HomeMy WebLinkAboutMule-Hide-SA-Base-Sheet-Product-Data-1680771PRODUCT DESCRIPTION
Mule -Hide's SA Base Sheet is a premium fiberglass reinforced, modified bitumen
membrane manufactured to meet the toughest industry and code requirements.
The Mule -Hide SA Base Sheet is manufactured via Adeso"clual-compound
technology, whereby the membrane consists of an Styrene Butadiene Styrene
(SBS) modified asphalt compound on top and a pressure sensitive adhesive
compound on the bottom. The adhesive is covered with a split release liner.
Mule -Hide SA Base Sheet is finished with a polyolefin film with printed lay lines on
the top surface. Meets ASTM D-6163 Type 1, Grade S (smooth) / ASTM D-1970.
BASIC USES
SA Base Sheet membranes are specially designed for applications where the use of hot asphalt, cold process
adhesive, or a propane torch is undesirable. Applications include new rooting, recover (retrofit) and BUR repairs.
Mule -Hide SA Base Sheet can be used as a waterproofing base sheet applied to approved roof decks or
substrates. Do not apply to shingles, shakes or other residential roofing material. See the Mule -Hide Self -
Adhered Modified Bitumen Application Guidelines for complete specifications and details.
SPECIFICATIONS
PRODUCT NAME I r7APPROXVVEIGHT ROLL SIZE ROLL&PALLET COVERAC
in mils Id/roll
s
SA Base Sheet 2.0(80) 95 65'8"x39 3/8° z
120mx1 m1 2D 200 ft
Typical properties and characteristics are based on sampfes tested and are not guaranteed for al/ samples of this product. This data and
information is intended as a guide and does not reflect the specification or specification range for any particular property of this product.
SYSTEM BENEFITS
1. Pre -applied adhesive on the back of the sheet.
2. Lightweight roll sizes.
3. Durable - high performance reinforcement mat.
4. No hot asphalt, fumes or flames required for installation.
5. Excellent long term adhesion to multiple substrates and to base plies.
6. Offers low -temp flexibility, puncture and tear resistance.
CODE APPROVALS
Various code approvals are available including: Factory Mutual, Underwriters Laboratories, Miami -Dade, Florida
Product Approval, ICC-ESR and Texas Department of Insurance. Contact Mule -Hide Technical Department for
specific ratings.
Page 1 of 2
09-1405
Revised July-2015
INSTALLATION INSTRUCTIONS (See complete application instructions)
SA -Base Sheet is intended to be used as a base sheet or interplay in new or re -roofing applications, and requires
the installation of a granulated cap sheet to complete the roofing system.
1. Mule-Hido Nail Base or an approved insulation shall be mechanically attached to a suitable substrate.
1a. Mule -Hide SA Base Sheet may be adhered directly to a suitable substrate.
2. Starting at the low point of the roof, install Mule -Hide SA Cap Sheet as follows: Unroll the SA Cap Sheet and
cut-off approximately 12" from the bottom of the sheet (this will off -set the sheet so that the side laps do not
align, the end laps must be off -set as well.
3. After positioning the sheet, fold the top half of the sheet back lengthwise, remove the release liner and roll the
material back into place, taking care to avoid wrinkles and trapped air, and maintaining proper sheet
alignment.
4. Firmly hand press sheet from the center out avoiding wrinkles and trapped air as the SA Cap Sheet adheres
to the SA Base Sheet,
5. Repeat procedure to adhere remaining half of the sheet.
6. After the sheet is adhered, it is required to be rolled with a 75 lb. roller.
7. Position subsequent sheets to overlap the previous courses by the width of the selvage edge (overlap in a
shingle fashion ensuring that laps are water shedding).
8. Repeat procedures 2 thru 5 above. Remember to remove the release film from the FAS7Lap® and
SEALLapO edges prior to adhering the lower half of the SA cap Sheet. Note: When completing end laps,
cut the top corner of the top sheet on a 45-degree angle (start the cut 3" in from the top edge and finish down
3" from the top edge) and the bottom corner of the bottom sheet on a 45-degree angle (start the cut 3" in from
the bottom edge and finish 3" up from the bottom edge). Apply a solid bead of Mule -Hide Mod Bit Sealant
along both cut edges. Roll entire sheet into place using a 75 lb. roller. Stagger end laps approximately three
feet apart.
This is only a brief summary and NOT the complete specification. The Mule -Hide Self -Adhered Modified Bitumen
Application Guidelines, Specifications, Details, Technical Bulletins, associated documents should be thoroughly
reviewed prior to starting any project.
PROTECTION & SAFETY
Mule -Hide maintains Safety Data Sheets on all of its non exempt products. Safety Data Sheets contain health
and safety information for your development of appropriate product handling procedures to protect your
employees and customers. Mule -Hide's Safety Data Sheets should be read and understood by all of your
supervisory personnel and employees before using Mule -Hide products in your facilities,
ADDITIONAL INFORMATION
The information given on this PDS is subject to change without notice. Always check the Mule -Hide website at
www.mulehide.com for the latest information, changes and updates or contact Mule -Hide Products Company at
800-786-1492.
DISCLAIMER
The statements provided concerning the material shown are intended as a guide for material usage and are believed to be true and accurate
at the time of printing, No statement made by anyone may supersede this information, except when done in writing by Mule -Hide Products
Co., Inc, Since the manner of use is beyond our control, Mule -Hide does not authorize anyone to make any warranty of merchantability or
fitness for any particular purpose or any other warranty, guarantee or representation, expressed or implied, concerning this material. This
product may be eligible for a Mule -Hide warranty, please check the Mule -Hide website at Uvww.mulehide.com or contact Mule -Hide directly at
800-786-1492 for details. Buyer and user accept the product under these conditions and assume the risk of any failure, any injury person or
property (including that of the user), loss or liability resulting from the handling, storage or use of the product whether or not it is handled,
stored or used in accordance with the directions or specifications. Mule -Hide must be notified in writing of any claims and be given the
opportunity to inspect the alleged failure before repairs are made.
Page 2 of 2 09-1405 Revised July-2015