Loading...
HomeMy WebLinkAboutAPPROVED 9200 SGD(1) NOA No. 20-0901.06 Expiration Da te: February 13, 2023 Approval Date: December 03, 20 20 Page 1 MIAMI –DADE COUNTY, FLORIDA PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315–2590 F (786) 315–2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy Lawson Industries, Inc. 8501 NW 90th Street Medley, FL 33166 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami–Dade County RER–Product Control Section to be used in Miami–Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami–Dade County Product Control Section (In Miami–Dade County) and/ or the AHJ (in areas other than Miami–Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or m aterial fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revok e this acceptance, if it is determined by Miami–Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Series “SDG–9200" Aluminum Sliding Glass Door (Steel reinforced)– L.M.I. APPROVAL DOCUMENT: Drawing No. L9200–1201 Rev D, titled “Series SGD–9200 Aluminum Sliding Glass Door (LMI)”, sheets 0 1 through 14 of 14, prepared by manufacture, dated 09/25/12 and last revised on AUG 03, 2020, signed and sealed by Thomas J. Soto, P. E., bearing the Miami–Dade County Product Control Section Revision stamp with the Notice of Acceptance number and Expiration date by the Miami–Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant 1. See Design Pressure (DP) Vs door size, glass type , reinforcements, sill type and configuration in sheets 2 , sheet 5 and sheet 8 . 2. See pocket installation detail in sheet 11 and notes #15 and #16 in sheet 1. 3. Applicable Egress requirements to be reviewed by AHJ. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, se ri es, and following statement: "Miami–Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorseme nt of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami–Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA #17-1212 .0 5 and consists of this page 1 and evidence pages E–1, E–2, E–3, E-4 and E–5 , as well as approval document mentioned above. The submitted documentation was reviewed by Ishaq I. Chanda , P. E. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20–0901.0 6 Expiration Date: February 13, 2023 Approval Date: December 03, 20 20 E – 1 Lawson Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. Evidence submitted in previous files A. DRAWINGS 1. Manufacturer's die drawings and sections. (Submitted under previous NOA No. 12–1204.12) 2. Drawing No. L9200–1201, titled “Series SGD–9200 Aluminum Sliding Glass Door (LMI)”, sheets 01 through 14 of 14, prepared by manufacture, dated 09/25/12, with the latest revision “B”, dated 04/15/1 5, signed and sealed by Thomas J. Soto, P. E. B. TESTS 1. Te st reports on: 1) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 along with marked –up drawings and installation diagram of an Aluminum SGD, prepared by Hurricane Engineering & Testing, I nc., Test Report s No.’s HETI–11– 3269, dated 05/16/11, HETI–11–3292, dated 10/20/11, HETI–11–3274, dated 10/20/11, HETI–11–3329, dated 01/16/12, HETI–12–4040, dated 10/12/12, HETI–12–4051, dated 06/13/12, HE TI–12–4053 and HETI–12–4064, dated 09/24/12, all signed and sealed by Rafael E. Droz–Seda, P. E. (Submitted under previous NOA No. 12–1204.12) 2. Test reports on: 1) Large Missile Impact Test per FBC, TAS 201–94 2) Cyclic Wind Pressure Loading per FBC, TAS 203–94 along with marked –up drawings and installation diagram of an Aluminum Sliding Glass Door, prepared by Hurricane Engineering & Testing, Inc., Test Report s No.’s HETI– 11–3270, dated 05/16/11, HETI–11–3275, dated 10/20/11, HETI–11–3307, dated 10/03/11, HETI–11–3314, dated 10/20/11, HETI–11–3330, d at ed 01/16/12, HETI–12– 4052, dated 07/10/12, HETI–12–4054 and HETI–12–4065, dated 09/24/12, all signed and sealed by Rafael E. Droz–Seda, P. E. (Submitted under previous NOA No. 12–1204.12) 3. