Loading...
HomeMy WebLinkAboutAPPROVED Revised Product Approvals Sliding Glass DoorsNOA No. 21-0205.03 Expiration Date: April 14, 2026 Approval Date:March 25, 2021 Page 1 MIAMI -DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy PGT Industries, Inc. 1070 Technology Drive, North Venice, FL 34275 S COPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has b een designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Series “5570/2770” Vinyl Sliding Glass Door (Reinforced) w/wo 900 & 1350 corners-L.M.I. APPROVAL DOCUMENT: Drawing No. MD-5570 .0 Rev B, titled “Vinyl Sliding Glass Door N OA (LM)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15 and last revised on 02/01/21, signed and sealed by A. Lynn Miller, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami-Dade County Product Control Section.MISSILE IMPACT RATING: Large and Small Missile Impact Resistant Limitations: 1.See table 1 (sheet 7 ) and table 2 (sheet 8) for applicable SGD unit sizes, design pressures , reinforcements types, glass types, sill riser (see tables B-1 & B-2, sheet s 7-8) and anchor layout sheets requirements in 11 thru 16. 2.Rigid White PVC, Tan (Non -white) Rigid PVC and Brown coated (Painted or laminated) white Rigid PVC to be labeled per referenced NOA’s requirements.3.Egres s operable do ors must comply with min clear width or height per FBC requirement, as applicable. 4.Pocket walls under separate approval, to be reviewed b y Building officialLABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and series and following statement: "Miami-Dade County Product Control Approved", noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises & renews NOA #20-04 29.05 and consists of this page 1 and evidence p ages E-1, E-2, E-3, E-4 , E-5 & E-6 as well as approval document mentioned above . The submitted documentation was reviewed by Ishaq I. Chanda, P.E . Ishaq I. Chanda , P.E. Product Contro l Unit Supe rvisor NOA No. 21-0 205.0 3 Expiration Date: April 14, 2 026 Approval Date: Ma rch 25, 2021 E -1 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1.Evidence submitted under previous NOA A. DRAWINGS 1.Manufacturer's die drawings and sections. (Submitted under NOA No. 11-0107.04) 2. Drawing No. MD -5570.0, titled “Vinyl Sliding Glass Door NOA (LM)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15, with revision A dated 04/05/17, sign ed and sealed by A. Lynn Miller, P.E. B. TESTS 1. Test report on 1) Uniform Static Air Pressure Test, per FBC, TAS 202-94 2) Large Missile Impact Test per FBC, TAS 201-94 3) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along wit h marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 8717, dated 12/07/15, signed and sealed by Idalmis Ortega, P. E. (Test report revised on 02/15/16 and 02/2 4/16) 2. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC, TAS 202-94 along with marked-up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 8546, dated 11/06/15, signed and sealed by Idalmis Ortega, P. E. (Test report revised on 01/04/16 and 02/11/2016) 3. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5)Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC, TAS 202-94 along with marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 8547, dated 12/0 4/15, signed and sealed by Idalmis Ortega, P. E. (Test report revised on 02/15/16) 4. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC, TAS 202-94 along with marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 8548, dated 12/04/15, signed and sealed by Idalmis Ortega, P. E. (Test report revised on 01/04/16 and 02/11/16). Ishaq I. Chanda , P.E. Product Contro l Unit Supe rvisor NOA No. 21-0 205.0 3 Expiration Date: April 14, 2 026 Approval Date: Ma rch 25, 2021 E -2 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED B.TESTS (continued) 5. