The URL can be used to link to this page

Home My WebLink AboutAPPROVED, 20-0429.10NOA No. 20-0429.10 Expiration Date: March 24, 2025 Approval Date: October 15, 2020 Page 1 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy PGT Industries, Inc. 1070 Technology Drive, North Venice, Fl. 34275 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Series “770HP” Aluminum Sliding Glass Doors w / Reinforcements & 900/1350corners-LMI APPROVAL DOCUMENT: Drawing No.PGT0004 Rev H, titled “Series 770 H.P. Aluminum SGD-LMI”, sheets 1 through 10 of 10, prepared by manufacturer, dated 08/05/07 and last revised on 04/22/20, signed and sealed by Lynn Miller, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami-Dade County Product Control Section. MISSILE IMPACT RATING: Large Missile Impact Resistant Limitations: 1.See tables 1& 1A in sheet 4 of this approved drawing set for applicable SGD unit sizes, design pressures, reinforcements, glass types, sill riser and anchors requirements. See approved configurations in sheet 2. 2. Applicable operable door Egress min clear width & height requirements must comply per FBC, to be reviewed by Building official. 3.See glazing options G4, G4A, G6 and G6A in sheet 3. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and series and following statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA # 19-1126.04 and consists of this page 1 and evidence pages E-1, E-2, E-3 & E-4, as well as approval document mentioned above. The submitted documentation was reviewed by Ishaq I. Chanda, P.E. Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.10 Expiration Date: March 24, 2025 Approval Date: October 15, 2020 E - 1 PGT Industries NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1.Evidence submitted under previous approvals A. DRAWINGS 1. Manufacturer's die drawings and sections (Submitted under files # 11-1018.16/#09-0826.12). 2.Drawing No. PGT0004 Rev D, titled “Series 770 H.P. Aluminum SGD-LMI”, sheets 1 through 10 of 10, prepared by manufacturer, dated 08/05/07 and last revised on 02/13/14, signed and sealed by Lynn Miller, P.E. B. TESTS 1. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC 2411.3.2.1 (b) and TAS 202-94 Along with marked-up drawings and installation diagram of Aluminum Sliding Glass Doors(Samples A-1, A-2, B-1, B-2 and C-1), prepared by Fenestration Testing Laboratory, Inc., Test Report No FTL-7468, dated 09/13/2013, all signed and sealed by Martin D. Brinson, P.E. Note: This test report has addendum letter dated Jan 13, 2014, issued by Fenestration Testing Lab. 2. Test report on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94. 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC 2411.3.2.1 (b) and TAS 202-94 Along with marked-up drawings and installation diagram of Aluminum Sliding Glass Doors, prepared by Fenestration Testing Laboratory, Inc., Test Report No FTL-5998, FTL-6005 and FTL- 6012, dated 08/10/09, all signed and sealed by Julio Gonzales, P.E. (Submitted under files # 11- 1018.16/#09-0826.12) Note: The test reports No. FTL 5998 has been revised and reissued on 12/29/09, signed and sealed by Julio Gonzales, P.E. 3. Additional reference supporting test reports # FTL 5254 and ATI72138.01-401-18. C. CALCULATIONS 1. Anchor verification and comparative analysis dated 01/24/14 and last revised on 02/13/14, sheets 1 thru 45, prepared by PGT, signed and sealed by Lynn Miller, P. E. 2.Glazing complies with ASTME-1300-02 &-04. D. QUALITY ASSURANCE 1.Miami Dade Department of Regulatory and Economic Resources (RER). E.MATERIAL CERTIFICATIONS 1 Notice of Acceptance No. 11-0624.02 issued to E.I. DuPont De Nemours & CO., Inc. for “DuPont SentryGlas ® interlayer”, expiring on 01/14/2017. F.STATEMENTS 1.Statement letter dated OCT 04, 2013 of compliance to FBC 2010 and “No financial interest”, prepared by PGT, signed & sealed by Lynn Miller, P.E. 2.Letter of lab compliance, part of the above test reports Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.10 Expiration Date: March 24, 2025 Approval Date: October 15, 2020 E - 2 PGT Industries NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED G. OTHER 1.This NOA revises # 11-1018.16, expiring March 24, 2015. 