Loading...
HomeMy WebLinkAboutEVALUATION REPORTNEW I etc. Certificate of Authorization #32455 353 Christian Street, Unit #13 Oxford, CT 06478 (203) 262-9245 ENGINEER EVALUATE TEST CONSULT Owens Corning One Owens Corning Parkway Toledo, OH 43659 (740) 404-7829 Evaluation Report 037940.02.12-Rll FL10674-1116 Date of Issuance: 02/06/2012 Revision 11: 12/11/2020 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the 7th Edition (2020) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof'Shingles LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted herein and FBC 1507.2.7.1 / R905.2.6.1 CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change. Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any changes to the product(s), the Quality Assurance or the production facility location(s). NEIVIO ETC, LLC requires a complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words "NEMOIetc. Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Reportshall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 10. Prepared by: Robert J.M. Nieminen, P.E. .ti Q,,-"4. The facsimile seal appearing was authorized by Robert ,''%.;°�^; ^'= ^��'? Nieminen, P.E. on 12/11/2020. This does not serve as an Florida Registration No. 59166, Florida DC4 ANE1983 electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. NEMO ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. ©2018 NEMO ETC, LLC CODY • ONEMOletc. ROOFING SYSTEMS EVALUATION: Product Category: Roofing Sub -Category: Asphalt Shingles Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated compliance with the following sections of the 7th Edition (2020) Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: -Section Pro a Standard Year, 1507.2.4, R905.2.3 Physical Properties ASTM D1970 2015 1507.2.5, R905.2.4 Material standard ASTM D3462 2010 1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D3161 2016 1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D7158 2019 3. REFERENCES: Entity Examination_ Reference - Date Owens Corning Declaration Equivalency Declaration 08/06/2019 PRI(TST5878) ASTM D1970 OCF-382-02-01 10/24/2017 UL LLC (CER9626) Physicals & Wind Resistance File R2453, Vol. 3 02/15/2007 UL LLC (CER9626) Physicals & Wind Resistance 20120516-112453 05/16/2012 UL LLC (TST9628) Physical Properties 06CA20263 04/18/2006 UL LLC (TST9628) Wind Resistance 11CA34308 02/18/2012 UL LLC (TST9628) Physicals & Wind Resistance 4786093137 02/01/2014 UL LLC (TST9628) Wind Resistance 4786126532 02/10/2014 UL LLC (TST9628) Physical Properties Classification letter 02/13/2014 UL LLC (TST9628) Physical Properties Classification letter 10/02/2015 PRI (QUA9130) Quality Control Service Confirmation 04/05/2020 PRI (QUA9110) Quality Control Florida BCIS Current TABLE 1: ASPHALT SHINGLE COMPONENTS Type Product Plant(s) " Material Standard Description Starter Strip Shingle H-TX, OR Starter Strip Plus MN, OR Accessory ASTM D3462 starter strips for asphalt roof shingles SRS TopShield Starter MN, OR Starter Strips Starter Shingle Roll NH ASTM D1970 mineral -surfaced, fiberglass -reinforced, self -adhering SBS modified bitumen starter Supreme' GA, CA, CO, I -TX, NJ, OH, ASTM D3462 fiberglass reinforced 3-tab asphalt TN, OR, IL roof shingles Berkshire' MN ASTM D3462 fiberglass reinforced, 4-tab asphalt roof shingles Duration' Premium CA, OR Duration' Premium COOL CA Asphalt TruDefinition' Duration' Shingles IN, CA, CO, I -TX, FL, NJ, OH, TruDefinition Duration Designer Color Collection MN, OR, GA, IL, TN ASTM D3462 fiberglass reinforced, laminated asphalt roof shingles Oakridge' GA, IN, CA, CO, H-TX, I -TX, FL, NJ OH, TN TruDefinition' Oakridge' H-TX, I -TX WeatherGuard' HP TN NEMO ETC, LLC Certificate of Authorization #31455 7" ED , ON-HVHZ EVALUATION Owl s Co n ng Asphalt Roof Shingles Evaluation Report 037940.02.12-Rii F1.10674-1116 Revision 11:12/11/2020 Page 2 of 10 ONEMOletc. TABLE 1: ASPHALT SHINGLE COMPONENTS Type Product Plant(s) Material Standard Description Berkshire' Hip and Ridge Shingles with Sealant MN DuraRidge® Hip and Ridge MN Hip and fiberglass reinforced, hip and ridge Ridge Shingles with Sealant ASTM D3462 asphalt roof shingles ProEdge® GA, CA, OH; OR Shingles WeatherGuard' HP Hip and Ridge Shingles TN 5.1 This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC High Velocity Hurricane Zone jurisdictions (i.e., Broward and Miami - Dade Counties). 