Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAboutOwens Corning Shingle_FL10674-R16NEMO I etc.
Certificate of Authorization #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203) 262-9245
ENGINEER EVALUATE TEST CONSULT
EVALUATION•
Owens Corning Evaluation Report 037940.02.12-R11
One Owens Corning Parkway FL10674-1116
Toledo, OH 43659 Date of Issuance: 02/06/2012
(740) 404-7829 Revision 11: 12/11/2020
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for
compliance with the 7" Edition (2020) Florida Building Code sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1 / R905.2.6.1
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change.
Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any
changes to the product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a
complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words "NEMO Ietc. Evaluated" may be
displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its
entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 10.
Prepared by:
Robert J.M. Nieminen, P.E. ��^ ? The facsimile seal appearing was authorized by Robert
•, c' Nieminen, P.E. on 12/11/2020. This does not serve as an
Florida Registration No. 59166, Florida DCA ANE1983 'd %.; ',;' . ''` electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEW ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
S. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
©2018 NEMO ETC, LLC
ONEMOletc.
ROOFING SYSTEMS EVALUATION:
Product Category: Roofing
Sub -Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have
demonstrated compliance with the following sections of the 71" Edition (2020) Florida Building Code through
testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and
Limitations / Conditions of Use set forth herein.
Section
Property
Standard
Year
1507.2.4, R905.2.3
Physical Properties
ASTM D1970
2015
1507.2.5, R905.2.4
Material standard
ASTM D3462
2010
1507.2.7.1, R905.2.6.1
Wind Resistance
ASTM D3161
2016
1507.2.7.1, R905.2.6.1
Wind Resistance
ASTM D7158
2019
Entity
Examination
Reference
Date
Owens Corning
Declaration
Equivalency Declaration
08/06/2019
PRI(TST5878)
ASTM D1970
OCF-382-02-01
10/24/2017
UL LLC (CER9626)
Physicals & Wind Resistance
File R2453, Vol. 3
02/15/2007
UL LLC (CER9626)
Physicals & Wind Resistance
20120516-R2453
05/16/2012
UL LLC (TST9628)
Physical Properties
06CA20263
04/18/2006
UL LLC (TST9628)
Wind Resistance
11CA34308
02/18/2012
UL LLC (TST9628)
Physicals & Wind Resistance
4786093137
02/01/2014
UL LLC (TST9628)
Wind Resistance
4786126532
02/10/2014
UL LLC (TST9628)
Physical Properties
Classification letter
02/13/2014
UL LLC (TST9628)
Physical Properties
Classification letter
10/02/2015
PRI (QUA9110)
Quality Control
Service Confirmation
04/05/2020
PRI (QUA9110)
Quality Control
Florida BCIS
Current
TABLE 1: ASPHALT SHINGLE COMPONENTS
Type
Product
Plant(s)
Material
Description
Standard
Starter Strip Shingle
H-TX, OR
Starter Strip Plus
MN, OR
Accessory
ASTM D3462
starter strips for asphalt roof shingles
Starter
SRS TopShield Starter
MN, OR
Strips
Starter Shingle Roll
NH
ASTM D1970
mineral -surfaced, fiberglass -reinforced,
self -adhering SBS modified bitumen starter
Supreme®
GA, CA, CO, I -TX, NJ, OH,
ASTM D3462
fiberglass reinforced 3-tab asphalt
TN, OR, IL
roof shingles
Berkshire®
MN
ASTM D3462
fiberglass reinforced, 4-tab asphalt
roof shingles
Duration® Premium
CA, OR
Duration® Premium COOL
CA
Asphalt
TruDefinition® Duration®
Shingles
IN, CA, CO, I -TX, FL, NJ, OH,
TruDefinition® Duration
Designer Color Collection
MN, OR, GA, IL, TN
ASTM D3462
fiberglass reinforced, laminated
asphalt roof shingles
Oakridge®
GA, IN, CA, CO, H-TX, I -TX,
FL, NJ OH, TN
TruDefinition® Oakridge°
H-TX, I -TX
WeatherGuard® HP
TN
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 2 of 10
ONEMO I etc.
TABLE 1: ASPHALT SHINGLE COMPONENTS
Type
Product
Plant(s)
Material
Description
Standard
Berkshire' Hip and Ridge
Shingles with Sealant
MN
DuraRidge® Hip and Ridge
MN
Hip and
fiberglass reinforced, hip and ridge
Ridge
Shingles with Sealant
ASTM D3462
asphalt roof shingles
ProEdge®
GA, CA, OH, OR
Shingles
WeatherGuard® HP Hip and
Ridge Shingles
TN
5.1 This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer
of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting
or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC High Velocity Hurricane Zone jurisdictions (i.e., Broward and Miami -
Dade Counties).
5.3 This Evaluation Report pertains to above -deck roof components. Roof decks and structural members shall be in
accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction.
5.4 This Evaluation Report does not include evaluation of fire classification. Refer to FBC 1505 for requirements and
limitations regarding roof assembly fire classification. Refer to FBC 2603 for requirements and limitations
concerning the use of foam plastic insulation.
