HomeMy WebLinkAboutInstallation Guidelines for 60Hz Air-Cooled Generators�P« �. 3
ST.LUCIE COUNTY
G PLAN REVIEW
!g ap BLDG:
m0
DATE_:
�3
ELE
�* jjjL§L
DATEJ'���/
PLUMB: -
DATE:
MECH;
DATE:
` ley`
FILE COPY
.r
�v
�?
R
�r,
��
�;
' �
� s�
-._� a.=_ - z=� s — V_
Total Square Footage of Residence
Square Footage@ 3 Watts Per Ft2
1950
managed ? All Appliances,Motors, and Low Power Factor Loads:
Range
7680
Diswasher
1680
Washer
1200
Microwave
1500
Refrigerator -
1200
Tankless water heater
200
Sump Pump
750
Water Pump
1800
X Dryer
5000
X Pool Pump
1800
Appliance and Other Loads
total load from steps 1 & 2
1st 10 KW @ 100
Remainder @ 40%
Total General Load
managed? System#
x System 1
Discounted Load:
Total Calculated Load :
Cooling
A/C & Heating
Load Management Summary:
( At 100% of Load Value)
Total Generator Load:
22810
28,660
10,000
7,464
17464
load heat load
3,813 10,000
6500
Watts 23964
Amps: 99.85
Total Managed Load:
17,100
14,744
( Load on Generator with discounted
managed load values removed from
total load)
345
113.81
vrROLvnxNG��tttvKa.swrvuun 13RRATED PLUG (FIELD SUPPLIED) F
uuzrSRIJTDOWNSYVITCH
ly-1r Ron
-WIRELEMGi'rrit�
SS 6iODULE
:3W NPT (14.18-24" 05
REQU7R® FUEL PRESSURE: NATURALGAS : &S-r WATER COLUMN Well
LIQUID PROPANE (VAPOR) :18-1T WATER COLUMN
Lt
733 - -
(28.81
Ira v
218 ._... ....._ REAR VIEW �- 14 �yC ,ta TRM tl'IMb • t set
LEFT SIDE VIEW
COMPACTED SOIL
RIGHT SIDE VIEW
50 Installation Guidelines for 60 Hz Air -Cooled, Generators
Section 2 General Information and Setup
Figure 2-1. Features and Controls
Know Your Smart Management Module and
Carton Contents
Priority Dial (A) — Sets module priority.
NOTE: PRIORITY MUST BE DIFFERENT for each module
in an installation. Priority sets the order in which loads recover
from a load shed event. Recovery time from a load shed event
is five minutes for Priority 1. Each priority after Priority 1 waits
an additional 15 seconds after the initial recovery time. See
Table 1.
Lockout Switch (B) — Prevents load from operating when sys-
tem is operating under generator power. See Table 2.
NOTE: Recovery time is based on priority dial settings. See
Table 1.
Test Button (C) — Disables contactor output for a specified
time_
LED (D) — Provides module status. See Table 3_
Contactor (E) — Controlled by a smart controller in module.
Contactor remains CLOSED until generator power is required.
Upon generator activation, controller moves to OPEN to handle
overload conditions.
NOTE: The contactor is also opened during lockout switch
ACTIVE state.
Mounting Holes (F) — Internal enclosure mounting holes pro-
vide clean and sturdy mounting.
Priority Decal (G) — Provided for recording priority of each
module in installation. Should be installed on electrical panel.
Owner'slInstallation Manual for SMM
Table 1. Priority Dial Settings
Priority
Recovery Time
1
5 minutes
2
5 minutes 15 seconds
3
5 minutes 30 seconds
4
5 minutes 45 seconds
5
6 minutes
6
6 minutes 15 seconds
7
6 minutes 30 seconds
8
6 minutes 45 seconds
g
Not Used
0
Not Used
Section 3 Installation, Tests and Troubleshooting►
Electrical Specifications
Input Voltage
240 VAC
Current Rating
50A resistive, 40A inductive
Locked Rotor Amp Rating
240A
Motor Rating
3HP
Contactor Coil Voltage
1240 VAC
Enclosure Specifications
UL Rating I Type 3R
Temperature -30 to 50 deg C (-22 to 122 deg F)
Remove Contents from Carton
1. Open carton.
2. Remove and verify carton contents.
3. Retain carton for mounting template.
Carton Contents:
• Smart Management Module (SMM)
• Priority decal
• Owner/Installation manual
4. Contact the place of purchase with the unit model num-
ber for any missing carton contents.
5. Record date of purchase on front cover of this manual.
Tools Needed For Installation
• Power drill and suitable drill bit
• Phillips and flat head screwdrivers
• Mounting screws or wall anchors
• Electrical materials
Mounting Instructions
The recommended installation is near the electrical panel or
appliance/load. The enclosure has a UL type 3R rating and can
be mounted indoors or outdoors. It provides a degree of
protection against rain and sleet and is undamaged by the
formation of ice on the enclosure.
)1A Electrocution. Turn utility and emergency
power supplies to OFF before connecting power
source and load lines. Failure to do so will result
in death or serious injury. (000116)
1. Turn OFF both UTILITY (NORMAL) and EMERGENCY
(STANDBY) power supplies.
2. Choose mounting location (near electrical panel,
appliance or load to be managed).
3. Use a flat head screwdriver to remove appropriate
knockouts from module enclosure for wiring. See A in
Figure 3-1.
NOTE: If outdoor installation is chosen, bottom knockouts
must be used to meet NEMA 3R rating and protect against
water ingress.
Owner's/installation Manual for SMM
4. Hold SMM enclosure against mounting surface with
arrows pointing up, and mark or drill four mounting holes.
See B in Figure 3-1 for arrows.
S. Install SMM enclosure to mounting surface using appro-
priate mounting screws or wall anchors.
000138
Figure 3 -1. Knockouts and UP Arrows
�Wl 01
D1
O O o
000107
Figure 3 -2. Mounting Dimensions
Height (in/mm)
H1
6.171156.8
H2
2.36/60
Width (in/mm)
W1
7.061179.4
W2
4.72/120
Depth (in/mm)
D1
3.7/94