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 2) Large Missile Impact Test per FBC, TAS 201–94 3) Cyclic Wind Pressure Loading per FBC, TAS 203–94 along with marked –up drawings and installation diagram of an Aluminum Sliding Glass Door, prepared by Hurricane Engineering & Testing, Inc., Test Report No. HETI–12– 4041, dated 10/12/12, signed and sealed by Rafael E. Droz–Seda, P. E. (Submitted under previous NOA No. 12–1204.12) 4. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3) Water Resistance Test, per FBC, TAS 202–94 along with marked –up drawings and installation diagram of an Aluminum Sliding Glass Door, prepared by Hurricane Engineering & Testing, Inc., Test Reports No.’s HETI–11– 3291, dated 07/15/11 and HETI–11–3292, d ated 10/20/11, both signed and sealed by Rafael E. Droz–Seda, P. E. (Submitted under previous NOA No. 12–1204.12) Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20–0901.0 6 Expiration Date: February 13, 2023 Approval Date: December 03, 20 20 E – 2 Lawson Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED B. TESTS (CONTINUED) 5. Test reports on: 1) Air Infiltration Test , per FBC, TA S 202–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3) Water Resistance Test, per FBC, TAS 202–94 4) Large Missile Impact Test per FBC, TAS 201–94 5) Cyclic Wind Pressure Loading per FBC, TAS 203–94 6) Forced Entry Test, Type “C” sliding door, Grade 10, per FBC 2411.3.2.1, TAS 202–94 and per ASTM F 842–04 along with marked –up drawings and installation diagram of an Aluminum Sliding Glass Door, prepared by Hurricane Engineering & Testing, Inc., Test Report No. HETI–11– 3313, dated 10/20/11, signed and sealed by Rafael E. Droz–Seda, P. E. (Submitted under previous NOA No. 12–1204.12) 6. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3) Water Resistance Test, per FBC, TAS 202–94 4) Large Missile Impact Test per FBC, TAS 201–94 5) Cyclic Wind Pressure Loading per FBC, TAS 203–94 6) Forced Entry Test, Type “C” sliding door, Grade 10, per FBC 2411.3.2.1, TAS 202–94 and per ASTM F 842–04 along with marked –up drawings and installation diagram of an Aluminum Sliding Glass Door, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.’s FTL– 3078, dated 01/10/02, signed and sealed by Luis Figueredo, P.E.; FTL–3525 and FTL–3572, dated 09/09/02, both signed and sealed by Joseph C. Chan, P. E.; FTL–3424, dated 04/18/02, FTL–3425, dated 04/29/02, FTL–3426, dated 04/26/02, FTL–3492, dated 06/20/02, FTL–3493, dated 06/24/02 and FTL–3516, dated 07/12/02, all signed and sealed by James G. Worth, P. E. (Submitted u nder previous NOA No. 02–1126.04) C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC, prepared by manufacture, dated 04/28/1 5, signed and sealed by Thomas J. Soto, P. E. 2. Glazing complies with ASTM E1300–04/ 09 D. QUALITY ASSURANCE 1. Miami–Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 14–0916.10 issued to Kuraray America, Inc. for their “Kuraray PVB Glass Interlayer”, expiring on 12/11/16. 2. Notice of Acceptance No. 14–0916.11 issued to Kuraray America, Inc. for their “Kuraray SentryGlas® Interlayer”, expiring on 01/14/17. 3. Notice of Acceptance No. 14–0423.15 issued to Eastman Chemical Company (MA) for their “Saflex CP – Saflex and Saflex HP Composite Glass Interlayers with PET Core” dated 06/19/1 4, expiring on 12/11/18. