c.at the 4-inch W-13. Min.15/32-inch APA SA Nail diameter tin caps with laps and 8-inch o.c.at (Optional)SA rated plywood Base 11 ga.annular ring three(3),equally spaced, None Smooth Ply 40 None None SA Cap GR or 5A Cap FR GR 45.0 shank nails staggered center rows 32 ga.,1-5/8-inch 8-inch o.c.at the 4-inch RESISTO (Optional)W-14. Min.15/32-inch APA SA Nail diameter tin caps with laps and 8-inch o.c.at RESISTO BITUTAK RESISTO BITUTAK MB rated plywood Base 11 ga.annular ring three(3),equally spaced, None LB1236,self- None MB SMOOTH, SMOOTH or RESISTO BITUTAK -45.0 shank nails staggered center rows adhering torch-applied MB MINERAL,torch-applied NEMO ETC,LLC Evaluation Report 7215.06.14-119 for F1.37084-119 Certificate of Authorization#32455 7-EDITION(2020)FBC NON-HVHZ EVALUATION Revision 9:09/18/2020 ©2019 NEMO ETC,LLC RESISTO,a division of Soprema,Inc.;(819)478-2400 Appendix 1,Page 4 of 6 ONEMOjetc- TABLE ... . CONSTRUCTION.. . ... . . BONDEDSYSTEM TYPE E-2: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(NAILS), ROOF COVER Base Sheet Roof Cover(Note 15) System MDP Deck(Note 1) Fasteners Primer No. Base Attach Base Ply Primer -Ply .Cap Ply (Ps) (Note 11) 32 ga.,1-5/8-inch 6-inch o.c.at the 4-inch Min.15/32-inch OSB RESISTO RESISTO W-15. or min.15/32-inch SOPRA-G diameter tin caps with laps and 5-inch o.c.at four EXTERIOR SA Base EXTERIOR None SA Cap GR or SA Cap FR GR -45.0 APA rated I 11 ga.annular ring (4),equally spaced, plywood PRIMER PRIMER shank nails staggered center rows 32 ga.,1-5/8-inch 6-inch o.c.at the 4-inch (Optional) RESISTO RESISTO BITUTAK MB Min.15/32-inch APA SA Nail diameter tin caps with laps and 6-inch o.c.at four None RESISTO BITUTAK SMOOTH or 5T0 W-16. rated plywood Base 12 ga.annular ring (4),equally spaced, adheri,self- None MB SMOOTH, RE BITUTAK 52.5 shank nails staggered center rows adhering torch-applied MB MINERAL,torch-applied Min.19/32-inch APA 32 ga.,1-5/8-inch 8-inch o.c.at the 4-inch rated plywood or SA Nail diameter tin caps with laps and 8-inch o.c.at (Optional)SA W-17. nominal i"T&G wood Base 11 ga.annular ring three(3),equally spaced None Smooth Ply 40 None None SA Cap GR or SA Cap FR GR -60.0 plank shank nails center rows Min.19/32-inch APA 32 ga.,1-5/8-inch 8-inch o.c.at the 4-inch (Optional) RESISTO RESISTO BITUTAK MB rated plywood or SA Nail diameter tin caps with laps and 8-inch o.c.at RESISTO BITUTAK W-18. nominal 1"T&G wood Base 11 ga.annular ring three(3),equally spaced None LBie self- None MB SMOOTH, SMOOTH or RE BITUTAK 60.0 adherin plank shank nails center rows ring torch-applied MB MINERAL,torch-applied rch-applied APA rated,7/16 CAT, GAP (Optional) 6-inch o.c.at the 3-inch (Optional) 0.418 in.,Exposure 1 Organic RESISTO RESISTO BITUTAK MB Simplex MAXX Cap laps and 6-inch o.c.at RESISTO BITUTAK W-19. OSB or min.15/32- Base None BITUTAK MB None SMOOTH or RESISTO BITUTAK -60.0 inch APA rated Sheet Fastener three(3),equally spaced SMOOTH, MB SMOOTH, MB MINERAL,torch-applied plywood (##43) center rows torch-applied torch-applied Min.19/32-inch APA 32 ga.,1-5/8-inch 6-inch o.c.at the 4-inch rated plywood or SA Nail diameter tin caps with laps and 6-inch o.c.at (Optional)SA W 20. nominal 1"T&G wood Base 0.120"x 1.25"ring three(3),equally spaced None Smooth Ply 40 None None SA Cap GR or SA Cap FR GR 90.0 plank shank roofing nails center rows Min.19/32-inch APA 32 ga.,1-5/8-inch 6-inch o.c.at the 4-inch (Optional) RESISTO RESISTO BITUTAK MB rated plywood or SA Nail diameter tin caps with laps and 6-inch o.c.at RESISTO BITUTAK W-21. nominal 1"T&G wood Base 0.120"x 1.25"ring three(3),equally spaced None a ,self- None MB SMOOTH, SMOOTH