HomeMy WebLinkAboutAPPROVED SAV SAP NOAMIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION 1n /1 f o , , _ �) Miami, Florida 33175-2474
"P V w« �"�U��- T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) (, www.miamiaade.eov/economy
Polyglass USA, Inc.
150 Lyon Drive
Fernley, NV 89408
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Self -Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA# 17-1016.01 and consists of pages 1 through 38.
The submitted documentation was reviewed by Alex Tigera.
C
ADE COUNTY
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 1 of 38
ROOFING ASSEMBLY APPROVAL
Cateeorv' Roofing
Sub-CateLyorv: Modified Bitumen
Materials SBS/APP/TPO
Deck Type: Wood
Maximum Desisn Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Polyanchor 250' x 48" ASTM D 4601, A polymer woven, high performance, synthetic base
Type H sheet.
Polyglass G2 Base
108' x 36"
ASTM D 4601,
Asphalt -coated fiberglass reinforced base sheet
Type II
Elastoshield HT
65' 8" x 3' 3-3/8"
ASTM D 6162
SBS modified asphalt coated fiberglass/polyester
reinforced base sheet.
XtraFlex SBS HT
65' 8" x 3' 3-3/8"
ASTM D 6162
SBS modified asphalt coated fiberglass/polyester
Base 650
reinforced base sheet.
Elastobase
65' 2" x 3' 3-3/8"
ASTM D 6163,
SBS modified asphalt coated fiberglass reinforced
Type I
base sheet.
Elastoflex SA V
66' 8" x 3' 33/8"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
Elastoflex SA V FR
66' 8" x 3' 3-3/8"
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
Elastoflex SA V
66' 8" x 3' 3 3/s"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
PLUS
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
Elastoflex SA V
66' 8" x 3' 3-3/8"
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
PLUS FR
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
XtraFlex SBS Base
66' 8" x 3' 33/e"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
SA
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
XtraFlex SBS Glass
65' 8" x 3' 3-3/8"
ASTM D 6163,
SBS modified asphalt coated fiberglass reinforced
Base
Type I
base sheet.
Elastobase P
65' 8" x 3' 3-3/8"
ASTM D 6164,
SBS modified asphalt coated polyester reinforced base
Type I
sheet.
Elastoflex SA P
32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
MIAMI•DADE COUNTY
NOA No.: 19-0311.04
�� •
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 2 of 38
Elastoflex SA P FR 32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyfresko G SBS SA 32' 10" x 3' 33/8"
ASTM D 6164,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
Polyfresko G SBS SA 32' 10" x 3' 33/8"
ASTM D 6164,
Self -adhered, fire -rated, fiberglass reinforced, SBS
FR
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyreflect 32' 10" x 3' 3 3/8"
ASTM D 6164,
Self -adhered, polymer, SBS modified bitumen
Type I
membrane with a self -adhering back face and a smooth
top surface.
XtraFlex SBS G SA 32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polybond 32' 10" x 3' 3-3/8"
ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Polyflex 32' 10" x 3' 3-3/8"
ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
XtraFlex APP S 32' 10" x 3' 3-3/8"
ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
PolyKool 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified
Type I bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S 32' 10" x 3' 3 3/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified
SA Type I bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
Polyflex SA P 32' 10" x 3' 3-'/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified
Type I bitumen membrane with a self -adhering back face and
a granule top surface.
Polyflex SA P FR 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, fire -rated, polyester reinforced, APP
Type I modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyfresko G APP SA 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, polyester reinforced, APP modified
Type I bitumen membrane with a self -adhering back face and
a granule top surface.
Polyfresko G APP SA 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, fire -rated, polyester reinforced, APP
FR Type I modified bitumen membrane with a self -adhering back
face and a granule top surface
XtraFlex APP G SA 32' 10" x 3' 33/8" ASTM D 6222, Self -adhered, fire -rated, polyester reinforced, APP
Type I modified bitumen membrane with a self -adhering back
face and a granule top surface.
