HomeMy WebLinkAboutAPPROVED ROOF INFORMATION SHEET - 5409 PALMETTO DRST. LUCIE
Section A (General Information)
Master Permit No.
Process No.
Contractors Name: �') License # r 7 l7 1
Job Address
ROOF CATEGORY
$Low Slope ❑ Mechanically Fastened Tile ❑ Mortar/Adhesive Set Tiles
sphaltic Shingles ❑ Metal Panel/Shingles ❑Wood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE.
❑ New roof ❑ Repair ❑ Maintenance eroofing ❑ Recovering
�j ROOF SYSTEM INFORMATION .. ! � y�( __
Low Slope Roof Area (SF)L � 1 Steep Sloped Roof Area JSFy (A 11 Total (SF) L
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
F���
ST. LUCIE
Section D (Steep Slope Roof System)
Roof System Manufacturer:
Notice of Acceptance Number:
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1: Zone 2e:----Zone 2n:one zr:- one 3e: Zone 3r:
Deck Type:
\n1a
nt:
Rogf Slope:
12
rier: n ��ld eve lion?tener Type & Spacing: V-) C�
Adhesive Type:
Type Cap Sheet: C�
Mean Roof Height: Roof Covering:
Type & Size trip
Edge:
c\e.t-V
S ■ w LUCIE
Section C (Low Slope Roof)
Filt in specific roof assembly components and identify
manufacturer
(If a component is not , identify as "NA" )
System Manufacturer:�10 �' C A
Product Approval No.: V
Design Wind Pressures, From RAS 128 Or Calculations:
�7 G fir, � C� �y, r. � { 1 Cy
Zone 1 . 0 Zone 1: ` Zone 2:CU -- Zone 3:
Max. Design Pressure, from the specific product approval
system:
Deck:
Type: l
Gauge Thickness: }�
Slope: •V IlCA_l Cj _
Anchor/Base Sheet & No. df Ply(s):
Anchor/ se Sheet Fastener/Bonding Material:
ll � Cl
Insulation Base Layer: Ci ICA,
Base Insultation Size and Thickness: ADL0-
Base insulation Fastener/Bonding Material:
01a
Top Insulation Layer: Y2 GL
Top Insulation Size and Thickness: Y
Top In elation Fastener/Bonding Material:
V-) Ck.
Base Sheet(s) & No. of Ply(s): C
Ba e Sh F�Fastener �onding Ma enal:
r
Piy Sheet(s)' & No. of Ply{s): C
Ply Sheet Fastener/Bonding Material:
Top Ply: ] )C�I k 4 Lam'(
Top Ply Fastener/Bonding Material:
Surfacing: f) I CL
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—" oc @ Lap, # Rows— ® V oc
Zone 1:_" oc @ Lap, # Rows — ® n aC
Zone 2:____" oc @ Lap, # Rows — ®" oa
Zone 3:—" oc @ Lap, f# Rows— a oc
Number of Fasteners Per Insulation Board:
Zone 1': Zone 1: Zone 2• Zone 3:
Illustrate Components Noted and Details as Appiicahte:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterf lashing, Coping, Etc..
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16.