HomeMy WebLinkAboutSLIDING GLASS DOORBYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJASHWINCO ARCHITECTURAL PRODUCTS, LLC
SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZ
INSTALLATION ANCHORAGE DETAILSGENERAL NOTES:
1.THIS PRODUCT HAS BEEN TESTED, EVALUATED AND DESIGNED TO THE DESIGN PRESSURE(S) STATED HEREIN IN
ACCORDANCE WITH THE REQUIREMENTS OF THE CURRENT EDITION OF THE FLORIDA BUILDING CODE INCLUDING
THE HIGH VELOCITY HURRICANE ZONE (HVHZ). THIS PRODUCT CAN BE USED IN THE HIGH VELOCITY HURRICANE
ZONE (HVHZ).
2.THE PRODUCT DETAILS CONTAINED HEREIN ARE BASED UPON SIGNED AND SEALED UL TEST REPORT NO.
SV31355-20190517-REPORT-A AND ASSOCIATED LABORATORY DRAWINGS BY NATIONAL CERTIFIED TESTING
LABORATORIES.
2.1.PERFORMANCE STANDARDS USED IN TESTING FOR HVHZ LOCATIONS WERE TAS 201-94, TAS 202-94 AND TAS
203-94.
2.2.PERFORMANCE STANDARDS USED IN TESTING FOR NON-HVHZ LOCATIONS WERE AAMA/WDMA/CSA
101/I.S.2/A440-11, ASTM E1886-13a, AND ASTM E1996-14a.
3. ADEQUACY OF THE EXISTING STRUCTURAL CONCRETE / MASONRY AND 2X FRAMING FRAMING SUBSTRATES AS A
MAIN WIND FORCE RESISTING SYSTEM CAPABLE OF WITHSTANDING AND TRANSFERRING APPLIED PRODUCT LOADS
TO THE FOUNDATION IS THE RESPONSIBILITY OF THE LICENSED PROFESSIONAL ENGINEER OR REGISTERED
ARCHITECT ACTING AS THE DESIGN PROFESSIONAL OF RECORD FOR THE PROJECT OF INSTALLATION.
4.1X AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED AND ANCHORED TO PROPERLY TRANSFER ALL LOADS TO THE
STRUCTURE. BUCK DESIGN AND INSTALLATION IS THE RESPONSIBILITY OF THE LICENSED PROFESSIONAL
ENGINEER OR REGISTERED ARCHITECT ACTING AS THE DESIGN PROFESSIONAL OF RECORD FOR THE PROJECT OF
INSTALLATION.
5.THE PRODUCT SHOWN HEREIN WAS TESTED WITH IMPACT PROTECTIVE GLAZING SHOWN IN DETAIL A ON SHEET 2
FOR LARGE MISSILE IMPACT (SMALL MISSILE IMPACT ENVELOPED) IN THE HIGH VELOCITY HURRICANE ZONE (HVHZ).
WHEN INSTALLED IN LOCATIONS WHERE WINDBORNE DEBRIS PROTECTION REQUIREMENTS EXIST, THIS PRODUCT
DOES NOT REQUIRE OPENING PROTECTION.
6.SITE CONDITIONS NOT COVERED IN THIS PRODUCT EVALUATION DOCUMENT ARE SUBJECT TO ADDITIONAL
ENGINEERING ANALYSIS BY A LICENSED PROFESSIONAL ENGINEER OR REGISTERED ARCHITECT AS REQUIRED BY
THE AUTHORITY HAVING JURISDICTION.
7.MATERIALS
7.1.FRAME MATERIAL: EXTRUDED RIGID PVC BY VISION EXTRUSIONS LIMITED APPROVED PER CURRENT
MIAMI-DADE NOTICE OF ACCEPTANCE.
7.2.LAMINATED GLAZING INTERLAYER: EASTMAN CHEMICAL CO. VANCEVA APPROVED PER CURRENT MIAMI-DADE
NOTICE OF ACCEPTANCE.
