The URL can be used to link to this page

Home My WebLink AboutAPPROVED Boral Estate 21042005 NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 1 of 7 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy Boral Roofing, LLC 7575 Irvine Center Drive, Suite 100 Irvine, CA 92618 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to be used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (in Miami-Dade County) and/or the AHJ (in areas other than Miami-Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Estate “S” Tile LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA# 21-0323.05 and consists of pages 1 through 7. The submitted documentation was reviewed by Alex Tigera. NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 2 of 7 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub Category: Roofing Tiles Material: Concrete 1. SCOPE This approves a roofing system using Boral Estate “S” Concrete Roof Tile, as manufactured by Boral Roofing, LLC in Okeechobee, FL as described in Section 2 of this Notice of Acceptance, designed to comply with the Florida Building Code for High Velocity Hurricane Zone. For use in locations where the pressure requirements, as determined by applicable Building Code, do not exceed the design pressure values obtain by calculations in compliance with RAS 127 using the values listed in section 4 herein. The attachment calculations shall be prepared as a moment based system. 2. PRODUCT DESCRIPTION Manufactured by Applicant Dimensions Test Specifications Product Description Boral Estate ‘S’ Roof Tile Length = 16-1/2" Width = 13" TAS 112 Type 1b Class III Low profile, interlocking, extruded concrete roof tile equipped with two nail hole and double roll ribs. For direct deck or battened nail-on, mortar or adhesive set applications. Trim Pieces l = varies w = varies varying thickness TAS 112 Accessory trim, concrete roof pieces for use at hips, rakes, ridges and valley terminations. Manufactured for each tile profile. 2.1 MANUFACTURING LOCATION 1. Okeechobee, FL 2.2 PRODUCTS MANUFACTURED BY OTHERS Product Name Product Description Manufacturer (With Current NOA) ICP Adhesives Polyset® AH-160 Two component polyurethane foam adhesive. ICP Adhesives and Sealants, Inc. TILE BONDTM Roof Tile Adhesive Single component polyurethane foam roof tile adhesive. The Dow Chemical Company Touch ‘N Seal StormBond® 2 Two- Component Polyurethane Roof Tile Adhesive Two component polyurethane foam adhesive. DAP Foam, Inc. Touch ‘N Seal StormBond® One Component Polyurethane Roof Tile Adhesive One component polyurethane foam adhesive. DAP Foam, Inc. NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 3 of 7 2.3 EVIDENCE SUBMITTED: Test Agency Test Identifier Test Name/Report Date Redland Technologies 7161-03 PA 102 Dec. 1991 7161-03 PA 102(A) Dec. 1991 7161-03 PA 108 Dec. 1991 P0402 Withdrawal Resistance Testing of screw vs. smooth shank nails Sept. 1993 P0631-01 PA 108 July 1994 Letter Dated Aug. 1, 1994 PA 108 Aug. 1994 Professional Service Industries, Inc. 224-47099 PA 112 Sept. 1994 The Center for Applied 94-060B PA 101 March, 1994 Engineering, Inc. 94-084 PA 101 May 1994 25-7094-1 PA 102 Oct. 1994 25-7094-7 PA 102 Oct. 1994 25-7094-4 PA 102 Oct. 1994 Project No. 307025 Test #MDC-76 PA 100 Oct. 1994 25-7183-1 PA 102 Feb. 1995 25-7183-2 PA 102 Feb. 1995 25-7214-2 PA 102 March, 1995 25-7214-6 PA 102 March, 1995 Celotex Corporation Testing Services 528454-2-1 520109-2 PA 101 Sep. 1998 Dec. 1998 Walker Engineering, Inc. Calculations Aerodynamic Multiplier March 1999 IBA Consultants, Inc. 2381-264 TAS 112 01/08/08 American Test Lab of South Florida RT0201.02-21 TAS 112 02/12/21 PRI Construction Material DAPF-004-02-05 TAS 101 07/26/18 Technologies DAPF-004-02-07 TAS 101 07/26/18 2002T0003.04 TAS 101 11/06/20 NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 4 of 7 3. LIMITATIONS: 3.1 Fire classification is not part of this acceptance. 3.2 For mortar or adhesive set tile applications, a static field uplift test in accordance with TAS 106 may required, refer to applicable building code. 3.3 Applicant shall retain the services of a Miami-Dade County Certified Laboratory to perform quarterly test in accordance with TAS 112, appendix ‘A’. Such testing shall be submitted to the Miami-Dade Product Control Section for review. 3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed section 4.1 herein. 