HomeMy WebLinkAboutNOA MIAMI-DADE COUNTY
MIAM1464bit PRODUCT CONTROL SECTION
: iMA a 11805 SW 26 Skeet, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) rtvty. aetarnidade.cmviee000mv
[GAF
Campus Drivearsippany, NJ 07054
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control
Section (In Miami Dade County) and/or the AM (in areas other than Miami Dade County) reserve the right to
have this product or material tested for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to
revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code. t
DESCRIPTION* GAF Timberline HD®, Timberline® Natural Shadow®, Timberline® NS, Timberline® American
Harvest®, Timberlines' AH Timberline® IHDZTM, Timberline® CS and Fortitude® Shingles
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change i
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT* The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done N
in its entirety.
INSPECTION* A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shalt be available for inspection at the job site at the request of the Building Official.
I
This NOA renews and revises NOA # 16-0811 . 11 and consists of pages 1 through 7.
The submitted documentation was reviewed by Freddy Sernino
NIANMADE COUNTY
=Datew
4
e 2
0
Page I of 7
ROOFING ASSEMBLY APPROVAL
Category DRoofingSub-Category:Materials:Deck Tyne:
SCOPE
This approves GAF Timberline HD®, Timberline® Natural Shadow®, Timberline NS®, Timberline American® 1
Harvest®, Timberline AH®, Timberline® HDZTM, Timberline CS® and FortitudeTM Shingles as manufactured by
GAF as described in this Notice of Acceptance.
PRODUCT DESCRIPTION
Product Dimensions Test Product Description
Specifications
GAF Timberline HD® 13 '/a" x 39 3/e' TAS 110 Fiberglass reinforced heavy weight asphalt roof
Manufacturing shingle, with a laminate profile
Locations #1, 2, 3, 4, 5, 6, 7
GAF Timberline® Natural 13 W' x 39 3/s TAS 110 Fiberglass reinforced heavy weight asphalt roof
Shadow® and Timberline® NS shingle, with a laminate profile
Manufacturing
Locations #1, 2, 3, 4, 5, 6, 7
to
GAF Timberline® American 13 1/4' x 39 3/8 TAS 110 Fiberglass reinforced heavy weight asphalt roof
Harvest® shingle, with a laminate profile
Manufacturing
Locations #2, 4 , 6, 9
GAF Timberline®AH 13 Ve ' x 39 3/a• TAS 110 Fiberglass reinforced heavy weight asphalt roof
Manufacturing shingle, with a laminate profile
Locations #2, 4, 6, 9
f/GAF Timberline® HDZ"" 131/4' x 39 3/s to TAS 110 Fiberglass reinforced heavy weight asphalt roof
Manufacturing shingle, with a laminate profile
Locations #1, 2, 3, 4, 5, 6, 7, 8, 9
GAF Fortitude® 13 '/4' x 39 3/a TAS 110 Fiberglass reinforced heavy weight asphalt roof
Manufacturing g shingle, with a laminate profile
Location #4
GAF Timberline® CS 131/4 1
9x 39 3/8 TAS 110 Fiberglass reinforced heavy weight asphalt roof
Manufacturing shingle, with a laminate profile
Location #9
MIAMI•DADE COUNTY
NOA No.: 19=0312.04
e i Expiration Date: 02/21/22
Approval Date: 01/09/20
Page 2 of 7
MANUFACTURING LOCATION
1. Tampa, FL
2. Michigan City, IN
3. Baltimore, MD
4. Myerstown, PA
5. Ennis, TX fi
6. Tuscaloosa, AL
7. Dallas, TX
8. Shafter, CA
9. Fontana, CA
k
g
NOA No.: 19-0312.04
MIAMICADE CO Expiration Date: 02/21/22
a e
Approval Date: 01l09/20
Page 3 of 7
EVIDENCE SUBMITTED
Test gma Test Identifier Test Flame/Report Date