7.3.GLASS MEETS THE REQUIREMENTS OF ASTM E1300-09a AND EXCEEDS THE DESIGN PRESSURES BELOW.
8.DESIGNATION "X" STANDS FOR OPERABLE PANEL AND '"O" STANDS FOR FIXED PANEL
9.INTERIOR AND EXTERIOR FINISHING AND PERIMETER SEALING ARE FOR ILLUSTRATIVE PURPOSES ONLY. THESE
DRAWINGS CERTIFY THE DOOR INSTALLATION ONLY. WATER PROOFING OF THE INSTALLED DOOR IS NOT PART OF
THIS INSTALLATION CERTIFICATION. WATER PROOFING SHALL BE THE RESPONSIBILITY OF THE INSTALLER.
9.1.PERIMETER AND JOINT SEALANT BY OTHERS TO BE DESIGNED IN ACCORDANCE WITH THE FBC RESIDENTIAL
AND BUILDING AND WITH FMA/AAMA/WDMA PROTOCOLS.
10.SEE SHEET 3, GENERAL NOTES 1, 2 AND 3 FOR APPROVED CONFIGURATIONS.
INSTALLATION NOTES:
1.PRODUCT ANCHORS SHALL BE AS DESIGNATED AND LOCATED AS SHOWN IN THIS PRODUCT EVALUATION DOCUMENT.
ANCHOR EMBEDMENT AND EDGE DISTANCE EXCLUDE WALL FINISHES, INCLUDING BUT NOT LIMITED TO STUCCO, FOAM,
BRICK VENEER AND SIDING.
2.SEE INSTALLATION ANCHOR SCHEDULE ON SHEET 2 FOR TYPE AND GRADE OF ANCHOR, AND/OR MANUFACTURER'S ANCHOR
SPECIFICATIONS, INCLUDING MINIMUM NOMINAL SIZE, MINIMUM EMBEDMENT INTO SUBSTRATE AND MINIMUM EDGE
DISTANCES.
2.1.EDGE DISTANCES SHALL BE MEASURED FROM CENTERLINE OF ANCHOR TO EDGE OF STRUCTURAL SUBSTRATE
EITHER TO THE INTERIOR OR EXTERIOR OF THE FENESTRATION PRODUCT.
2.2.MINIMUM EMBEDMENT SHALL BE BASED ON PENETRATION INTO MAIN WIND FORCE RESISTING SYSTEM SUBSTRATE.
2.3.ALL INSTALLATION ANCHORS SHALL BE MADE OF A CORROSION RESISTANT MATERIAL OR HAVE A CORRISION
RESISTANT COATING.
3.WOOD BUCKS SHALL HAVE BEEN PRESERVATIVE TREATED OR SHALL BE OF A DURABLE SPECIES AS DEFINED IN THE
CURRENT EDITION OF THE FLORIDA BUILDING CODE.
4.DISSIMILAR MATERIALS INCLUDING FASTENERS THAT MAY COME INTO CONTACT SHALL HAVE BEEN PROTECTED AS DEFINED
IN THE CURRENT EDITION OF THE FLORIDA BUILDING CODE.
5.INSTALLATION DETAILS
5.1.SEE SHEET 3 FOR ANCHOR LAYOUT ELEVATION OF A 4-TRACK OXXX-A-XXXO DOOR ELEVATION. OTHER ELEVATIONS
WILL BE INSTALLED SIMILARILY AS DISCUSSED ON SHEET 3 GENERAL NOTES & INSTALLATION NOTES.
5.2.SEE SHEETS 4, 5, 6 AND 7 FOR SECTION VIEWS OF SPECIFIC ANCHOR INSTALLATION DETAILS.
5.3.SEE SHEET 7 FOR GLAZING DETAILS.
6.TWO (2) INSTALLATION ANCHORS ARE REQUIRED AT EACH ANCHOR LOCATION SHOWN ON SHEET 3 AT 2-TRACK, 3-TRACK AND
4-TRACK HEAD, SILL AND JAMB EXTRUSIONS.