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2)Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC, TAS 202-94 along with marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 8549, dated 11/06/15, signed and sealed by Idalmis Ortega, P. E. (Test report revised on 12/04/15 and 02/11/16) 6. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along with marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 8552, dated 12/0 4/15, signed and sealed by Idalmis Ortega, P. E. (Test report revised on 02/15/2016) 7.Test report on 1) Uniform Static Air Pressure Test, per FBC, TAS 202-94 2) Large Missile Impact Test per FBC, TAS 201-94 3) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along with marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 6638 (samples A -1 thru A-22), dated 11/19/10, signed and sealed by Jorge A. Causo, P. E. (Submitted under NOA No. 11- 0107.04) 8 Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC, TAS 202-94 along with marked -up drawings and installation diagram of vinyl sliding glass door, prepared by Fenestration Testing Lab, Inc., Test Report No. FTL 6337 (samples A -1 thru A-5), dated 12/06/10, signed and sealed by Jorge A. Causo, P. E. (Submitted under NOA No. 11- 0107.09) C. CALCULATIONS 1.Anchor verification calculations and structural analysis, complyin g with F BC-2014, prepared by PGT, dated 12/09/15and last revised on 02/15/16, signed and sealed by Anthony L. Miller, P.E. (Submitted under NOA No. 15-1210.01). 2.G lazing complies with ASTME -1300-09. Ishaq I. Chanda , P.E. Product Contro l Unit Supe rvisor NOA No. 21-0 205.0 3 Expiration Date: April 14, 2 026 Approval Date: Ma rch 25, 2021 E -3 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED D.QUALITY ASSURANCE 1.Miami Dade Department of Regulatory and Economic Resources (RER). E.MATERIAL CERTIFICATIONS 1.Notice of Acceptance No. 15-0528.14 issued to Vision Extrusion Limited for their “White Rigid PVC Exterior Extrusions for Windows and Doors”, dated 08/13/15, expiring on 09/30/19. 2.Notice of Acceptance No. 16-0920.08 issued to Visio n Extrusion Limited for their “VE 1000 Tan 202 and lighter Shades (Non-White) Rigid PVC Exterior Extrusions for Windows and Doors”, dated 12/08/16, expiring on 12/29/21. 3.Notice of Acceptance No. 15-0528.15 issued to V ision Extrusion Limited for their “Brow n Coated (Painted or Laminated) White Rigid PVC Exterior Extrusions for Windows and Doors”, dated 08/13/15, expiring on 09/30/19. 4.Notice of Accept ance No. 16-0712.02 issued to ENERGI Fenestration Solutions USA, Inc. f or their “TAN 3040 and Lighter Shades (Non-White) Rigid PVC Exterior Extrusions for Windows and Doors” dated 09/15/16, expiring on 02/04/21. 5.Notice of Acceptance No. 16-0712.04 issued t o ENERGI Fenestration Solutions USA, Inc. for their “Bronze and Lighter Shades of Cap Coated Rigid PVC Exterior Extrusions for Windows and Doors” dated 09/15/16, expiring on 04/16/20. 6.Notice of Acceptance No. 16-0712.03 issued to ENERGI Fenestration Solutions USA, Inc. for their “White Rigid PVC Exterior Extrusions for Windows and Doors” dated 08/10/17, expiring on 02/28/18. 7. Test reports No(s). 10-002-792(A), 10-06-M0527, 535753-09, per ASTME-84, ASTMD1929 and ASTMD-635, issued by EXOVA to Vision Extrusion for cellulosic composite material. (Submitted under NOA No. 11-0107.04) 8.Notice of Acceptance No. 14-0916.11 issued to Kuraray America., Inc. for their “SentryGlas® (Clear and White) Interlayer”, expiring on 07/04/18. 