HomeMy WebLinkAboutNotice of AcceptanceFile Co' y
MIAMI•DiADE
a MIAMI-DARE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION RECEIVED Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) Lp 02
�, 2nt www•miamidadegov/economy
TAMKO Building Products LLC St. Lucie ;County
220 West 41 Street Permitting
Joplin, MO 64801
SCOPE:
i
This NOA is being issued under the applicable rules and regulations governing the use of; construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section,
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke,i modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: TAMKO Roof Shingles
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise�. inoted hereiri
i
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
I
TERMINATION of this NOA will occur after the expiration date or if there has been! a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure toy comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County,
expiration date may be displayed in advertising literature. If any portion of the NOA is
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manu:
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises and renews NOA No.19-1107.04 and consists of pages 1 through 8.
The submitted documentation was reviewed by Freddy Semino
and followed by the
then it shall be done
or its distributors and
NOA No.: 20-0701.02
Expiration Date: 12/01/25
Approval Date: 11/05/20
Page 1 of 7
ROOFING ASSEMBLY APPROVAL
Catesorv: Roofing
Sub -Category: Asphalt Shingles
Materials: Laminate
Deck Type: Wood
SCOPE
This approves TAMKO's Heritage, Heritage Woodgate, Heritage Premium, and Heritage Proline Titan XT
asphalt shingles, manufactured by TAMKO Building Products LLC, as described in this otice of Acceptance and
designed to comply with the Florida Building Code High Velocity Hurricane Zones.
i
PRODUCT DESCRIPTION
Product Dimensions Test Product Description
Specifications
Heritage
13 '/4' x 39 3/s"
TAS 110
j Dimensional
asphalt shingle.
Manufacturing Location # 1, 2, 3
Heritage Woodgate
13 ' ' x 39 3/8"
TAS 110
Dimensional
asphalt shingle.
Manufacturing Location # 1,3
Heritage Premium
13 '/4' x 39 3/8"
TAS 110
Dimensional
asphalt shingle.
Manufacturing Location # 1, 2, 3
i
Heritage Proline Titan XT
Manufacturing Location # 3, 4
13 '/4' x 39 3/g"
TAS 110
Dimensional
asphalt shingle.
MANUFACTURING LOCATIONS
I
1. Dallas, TX
2. Tuscaloosa, AL
3. Frederick, MD
i
4. Phillipsburg, KS
i
I
I
i
I
i
i
I !
NOA No.: 20-0701.02
Expiration Date: 12/01/25
Approval Date: 11/05/20
i Page 2 of 7
tit '
EVIDENCE SUBMITTED
Test Agency
Underwriters Laboratories, Inc.
PRI Asphalt Technologies, Inc.
PRI Construction Materials Technologies LLC
Test Identifier
Test Name/Repo:
TAS 107 & UL 790
04CA44252
ASTM D3462
02NK33813
ASTM D 3462 & TAS 107 j
R2919 Letter
ASTM D3462
4789110543
TAS 107
ASTM E 108
ASTM D3161, Class F
4787043752
ASTM D 3462
4789650787
R 2919
Letter
ASTM D 3462
4789682154
i
TAS 100
TAP-129-
02-01
TAS 100
TAP-130-02-01
TAS 100
TAP-131-02-01
TAS 100
TAP-3031-02-01
TAS 100
TAP-307-02-01
TAS 100
TAP-317-02-01
Date
02/25/05
09/23/02
03/10/11
08/26/14
02/19/15
08/26/14
10/20/15
10/12/20
10/15/20
10/15/20
05/26/05
05/26/05
05/26/05
12/12/14
02/10/15
09/02/15
NOA No.: 20-0701.02
CM1AMUWADECO=QNW Expiration Date: 12/01/25
Approval Date: 11/05/20
Page 3 of 7
f
U IITATIONS
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product. i
2. Shingles shall not be installed on roof mean heights in excess of 33 ftl i
3. All products listed herein shall have a quality assurance audit in accordance with thIl Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
INSTALLATION
1. Shingles shall be installed in compliance with Roofing Application Standard RAS li 15.
2. Flashing shall be in accordance with Roofing Application Standard RAS 115.
3. The manufacturer shall provide clearly written application instructions.
4. Exposure and course layout shall be in compliance with Detail `A', attached.
5. Nailing shall be in compliance with Details V, attached.
LABELING
Shingles shall be permanently labeled with. the manufacturer's name and/or logo, city and state of
manufacturing facility, and the following statement: "Miami -Dade County Product! Control Approved" or with
the Miami -Dade County Product Control Seal as seen below: j
i
QML•DADE COUNTY
BUILDING PERMIT REQUIREMENTS
As required by the Building Official or the applicable Building Code iin order to properly evaluate the
installation of this system. This Notice of Acceptance on its own cannot be used toy obtain a building permit.
I
I I
i
i
I
I
i
NOA No.: 20-0701.02
MAMMADE COUNTY Expiration Date: 12/01/25
"' • ' Approval Date: 11/05/20
Page 4 of 7
I
i
i
6-1/8"
DETAIL A
PROLINE TITAN XT
All dimensions are in inches.
SSE
1 ST COURSE
DETAIL B
LTE, HERITAGE
FIG.1 FASTENING PATTER
All dimensions are in inches
1" 7'/z" 7'/2" \ 7 3/s" 7'/z" 7'/z" I 1" 13-1/4"
�I�>I�I�� �I1IH
______________ ______________ --------------
_____________If -------------
;
5-5/8"
NOA No.: 20-0701.02
Expiration Date: 12/01/25
Approval Date: 11/05/20
Page 5 of 7
IT
dh
M
L
PAINT
DETAIL B (CONTINUED)
FIG. 2 ALTERNATE FASTENING PATTED
12-1/2" 12-1
FASTENERS
39-3/8"
i
HERITAGE SHINGLE
(TUSCALOOSA, AL)
FIG. 3 ALTERNATE FASTENING PATTERN
HORIZONTAL NAIL SPACING IN ACCORDANCE WITH FIG. I OR FIG. 2.
VERTICAL NAIL SPACING ALLOWED ANYWHERE WITHIN NAIL ZONE.
ACCEPTABLE
FASTENER LOCATION
PREFERRED
FASTENER
LOCATION
® Common Bond
ZONE`
NOA No.: 20-0701.02
MIAMMWE COUNW Expiration Date: 12/01/25
Approval Date: 11/05/20
Page 6 of 7
i
HERITAGE PROLINE TITAN XT SHINGLES
FIG. 4 ALTERNATE. FASTENING PATTERN
HORIZONTAL NAIL SPACING IN ACCORDANCE WITH FIG.1 OR T1 IG. 2.
VERTICAL NAIL SPACING ALLOWED ANYWHERE WITHIN NAIL ZONE.
\ jNai l Zone
;T
00 80 5-5/8, *Paint Lines
Ex'I osure
i
` 3J3/8' i
Acceptable Fastener Location
Preferred Fastener Location
END OF THIS ACCEPTANCE
NOA No.: 20-0701.02
Expiration Date: 12/01/25
Approval Date: 11/05/20
Page 7 of 7