7.ANCHOR QUANTITIES AND SPACING / EMBEDMENT AND EDGE DISTANCE
7.1.THE NUMBER OF INSTALLATION ANCHORS IS BASED ON THE MAXIMUM END DISTANCE (ED) AND THE MAXIMUM ON
CENTER (O.C.) SPACING PLACEMENT OF ANCHORS IN ACCORDANCE WITH ELEVATION ON SHEET 3.
7.2.END DISTANCES AND O.C. SPACING LESS THAN THAT SHOWN IN THE ELEVATION ON SHEET 3 ARE ACCEPTABLE.
7.3.FOR DOOR SIZES SMALLER THAN THOSE SHOWN, ANCHOR QUANTITIES CAN BE REDUCED WHILE MAINTAINING EDGE
DISTANCE AND O.C. SPACING REQUIREMENTS.
7.4.ANCHOR QUANTITIES AND SPACING SHOWN ARE BASED ON THE LOWER OF ANCHOR SPACING USED IN TESTING OR
REQUIRED BY LOADING AT DESIGN PRESSURE.
7.5.SEE EMBEDMENT AND EDGE DISTANCE DESCRIPTION ON SHEET 2.
8.MAXIMUM ALLOWABLE SHIM THICKNESS IS 1/4 INCH. SHIM WHERE SPACE OF 1/16 INCH OR GREATER OCCURS. SHIM(S)
SHALL BE CONSTRUCTED OF WOOD COMPOSITE, HIGH DENSITY PLASTIC OR SIMILAR LOAD BEARING MATERIAL.
9.FOR CONCRETE BLOCK APPLICATIONS DO NOT INSTALL INSTALLATION ANCHORS INTO MORTAR JOINTS.
10.INSTALLATION ANCHORS SHALL BE INSTALLED IN ACCORDANCE WITH ANCHOR MANUFACTURER'S INSTALLATION
INSTRUCTIONS AND ANCHORS SHALL NOT BE USED IN SUBSTRATES WITH STRENGTHS LESS THAN THE MINIMUM
STRENGTH SPECIFIED IN THE INSTALLATION ANCHOR SCHEDULE ON SHEET 2.
TABLE OF CONTENTS
SHEET SHEET DESCRIPTION
1 GENERAL NOTES, INSTALLATION NOTES, TABLE OF CONTENTS
2 ANCHOR SCHEDULE - EMBEDMENT & EDGE DISTANCE - ANCHOR INSTALL
3 4-TRACK OXXX-A-XXXO DOOR ELEVATION - ANCHOR LAYOUT
4 2, 3 AND 4-TRACK VERTICAL SECTIONS
5 4-TRACK OXXX-A-XXXO HORIZONTAL CROSS SECTION
6 3-TRACK OXX-A-XXO HORIZONTAL CROSS SECTION
7 2-TRACK OX-A-XO HORIZONTAL CROSS SECTION - GLAZING DETAIL
8 & 9 BILL OR MATERIALS
PERFORMANCE RATING
CONFIGURATION
(SEE GENERAL
NOTE 11)
TRACKS NOTES
GLAZING
DETAIL (SEE
SHEET 7)
DESIGN
PRESSURE
(PSF)
IMPACT RATING
OXXX-A-XXXO 4 SHEET 3, GENERAL
NOTES 1.1, 2 & 3 A +/-50
LARGE MISSILE
(SMALL MISSILE
ENVELOPED)
OXX-A-XXO 3 SHEET 3, GENERAL
NOTES 1.2, 2 & 3 A +/-50
OX-A-XO 2 SHEET 3, GENERAL
NOTES 1.3, 2 & 3 A +/-50
O-A-XO
OX-A-O 2 SHEET 3, GENERAL
NOTES 1.4, 1.5, 2 & 3 A +/-50 GENERAL NOTES, INSTALLATION NOTES & TABLE OF CONTENTS1
BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJAFRAME ANCHORAGE MINIMUM EMBEDMENT AND EDGE DISTANCE
THROUGH-FRAME INSTALLATION
APPLICABLE TO HEAD, SILL (SHOWN) AND JAMBS (SHOWN)
WOOD AND CONCRETE SCREW
FRAME ANCHORAGE REQUIREMENTS
(NOTE 5 FROM ANCHOR SCHEDULE TABLE ABOVE)
THROUGH-FRAME INSTALLATION
APPLICABLE TO HEAD, SILL (SHOWN) AND JAMBS
–
–
–
– ANCHOR SCHEDULE - EMBEDMENT & EDGE DISTANCE - ANCHOR INSTALL2
SERIES 9700 SLIDING GLASS DOOR - OXXX-A-XXXO, 4-TRACK SYSTEM (SHOWN)
SIMILAR ARRANGEMENT FOR 3 AND 2 TRACK CONFIGURATIONS LISTED BELOW
EXTERIOR ELEVATION
B
5*
A
4
GENERAL NOTES:
1.APPROVED DOOR CONFIGURATIONS INCLUDE THE FOLLOWING.
