The URL can be used to link to this page

Home My WebLink AboutNOA STEEL PANELMIAMI• MMD MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786)315-2590 F (786)315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.eov/economy Coastal Metal Roofing Sales, LLC 10877 NW 33 Street Doral, FL. 33172 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Coastal ML150 24Ga. Steel Panel over Plywood deck LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA consists of pages 1 through 6. The submitted documentation was reviewed by Alex Tigera. NOA No.: 21-0422.02 Expiration Date: 06/17/26 Approval Date: 06/17/21 Page 1 of 6 ROOFING SYSTEM APPROVAL: Category Sub -Category: Material: Deck Type: Maximum Desien Pressure Roofing Metal, Panels (Non -Structural) Steel Wood —176.00 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: Product Dimensions Coastal ML150 24Ga. Length: various Steel Panel Height: 1-1/2" Width: 16" Thickness 24 ga Min. Yield Strength: 62.6 ksi. Fixed Clip Length:2" Height: 1-5/8" Width: 1-1/4" Thickness: 24ga EVIDENCE SUBMITTED: Test Agency Intertek PRI Construction Materials Technologies Test Specifications TAS 110 Test Identifier L2072.07-450-18 RO L2072-01-450-18 RO L2072.02-450-18 RO 1272T0005 1272T0002 Product Description Corrosion resistant, galvanized steel or galvalume standing seam metal panel. One piece panel clip used for the field conditions of DMC 150 SS panel assembly System B. Test Name/Report Date ASTM E 2140 03/31/21 TAS 125 03/16/21 TAS 100 03/16/21 ASTM G 155 09/24/19 ASTM B It 7 09/11/19 NOA No.: 21-0422.02 Expiration Date: 06/17/26 Approval Date: 06/17/21 Page 2 of 6 APPROVED ASSEMBLIES: System A: Coastal ML 150 24Ga. Steel Panel 16" wide Panel Deck Type: Wood, Non -insulated Deck Description: New Construction 19/32" or greater plywood or wood plank. Slope Range: l" : 12" or greater (see note below) Maximum Uplift See Maximum Design Pressures below Pressure: Deck Attachment: In accordance with applicable Building Code, but in no case shall it be less than 8d annular ring shank nails spaced 6" o.c. In reroofing, where the deck is less than 19/32" thick (Minimum "/32") The above attachment method must be in addition to existing attachment. Underlayment: Minimum underlayment shall be an ASTM D 226 Type Il installed with a minimum 4" side - lap and 6" end -laps. Underlayment shall be fastened with corrosion resistant tin -caps and 12 gauge 1 ""/4" annular ring -shank nails, spaced 6" o.c. at all laps and two staggered rows 12" o.c. in the field of the roll or any approved underlayment having a current NOA. Fire Barrier Board: Any approved fire barrier having a current NOA. Refer to a current fire directory listing for fire ratings of this roofing system assembly as well as the location of the fire barrier within the assembly. See Limitation # 1. Valleys: Valley construction shall be in compliance with Roofing Application Standard RAS 133 and with the current published installation instructions and details in Coastal Metal Sales Roofing, LLC.'s Installation Manual. Metal Panels and Install the "Coastal ML150 24Ga. Steel Panel 16" wide Panel" including flashing Accessories: penetrations, valleys, end laps and accessories in compliance "Coastal Metal Sales Roofing, LLC.'s" Current, published installation instructions and in compliance with the minimum requirements detailed in Roofing Application Standard RAS 133. Panels shall be secured along the male rib with approved clips fastened with two corrosion resistant #10 pancake head fasteners of sufficient length to penetrate through the sheathing a minimum of 3/16'. The panel clips shall be located at the maximum spacing listed in Table A below. Note: For slopes of 1" : 12" up to but not including 2" : 12", a continuous bead of a Miami Dade Approved Sealant must be applied along the entire Male rib before attaching the adjacent panel. For slopes of 2" : 12" and greater, the sealant is not required. TABLE A MAXIMUM DESIGN PRESSURES Roof Areas Field Perimeter and Corner' Maximum Design Pressures 46 psf. —176 psf. Maximum Clip Spacing 24" o.c. 6" o.c. Mechanical Seam 900 900 1. Extrapolation shall not be allowed NOA No.: 21-0422.02 Expiration Date: 06/17/26 Approval Date: 06/17/21 Page 3 of 6 LIMITATIONS 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. The maximum designed pressure listed herein shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). 3. Panels may be rolls formed in continuous lengths from eave to ridge. Maximum lengths shall be as described in Roofing Application Standard RAS 133 4. All panels shall be permanently labeled with the manufacturer's name and/or logo, city and state, and the following statement: "Miami -Dade County Product Control Approved" or with the Miami -Dade County Product Control Seal as seen below. All clips shall be permanently labeled with the manufacturer's name and/or logo, and/or model. MIAMI•DADE COUNTY �rj...• ymi 5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. NOA No.: 21-0422.02 Expiration Date; 06/17/26 Approval Date: 06/17/21 Page 4 of 6 PROFILE DRAWINGS 16" COVERAGE COASTAL ML150 24GA. STEEL PANEL NOA No.: 21-0422.02 Expiration Date: 06/17/26 Approval Date: 06/17/21 Page 5 of 6 0-4375 0.313 i.825 j�-0.913� ALL DIMENSIONS ARE DECIMAL INCHES TOLERANCE: 0.030t 2.00D--{ FIXED CLIP END OF THIS ACCEPTANCE NOA No.: 21-0422.02 M64MMADE COUNTY Expiration Date: 06/17/26 Im Approval Date: 06/17/21 Page 6 of 6