Loading...
HomeMy WebLinkAboutAPPROVED SSS_Poles_SpecSheet_SPECIAL FL WINDLOADING 03 06 20US: creelighting.com (800) 236-6800 Canada: creelighting-canada.com (800) 473-1234 SSS Series Crown-Weld® Straight Square Steel Poles Anchor Bolts (Pole must be ordered separately) SSS- SSS-4-AB-3/4-28 Anchor Bolts/Template, 3/4" Diameter, 4" Poles (15'+) *Order tenon separately. Refer to Bracket and Tenons spec sheet for additional information Product Description Cree Lighting’s proprietary Crown-Weld® pole base crown weld configuration was designed to minimize stress in areas most vulnerable to failure, provide superior strength and higher wind load ratings, than poles of similar height and cross-section. Both premium pole design and extended life finish combine for a 7-year limited warranty for a reduced lifetime cost of ownership. Non-tapered square steel poles are supplied with a painted galvanized steel 2-piece base cover, four partially galvanized anchor bolts, Masonite mounting template and pole cap (except open top mount). Steel pole base has slotted holes to accommodate installation. A standard 3" x 5" hand hole is located 14" above the bottom of pole base. A 1/2" stainless-steel weld stud with grounding lug is located inside the pole, opposite the hand hole. Cree Lighting poles are steel shot cleaned to remove any rust, mill scale, oxides, or other unwanted particles from the pole resulting in a surface preparation that exceeds the specifications published by the SSPC-SP10. Iron phosphate is then applied, creating an iron oxide base with a flat or amorphous metal phosphate topcoat. This coating significantly adds to the performance of the finished coating by improving bonding and minimizing the spread of oxidation if the coating is scratched, improving corrosion resistance. Polyester powder coating is applied to a 6-mil thickness. CONSTRUCTION & MATERIALS •Square, non tapered pole of structural steel tubing (ASTM A 500 Grade B) with a minimum yield strength of 50,000 p.s.i. welded to a formed carbon steel base plate (ASTM A-36 HRS) with a mini- mum yield strength of 36,000 p.s.i. •Anchor bolts (F1554 Grade 55) are "L" bent bars having a minimum yield strength of 55,000 p.s.i. The bolts are at least partially galvanized per ASTM A153 specifications and furnished complete with two (2) hex nuts and 2 flat washers •Base cover is 2 pc.16 ga. painted galvannealed steel which connects with two 410 stainless steel screws included •Pole cap is painted PVC •Optional GFI receptacle available. Refer to page 3 for details REGULATORY & VOLUNTARY QUALIFICATIONS •National Electrical Code Requirements •UL Listed in US for electrical ground bonding •CSA Certified in Canada for ground bonding and structural strength •RoHS Compliant (consult factory for details) LIMITED WARRANTY† •7 years on pole and tenons/7 years on finish /1 year on GFI receptacle Ordering Information Fully assembled pole is composed of two components that must be ordered separately. If required, a GFI must also be requested at time of order. Example: Anchor Bolts: SSS-4-AB-3/4-28 + Pole: SSS-4-7-25-CW-BS-1D-C-BZ + Optional GFI: SSS-GFI-STANDARD Pole (Anchor bolts must be ordered separately) SSS 4 7 CW BS Design Cross Section Material Shaft Size Wall Thickness (GA)Mounting Height Base Type Base Casting/ Cover Mounting Configuration Fixture Mounting Pattern Finish S Straight S Square S Steel 4 = 4"7 7 gauge (0.188") 15 = 15' 17 = 17' 20 = 20' CW Crown Weld BS Standard Metal 1D Drilled Single 2D90 Drilled 2@90deg 2D18 Drilled Twin@180deg 3D90 Drilled 3@90deg 4D90 Drilled 4@90deg OT* Open top to accept internal mount tenons or brackets C Standard - Not available with OT mounting configuration - Not for use with THE EDGE® High Output luminaires N None - Required with OT mounting configuration - Not available with mounting configurations other than OT BK Black BZ Bronze SV Silver WH White † See http://creelighting.com/warranty for warranty terms CA RESIDENTS WARNING: Cancer and Reproductive Harm – www.p65warnings.ca.gov Rev. Date: V1 03/06/2020 Crown-Weld Base Optional GFI (Pole and Anchor Bolts must be ordered separately) SSS-GFI-STANDARD - Located 28" above the base of the pole on same side as hand hole. Consult factory for placement in other locations - Not available with 3" poles US: creelighting.com (800) 236-6800 Canada: creelighting-canada.com (800) 473-1234 Crown-Weld® Straight Square Steel Poles Pole Drawing Base Plate Detail Hand Hole Drawings Anchor Bolt Detail L M J A B H D C 14" D E F G 3.4" 5.4" K Grounding at 270° Weld Seam at 0°180° Side Hand Hole at 90° Hand Hole Extrusion Rim TOP VIEW Ground