1.1.OXXX-A-XXXO, 4-TRACK
1.1.1.ELEVATION SHOWN ABOVE.
1.1.2.SECTION VIEWS ON SHEETS 4 AND 5.
1.2.OXX-A-XXO, 3-TRACK
1.2.1.ELEVATION SIMILAR TO ABOVE.
1.2.2.SECTION VIEWS ON SHEETS 4 AND 6.
1.3.OX-A-XO, 2-TRACK
1.3.1.ELEVATION SIMILAR TO ABOVE.
1.3.2.SECTION VIEWS ON SHEETS 4 AND 7.
1.4.O-A-XO, 2-TRACK
1.4.1.ELEVATION SIMILAR TO ABOVE.
1.4.2.VERTICAL SECTION VIEW ON SHEET 4. HORIZONTAL SECTION VIEW
INSTALLATION SIMILAR TO THAT SHOWN ON SHEET 7.
1.5.OX-A-O, 2-TRACK
1.5.1.ELEVATION SIMILAR TO ABOVE.
1.5.2.VERTICAL SECTION VIEW ON SHEET 4. HORIZONTAL SECTION VIEW
INSTALLATION SIMILAR TO THAT SHOWN ON SHEET 7.
2.ANY STILE CONFIGURATION SHOWN IN HORIZONTAL SECTION VIEWS ON
SHEETS 5, 6 AND 7 ARE ALLOWED.
3.MAXIMUM FRAME AND PANEL SIZES
3.1.MAXIMUM FRAME SIZE IS 383.5" X 95.5"
3.2.MAXIMUM PANEL SIZE IS 51.55" X 92.75"
3.3.MAXIMUM PANEL DAYLIGHT OPENING (DLO) IS 40.625" X 81.875"
* SECTION B/5, 4-TRACK 8-PANEL SECTION (ELEVATION SHOWN)
SECTION B/6, 3-TRACK 6-PANEL SECTION
SECTION B/7, 2-TRACK 4-PANEL SECTION
B
6*
B
7*
INSTALLATION NOTES:
1.ANCHOR SPACING LOCATION TOLERANCES
1.1.ON CENTER (O.C.) SPACING ANCHOR LOCATION
TOLERANCE IS +/- 1".
1.2.EDGE ANCHORS ARE 3" MAXIMUM AS SHOWN.
1.3.CONCRETE ANCHORS SHALL NOT BE SPACED LESS
THAN 3" O.C. REGARDLESS OF STATED TOLERANCES.
2.ANCHOR QUANTITY AND SPACING
2.1.HEAD AND SILL
2.1.1.ANCHORS ARE QUANTITY THIRTY SIX (36) WITH
MAXIMUM 11" ON CENTER (O.C.) SPACING.
2.1.2.EDGE ANCHORS ARE 3" MAXIMUM AS SHOWN.
2.1.3.ANCHOR QUANTITIES CAN BE REDUCED AS
REQUIRED FOR SMALLER FRAMES AS LONG AS
THE EDGE DISTANCE AND O.C. SPACING
REQUIREMENTS ARE MET.