5.3 This Evaluation Report pertains to above -deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. 5.4 This Evaluation Report does not include evaluation of fire classification. Refer to FBC 1505 for requirements and limitations regarding roof assembly fire classification. Refer to FBC 2603 for requirements and limitations concerning the use of foam plastic insulation. 5_5 Wind Classification: Refer to Section 6 for installation requirements to meet wind classifications 5.5.1 TABLE 2A: WIND CLASSIFICATIONS, ASPHALT SHINGLES Product FBC Table 1507.2.7.1 or R905.2.6.1 Supreme' ASTM D3161(F) & ASTM D7158(H) Berkshire' Duration' Premium Duration' Premium COOL TruDefinition' Duration' TruDefinition' Duration' Designer Color Collection Oakridge' TruDefinition' Oakridge WeatherGuard' HP Classification by ASTM D7158: ASTM D7158, Class H applies only to exposure category B or C and a building height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. a NEMO ETC, LLC ��` - 4 Evaluation Report 037940.02.12-1111 Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 3 of 10 ONEM01 etc. TABLE 2B: WIND CLASSIFICATIONS,STARTER'STRIPS AND HIP gt RIDGE Type . Product FBC Table 1507.2.7.1 or R905.2.15A Starter Strips Starter Strip Shingle ASTM D3161, Class F Starter Strip Plus SRS TopShield Starter Hip &Ridge Shingles Berkshire' Hip and Ridge Shingles with Sealant ASTM D3161, Class F DuraRidge® Hip and Ridge Shingles with Sealant ProEdge® WeatherGuard' HP Hip and Ridge Shingles 5.5.2 Refer to Owens Corning published information on wind resistance and installation limitations. 5.6 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3. Refer to the Product Approval of the component manufacturer for components that are produced by a Product Manufacturer other than the report holder on Page 1 of this Evaluation Report. 6.1 GENERAL: 6.1.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle manufacturer's minimum requirements. 6.1.2 Underlayment shall be acceptable to the shingle manufacturer and shall hold current Florida Statewide Product Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3. 6.1.3 Fasteners shall be in accordance with the shingle manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.1.4 Owens Corning asphalt shingles are acceptable for use in reroof (tear -off) or recover applications, subject to the limitations set forth in FBC Section 1511 or R908 and published installation instructions. 6.2 ACCESSORy STARTERS: 6.2.1 Installation of Starter Strip Shingle, Starter Strip Plus and SRS TopShield Starter shall comply with the Owens Corning current published instructions, using minimum five (5) nails per strip. Felt undedayment Deck Self -adhered WeatherLocke umderlaymem Drip edge Drip edge w ' Nails located 2"-3" from save Install first Self-sealing adhesive Starter Strip _ positioned along eave shingle with 6" removed Starter Strip shingle overhangs eaves and rakes '/i -1/1' Felt undedayment Deck SO"hered Weatherl odA undodayment Drip edge Drip _. edge w' Nels located " from ewe Install first Strip Plus Sefaesgng adhesive lil with V removed positioned along saw Starter Strip Plus overhangs ewes and rakes 1149-31 r Figure 1: Minimum Nailing, Starter Strip Figure 2: Minimum Nailing, Starter Strip Plus NEMO ETC, LLC Evaluation Report 037940.02.12-Rll Certificate of Authorization N32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 4 of 10 ONEMOjetc. 6.2.2 Installation of Starter Shingle Roll shall comply with the Owens Corning current published instructions. Underlayment Drip edge Starter Shingle Roll adhered directly to underlayment and primed drip edge Self-sealing adhesive positioned along eaves Figure 3: Starter Shingle Roll 6.3 ASPHALT SHINGLES: 6.3.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions: ➢ Berkshire` shingles require minimum five (5) nails per shingle. ➢ WeatherGuard® HP,shingles require minimum six (6) nails per shingle. Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required Refer to Owens Corning published information on wind resistance and installation limitations. 6.3.1.1 Supreme: Normal Mansard or Area pare Wind Areas High Wind desvenes y Area pare vientos norrrrales Areas vientos faertes t r' n• S'Exposure Exposieion r1- 2• (B 2• �. Figure 4: Minimum Nailing, Supreme (Standard Size) Normal Wind Areas Area pare vientos nonnales �2 u . 