NOA No.: 19-0311.04
MIAMFDADE COUNTY
� Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 3 of 38
Polyglass APP Base
65' 8" x 3' 3 3/s"
ASTM D 6509,
APP modified asphalt coated fiberglass reinforced
Type I
base sheet.
PG 100
1, 3, 5, 50, 55 gal,
ASTM D41
A penetrating solution of solvent and a blend of
tube or 17 oz. spray
selected asphalts used to promote adhesion.
can
PG 350
1, 3, 5, 50, 55 gal. or
ASTM D3019
A fibered rubberized adhesive designed for use with
tube
Type III
modified bitumen membranes.
PG 400
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use in
tube
ASTM D3409
dry or damp conditions.
PG 425
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use in
tube
ASTM D3409
dry or damp conditions.
PG 450
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement.
tube
PG 500
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use
tube
with modified bitumen membranes.
POLYPLUS 35
1, 3, 5, 50, 55 gal. or
ASTM D3019
A fibered rubberized adhesive designed for use with
tube
Type III
modified bitumen membranes.
POLYPLUS 45
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement.
tube
POLYPLUS 50
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use
tube
with modified bitumen membranes.
XtraFlex 10
1, 3, 5, 50, 55 gal,
ASTM D41
A penetrating solution of solvent and a blend of
tube or 17 oz. spray
selected asphalts used to promote adhesion.
can
XtraFlex 35
1, 3, 5, 50, 55 gal. or
ASTM D3019
A fibered rubberized adhesive designed for use with
tube
Type III
modified bitumen membranes.
XtraFlex 50 Premium
1, 3, 5, 50, 55 gal. or
ASTM D4586
A thick, fibered, rubberized flashing cement for use
Modified Wet/Dry
tube
with modified bitumen membranes.
Cement
WB-3000
5 gallon pail
Proprietary
A low-VOC, water -based acrylic primer to enhance
adhesion of self -adhered membranes.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 4 of 38
APPROVED INSULATIONS:
TABLE 2
Product Name
Product Description
Manufacturer
(With Current NOA)
Polytherm-H
Polyisocyanurate foam insulation
Polyglass USA, Inc.
Polytherm
Polyisocyanurate foam insulation
Polyglass USA, Inc.
Polytherm G
Polyisocyanurate foam insulation
Polyglass USA, Inc.
XtraFlex Polyiso
Polyisocyanurate foam insulation
Polyglass USA, Inc.
XtraFlex Polyiso G
Polyisocyanurate foam insulation
Polyglass USA, Inc.
ACFoam-II
Polyisocyanurate foam insulation
Atlas Roofing Corp
ACFoam-III
Polyisocyanurate foam insulation
Atlas Roofing Corp
Structodek High Density Fiberboard Roof Wood fiber insulation board
Blue Ridge Fiberboard, Inc.
Insulation
DensDeck, DensDeck Prime
Gypsum insulation board
Georgia-Pacific Gypsum LLC
H-Shield
Polyisocyanurate foam insulation
Hunter Panels, LLC
H-Shield CG
Polyisocyanurate/perlite composite insulation
Hunter Panels, LLC
ENRGY-3
Polyisocyanurate foam insulation
Johns Manville Corp.
Fesco Board
Expanded mineral fiber
Johns Manville Corp.
Multi -Max FA-3
Polyisocyanurate foam insulation
Rmax Operating, LLC.
SECUROCK Gypsum -Fiber Roof Board
Fiber reinforced coverboard
United States Gypsum
Corporation
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 5 of 38
APPROVED FASTENERS:
TABLE 3
Product
Product
Name
Description
Dekfast DF-#12-PH3
Insulation fastener for wood,
steel and concrete decks
Dekfast DF414-PH3
Insulation fastener for wood,
steel and concrete decks
Dekfast DF-#15-PH3
Insulation fastener for wood,
steel and concrete decks
Dekfast PLT-H-2-7/8
Galvalume hex stress plate.
Fastener
Number
1.
2.
3.
4.
5.
6.
7.
8.
9.
10
11
12.
13.
14.
15.
16.