2.2.JAMBS
2.2.1.ANCHORS ARE QUANTITY TEN (10) WITH
MAXIMUM 11" ON CENTER (O.C.) SPACING.
2.2.2.EDGE ANCHORS ARE 3" MAXIMUM AS SHOWN.
2.2.3.ANCHOR QUANTITIES CAN BE REDUCED AS
REQUIRED FOR SMALLER FRAMES AS LONG AS
THE EDGE DISTANCE AND O.C. SPACING
REQUIREMENTS ARE MET.
SILL ANCHORAGE SAME AS HEADER
Max. Frame Size: 383.5" x 95.5"
Max. Panel Size: 51.5" x 92.7"
Max. Daylight Opening Size: 40.63" x 81.88"BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJA4-TRACK OXXX-A-XXXO DOOR ELEVATION - ANCHOR LAYOUT3
SERIES 9700 SLIDING GLASS DOOR
APPLICABLE TO 2-TRACK, 3-TRACK AND 4-TRACK DOOR CONFIGURATIONS.
VERTICAL CROSS SECTIONS
A
4
INTERIOREXTERIOR EXTERIOR EXTERIORINTERIOR INTERIOR
SEE
NOTE 1
BELOW.
SEE
NOTE 1
BELOW.
SEE
NOTE 1
BELOW.
SEE
NOTE1
BELOW.
SEE
NOTE 1
BELOW.
SEE
NOTE 1
BELOW.
FRAME WIDTH 5.90"FRAME WIDTH 8.28"FRAME WIDTH 10.66"
FRAME WIDTH FOR 2-TRACK, 3-TRACK AND 4-TRACK
SILL SHOWN. APPLICABLE TO HEAD AND JAMBS BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJA2, 3, 4-TRACK VERTICAL SECTIONS4
BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJASERIES 9700 SLIDING GLASS DOOR
APPLICABLE 4-TRACK OXX-A-XXO DOOR CONFIGURATION
HORIZONTAL CROSS SECTIONS
B
5
INTERIOR
EXTERIOR
SEE
NOTE 1
BELOW.
SEE
NOTE 1
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
INTERIOR
EXTERIOR
SEE
NOTE 2
BELOW.4-TRACK OXXX-A-XXXO HORIZONTAL CROSS SECTION5
BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJASEE
NOTE 1
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 1
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SERIES 9700 SLIDING GLASS DOOR
APPLICABLE 3-TRACK OXX-A-XXO DOOR CONFIGURATION
HORIZONTAL CROSS SECTIONS
B
6
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR 3-TRACK OXX-A-XXO HORIZONTAL CROSS SECTION6
BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJASERIES 9700 SLIDING GLASS DOOR
APPLICABLE 2-TRACK OX-A-XO DOOR CONFIGURATION
HORIZONTAL CROSS SECTIONS
B
7
SEE
NOTE 1
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 1
BELOW.
SEE
NOTE 2
BELOW.
SEE
NOTE 2
BELOW.
EXTERIOR
EXTERIOR
INTERIOR
INTERIOR
GLAZING DETAIL A
LAMINATED IGU
INTERIOR GLAZED WITH DOW 995 BACK-BEDDING
EXTERIOR INTERIOR 2-TRACK OX-A-XO HORIZONTAL CROSS SECTION - GLAZING DETAIL7
BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJABILL OF MATERIALS8
BYDATE9OF8/2/19DESCRIPTIONREVTITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:Robert J. Amoruso, P.E.
Florida P.E. No. 49752 PTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comRJASHW0003SHWINCO ARCHITECTURAL PRODUCTS, LLC171 JET SERVICES WAYDOTHAN, AL 36303SERIES 9700 VINYL SLIDING GLASS DOOR - HVHZPROJECT # 420-0402ANONEAUPDATE TO THE CURRENTEDITION FBC9/3/20RJABILL OF MATERIALS9