HomeMy WebLinkAboutGENERAL INFORMATION SECTION ASection A (General Information)
Master Permit No'�y k — ��' 1... Process No,
Contractors Name: -{-''r ,./ V 04A t L-e _ ;✓%cAe jVLicense (�
Job Address :VD �� 11 .Irl,'A 1'L)IIyA A�P' V+ -1"'%rrr7 �L� 5g9&51
ROOF CATEGORY
Aow Slope ❑ Mechanically Fastened Tile ❑Mortar/Adhesive Set Tiles
XAsphaltic Shingles ❑ Metal Panel/Shingles ❑Wood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE.
❑ New roof ❑ Repair ❑ Maintenance Z'Reroofing ❑ Recovering
. ROOF SYSTEM INFORMATION ����
Low Slope Roof Area (SF) 3` 5S Steep Sloped Roof Area (SF) 25y I Total (SF)
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
If a component is not used, identify as "NA") id
System Manufacturer: i O[11 tots3
Product Approval No.: I I' ®.l)i � O
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1':'37zone1:'&Y Zone 2"i'gYZone 3: "ISS
Max. Design Pressure, from the specific product approval
system: ® .2, ri
Deck: p t,
Type: 'i ta, / GaugeThickness:
Slope: • t7°
Anchor/Base Sheet & No. df Ply(s): E (Ag /7 b0c,
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheets) & No. of Ply(s):
Base Sheet Fastener/Bonding Material:
Ply Sheet(s)' & No. of Ply(s): Ei'n/pFfcc SA ti r(I
Ply Sheet Fastener/Boand�ing M terial:
1eI� it��t`c�
Top Ply: EI,S/0 r/eX 014 if L*4
Top Ply Fastener/Bonding Material:
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1': .1" oc @ Lap, # Rows 3 ® ` "oc -
Zone 1: $ " oc @ Lap, # Rows 3 @ 4 oc
Zone 2: " oc @Lap, #Rows 3 ®�" 00
Zone 3: g " oc @ Lap, # Rows,`% @ '�" 00
Number of Fasteners Per Insulation Board:
Zone 1':—Zone 1:_Zane 2:_Zone 3:_
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc.,
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16..
FT.
Parapet
Height
FT. 17�}^S�o'b�SG Mean
Roof
K 2 Height
oL �r(Sf-9F(GR SJT V
% 3x3 ,6
E)�SkFIC� 4A P