HomeMy WebLinkAboutGENERAL INFORMATION SECTION AST. LUCIE WORKS
Section A (General Information)
Master Permit No.
Contractors Name: Total Home Roofing
Job Address._ 5, (e t "L(I rfji �
License #
ROOF CATEGORY
Process No.
CCC 1330489
Slope ❑ Mechanically Fastened Tile ❑ Mortar/Adhesive Set Tiles
GWISRMaltic Shingles ❑Metal Panel/Shingles Mood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE.
❑ New roof ❑ Repair ❑ Maintenance M Reroofing ❑ Recovering
. ROOF SYSTEM INFORMATION �'[J
Low Slope Roof Area (SF) �� Steep Sloped Roof Area (SF) Total (SF)
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains. Include
dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
8/30/2021
37408_41312_1.jpg(512x384)
----------------------
:10 SPp4
n:rn
(204) 0
22
https://w.pasle.org/ImagaSketches/sketch/37/37408_41312_1.jpg 1/1
ST. LUCIE WORKS
Section D (Steep Slope Roof System)
Roof System Manufacturer: Owens Corning
Notice of Acceptance Number:
FL10674-R 16
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1:-74 one 2e: -pone 2n'108 Zone 2r-108 Zone 3e 108 one 3r:-128
Deck Tom: Wood
Type Underlayment
Roof Slope:
[2 Insulation: NIA
ire Barrier: INIA
[=Ailatllon Fastener Type & Spacing: � Q(' Ring Shank Nails
Adhesive Type: NIA
Type Cap Sheet: NIA I
Mean Roof Height: 15' Roof Covering Asphalt Shingles
Type & Sipe Drip 3" X 3" Galy Alum
Edge: _
ST. LUCIE
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component is not used, identify as "NA")
System Manufacturer: Certalnteed
Product Approval No.: FL2533-R24
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1': -34.6 Zone 1-60•3Zone 2: Zone 1-108.4
Max. Design Pressure, from the specific product approval
system: -127.5
Deck:
Type: Wood
Gauge Thickness: 1 /8"
Slope:
Anchor/Base Sheet & No. df Ply(
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s): FjmntjaStlC
Base Sheet Fastener/Bonding Material:
SA
Ply Sheet(s)' & No. of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply: Flintlastic
Top Ply Fastener/Bonding Material:
i
SA
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—"
oc @ Lap, # Rows
@ "ac
Zone 1:—"
oc @ Lap, # Rows
@ "0
Zone 2:_.._."
oc @ Lap, # Rows
@ "(
Zone 3:—"
oc @ Lap, # Rows
@ "o
Number of Fasteners Per Insulation Board:
Zone 1': Zone 1:—Zone 2: Zone 3
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc.
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16..
Flintlastic
Flintlastic
FT.
Parapet
Height
FT.
15,
Mean
Roof
Drip Edge: 3" X 3" Galy Alum Height