9. Notice of Acceptance No.16-1117.01 issued to Kuraray America, Inc. for their “Trosifol® Ultraclear, Clear and Color PVB Interlayers”, expiring on 07/08/19. F.STATEMENTS 1.Statement letter of conformance with FBC-5th Edition (2014) and FBC-6th Edition (2017), issued by manufacturer, dated 08/14/17, signed & sealed by Lynn Miller, P .E. 2.Statement letter of no financial interest, dated 04/18/17, issued by manufacturer, signed & sealed by Lynn Miller, P.E. 3.Letter of lab compliance, part of the above test reports. 4.RER Test Proposal No. 17-0387, d at ed 05/05/17, signed by Ishaq Chanda, P.E. G.OTHER 1.Notic e of Acceptance No. 15-1210.01, issued to PGT Industries, for their Series “5570/2770” Vinyl Sliding Glass Door (Reinforced) – L.M.I.”, expiring on 04/14/21. Ishaq I. Chanda , P.E. Product Contro l Unit Supe rvisor NOA No. 21-0 205.0 3 Expiration Date: April 14, 2 026 Approval Date: Ma rch 25, 2021 E -4 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 2.Evidence Submitted under previous submittal A. DRAWINGS 1.Drawing No. MD -5570.0 Rev B, titled “Vinyl Sliding Glass Door NOA (LM)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15 and last revised on 04/22/20, signed and sealed by A. Lynn Miller, P.E. B. TESTS 1.Te st reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4)Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along with marked -up drawings and installation diagram of all PGT Industries, Inc. representative units listed below and tested to qualify Dowsil 791 and Dowsil 983 silicones, prepared by Fenest ration Testing Laboratory, Inc., Test Report s No.: FTL-7897, PGT PW5520 PVC Fixed Window (unit 6 in proposal), dated 09/03/14 FTL-20-2107.1, PGT SGD780 Aluminum Sliding Glass Door (unit 7 in proposal) FTL-20- 2107.2, PGT CA740 Alum. Outswing Casement Wind ow (unit 8 in proposal) FTL-20- 2107.3, PGT P W7620A Aluminum Fixed Window (unit 9 in proposal) and FTL-20-2107.4, PGT PW7620A Aluminum Fixed Window (unit 10 in proposal) dated 07/1 3/20, all signed and sealed by Idalmis Ortega, P.E. C.CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 7th E dition (2020), dated 04/22/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2.Glazing complies with ASTM E1300-04, -09, -12 and -16. D.QUALITY ASSURANCE Miami-Dade Department of Regulatory and Economic Resources (RER). E.MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for their “Trosifo l® Ultraclear, Clear, and Color PVB G lass Interlayers”, expiring on 07/08/24. 2.Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 3.N otice of Acceptance No. 18-1106.10 issued to Vision Extrusions Limited for their “Brown Coated (Painted or Laminated) White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 09/30/24. 4.Notice of Acceptance No. 18-1106.11 issued to Vision Extrusions Limited for their series “V E 1000 Tan 202 and lighter shades (Non–White) Rigid Cellular PVC Exterior Extrusions for Windows and Doors”, expiring on 12/29/21. Ishaq I. Chanda , P.E. Product Control Unit Supervisor NOA No. 21-0205.03 Expiration Date: April 14, 2026 Approval Date: March 25, 2021 E -5 CGI Windows and Doors, Inc. NOTICE OF A CCEPTANCE: EVIDENCE SUBMITTED E. MATERIAL CERTIFICATIONS (continue) 5.Quanex Part Super Spacer Standard complying with ASTM C518 Thermal Conductivity 0.881 BTU -in/ hr.-ft²-°F, ASTM F 1249 WVTR -Pass, ASTM D 3985 Oxygen–Pass, ASTM E 2190 I.G. Durability-No Fog-Pass. (Submitted under previous NOA No. 15-0409.05) 6.Quanex Part Duraseal complying with ASTM C518 Thermal Conduct ivity 2.22 BTU -in/ hr.-ft²-°F , ASTM F 1249 WVTR-Pass, ASTM D 1434 Argon Permeance-Pass, ASTM E 2189 I.G. Durability-No Fog, ASTM E 546 Dew Point Development -20o F in 48 hrs. (Submitted under NOA No. 15-0409.05). 