Underwriters Laboratories, LLC ASTM D3462 4788932264 12/13/19
Underwriters Laboratories, LLC ASTM D3462 4788717529 01/31/19
Underwriters Laboratories, LLC ASTM D3462 4787344101 07/25/16
Underwriters Laboratories, Inc. ASTM D3462 I ICA49924 10/22/11
Underwriters Laboratories, Inc ASTM D3462 IOCA21994 04/22/11
Underwriters Laboratories, Inc ASTM D3462 I OCA28717 07/26/11
Underwriters Laboratories, Inc. ASTM D3462 05CA47541 11/10/06 l
Underwriters Laboratories, Inc. ASTM D3462 06CA31580 11/30/06
PRI Asphalt Technologies, Inc. ASTM D3462 GAF401-02-02 11/02/05 "
Underwriters Laboratories, Inc. ASTM D3462 06NK05159 08/09/06
PRI Asphalt Technologies, Inc. ASTM D3462 GAF-098-02-02 11/08/05
Underwriters Laboratories, Inc. ASTM D3462 02NK41809 08/11/02
Underwriters Laboratories, Ino.Center for ASTM D3462ASTM 03NK26444257989 10/ 17/03
Applied Engineering D3462 05/13/97
Underwriters Laboratories, LLC TAS 107 4789225984 i l/l/19
Underwriters Laboratories, LLC TAS 107 4788717529 01/31/19
Underwriters Laboratories, Inc. TAS 107 OINK45803 04/13/94
Underwriters Laboratories, Inc. TAS 107 06NK05159 08/09/06
Underwriters Laboratories, Inc. TAS 107 04NK04273 02/20/04
Underwriters Laboratories, Inc. TAS 107 05CA42840 11/11/05 t
Underwriters Laboratories, Inc. TAS 107 02NK41811 11/ 11/02
Underwriters Laboratories, Inc. TAS 107 03CA35209 10/17/03
Underwriters Laboratories, Inc. TAS 107 04CA13850 08/30/04
Center for Applied Engineering TAS 100 257989 04/01/97
PRI Asphalt Technologies, Inc. TAS 100 GAF-912-02-01 12/17/18
PRI Asphalt Technologies, Inc. TAS 100 GAF-044-02.O1 01/13/04
PRI Asphalt Technologies, Inc. TAS 100 GAF-098-02-01 11/08/05
PRI Asphalt Technologies, Inc. TAS 100 GAFA OI1 02-01 11/09/05
PRI Asphalt Technologies, Inc. TAS 100 GAF416-02-02 03/23/06
PRI Asphalt Technologies, Inc. TAS400 ELK-083-02-01 10/16/02
ELK-084-02-01 10/15/02
ELK-085-02-01 10/14/02
ELK-086-02-01 10/24/02
ELK-087-02-01 10/21/02
ELK-088-02-01 10/16/02
ELK407-02-01 10/09/03
ELK-108-02-01 10/09/03
ELK4 09-02-01 10/09/03
NOA No.: 19A312.04
NIAM4DADE COUNTY M
O Expiration Date: 02/21/22
WApproval Date: 01/09/20
Page 4 of 7
:
LIMITATIONS
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. Shall not be installed on roof mean heights in excess of 33 il.
3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
INSTALLATION
1. Shingles shall be installed in compliance with Roofing Application Standard RAS 115.
2. Flashing shall be in accordance with Roofing Application Standard RAS 115
3. The manufacturer shall provide clearly written application instructions.
4. Exposure and course layout shall be in compliance with Detail 'A', attached.
5. Nailing shall be in compliance with Detail 'B', attached.
LABELING
Shingles shall bear the imprint or identifiable marking of the manufacturer's name or logo, city and state of
manufacturing facility, and following statement: "Miami-Dade County Product Control Approved" or the Miami-Dade
County Product Control Seal as shown below.
AMMEENNIMENNEENNININk
tMIAM ADE C®UN�
BUILDING PERMIT REQUIREMENTS uE
1. Application for building permit shall be accompanied by copies of the following:
1.1 This Notice of Acceptance.
1.2 Any other documents required by the Building Official or the applicable code in order to properly
evaluate the installation of this system.