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20–0901.0 6 Expiration Date: February 13, 2023 Approval Date: December 03, 20 20 E – 3 Lawson Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED F. MATERIAL CERTIFICATIONS 4. Notice of Acceptance No. 14–0916.10 issued to Kuraray America, Inc. for their “Kuraray PVB Glass Interlayer”, expiring on 12/11/16. 5. Notice of Acceptance No. 14–0916.11 issued to Kuraray America, Inc. for their “Kuraray SentryGlas® Interlayer”, expiring on 01/14/17. 6. Notice of Acceptance No. 14–0423.15 issued to Eastman Chemical Company (MA) for their “Saflex CP – Saflex and Saflex HP Composite Glass Interlayers with PET Core” dated 06/19/1 4, expiring on 12/11/18. 7. Notice of Acceptance No. 14–0423.16 issued to Eastman Chemical Company (MA) for their “Saflex HP Clear or Color Glass Interlayers” dated 06/19/1 4, expirin g on 04/14/18. 8. Notice of Acceptance No. 14–0423.17 issued to Eastman Chemical Company (MA) for their “Saflex Clear and Color Glass Interlayers” dated 06/19/14, expiring on 05/21/16. 9. Technical data sheet of flexible vinyl compound FPVC 7267–75 (White) & FPVC 7200– 75 (Black), published by Team Plastics. Inc./ Bayshore Vinyl Compounds, Inc. G. STATEMENTS 1. Statement letter of conformance to and complying with FBC 5th Edition (2014), issued by manufacturer, dated 09/02/14, signed and sealed by Thomas J. Sotos, P. E. 2. Statement letters of no financial interest, independence, conformance and complying with FBC–2010, issued by manufacture, dated 12/03/12, signed and sealed by Thomas J. Soto, P. E.(Submitted under previous NOA No. 12–1204.12) 3. Laboratory compliance letters for Test Reports No.’s HETI–11–3269, dated 05/16/11, HETI–11–3270, dated 05/16/11, HETI–11–3271, dated 10/20/11, HETI–11–3272, dated 10/20/11, HETI–11–3274, dated 10/20/11, HETI–11–3275, dated 10/20/11, HETI–11– 3291, dated 07/15/11, HETI–11–3292, d ated 10/20/11, HETI–11–3307, dated 10/03/11, HETI–11–3313, dated 10/20/11, HETI–11–3314, dated 10/20/11, HETI–11–3329, dated 01/16/12, HETI–11–3330, dated 01/16/12, HETI–12–4040, dated 10/12/12, HETI–12– 4041, dated 10/12/12, HETI–12–4051, dated 06/13/12, HETI–12–4052, dated 07/10/12, HETI–12–4053, dated 09/24/12, HETI–12–4054, dated 09/24/12, HETI–12–4064, dated 09/24/12, and HETI–12–4065, dated 09/24/12, all issued by Hurricane Engineering & Testing, Inc., all signed and sealed by Rafael E. Droz–Seda, P. E. (Submitted under previous NOA No. 12–1204.12) Laboratory addendum letter for Test Reports No.’s HETI–11–3269, HETI–11–3270, HETI–11–3271, HETI–11–3272,HETI–11–3274, HETI–11–3275, HETI–11–3291, HETI–11–3292, HETI–11–3307, HETI–11–3313, HETI–11–3314, HETI–11–3329, HETI–11–3330, HETI–12–4040, HETI–12–4041, HETI–12–4051, HETI–12–4052, HETI–12–4053 , HETI–12–4054, HETI–12–4064 and HETI–12–4065, dated 01/15/13, issued by Hurricane Engineering & Testing, Inc., signed and sealed by Rafael E. Droz– Seda, P. E. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20–0901.0 6 Expiration Date: February 13, 2023 Approval Date: December 03, 20 20 E – 4 Lawson Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED F. STATEMENTS (CONTINUED) 4. Laboratory addendum letter for Test Reports No.’s HETI–11–3269, HETI–11–3270, HETI–11–3271, HETI–11–3272,HETI–11–3274, HETI–11–3275, HETI–11–3291, HETI–11–3292, HET I–11–3307, HETI–11–3313, HETI–11–3314, HETI–11–3329, HETI–11–3330, HETI–12–4040, HETI–12–4041, HETI–12–4051, HETI–12–4052, HETI–12–4053 , HETI–12–4054, HETI–12–4064 and HETI–12–4065, dated 01/15/13, issued by Hurricane Engineering & Testing, Inc., signed and sealed by Rafael E. Droz– Seda, P. E.