17
18
#14 Roofgrip
Flat Bottom Metal Plate
Trufast #14 HD Fastener
Trufast 3" Metal Insulation
Plate
Polygrip Fasteners # 12
Polygrip Fastener #14
Polygrip Fastener #15
Polygrip Hex Plates
OMG 3 in. Ribbed
Galvalume Plate (Flat)
OMG 3" Galvalume Steel
Plate
Dekfast PLT-R-3
Millennium One -Step
Foamable Adhesive
Millennium One Step Green
Foamable Insulation
Adhesive
Millennium PG-1 Pump
Grade Adhesive
Insulation and membrane
fastener
A2-SS aluminized steel plate
Insulation fastener for steel and
wood decks
Round Galvalume AZ50 steel
plate
Insulation fastener for wood,
steel and concrete decks
Insulation fastener for wood,
steel and concrete decks
Insulation fastener for wood,
steel and concrete decks
Galvalume hex stress plate.
Galvalume stress plate.
Galvalume stress plate.
Galvalume stress plate.
A two component, low rise,
polyurethane foam adhesive
A two component, low rise,
polyurethane foam adhesive
A two component, low rise,
polyurethane foam adhesive
Manufacturer
Dimensions (With Current NOA)
SFS Group USA, Inc.
Various SFS Group USA, Inc.
Various SFS Group USA, Inc.
2 '/8" x SFS Group USA, Inc.
3 '/a"
Various OMG, Inc.
3" square OMG, Inc.
Altenloh, Brinck & Co.
U.S., Inc.
3.23 round Altenloh, Brinck & Co.
3" round U.S., Inc.
Various Polyglass USA, Inc
Various Polyglass USA, Inc.
Various Polyglass USA, Inc.
2 7/8" x
Polyglass USA, Inc
3 1/4"
3" round
OMG, Inc.
3" round
OMG, Inc.
3" round
SFS Group USA, Inc.
Adco Products, Inc. dba
Royal Adhesives &
Sealants
Adco Products, Inc. dba
Royal Adhesives &
Sealants
Adco Products, Inc. dba
Royal Adhesives &
Sealants
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 6 of 38
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's
application instructions.
Number Product
Product
Application
Specification
Manufacturer
Name
Description
Rate
1. Gravel
To be installed in a flood coat
4001bs/sq
N/A
Generic
of approved asphalt at 601bs/sq
2. Slag
To be installed in a flood coat
300 lbs/sq
N/A
Generic
of approved asphalt at 60 lbs/sq
3. KM Acryl 15
A premium white or tinted
1-1%Z gal/sq
ASTM D6083
Polyglass USA,
elastomeric acrylic based roof
Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
4. KM Acryl 15 QS
A premium white or tinted
1-1'/z gal/sq
ASTM D6083
Polyglass USA,
quick setting, elastomeric
Inc,
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
5. KM Acryl 25
A premium white or tinted
1-1'/z gal/sq
ASTM D6083
Polyglass USA,
elastomeric acrylic based roof
Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
6. KM Acryl 25 QS
A premium white or tinted
1-1'/z gal/sq
ASTM D6083
Polyglass USA,
quick setting, elastomeric
Inc,
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
7. KM -PS #220
A single component, solvent,
1.25 gal/sq
ASTM D6694
Polyglass USA,
white or tinted, silicone
Inc.
coating.
8. KM -PS #250
A premium grade high solids,
1.25 gal/sq
ASTM D6694
Polyglass USA,
white or tinted, single
Inc.
component, moisture cure,
fluid applied silicone coating
MIAMFDADE COUNTY
NOA No.: 19-0311.04
• • • • 0 Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 7 of 38
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.
Number Product
Product
Application
Specification
Manufacturer
Name
Description
Rate
9. PG 300
An asphalt cutback fibered roof
1%-2 gal/sq
ASTM D4479
Polyglass USA,
coating. May be applied by
Inc.
brush or spray equipment to
rejuvenate aged BUR
10. PG 600
Non-fibered aluminum roof
%2-1 gal/sq
ASTM D2824
Polyglass USA,
coating.
Type I
Inc.
11. PG 650
Fibered aluminum roof coating.
1'/2-2 gal/sq
ASTM D2824
Polyglass USA,
Type III
Inc.