5_5 Wind Classification: Refer to Section 6 for installation requirements to meet wind classifications
TABLE 2A: WIND CLASSIFICATIONS, ASPHALT SHINGLES
Product
FBC Table 1507.2.7.1 or R905.2.6.1
Supreme®
ASTM D3161(F) & ASTM D7158(H)
Berkshire®
Duration® Premium
Duration® Premium COOL
TruDefinition® Duration®
TruDefinition® Duration® Designer Color Collection
Oakridge®
TruDefinition® Oakridge®
WeatherGuard® HP
5.5.1 Classification by ASTM D7158:
ASTM D7158, Class H applies only to exposure category B or C and a building height of 60 feet or less. Calculations
by a qualified design professional are required for conditions outside these limitations. Contact the shingle
manufacturer for data specific to each shingle.
NEMO ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 3 of 10
NNEMO I etc.
TABLE 2B: WIND CLASSIFICATIONS, STARTER STRIPS AND HIP & RIDGE
Type
Product
FBC Table 1507.2.7.1 or R905.2.6.1
Starter Strips
Starter Strip Shingle
ASTM D3161, Class F
Starter Strip Plus
SRS TopShield Starter
Hip & Ridge
Shingles
Berkshire® Hip and Ridge Shingles with Sealant
ASTM D3161, Class F
DuraRidge® Hip and Ridge Shingles with Sealant
ProEdge°
WeatherGuard® HP Hip and Ridge Shingles
5.5.2 Refer to Owens Corning published information on wind resistance and installation limitations.
5.6 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 614320-3.
Refer to the Product Approval of the component manufacturer for components that are produced by a Product
Manufacturer other than the report holder on Page 1 of this Evaluation Report.
6.1.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle
manufacturer's minimum requirements.
6.1.2 Underlayment shall be acceptable to the shingle manufacturer and shall hold current Florida Statewide Product
Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3.
6.1.3 Fasteners shall be in accordance with the shingle manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.1.4 Owens Corning asphalt shingles are acceptable for use in reroof (tear -off) or recover applications, subject to the
limitations set forth in FBC Section 1511 or R908 and published installation instructions.
6.2 ACCESSORY STARTERS:
6.2.1 Installation of Starter Strip Shingle, Starter Strip Plus and SRS TopShield Starter shall comply with the Owens
Corning current published instructions, using minimum five (5) nails per strip.
Felt underlayment
Deck
SeH-adhered
WeatherLoW
un derl ayment
Drip
Drip edge
edge
- Nailslocated
2'-X' from eave
Installfirst
SeH-sealing adhesive
Starter Strip
positioned along eave
shingle with
6" removed
Starter Strip shingle overhangs eaves and rakes '/;'-W'
Felt u n do da ym tot
Deck SaNdharad
WeatherLockO
1
undnlaymarrt
Drip edge
Drip —
Nails located
- 7"-3" frarn eeve
�rna�frst Stoner Strip Plus
Seisealing adh esive
posaianed along save
with 6" removed
StarW Stdp Plus nvarhangs raves and rakes 1 iC-314
Figure 1: Minimum Nailing, Starter Strip Figure 2: Minimum Nailing, Starter Strip Plus
NEMO ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 4 of 10
NNEMOjetc.
6.2.2 Installation of Starter Shingle Roll shall comply with the Owens Corning current published instructions.
Drip edge
Deck
Underlayment
Self-sealing adhesive
positioned along eaves
Figure 3: Starter Shingle Roll
Drip edge
Starter Shingle Roll adhered
directly to Underlayment and
primed drip edge
6.3 ASPHALT SHINGLES:
6.3.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions:
➢ Berkshire® shingles require minimum five (5) nails per shingle.
➢ WeatherGuard® HP shingles require minimum six (6) nails per shingle.
Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required
Refer to Owens Corning published information on wind resistance and installation limitations.
6.3.1.1 Supreme:
Normal
Wind Areas
Area pare vientos normales
V
5" Exposure
Exposicion
Mansard or Area para
High Wind desvanes V
Areas vientos fuertes
rV 2" (BI r2"
Figure 4: Minimum Nailing, Supreme
(Standard Size)
Normal Mansard or Area para
Wind Areas High Wind desvanes q
Area para vientos normales Areas vientos fuertes
Utz t {AI t2 t �. Z j1" 2` (BI r2„ i.,
5 518" Exposure
Exposicion
Figure 5: Minimum Nailing, Supreme
(Metric Size)
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 5 of 10
6.3.1.2 Berkshire®:
Figure 6: 5-Nail Pattern, Berkshire
ONEMOjetc.
Sealant strip
La Lira de sellador
B 112,� 8112.. 8 112" S 112
''
1
1
Figure 7: 6-Nail Pattern, Berkshire
Sealant strip
La tira de selladar
0- 01 4 ---------- s • • 4 ---------- ► 9 t--r •
s vt' s vt' s art'
1
1
1
Asphalt roofing cement
Cemonto do Who do astatto
Figure 8: Mansard or Steep Slope Pattern, Berkshire
NEMO ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 6 of 10
*NEMO I etc.