5 5/8" Exposure Exposieidn Mansard or Area pare High Wind deavenes y Areas vientos fuartes ri V 2" (BI r2. t. Figure 5: Minimum Nailing, Supreme (Metric Size) NEMO ETC, LLC Evaluation Report 037940.02.12-Rll Certificate ofAuthorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page S of 10 6.3.1.2 Berkshire®: Figure 6: S-Nail Pattern, Berkshire O-NEMOjetc. Sealant strip La tlra de sellador 8 o i S W I S tY. i 8 th..'.. , Figure 7: 6-Nail Pattern, Berkshire Figure 8: Mansard or Steep Slope Pattern, Berkshire NEW ETC, LLC Evaluation Report 037940.02.12-1111 Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 6 of 20 ONEMOletc. 6.3.1.3 Duration® Premium, TruDefinition® Duration, Duration® Premium COOL & TruDefinition* Duration* Designer Color Collection: 4-Nail Fastening Patter SONNail®fastenine area widtti Nail,;lypieal pis co":�w s��.w��. • ' me . �a v.,� wa.a • oWens cnm6ie SueNaaB � • Figure 9: Standard 4-Nail Pattern, Duration 6-Nail Fastening Pattern SuteNail®fastening area width Nail' -Typical 17 12:' 12" 1" peens Comic 9 SurtNal • ?N S �+.�� sw • • aWe+is Cwnc.p SueNai® �• eipoecve--F] EJ I Figure 10: 6-Nail Pattern, Duration Figure 11: Mansard or Steep Slope Pattern, Duration NEMO ETC, LLC Evaluation Report 037940.02.12-1111 Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 7 of 10 6.3.1.4 TruDeffnition'Oakridae®.Oakrfdge®: '4`Nall Paftern 'Esquema c0-4:c1avos, T, 664, Exposure Nags 5',5/8 Exposure Fxposid6a de f e1q,puig. �av Expnsruorr de,5 b%Spuig. Figure 12: Standard 4-Nail Pattern, Oakridge 6.3.1.5 WeatherGuard® HP: '6 Nall hiterti -Esqueriia coh 6 davos 6618" Expasule; Exposleidn de 55/8 puig. 00NEM01etc. 'ii 5 618" Exposure. ' Fxpostribriile 55/8p+rlg. Figure 13: 6-Nail Pattern, Oakridge Fastening for Slopes Greater Than 21:12 SureNall9 rastening area width Nail, Typical fwcYal • • ars avm�,w.o • owmca"mo! Four 7" Spots of Asphalt Roofing Cement 6 Nai Pattern Esquema con 6 clavos Nail 61W from bottom of shingle 5 518' Exposure 6 Fasteners Cleve a 6 118 deli. de la Eapor1ci5n ode 5 518 puig. 6 sWetadores pie inferior de li teja tF 12 p tg12 2 lg109� 5 SJa; E�roue 5 5rs.F�a wa Four 1 " Spots of Asphalt Roof Cement Ezposaobn de 5 5B puig hpaiGn do 5 6!8 puig. Cuatro defiles de cemefito de tedra de as/alto de 1 puJgada Figure IS: 6-Nail Pattern, WeatherGuard HP Figure 16: Mansard or Steep -Slope Pattern, WeatherGuard HP NEMO ETC, LLC Evaluation Report 037940.02.12-1111 Certificate of Authorization #32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 8 of 10 NEMO I etc. 6.4 HIP AND RIDGE SHINGLES: 6.4.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions. ➢ Berkshire Hip and Ridge Shingles with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant require minimum two (2) nails per shingle. ➢ WeatherGuard* HP Hip and Ridge Shingles and ProEdge® require minimum four (4) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations. 6.4.1.1 Berkshire® Hip and Ridge with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant: Fig. A I cl Prevailing Wind Direction Direccion del viento predominante ' I I I I rbp 8 ci6n do e osiExp s 8 Qul ZN�A Figure 17: Isometric View, Berkshire and DuraRidge 6.4.1.2 WeatherGuard® HP Hip and Ridge Shingles: rig.A, Prevalling Wind Direction q:q A A i A\\ I I I I I. I Expo"sure Figure 19: Isometric View, WeatherGuard HP Hip and Ridge rigure ms: Tian view, tserKsnire ana uuraKiage Fig. C Hip &Ridge ghigle Fastening T60low Naps, Nails T' T s.. Erposure 12" Figure 20: Plan View, WeatherGuard HP Hip and Ridge NEMO ETC, LLC Evaluation Report 037940.02.12-R31 Certificate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 9 of 10 6.4.1.3 ProEclae®: Prevailing Wind Direction Soalxnt Strip G' Exposure Fasten 71h° Cover Exposed Fasteners with Roof Cement Figure 21: Isometric View, ProEdge ONEMOjetc. Standard Fastening Pattern �-'I �''•� il'� I--i i2• Sealant 1 ° G" Exposure Figure 22: Plan View, ProEdge REQUIREMENTS: 1-7. BUILDING PERMIT As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this product. Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements. Refer to Section 4 herein for products and production locations having met codified material standards. PRI Construction Materials Technologies, LLC—QUA9110; 813 621-5777; bwilson@pricmt.com - END OF EVALUATION REPORT - NEMO ETC, LLC Evaluation Report 037940.02.12-1111 Certiftate of Authorization #32455 7T" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116 Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020 Page 10 of 10