12. PG 700
A premium white or tinted
1-1'/2 gal/sq
ASTM D6083
Polyglass USA,
elastomeric acrylic based roof
Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
13. PG 700 QS
A premium white or tinted
1-1'/z gal/sq
ASTM D6083
Polyglass USA,
quick setting, elastomeric
Inc.
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
14. PG 800
An asphalt based, non-fibered
3 gal/sq in two
ASTM D1227
Polyglass USA,
clay emulsion
coats
Inc.
15. PolyBrite 70
A premium white or tinted
1-1'/z gal/sq
ASTM D6083
Polyglass USA,
elastomeric acrylic based roof
Inc.
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
16. PolyBrite 70 QS
A premium white or tinted
1-1% gal/sq
ASTM D6083
Polyglass USA,
quick setting, elastomeric
Inc.
acrylic based roof coating
(water -based). A polyester
fabric may be used for
reinforcement with this
coating.
17. PolyBrite 90
A premium grade high solids,
1.25 gal/sq
ASTM D6694
Polyglass USA,
white or tinted, single
Inc.
component, moisture cure,
fluid applied silicone coating
MIAMFDAD, COUNTY
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 8 of 38
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.
Number
Product
Product
Application
Specification
Manufacturer
Name
Description
Rate
18.
PolyBrite 95
A single component, white or
1.25 gal/sq
ASTM D6694
Polyglass USA,
tinted, solvent, moisture cure
Inc.
silicone coating.
19.
POLYPLUS 60
Non-fibered aluminum roof
%-1 gal/sq
ASTM D2824
Polyglass USA,
coating.
Type I
Inc.
20.
POLYPLUS 65
Fibered aluminum roof coating.
1'/Z-2 gal/sq
ASTM D2824
Polyglass USA,
Type III
Inc.
21.
XtraFlex 60 Aluminum
Non-fibered aluminum roof
%-1 gal/sq
ASTM D2824
Polyglass USA,
Roof Coating
coating.
Type I
Inc.
22.
XtraFlex 65 Aluminum
Fibered aluminum roof coating.
1'/z-2 gal/sq
ASTM D2824
Polyglass USA,
Roof Coating Fibered
Type III
Inc.
23.
XtraFlex 70 Premium
A premium white or tinted
1-1 %2 gal/sq
ASTM D6083
Polyglass USA,
Acrylic FR Roof
elastomeric acrylic based roof
Inc.
Coating
coating (water -based). A
polyester fabric may be used
for reinforcement with this
coating.
24.
XtraFlex 80 Emulsion
An asphalt based, non-fibered
3 gal/sq in two
ASTM D 1227
Polyglass USA,
Roof Coating
clay emulsion
coats
Inc.
25.
XtraFlex 30
An asphalt cutback fibered roof
1 %2-2 gal/sq
ASTM D4479
Polyglass USA,
Bituminous Roof
coating. May be applied by
Inc.
Coating Fibered
brush or spray equipment to
rejuvenate aged BUR
26.
XtraFlex SRC 8000
A single component, white or
1.25 gal/sq
ASTM D6694
Polyglass USA,
tinted, solvent, moisture cure
Inc.
silicone coating.
27.
XtraFlex SRC 9600
A premium grade high solids,
1.25 gal/sq
ASTM D6694
Polyglass USA,
white or tinted, single
Inc.
component, moisture cure,
fluid applied silicone coating
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 9 of 38
EVIDENCE SUBMITTED:
Test Agency
Test Name/Report
Report No.