I
NOA No.: 19-0312.04
M
r OADE COUNTY Expiration Date: 02/21/2N2
r
Approval Date: 01/09/20
Page 5 of 7
DETAm A
COURSE LAYOUT
9
DECK `
FULL
i
5th
17" OFF 4th
11 " OFF 3rd
I
6" OFF 2nd
FULL 1st 5-5/8" Exposure
NOA No.: 19-0312.04
MIAMI•DADE COUNTY Expiration Date: 02/21/22
• e e
Approval Date: 01/09/20
Page 6 of 7
DETAIL B /y
OVERALL DIlV> NSIONS AND N PATTERN
FOR TIMBERLINE HDO TIMBERLINE® NATURAL SHADOW® AND TIMBERLINE NS
39- 3/3 "
(5m)
4 14-112"
oEs- xs _� - 117f,1121 I 32" - - ps s/2- z"
(368 - 445 ) 8 - 445mm) n mml "
ail g-u6i-d5/e4"line
it 6-1 /2 - 9 6-1 /2" - 9-1/2 5-3f4"A31_@3]1�) 4 (146mm - 159mm)
from bottom of shingle
elf seal
adhesive
on back
ENHANCED NAILING PATTERN - six nails per shingle'
required by soma local codes and required for enhanced Mad coverage on certain Products.
See limited warranty for details.
These shingles MUST be nailed a nominal 6" (152mm) from bottom of
of shingle, above the cut outs, as shown. Nails must not be exposed.
I
OVERALL DIMENSIONS AND NAILING PATTERN
FOR TIMBERLINE® HDZT"9 TIMBERLINE® CS9 TIMBERLINEOA119 AND
FORTITUDE®
39-3/8" ( 1 m )
b 144Y - 17-1i7,(368 aim - 445 mm) to 12 - 17-112` f369 mm - 445mml
6-1/4' g-V2` (165 mm - 241 mm) 61/2 - 9-112T65 ram - 241 mml
12' 2-12' (13 mm 34 mm) 112' - 2- 2T3mm - 64 ro
13-1M j
t
37 n
3 mi
---- TARGET �
NAIL ZONE
cr1 ;116' - 64/4' 5-13/1 G - 7-5/8"
(14B mm -159 mm) (146 mm - 194 mm)
For Mansard Roofs
El I
E OF TIIIS ACCEPTANCE
MfAMo-r>I+oE counnv NOA No.: 19-0312.04
c Expiration Date: 02/21/22
Approval Date: 01/09/20
Page 7 oT 9
8/24/2021 TFWZ.R21 • Prepared Roof-covering Materials ( UL Product iQ
UL Product 1Q'm �L I
1
TFWZ , R21 - Prepared Rookovering Materials
Prepared Rookoverin Mater_iz.s
GAF — R21
1 Campus Dr
Parsippany, NJ 77054 United Stat s
gpha1 glass fiber matshingles - ' oyal Sovereign ®", "Sentinel ® ", "Sentinel® ASTM D3462", "Timberline® HD", "Timberline® Natural
Shadow® ", "Timberlines NY, "Timberline® Ultra HD", "Timberline® UHW. "Timberline® Cool Series®", "Timberline® American Harvest'"",
"Timberlines HDZ""", "Timberlines AW or "Timberlines CS", "Fortitude'"", "Timberlines ArmorShieldTM II", "Timberlines AS 11", "Marquis
WeatherMaxs", "Grand Canyons", "Grand Sequoias", "Grand Sequoias ArmorShieldTM", "Grand Sequoias AS", "Camelots", "Camelots II",
"Slateiines ", 'Woodlands", "Siennas" or "Glenwoods " for installation as a Class A prepared roof covering. Suitable for installation on minimum
3/841n. thick plywood roof decks in combination with a minimum of one ply of "Shingle-Mates Roof Deck Protection", Type 15 or Type 30
underlayment. Also Classified in accordance with ASTM D3161/D3161M, Class F. Also Classified in accordance with ASTM D3462/D3462M, Also
Classified in accordance with [CC ES AC438.