3.5 Minimum slope 4/12 for mechanically attached tile. 3.6 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated otherwise by the underlayment material manufacturers published literature. 3.7 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with applicable building code. 3.7 All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. 4. INSTALLATION 4.1 Boral Estate “S” Concrete Roof Tile and its components shall be installed in strict compliance with Miami Dade County Roofing Application Standard RAS 118, RAS 119, and RAS 120. 4.2 Data For Attachment Calculations. Table 1: Average Weight (W) and Dimensions (l x w ) Tile Profile Weight-W (lbf) Length-l (ft.) Width-w (ft.) Boral Estate ‘S’ Roof Tile 10.0 1.375 1.08 Table 2: Aerodynamic Multipliers -  (ft3) Tile Profile  (ft3) Batten Application  (ft3) Direct Deck Application Boral Estate ‘S’ Roof Tile 0.267 0.289 Table 3: Restoring Moments due to Gravity - Mg (ft.-lbf) Tile Profile 3":12" 4":12" 5":12" 6":12" Greater than 7":12" Boral Estate ‘S’ Roof Tile Battens Direct Deck Battens Direct Deck Battens Direct Deck Battens Direct Deck Battens Direct Deck N/A 6.74 5.82 6.64 5.70 6.50 5.56 6.33 5.40 6.14 NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 5 of 7 Table 4: Attachment Resistance Expressed as a Moment - Mf (ft-lbf) for Nail-On Systems Tile Profile Fastener Type Direct Deck (min 15/32” plywood) Direct Deck (min. 19/32” plywood) Battens Boral Estate ‘S’ Roof Tile 2-10d Ring Shank Nails 27.8 37.4 28.8 1-10d Smooth or Screw Shank Nail2 8.8 11.8 4.1 2-10d Smooth or Screw Shank Nails 16.4 21.9 7.1 1 #8 Screw2 25.8 25.8 22.9 2 #8 Screw 47.1 47.1 49.1 1-10d Smooth or Screw Shank Nail (Field Clip)2 24.3 24.3 24.2 1-10d Smooth or Screw Shank Nail (Eave Clip)2 19.0 19.0 22.1 2-10d Smooth or Screw Shank Nails (Field Clip) 35.5 35.5 34.8 2-10d Smooth or Screw Shank Nails (Eave Clip) 31.9 31.9 32.2 2-10d Ring Shank Nails1 43.0 67.5 50.9 1 Installation with a 4" tile headlap and fasteners are located a min. of 2½" from head of tile. 2 When using only one fastener use the hole that is approximately 4-3/4” away from interlocking edge. Table 5: Attachment Resistance Expressed as a Moment Mf (ft-lbf) for Two Paddy Adhesive3 Set Systems + Tile Profile Tile Application Minimum Attachment Resistance Boral Estate ‘S’ Roof Tile TILE BOND™ Roof Tile Adhesive 674 TILE BOND™ Roof Tile Adhesive 355 ICP Adhesives Polyset® AH-160 26.16 Touch ‘N Seal StormBond® 2 357 Touch ‘N Seal StormBond® (one component) 628 3 See foam adhesive manufacturer’s component approval for installation requirements. 4 Medium paddy weight of 16 grams per paddy of TILE BOND™ Roof Tile Adhesive 5 Medium paddy weight of 8 grams per paddy of TILE BOND™ Roof Tile Adhesive 6 Medium paddy weight of 8 grams per paddy of Polyset® AH-160 7 Medium paddy weight of 8 grams per paddy of Touch ‘N Seal StormBond ® 2 8 Medium paddy weight of 8 grams between tile and underlayment, paddy weight of 5 grams on overlap of tile of Touch ‘N Seal StormBond ® (one component) NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 6 of 7 Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-lbf) for Single Paddy Adhesive Set Systems Tile Profile Tile Application Minimum Attachment Resistance Boral Estate ‘S’ Roof Tile ICP Adhesives Polyset® AH-160 86.69 ICP Adhesives Polyset® AH-160 45.510 Touch ‘N Seal StormBond® 2 6011 9 Large paddy weight of 54 grams of Polyset® AH-160 10 Large paddy weight of 24 grams of Polyset® AH-160 11 Large paddy weight of 60 grams of Touch ‘N Seal StormBond ® 2 Table 7: Attachment Resistance Expressed as a Moment - Mf (ft.-lbf) for Mortar or Adhesive Set Systems Tile Profile Tile Application Minimum Attachment Resistance Boral Estate ‘S’ Roof Tile Mortar Set 20.60 5. LABELING All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as seen below or following statement: "Miami-Dade County Product Control Approved". OR BORAL ESTATE “S” TILE LABEL (LOCATED ON UNDERSIDE OF TILE) 6. BUILDING PERMIT REQUIREMENTS: 6.1 Application for building permit shall be accompanied by copies of the following: 6.1.1 This Notice of Acceptance. 6.1.2 Any other documents required by Building Official or Applicable building code in order to properly evaluate the installation of this system. NOA No. 21-0420.05 Expiration Date: 08/23/26 Approval Date: 08/26/21 Page 7 of 7 PROFILE DRAWING BORAL ESTATE “S" CONCRETE ROOF TILE END OF THIS ACCEPTANCE