Date
Factory Mutual Research
4470
2W7A7.AM
08.04.94
Corporation
4450
2D5A9.AM
06.22.99
4470
3000857
01.12.00
4470
3004091
01.12.00
4470
3001334
02.15.00
4470
3014692
08.05.03
4450
3014751
08.27.03
4450
3019317
06.30.04
4470
3024311
11.01.06
4470
3012321
07.29.07
4470
3036182
07.31.09
4470
RR202591
10.22.15
Trinity ERD
TAS 114
11752.09.99-1
02.08.00
TAS 114
11751.05.03
05.30.03
TAS 117(B)-ASTM D903
020841.06.04
06.02.04
TAS 114
02762.03.05
03.30.05
TAS 114
02764.09.05
09.09.05
TAS 114
P1739.01.07
01.23.07
TAS 114
P1734.07.06-R1
02.27.07
TAS 117(B)-ASTM D6862
C8500SC.11.07
11.30.07
TAS 114 & FM 4470
P7860SC.11.07
11.30.07
TAS 114(D) — ASTM D 1876
P 10070.10.08
10.09.08
TAS 114 (H)
P13760.09.09
09.10.09
FM 4470 & TAS 114
P33970.03.11
03.15.11
ASTM D6163 / ASTM D 4601
P33960.03.11
03.15.11
ASTM D6163
P37590.03.13-2-R1
02.05.13
ASTM D6164
P37590.03.13-3A
03.06.13
TAS 114
P1738.02.07-R2
04.29.13
TAS 114 & TAS 117 (B)
11757.04.01-1-R1
04.30.13
ASTM D6509
P37590.03.13-1-R1
06.26.13
ASTM D6222
P37590.03.13-5-R1
07.01.13
ASTM D6164
P37590.07.13-1
07.02.13
TAS 114 & FM 4474
P41630.08.13
08.06.13
ASTM D4601 / TAS 117
P45940.09.13
09.04.13
ASTM D6222
P37590.09.13
09.12.13
ASTM D4601 / TAS 117
P45970.05.14
05.12.14
ASTM D6162
SC5170.05.15
05.08.15
ASTM D6162
SC5170.12.15-1
12.29.15
TAS 114 & FM 4474
PLYG-SC8905.05.16-1
05.17.16
TAS 114 & TAS 117 (B)
11757.12.00-1-R2
04.05.17
PRI Construction Materials
ASTM D6222
PUSA-061-02-02
01.28.08
Technologies
ASTM D6163
PUSA-064-02-02
02.27.08
ASTM D6222
PUSA-062-02-02
12.04.08
ASTM D6694
PUSA-134-02-01
05.16.14
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 10 of 38
EVIDENCE SUBMITTED:
Test Agency
Test Name/Report
Report No.
Date
ASTM D6694
PUSA-135-02-01
05.16.14
TAS 117(B)
PUSA-202-02-01
05.08.17
FM 4470 & TAS 114
PUSA-202-02-02
05.23.17
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 11 of 38
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, Elastoshield HT, GAFGLAS 475, Polybond* Polyflex*, Polyglass G2
Base, XtraFlex APP S*, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to
the deck as described below:
*with OMG fasteners and Flat Bottom Metal Plates.
Fastening #1: Attach base sheet using 11 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Fastening #2: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8 plates or Polygrip Fasteners #14 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a
4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft2
Polytherm, Polytherm-H, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-II, ACFoam-III, H-
Shield, Multi -Max FA-3, ENRGY-3
Minimum 1.5" thick
N/A
N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/" thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 12 of 38
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general limitation #7.)
NOA No.: 19-0311.04
MtAMFDADE COUNTY Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 13 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: "/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, Elastoshield HT, Elastobase P, Polybond, Polyflex, Polyglass G2 Base,
XtraFlex APP S, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck
as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft'
Polytherm, Polytherm-H, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-II, ACFoam-III, H-
Shield, Multi -Max FA-3, ENRGY-3
Minimum 1" thick
Top Insulation Laver
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/4" thick
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanu rate side facing down.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 14 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf; (See general limitation #7.)
MIAMFDADE CO
NOA No.: 19-0311.04
. • • M , UNTY Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 15 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below:
Fastening: Attach base sheet using 1 1 ga. Annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
One of more of the following:
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft'
Polytherm, Polytherm-H, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-II, ACFoam-111, H-
Shield, Multi -Max FA-3, ENRGY-3
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft'. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft'
Dens Deck, Dens Deck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/4" thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanu rate side facing down.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS,
(Optional) Elastoflex SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 16 of 38
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FIR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA, XtraFlex SBS G SA,
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 17 of 38
Membrane Type: SBS/APP
Deck Type II: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, Elastoshield HT, Elastobase P XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened as below:
Fastening: 12 ga. Annular ring shank nails and 1-5/8" tin -caps attached 6" o.c. in 4" lap and 6" o.c. in four
equally spaced staggered rows.