or RE BITUTAK 90.0 dheri plank shank roofing nails center rows adhering torch-applied MB MINERAL,torch-applied rch-applied Min.19/32-inch APA 32 ga.,1-5/8-inch 4-inch o.c.at the 4-inch rated plywood or SA Nail diameter tin caps with laps and 4-inch o.c.at four (Optional)SA W 22. nominal 1"T&G wood Base 0.120"x 1.25"ring (3),equally spaced center None Smooth Ply 40 None None SA Cap GR or SA Cap FR GR -105.0 plank shank roofing nails rows Min.19/32-inch APA 32 ga.,1-5/8-inch 4-inch o.c.at the 4-inch (Optional) I RESISTO RESISTO BITUTAK MB rated plywood or SA Nail diameter tin caps with laps and 4-inch o.c.at four W 23. nominal 1"T&G wood Base 0.120"x 1.25"ring (3),equally spaced center None LBie self- None MB SMOOTH RESISTO BITUTAK SMOOTH or RESISTO BITUTAK -105.0 plank shank roofing nails rows adhering torch-applied MB MINERAL,torch-applied NEMO ETC,LLC Evaluation Report 7215.06.14-119 for F1.17084-119 Certificate of Authorization##32455 7-EDITION(2020)FBC NON-HVHZ EVALUATION Revision 9:09/18/2020 ©2019 NEMO ETC,LLC RESISTO,a division of Soprema,Inc.;(819)478-2400 Appendix 1,Page 5 of 6 (0, NEMO etc. TABLE IF: WOOD . REROOF(TEAR-OFF)OR RECOVER SYSTEM TYPE E-2: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(SCREWS&PLATES),BONDED ROOF COVER Base Sheet Roof Cover(Note,15) System. Deck(Note 1) MDP (Note IS) No. Base Fasteners Attach Primer Base Ply Primer Ply Cap Ply (psf) _ Min.19/32-inch APA rated plywood or SA Nail Trufast#12 DP with 8-inch o.c.at the 4-inch laps p y W-24• Trufast 3"Metal and 8-inch o.c.at three(3), None (Optional)SA None None SA Cap GR or SA Cap FR GR -127.5 nominal 1"T&G wood Base Insulation Plates equally spaced center rows Smooth Ply 40 plank Min.19/32-inch APA Trufast#12 DP with (Optional) rated I 8-inch o.c.at the 4-inch laps RESISTO RESISTO BITUTAK MB W 25 P or Nail Trufast 3"Metal and 8-inch o.c.at three(3), None LB1236,self- None RESISTO BITUTAK SMOOTH or RESISTO BITUTAK -127.5 nominall 1 1""T&T&G wood Base Insulation Plates equally spaced center rows adhering MB SMOOTH, MB MINERAL,torch-applied plank torch-applied TABLE 1G: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF) SYSTEM TYPE F:NON-INSULATED,BONDED ROOF COVER System Roof Cover(Note 15) No. Deck(Notes i&12) Primer - � MDP(psf) Base Ply Primer Ply Cap Ply W 26 Min.7/16-inch APA rated OSB or min. RESISTO EXTERIOR SA Base RESISTO EXTERIOR None SA Cap GR or SA Cap FR GR 45.0 15/32-inch APA rated plywood PRIMER PRIMER W-27. Min.15/32-inch APA rated OSB None SA Smooth Ply 40 None None SA Cap GR or SA Cap FR GR -67.5 W-28. Min.15/32-inch APA rated OSB RESISTO EXTERIOR SA Smooth Ply 40 None None SA Cap GR or SA Cap FR GR -75.0 PRIMER W 29 APA rated,7/16 CAT,0.418 in.,Exposure (Optional)RESISTO RESISTO LB1236, None (Optional)RESISTO BITUTAK RESISTO BITUTAK MB SMOOTH or RESISTO 1 OSB,min.15/32"APA rated plywood EXTERIOR PRIMER self-adhering MB SMOOTH,torch-applied BITUTAK MB MINERAL,torch-applied 97.5 W-30. Min.15/32-inch APA rated plywood None SA Smooth Ply 40 None None SA Cap GR or SA Cap FR GR -105.0 W-31. Min.15 32-inch APA rated I RESISTO EXTERIOR / plywood PRIMER SA Smooth Ply 40 None None SA Cap GR or SA Cap FR GR 112.5 W-32. Nominal 1"T&G wood plank (Optional)RESISTO RESISTO LB1236, None (Optional)RESISTO BITUTAK RESISTO BITUTAK MB SMOOTH or RESISTO -135.0 EXTERIOR PRIMER self-adhering MB SMOOTH,torch-applied BITUTAK MB MINERAL,torch-applied NEMO ETC,LLC Evaluation Report 7215.06.14-R9 for FL17084-119 Certificate ofAuthorization#32455 7-EDITION(2020)FBC NON-HVHZ EVALUATION Revision 9:09/18/2020 ©2019 NEMO ETC,LLC RESISTO,a division of Soprema,Inc.;(819)478-2400 Appendix 1,Page 6 of 6