6.3.1.3 Duration® Premium, TruDefinition® Duration, Duration® Premium COOL & TruDefinition® Duration® Designer Color
Collection:
Figure 9: Standard 4-Nail Pattern, Duration
6-Nail Fastening Pattern
SureNail(D fastening area width
Nail, Typical
A" 12"
a n ..a� �m .. _ �......... - ....... - -
iRwens Coming SureNailEl I- El
� �. 5 C suarnp � Dwens Corning SureNa �
6-118" 5.518"
epasure
Figure 10: 6-Nail Pattern, Duration
Fastening for Slopes Greater Than 21:12
SureNail® fastening area width
Nail, Typical
1„ 12" 12"
Owens Cw in95ureNad �_L
6wwo)suainp Owem Coming SureNail®
fi-11fi" 5-518"
e[posure
T",
Four 1" Spots of Asphalt Roofing Cement
Figure 11: Mansard or Steep Slope Pattern, Duration
NEW ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 7TN EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 7 of 10
6.3.1.4 TruDefinition®Oakridge®, Oakridge®:
4 Nail Pattern
Esquema con 4 clavos
1" 1„
I� 12° 12"
5519" Exposure Nails 5 519" Exposure
Exposid6n de 418pulg. Caavos Exposicicn de 55/8pulg.
Figure 12: Standard 4-Nail Pattern, Oakridge
*NEMO I etc.
6 Nail Pattern
Esquema con S clavos
IF 12° 12"
Nails
5 519" Exposure Claws 5 518" Exposure
Exposicidn de 5 518 pulp. Fxposlcidn de 6 618 ping.
Figure 13: 6-Nail Pattern, Oakridge
Fastening for Slopes Greater Than 21:12
SureNail i fastening area width
Nail, Typical
1„ 12„
pwms Coming SamNar] • •ir amS Buiwo�sualnp • Oweio<Camine SureNail® •
6.118" 5.5lB"
e,gusure
Four t" Spots of Asphalt Roofing Cement
Figure 14: Mansard or Steep -Slope Pattern, Oakridge
6.3.1.5 WeatherGuard® HP:
� �17q\\ -
V3ik �13m5s
5 5-8' Exposure 5 W
Expasira80 de 5 5�13 pulp. fx"Gkidn de 5 ping.
Figure 15: 6-Nail Pattern, WeatherGuard HP
6 N al Pattern
Esquama con 6 clavos
5 5T Exposure
Exposmon de 5 5;8 pulp.
Nail 6 10 from bottom
of shingle
GIavo a 6 V8 pulp. de la
6 Fasteners pane inferior de h teja
6 sujoadures
Four 1" Spots of Asphalt Roof Gameni
Cuatry Pun tos de cemarfto de team da aSWO de 7 pulgada
Figure 16: Mansard or Steep -Slope Pattern, WeatherGuard HP
NEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 8 of 10
NNEMO I etc.
6.4 HIP AND RIDGE SHINGLES:
6.4.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions.
➢ Berkshire® Hip and Ridge Shingles with Sealant and DuraRidge° Hip and Ridge Shingles with Sealant require
minimum two (2) nails per shingle.
➢ WeatherGuard® HP Hip and Ridge Shingles and ProEdge° require minimum four (4) nails per shingle.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.4.1.1 Berkshire® Hip and Ridge with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant:
Fig. A
Prevailing Wind Direction
Direccion del viento predominante
4
Nails
Clavos 4
y
I
A I
4 I I I
I I I I
I
8° Exposure
rosicion de 8 pulg
4
A
Figure 17: Isometric View, Berkshire and DuraRidge
6.4.1.2 WeatherGuard® HP Hip and Ridge Shingles:
Fig. A 4 4
Prevailing Wind
t Direction p
A
Nails 4 4
A i I
p I I
44
I I
I I I I
A
A I I I I
I I I I
Exposure
Fig. B
Top View
Vista superior
Nail
25/s r clavo
• Owens Corning SureNail' •
I
I
I�
CD
CD
CI e
I
I
12"
Figure 18: Plan View, Berkshire and DuraRidge
Fig. C Hip & Ridge Shingle Fastening
To p V lew
Nails Nails
2" 2"
11
1 �•
5 Exposure
12
Figure 19: Isometric View, WeatherGuard HP Hip and Ridge Figure 20: Plan View, WeatherGuard HP Hip and Ridge
NEMO ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 9 of 10
6.4.1.3 ProEdge®:
Prevailing
Wind Direction Sealant Strip
Ak--- 6" Exposure
Fasten Th"
Cover Exposed
Fasteners with
Roof Cement
Figure 21: Isometric View, ProEdge
ONEMC
Standard
Fastening
Pattern
12' •I 44 Sealant
,x
7 ��„ Exposure
Figure 22: Plan View, ProEdge
As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this
product.
Contact the named CIA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements. Refer
to Section 4 herein for products and production locations having met codified material standards.
PRI Construction Materials Technologies, LLC— QUA9110 ; 813 621-5777; bwilson@pricmt.com
- END OF EVALUATION REPORT -
NEMO ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 10 of 10