Screw Hand Hole Gasket Hand Hole Locking Bar (2) Flat Washers - Zinc 3.4" x 5.4" Hand Hold Cover 1/2 UNC Grounding Nut- Zinc ISOMETRIC VIEW Pole Width Pole Height Part Number Anchor Bolt Diameter (K) Anchor Bolt Vertical Length (L) Anchor Bolt Horizontal Length (M) 4"15' +SSS-4-AB-3/4-28 0.75"24"4" US: creelighting.com (800) 236-6800 Canada: creelighting-canada.com (800) 473-1234 Crown-Weld® Straight Square Steel Poles Fixture Mounting Drill Patterns 1.0" 2.0"2.0" 0.375"0.375" 0.50" 0.344" 2.0" C - Standard Cree Lighting Fixture Mounting Pattern (Not for use with THE EDGE® High Output Luminaires) Open Top Mounting Configuration Tenons and Brackets‡ (must specify color) Square Internal Mount Vertical Tenons (Steel) - Mounts to 3-6" (76-152mm) square aluminum or steel poles - For use with adjustable arm & horizontal/vertical tenon mounts PB-1A* – Single PB-4A*(90) – 90˚ Quad PB-2A* –180˚ Twin PB-4A*(180) –180˚ Quad PB-3A* –180˚ Triple Square Internal Mount Vertical Tenons (Aluminum) - Mounts to 4" (102mm) square aluminum or steel poles - For use with adjustable arm mounts and RUL luminaires - Not for use with THE EDGE® or OSQ™ High Output Area/Flood luminaires PD-2A4(90) – 90˚ Twin PD-3A4(90) –90˚ Triple PD-2A4(180) –180˚ Twin PD-4A4(90) –90˚ Quad Square Internal Mount Vertical Tenons (Steel) - Mounts to 4" (102mm) square aluminum or steel poles - For use with horizontal tenon mounts that require extended tenon length - Not for use with THE EDGE® or OSQ™ High Output Area/Flood luminaires PD-1H4 – Single PD-3H4(90) – 90˚ Triple PD-2H4(90) –90˚ Twin PD-4H4(90) –90˚ Quad PD-2H4(180) –180˚ Twin Mid-Pole Bracket (Steel) - Mounts to square pole - For use with adjustable arm & horizontal/vertical tenon mounts PW-1A3** – Single PW-2A3** – Double Direct Arm Pole Adaptor Bracket (Aluminum) - Mounts to 3-6" (76-152mm) round or square aluminum or steel poles - For use with horizontal tenon mounts that require extended tenon length - Not for use with THE EDGE® or OSQ™ High Output Area/Flood luminaires XA-TMDA8 Tenon EPA ‡ Refer to the Bracket and Tenons spec sheet for more details on tenons. Refer to product specification sheets for compatible tenons * Specify pole size: 3 (3"), 4 (4"), 5 (5"), or 6 (6") for single, double or triple luminaire orientation or 4 (4"), 5 (5"), or 6 (6") for quad luminaire orientation ** These EPA values must be multiplied by the following ratio: Fixture Mounting Height/Total Pole Height. Specify pole size: 3 (3"), 4 (4"), 5 (5"),or 6 (6") Part Number EPA PB-1A* None PB-2A*0.82 PB-3A*1.52 PB-4A* (180)2.22 PB-4A* (90)1.11 PD Series Tenons 0.09 PW-1A3**0.47 PW-2A3**0.94 XA-TMDA8 0.07 Optional GFI CONSTRUCTION & MATERIALS • Heavy-duty steel construction • Lockable security cover • Includes adapter plates and foam gasket • 20A, 120V, 60Hz GFCI, and cover also included • 3-1/4" internal depth • Standard GFI is located 28" above the pole base on the same side as the hand hole. Consult factory for placement in other locations • Weatherproof while in use • Meets NEC Extra Duty requirements • Receptacle and cover ship separately in hardware bag Crown-Weld® Straight Square Steel Poles US: creelighting.com (800) 236-6800 Canada: creelighting-canada.com (800) 473-1234 © 2020 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is subject to change. Patent www.creelighting.com/patents. Cree® and the Cree logo are registered trademarks of Cree, Inc. Crown-Weld® and THE EDGE® are registered trademarks, and OSQ™ is a trademark of Cree Lighting, A company of IDEAL INDUSTRIES. The UL logo is a registered trademark of UL LLC. Product Width (A) x Wall (B) x Height (C) Base Plate (D) x Thickness Bolt Circle Range Min (E) - Max (F) Bolt Hole Size (G) Base Cover (H) x Height (J) Pole EPA Rating – Base Wind Velocity (MPH) Maximum Luminaire Weight Approx. Shipping Weight80 90 100 110 120 130 140 150 160 170 180 SSS-4-7-15-CW-BS 4" x 7ga. x 15' 10" Sq. x 0.75"9.25"- 11"0.88"10.44" SQ x 5.5" 59.0 45.8 36.5 29.6 24.3 20.3 17.5 14.5 12.3 10.5 8.4 350 lbs. (159kg) 140 lbs. (64kg) SSS-4-7-17-CW-BS 4" x 7ga. x 17' 10" Sq. x 0.75"9.25"- 11"0.88"10.44" SQ x 5.5" 49.7 38.5 30.6 24.6 20.1 16.5 13.8 11.5 9.7 8.2 6.5 350 lbs. (159kg) 155 lbs. (70kg) SSS-4-7-20-CW-BS 4" x 7ga. x 20'10" Sq. x 0.75"9.25"- 11"0.88"10.44" SQ x 5.5"39.5 30.4 23.8 18.9 15.2 12.3 10.0 8.1 6.7 5.4 3.3 350 lbs. (159kg) 177 lbs. (80kg) Dimensions, EPA & Weight NOTE: Hanging signs, banners and flags on poles changes the EPA rating and increases vibration. The EPA ratings data provided does not allow for this added stress which could result in pole or luminaire failure. Calculations per 2017 FBC. See map below.