Asphalt glass fiber mat shingles - "Pro-Startm Starter Strip Shingles" for installation as a Class A prepared roof covering. Suitable for installation
on minimum 3/84n, thick plywood roof decks in combination with a minimum of one ply of "Shingle-Mates Roof Deck Protection", Type 15 or
Type 30 underlayment, Also Classified In accordance with ASTM D3161/D3161 M, Class F.
Asphalt glass fiber mat shingles - "WeatherBlockerTM Premium Eave/Rake Starter Strip Shingles" for installation as a Class A prepared roof
covering. Suitable for installation on minimum 3/84n. thick plywood roof decks in combination with a minimum of one ply of "Shingle-Mates
Roof Deck Protection", Type 15 or Type 30 underlayment. Also Classified in accordance with ASTM D3161/D3161 M, Class F. Also Classified in
accordance with ASTM D3462/D3462M.
Asphalt glass fiber mat shingles, "Royal Sovereigns", "Sentinels ", "Timberlines HD", "Timberlines Natural Shadowe ", "Timberlines NS",
"Timberlines Ultra HD", "Timberlines UHD", "Timberlines Cool Serless ", "Timberlines American Harvestm", "FortitudeTM", "Marquis
WeatherMaxe ", "Grand Canyons ", "Grand Sequoias " and "Camelots " for installation as Class A prepared roof covering when used with
minimum Type 30 underiayment over existing wood shingle roof.
l
Asphalt glass mat hip and ridge shingles- "Timbertexs Hip and Ridge" for installation as Class A prepared roof covering. Also been evaluated in
accordance with ASTM D3161/D3161M, Class F when Henkel "Pt. Roofing and Flashing Sealant" or Sonneborn "NP7 Gun-Grade Polyurethane
Sealant" is applied as specified in manufacturer's application instructions."
Asphalt glass mat hip and ridge shingles, "Zs Ridge Cap Shingles", "TimberCrest'"' Premium SBS-Modified Ridge Cap Shingle", "TlmberCrests
i
AS Premium SOS-Modified IR Ridge Cap Shingles", "TimberTexs Premium Ridge Cap Shingles", "Ridglasss Premium Ridge Cap Shingles", for
installation as Class A prepared roof coverings. Also been evaluated in accordance with ASTM D3161/D3161 M, Class A.
Asphalt glass mat hip and ridge shingles, "Zs Ridge Cap Shingles", "TimberTexs Premium Ridge Cap Shingles", for installation as Class A
prepared roof coverings. Also been evaluated in accordance with ASTM D3161/D3161 M, Class F when Henkel Corp. "Loctite PL Roof & Flashing
Polyurethane Sealant" is applied as specified in manufacturer's installation instructions.
Asphalt glass mat hip and ridge shingles, "Seal-A-Ridges Protective Ridge Cap Shingles" , "SeakA-Rldges ArmorShieldTM" and "SeaI-A-Ridges
AS SBS-Modified IR Ridge Cap Shingles" for installation as Class A prepared roof coverings. Also been evaluated in accordance with ASTM
D3161/D3161M, Class F.
Asphalt glass mat hip and ridge shingles, "TimberCrestTM Premium SBS-Modified Ridge Cap Shingle" or "TlmberCrests AS Premium SOS-
Modified IR Ridge Cap Shingles" for installation as Class A prepared roof covering. Also been evaluated in accordance with ASTM D3161/D3161M,
Class F when ASTM C920 Henkel "Loctite Pl. Roofing and Plashing Sealant' is applied as specified in manufacturer's installation instructions.
Last Updated on 2021 -08-11
The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured
under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under U12s Follow-Up
Service. Always look for the Mark on the product.
8124/2021 TFWZ.R21 If Prepared Roof-covering Materials i UL Product IQ
UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1 . The Guide
Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non-misleading
manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission i
from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following
format: V 2021 UL LLC"
i
I�
f
1
f
I
i
t
t
a
py
B