7.Vision Extrusions, Ltd. Parts comply ing with PVC-AAMA 303-13, Voluntary Specification for Rigid Polyvinyl Chloride (PVC) Exterior Prof iles for Vision Extrusions, Ltd.-VEX-1 by AAMA Fenestration Exterior Prof ile Certification Program. (Submitted under NOA No. 15- 0409.05) 8.Vision Extrusions, Ltd. Parts complying with PVC-AAMA 303-13. (Submitted under NOA No. 15-0409.05) 9.PVC-AAMA 303-13, Voluntary Specification for Rigid Polyvinyl Chloride (PVC) Exterior Profiles for Vision Extrusions, Ltd.-VEX-1 by AAMA Fenestration Exterior Profile Cert if ication Program. 10.Notice of Acceptance No. 18-1217.14 issued to Energi Fenestration Solution, USA, Inc. for their “Tan 3040 & light shade (non-white) White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 02/04/21. 11.Notice of Acceptance No. 18-0122.02 issued to Energi Fenestration Solution, USA, Inc, for their series “White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 02/28/23. 12. N otice of Acceptance No. 20-0203.03 issued to Energi Fenestration Solution, USA, Inc. for their “Bronze & light shade cap coated White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 04/16/25. F.STATEMENTS 1.Statement letter of conf ormance to FBC 7 th Edition (2020), dated 04/22/20, issued by manufacturer, sign ed and sealed by Anthony Lynn Miller, P.E. 2.Statement let ter of no financial interest and of independent, issued by manufacturer, dated 04/18/20, signed and sealed by Anthony Lynn Miller, P.E. 3.Private Labeling A greement document between PGT, d ated 03/30/15 and signed by all involved parties. G.OTHERS 1.This NOA revises NOA# 17-0420.06 (PVT w/CGI) and updates to FBC2020 (7th Edition), expiring 04/21/2 1. 2.RER Test proposals #19-1155 dated 01/10/20 approved by Ishaq I . Chanda, P.E, expiring 04/14/2 1. Ishaq I. Chanda , P.E. Product Control Unit Supervisor NOA No. 21-0205.03 Expiration Date: April 14, 2026 Approval Date: March 25, 2021 E -6 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 3.New Evidence Submitted A. DRAWINGS 1.Drawing No. MD -5570.0 Rev B, titled “Vinyl Sliding Glass Door N OA (LM)”, sheets 1 through 21 of 21, prepared by manufacturer, dated 10/05/15 and last revised on 02/01/2 1, signed and sealed by A. Lynn Miller, P.E. Note: This revision consists replacement of same existing installation screw with flat head. B. TESTS 1.None. C. CALCULATIONS 1. None. D.QUALITY ASSURANCE 1.Miami-Dade Department of Regulatory and Economic Resources (RER). E.MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for t heir “Trosifol® Ultraclear, Clear, and Color PVB G lass Interlayers”, expiring on 07/08/24. 2.Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 3.Notice of Acceptance No. 18-1106.10 issued to Vision Extrusions Limited for their “Brown Coated (Painted or Laminated) White Rigid PVC Exterior Extrusions for Windows and Doors”, expiring on 09/30/24. 4.Notice of A cceptance No. 18-1106.11 issued to Vision Extrusions Limited f or their series “VE 1000 Tan 202 and lighter shades (Non–White) Rigid Cellular PVC E xterior Extrusions for Windows and Doors”, expiring on 12/29/21. F.STATEMENTS 1.Statement letter of conformance to FBC 7 th Editio n (2020), dated 02/01/21, issued by manufacturer, sign ed and sealed by Anthony Lynn Miller, P.E. 2.Private Labeling Agreement dated 03/08/21 between PGT Industries, Inc. and CGI Windows and Doors Inc., signed by Dean M. Ruark, P.E., V.P. Engineering, on behalf of both companies. G.OTHERS 1.This NOA revises & renews NOA# 20-0429.05 (PLA w/CGI), expiring 04/14/2 6. 2.Th e current associated PLA CGI file #21-0205.01, expiring 04/14/2 6.