HomeMy WebLinkAboutAPPROVED, 37022-ROOFING INFO SHEETSST. L
Mas
Con
Job,
❑1
Low
Sket
dimf
.UCIE WORKS
Section A (General Information
ter Permit No.
Process No.
CM 330489
tractors Name: Total Home Roofing License #
address v v )3 At 0 -
ROOF CATEGORY
tlope 0 Mechanically Fastened Tile
ltic Shingles ❑ Metal Panel/Shingles
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE_
dew roof ❑ Repair ❑ Maintenance 114 Rroofing
ROOF SYSTEM INFORMATION }
Slope Roof Area (SF) � Steep Sloped Roof Area (SF) d`
Section B (Roof Plan)
-h Roof Plan: Illustrate all levels and sections, roof drains, scuppers, over
�nsions of sections and levels, clearly identify dimensions of elevated pressui
❑ Mortar/Adhesive Set Tiles
❑Wood Shingles/Shakes
❑ Recovering
r
Total (SF) '2
ow scuppers and overflow drains. I
a zones and location of parapets.
I!
E
L;
LF.
/-N
I
]A%..
o, IF
—1
D_
t
I
s
}
l
r
I
i
N�
iclude
ST. LUCIE WORKS
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component is not used, identify as "NA")
System Manufacturer: Certalnteed
Product Approval Ni Fl_2533-R24
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1': -34.6 Zone 1 60.3Zone 2: Zone 3 -t 08.4
Max. Design Pressure, from the specific product approval
system: -127.5
Deck:
Type: Wood
Gauge Thickness: 1 /8"
Slope:
Anchor/Base Sheet & No. df Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s): Fllntingfir
Base Sheet Fastener/Bonding Material:
Ply Sheet(s)' & No. of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply: Flintlagtir.
Top Ply Fastener/Bonding Material:
SA
Surfacing:
Fastener Spi
Jng for Anchor/Base Sheet Attachment:
Zone 1':
'cc @ Lap, # Rows_
®— cc
Zone I:—
oc@Lap, # Rows
—0—cc
Zone 2:_.,_.
oc @ Lap, # Rows
— ®_ oc
Zone 1-1
oc @ Lap, # Rows_
® ° oc
Number of F steners Per Insulation Board:
Zone 1': Zone 1:—Zone 2:_Zone 3
Illustrate Co ponents Noted and Details as Applicable:
Woodblockii g, Gutter, Edge Termination, Stripping,
Flashing, Cc ntinuous Cleat, Cant Strip, Base Flashing,
Counterflas ng, Coping, Etc...
Indicate: Men Roof Height, Parapet Height, Height of Base
Flashing, Coy ponent Material, Material' Thickness, Fastener
Type, Fasten r Spacing orSubmit Manufacturers Details that
Comply with AS 111 and Chapter 16.,
Fli
FT.
Parapet
Height
FT.
15'
Mean
Roof
Drip Edge: 3 X 3" Galy Alum Height
ST. LUCIE WORKS
Section D (Steep Slope Roof System)
Roof System Manufacturer: Owens Cornl
Notice of Acceptance Number:
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1:-pone 2e: -74one 2n:108 one 2r: 10�one
R f Slope:
12
r
Deck Type: I Wood
Type Underlayment
Mean Roof Height: 15'
Insulation: I N/A
Fire Barrier:
Fastener Type & Spacing:
Adhesive Type: I ' �,
Type Cap Sheet
Roof Coverint
Tvoe&S
3r:-128
Asphalt Shingles
e Drip 3" X 3" Galy Alum