(Submitted under previous NOA No. 12–1204.12) 5. Proposal issued by Product Control, dated 03/30/12, signed by Jaime D. Gascon, P. E. 6. Proposal issued by Product Control, dated 03/13/08, signed by Ishaq Chanda, P. E. (Submitted under previous NOA No. 11–0518.03) 7. Laboratory compliance letters issued by Fenestration Testing Laboratory, Inc., for Test Reports No.’s FTL–3078, dated 01/10/02, signed and sealed by Luis Figueredo, P.E. (Submitted under previous NOA No. 02–1126.04) 8. Laboratory compliance letters issued by Fenestration Testing Laboratory, Inc., for Test Reports No.’s FTL–3525 and FTL–3572, dated 09/09/02, both signed and sealed by Joseph C. Chan, P. E.(Submitted under previous NOA No. 02–1126.04) 9. Laboratory compliance letters issued by Fenestration Testing Laboratory, Inc., for Test Reports No.’s FTL–3424, dated 04/18/02, FTL–3425, dated 04/29/02, FTL–3426, dated 04/26/02, FTL–3492, dated 06/20/02, FTL–3493, dated 06/24/02 and FTL–3516, dated 07/12/02, all signed and sealed by James G. Worth, P. E. (Submitted under previous NOA No. 02–1126.04) G. OTHER S 1. Notice of Acceptance No. 12–1204.12, issued to Lawson Industries, Inc. for their Series “SGD–9200 Aluminum Sliding Glass Door – L.M.I.”, approved on 01/31/13 and expiring on 02/13/18. 2. Evidence submitted under previous approval. A. DRAWINGS 1. Drawing No. L9200–1201 Rev C, titled “Series SGD–9200 Aluminum Sliding Glass Door (LMI)”, sheets 01 through 14 of 14, prepared by manufacture, dated 09/25/12 and last revised on NOV 21, 2017, signed and sealed by Thomas J. Soto, P. E. Note: This revision consists of editorial changes of FBC 2017 (6th Edition) code compliance. B. Test 1. None. C. CALCULATIONS 1. None D. QUALITY ASSURANCE 1. Miami Dade Department of Regulatory and Economic Resources (RER). Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20–0901.0 6 Expiration Date: February 13, 2023 Approval Date: December 03, 20 20 E – 5 Lawson Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 14-0916.11 issued to Kuraray America, Inc. (Former E.I. DuPont DE Nemours) for the “Sentry Gla ss ® clear & white interlayer”, expiring on 07/04/18. 2.Notice of Acceptance No. 16-1117.01 issued to Kuraray America., Inc. for their “Trosifol ® Ultraclear, Clear and Color PVB Glass Interlayers”, expiring on 07/08/19. 3.Notice of Acceptance No. 15–1201.11 issued to Eastman Chemical Company (MA) (former Solutia, Inc.) for the “Saflex: Saflex Clear & Color glass interlayer”, expiring on 05/21/21. F. STATEMENTS 1. Statement letter of conformance to FBC 2017 (6th Edition) and “No finan cial interest” dated 11/17/1 7, prepared by the manufacturer, signed and sealed by Thomas J. Sotos, P.E. G. OTHER 1. This NOA revises & renews#14-0908.02, expiring 02/13/2 3. 3. New Evidence submitted. A. DRAWINGS 1. Drawing No. L9200–1201 Rev D, titled “Series SGD –9200 Aluminum S lid ing Glass Door (LMI)”, sheets 01 through 14 of 14, prepared by manufacture, dated 09/25/12 and last revised on DEC 03, 2020, signed and sealed by Thomas J. Soto, P. E. Note: This revision consists of editorial changes of FBC 2020 (7th Edition) cod e compliance. B. Test 1. None. C. CALCULATIONS 1. None D. QUALITY ASSURANCE 1. Miami Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. f or t heir “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 2. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for t heir “Trosifo l® Ultraclear, C lear and Color PVB Glass Interlayers”, expiring on 07/08/24. 3. Not ice of Acceptance No. 15–1201.11 issued to Eastman Chemical Company (MA) (former Solutia, Inc.) for the “Saflex: Saflex Clear & Color glass interlayer”, expiring on 05/21/21. F. STATEMENTS 1. Statement letter of conformance to FBC 2020 (7th Edit ion) and “No financial interest” dated 08/03/20, prepared by the manufacturer, signed and sealed by Thomas J. Sotos, P.E. G. OTHER 1. This NOA revises #1 7 -1212.0 5 and updates to FBC 2020, expiring 02/13/2 3.