HomeMy WebLinkAboutAPPROVED Roof Info SheetsST. LUCIE
Master Permit No.
Section A (General Information)
Process No.
contractors Nrr", P?ckard Roofing License X CCCAIl517
Job Address 7963 Plantation Lakes Dr.
El Low Slope
E Asphaltic Shingles
ROOF CATEGORY
Et Mechanically Fastened Tile E MortarlAdhesive Set Tiles
E Metal Panel/Shingles BIVood Shingles/Shakes
E Presriptive BUR-RAS 150
ROOF ROOF TYPE-
E New roof EI Repair E Maintenance E Reroofing E Recovering
. ROOF SYSTEM INFORMATION
Low Slope Roof Area (SF)
-
Steep Sloped Roof Area (SF) 5200 Total (SF) 5200
Section B (Roof Plan)
Sketch Roof Plan: lllustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
lnclude dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
I
Plan Diagram
\
Ridge
-
High Drip
Hip
Valley
-
Eave
-
Rake
-
Parapet
Protrusion
Apron Flashing - -
StepFlashinS ---
Pitch Change
To improve readability the lengths displayed in this diagram are rounded to the nearest whole number. Lengths under 4 feet are omitted for clarity.
169't 5'.12 96 5:'12
1123 5:12 96 5:12
C 547 5-.12 60 5'.12
D 415 5:12 57 5:12
323 5:12 M 49 5:12
234 5:12 N 47 5:12
G 183 5:12 o 46 5:12
163 5:12 42 5:12
5-.12
51.7
o%5%lOYo 12/.15"/o 2Oo/o
51.7 54.3 56.9 57.9 59.4 62.0
The waste factors presented in the table are simple calculations based on the total area of the roof. They do not include any other roofing elements such as ridge, valley or hips.
Use your best judgemeni and past experience to select the waste facior that works best for this particular roof.
.
Facet Sq.Ft. Pitch Facet Sq.Ft. Pitch
A
B
K
H
AREA BY PITCH (in squares)
WASTE FACTOR TABLE (in squares, includes pitched and flat totals)
ST. LUCIE WORKS
Section D {Steep Slope Roof System)
Roof System Manufacturer; &l MTS Ptus
Notice of Acceptance Number: FL5259-R33
Minimum Design wind Pressures, lf Applicable (From RAS 127 or Calculations):--- ;.;; ;-?8 ion" z",|78 zonezn;1 1L zsns27'.-1 1 4.7onu g", -1 1{one :r:-1 36
Ridge Ventilalion?
No
Plywood
Type UnderlaYment 30# felt and self adhering
lnsulation:
Fire Banier:NA
Fastener Type & Spacing:tin caps, 1 1/4 ring shank ils
Adhesiw Type:NA
Type Cap Shet:MTS Plus self adhering
Mean Roof Height:1''.Rmf Covaing:
Type & Size DriP
Edge:
3x3 galvanized
NA
tile
ST. LUCIE WCHI
Section E (Tile Calculations)
For Moment based tile systems, choose either Metho d L or z.compare the values for Mr with the values from Mr' lf the Mt values
are greater than or equat to the Mr values, for each area of the roof, then the tile attaehment method is acceptable'
Method 1 'Moment Based Tile Calculations Per RAS 127
(zone1:
-xL-= -J-Mg:--M"-
ProductApprovalML-
{Zone2e: xf
-= -J-Mg:-=y^-
ProductApproval Mr-
{Zone 2n:
-x
l-=
-)
-Mg:
-=Mrar-
Product Approval Mr--
(Zone2r:
-xl-=
)-Mg:--M,a- ProductApproval Mt.-
{Zone 3e:
-xl-= -J
-Mg:
-=MBe-.
ProductApproval Mr--
(Zone3r:
-xi.-=
-J-Mg:-=M&- ProductApproval Mr-
4:12
5:12
*fvf ust U. ui"O in conjunction with a list of moment based tile sYstems
. For Uplift based tile systems use Method 3. Compare the values for F' with the values for F, lf the F' values are greater than or
equal to the Fr values, for each area ofthe roof, then the tile attachment method is acceptable'
Method 3 "Uplift Based Tile Calcuiations Per RAS 127
(Zone 1: L-=x W;=-) -W:- cos r-_=F't- Product Approval t'-
{Zone 2e:
-x
L-_=x w:=.--) -w:- cos l-------:=Frze- Product Approval F'...'..----
(Zone2n:L-=xW:=)-W:-cosr-=FQn-ProductApprovalF,-
lkonezri L--=xW:=----) -Wl-cos r-=F''\- ProductApproval F'
-
{Zone 3e:
-x
L-=1\A/;= ) -w:- cos r-----:=f *e- Product Approval F'-
(Zone3r:xL-=xW:=-).W:-cosf_----;=Frzr-ProductApprovalF,-
Method 2 "simplified Tile Calculations Per Table Below"
Required Moment o, *"r,r,un.u,,r, ,ro.,ub'u '"'o*zdA-"od"t
oop'o'"' ''g'1-
Mr requlred Moment Resistance*
Mean Roof Height Roof Slope t5'
2:72 ) 34.4
3:!2 | zz.z
From applicable table in RAS 127 or by an engineering analysis
by PE based on ASCE 7Zones 1, 2e, 2n, 2r ,3e,3r
All calculations must be submitted to the building official at the time of permit application
36.s 38.2 39.7 42.2
34.4 35.0 37.4 39.8
30.4 32.2 33.8 3s.1 37.3
28.4 30.1 31.6 32.8 34.9
5:12 26.4 28.0 29.4 30.5 32.4
7'.r2 24.4 25.9 27.!28.2 30.0
Where to Obtain lnformation