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield,
Polytherm-H, H-Shield CG, Multi -Max FA-3, ENRGY 3
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet with Millennium One -Step Foamable Adhesive,
Millennium One Step Green Foamable Insulation Adhesive or Millennium PG-1 Pump Grade Adhesive applied
over rows of tin -caps in continuous rows 7" o.c. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf, (See general limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 18 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C(1):
SBS/APP
Wood, Insulated
Min. 19/32" plywood (15/32" for re -roof) or wood plank, fastened at 24" spans with 8d common
nails at 6" o.c.
All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more of the following
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.0" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Laver
SECUROCK Gypsum -Fiber Roof Board
Minimum '/4" thick
DensDeck Prime
Minimum'/4" thick
Insulation Fasteners Fastener
Table 3 Density/ft'
2 with 4 or 15; 10 with 12; 5 1:2 ft'
with 6, 13 or 14; 7 with 8;
2 with 4; 10 with 12; 5 with 1:2 ft'
6 or 14; 7 with 8;
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P FR, Polyflex SA P FR, Polyfresko G APP SA FR, Polyfresko G
SBS SA FR, PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP SA or XtraFlex
SBS G SA self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 19 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -45 psf; (See General limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 20 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C(2):
SBS/APP
Wood, Insulated
19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails or wood
screws at 4" o.c.
All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more of the following
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5" thick
Note: All layers shall be simultaneously fastened;
panels listed are minimum sizes and dimensions;
increased maintaining the same fastener density.
insulation attachment.
Insulation Fasteners Fastener
Table 3 Density/ft'
N/A N/A
see top layer below for fasteners and density. Insulation
if larger panels are used, the number of fasteners shall be
Please refer to Roofing Application Standard RAS 117 for
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft'
Structodek High Density Fiberboard Roof Insulation
Minimum %z" thick 2 with 4; 10 with 12 1:1.33 ft'
DensDeck
Minimum'/4" thick 2 with 4; 10 with 12 1:1.33 ft'
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft. to DensDeck prior to application of self -adhered base
(Optional) sheets.
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA, XtraFlex SBS G SA,
self -adhered.
MIAMI•DADE COUNTY
NOA No.: 19-0311.04
AP
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 21 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 22 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C(3):
SBS/APP
Wood, Insulated
19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5" thick
Insulation Fasteners Fastener
Table 3 Density/ft'
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Laver
Structodek High Density Fiberboard Roof Insulation
Minimum'/Z" thick
DensDeck
Minimum'/4" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
2 with 4; 10 with 12 1:1.33 ftz
2 with 4; 10 with 12 1:1.33 ft2
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft. to DensDeck prior to application of self -adhered base
(Optional) sheets.
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 23 of 38
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation #7.)
NOA No.: 19-0311.04
MIAMFD,4D; CO� Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 24 of 38
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with wood screws at 6" o.c.
System Type C(4): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following:
Insulation Laver
Insulation Fasteners
Table 3
ENRGY 3, H-Shield, Polytherm-H, ACFoam-II, Polytherm, XtraFlex Polyiso
Minimum 1.5" thick 2 with 4; 7 with 8; 10 with
12
Fastener
Density/ft2
1:1.33 fV
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal. per 300 sq. ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS, Elastoflex SA V
PLUS FR, XtraFlex SBS Base SA, self -adhered.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR or Elastoflex SA V PLUS,
(Optional) Elastoflex SA V PLUS FR, XtraFlex SBS Base SA, self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -82.5 psf; (See General limitation V.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 25 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type D(l):
SBS/APP
Wood, Insulated
19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick
Top Insulation Laver (Optional)
Fesco Board
Minimum 1/" thick
Structodek High Density Fiberboard Roof Insulation
Minimum ''/2" thick
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/4" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
N/A N/A
N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFlex SBS Glass Base
or XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8 plates, Polygrip Fasteners #14 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a
4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 26 of 38
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 27 of 38
Membrane Type:
Deck Type 1I:
Deck Description:
System Type D(2):
SBS/APP
Wood, Insulated
19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick
Top Insulation Laver (Optional)
Fesco Board
Minimum 3/4" thick
Structodek High Density Fiberboard Roof Insulation
Minimum ''/z" thick
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum 1/" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft'
N/A N/A
N/A N/A
N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR, XtraFlex SBS Base SA, self -adhered.
