HomeMy WebLinkAboutSTEEP SLOPE ROOF SYSTEMT LUC E
Section D (Steep Slope Roof System)
Roof System Manufacturer: Tamko Building products
Notice of Acceptance Number:
FI # 18355-R6
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1:-38. 1 Zone 2e: -502 Zone 2n: -50.2 Zone 2r: -49.6 Zone 3e: -50.2 Zone 3r: -50.2
Deck Type: 119/32 CDX' Plywood
f
Roof Slope: Type Underiayment: I Install new tri-built peel & stick
4:12 Insulation; I N/A
Fire Barrier: I N/A
Rid v VAentifation? Fastener Type & Spacing: 1-1/4" x .120 Coil Nails / 6 nails pattern = 1-2-2-1
Adhesive Type- N/A
Type Cap Sheet: N/A
Mean Roof Height: 12' Roof Covering: Shingle /Tamko
Type & Size Drip 2° x�/Al,-,nurn
Edge:.
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component is not used, identify as "NA")
System Manufacturer: POLYGLASS USA
Product Approval No.: FL#1654-R27
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1':-36.1 Zone 1: -36.1 Zone 2: -47.7 Zone 3: -64.9
Max. Design Pressure, from the specific product approval
system: Peel & stick / SBS-SA
Deck:
Type: Plywood
Gauge Thickness: 19132 CDX
Slope: 1/12
Anchor/Base Sheet & No. df Ply(s): N/A
Anchor/Base Sheet Fastener/Bonding Material:
N/A
Insulation Base Layer: NIA
Base Insultation Size and Thickness: N/A
Base Insulation Fastener/Bonding Material:
N/A
Top Insulation Layer: NIA
Top Insulation Size and Thickness: N/A
Top Insulation Fastener/Bonding Material:
N/A
Base Sheet(s) & No. of Ply(s): 1
Base Sheet Fastener/Bonding Material:
SELF -ADHERING
Ply Sheet(s)' & No. of Ply(s): N/A
Ply Sheet Fastener/Bonding Material:
N/A
Top Ply: 1
Top Ply Fastener/Bonding Material:
SELF -ADHERING
Surfacing: N/A
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—"
oc @ Lap, # Rows
@ "oc
Zone 1:_"
oc @ Lap, # Rows
@ "oe
Zone 2:_"
oc @ Lap, # Rows
@ "on
Zone 3:—"
oc @ Lap, # Rows
@ "oo
Number of Fasteners Per Insulation Board:
Zone 1': Zone 1: Zone 2: Zone 3:
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc..
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16. .
T LUCIE
Section A (General Information)
Master Permit No.
Process No.
Contractors Name: ONE CONSTRUCTION & ROOFING CONTRACTORS, INC License # CCC-1330623
Job Address 4712 Seagrape Dr. Fort Pierce, FI 34982
ROOF CATEGORY
X Low Slope ❑ Mechanically Fastened Tile ❑ Mortar/Adhesive Set Tiles
XAsphaitic Shingles ❑ Metal Panel/Shingles ❑Wood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE.
❑ New roof ❑ Repair ❑ Maintenance X Reroofing ❑ Recovering
ROOF SYSTEM INFORMATION
ft. Total(SF)2,1a1 sq.
ft
Low Slope Roof Area (SF) 501 sq ft Steep Sloped Roof Area (SF) 1680 sq.
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
('!^o )