MIAMI•DADE COUNTY
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 28 of 38
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf, (See General limitation #7.)
MIAMPDADE COUNTY
NOA No.: 19-0311.04
• Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 29 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type E(1): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFlex SBS Glass Base
or XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf, (See General limitation #7.).
ML4MFDADE COUNTY
NOA No.: 19-0311.04
• 2 •. Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 30 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32° or greater plywood or wood plank, fastened at 24" spans with 8d ring shank nails at 6"
o.c. at edges and intermediate supports.
System Type E(2): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass APP Base, XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 sheet fastened to the deck as described below:
Fastening: Attach base sheet using I 1 ga. annular grooved shank and 1" diameter caps spaced 6" o.c. in a
3" lap and 6" o.c. in four equally spaced staggered center rows.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf, (See General Limitation #7)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 31 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c
System Type E(3): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, Polyanchor, XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General Limitation #7)
MIAMI•DADE COUNTY
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 32 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General Limitation #7)
CMIAMI•DADE COUNTY NOA No.: 19-0311.04
• r Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 33 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type E(5): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass APP Base, XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 sheet fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8, Polygrip Fasteners #14 with Polygrip Hex Plates or
Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap
and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf, (See General limitation #7.).
C
ADECOUNTY NOA No.: 19-0311.04
• Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 34 of 38
Membrane Type:
Deck Type 1:
SBS/APP
Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. and to blocking
members spaced 48" o.c. with TruFast TP #10x2-7/8" screws spaced 6" o.c.
System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 12 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 4"
o.c. in a 4" lap and 4" o.c. in four equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -97.5 psf; (See General Limitation #7)
MIAMMDADE COUNTY NOA No.: 19-0311.04
• • Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 35 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. and to blocking
members spaced 48" o.c. with #100" wood screws spaced 6" o.c.
System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 12 ga. ring shank nails and tin caps spaced 4" o.c. in a 4" lap and 4"
o.c. in four equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA or XtraFlex SBS G SA
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design -97.5 psf; With Elastoflex SA V or Elastoflex SA V FR (See General limitation #7.)
Pressure: -112.5 psf; With all other base sheet options (See General limitation #7.)
MIAMNDADE CO
NOA No.: 19-0311.04
• UNTY Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 36 of 38
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. with #8x3" wood
screws spaced 6" o.c.
System Type E(8): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 12 ga. annular ring shanked nails and 1-5/8" tin -caps 6" o.c. in 4" lap
and 6" o.c. in four equally spaced staggered rows. Tin -caps are primed with PG 100 or
XtraFlex 10.
Ply Sheet: One or more plies of Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V PLUS, Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self -adhered.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, Polyflex SA P, Polyflex SA P FR, Polyfresko
G APP SA, Polyfresko G APP SA FR, Polyfresko G SBS SA, Polyfresko G SBS SA FR,
PolyKool, Polyreflect, XtraFlex APP G SA, XtraFlex Kool APP S SA, XtraFlex SBS G SA,
self -adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design -97.5 psf; With Elastoflex SA V or Elastoflex SA V FR (See General limitation #7.)
Pressure: -112.5 psf; With all other base sheet options (See General limitation #7.)
NOA No.: 19-0311.04
Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 37 of 38
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 2040 lbs./sq., or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam
insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using
spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one
at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener
spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or
Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS I I I and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
MIAMI•DADE COUNTY
NOA No.: 19-0311.04
• o0 0 Expiration Date: 10/11/22
Approval Date: 03/21/19
Page 38 of 38