2. Test proposal dated 6/4/13 approved by Jaime Gascon, P.E. 3. Test proposals No(s) 09-0177, 0177-A, B & C approved by BCCO. 4.Letter of commitment dated February 20, 2014, issued by PGT, signed by A. Lynn Miller, P.E. 2.Evidence submitted under previous approvals A. DRAWINGS (submitted under file #16-2609.06/#15-0106.07/#13-1009.07) 1.Drawing No. PGT0004, titled “Series 770 H.P. Aluminum SGD – L.M.I.”, sheets 01 through 10 of 10, dated 08/05/07, prepared by manufacturer, revision “F” dated 05/05/16, signed and sealed by Anthony Lynn Miller, P. E. B. TESTS 1.Reference Test report on 1) Uniform Static Air Pressure Test, per FBC, TAS 202-94 2) Large Missile Impact Test per FBC, TAS 201-94 3) Cyclic Wind Pressure Loading per FBC, TAS 203-94 Along with marked-up drawings and installation diagram of Aluminum Sliding Glass Doors (w/ PS, Super, Cardinal & Duraseal Spacers), prepared by Fenestration Testing Laboratory, Inc., Test Reports No(s) FTL-8717, FTL-8970 and FTL-8968, dated 02/15/16, 06/07/16 and 06/20/16, all signed & sealed by Idalmis Ortega, P.E. 2.Test reports on: 1) Air Infiltration Test, per FBC, TAS 202–94 2)Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3)Water Resistance Test, per FBC, TAS 202–94 4) Large Missile Impact Test per FBC, TAS 201–94 5) Cyclic Wind Pressure Loading per FBC, TAS 203–94 6) Forced Entry Test, per FBC 2411.3.2.1, and TAS 202–94 along with marked–up drawings and installation diagram of Aluminum Sliding Glass Door (XOX), prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL–7825, dated 06/10/2014, signed and sealed by Idalmis Ortega, P. E. 3.Test reports on: 1) Air Infiltration Test, per FBC, TAS 202–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3)Water Resistance Test, per FBC, TAS 202–94 4) Large Missile Impact Test per FBC, TAS 201–94 5)Cyclic Wind Pressure Loading per FBC, TAS 203–94 6) Forced Entry Test, per FBC 2411.3.2.1, and TAS 202–94 along with marked–up drawings and installation diagram of Aluminum Sliding Glass Doors (Samples A–1, A–2, B–1, B–2 and C–1), prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL–7468, dated 09/13/2013, signed and sealed by Martin D. Brinson, P. E. C. CALCULATIONS 1.Anchor verification calculations and structural analysis, complying with FBC 5th Addition (2014), prepared by manufacturer, dated 03/05/15, signed and sealed by Anthony Lynn Miller, P.E. 2.Glazing complies with ASTM E1300–04/ 09 D. QUALITY ASSURANCE 1.Miami–Dade Department of Regulatory and Economic Resources (RER). Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.10 Expiration Date: March 24, 2025 Approval Date: October 15, 2020 E - 3 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED E.MATERIAL CERTIFICATIONS 1.Notice of Acceptance No. 14–0916.10 issued to Kuraray America, Inc. for their “Kuraray PVB Glass Interlayer” dated 03/12/15, expiring on 12/11/16. F.STATEMENTS 1.Statement letter of conformance to and complying with FBC 5th Edition (2014), issued by manufacturer, dated 12/31/14, signed and sealed by Anthony Lynn Miller, P. E 2.Test proposal No. 16-0152 dated 03/09/16 approved by RER. 3.Proposals No.’s 09–0177–A, dated 05/05/09, –B, dated 05/27/09 and –C, dated 05/27/09, all issued by the Product Control, signed by Ishaq Chanda, P. E. G. OTHERS 1.Notice of Acceptance No. 15-0106.08, issued to PGT Industries, Inc. for their Series “770–HP Aluminum Sliding Glass Doors w / Reinforcements – L.M.I.”, expiring on 03/24/20. 3. Evidence submitted under previous approval A. DRAWINGS 1.Drawing No. PGT0004 Rev G, titled “Series 770 H.P. Aluminum SGD-LMI”, sheets 1 through 10 of 10, prepared by manufacturer, dated 08/05/07 and last revised on 11/22/19, signed and sealed by Lynn Miller, P.E. B.TESTS (submitted under file #17-0420.13) 1. None C.CALCULATIONS (submitted under file #17-0420.13) 1. None D. QUALITY ASSURANCE 1.Miami Dade Department of Regulatory and Economic Resources (RER). E.MATERIAL CERTIFICATIONS 1.Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. F.STATEMENTS 1.Statement letter of conformance to FBC 2017 (6th Edition) and letter of no financial interest, prepared by PGT, dated 11/22/19, signed and sealed by Lynn Miller, P.E. G. OTHER 1.This NOA renews NOA # 17-0420.13, expiring 03/24/ 2025. 4.New Evidence submitted A. DRAWINGS 1.Drawing No. PGT0004 Rev H, titled “Series 770 H.P. Aluminum SGD-LMI”, sheets 1 through 10 of 10, prepared by manufacturer, dated 08/05/07 and last revised on 04/22/20, signed and sealed by Lynn Miller, P.E. Ishaq I. Chanda, P.E. Product Control Unit Supervisor NOA No. 20-0429.10 Expiration Date: March 24, 2025 Approval Date: October 15, 2020 E - 4 PGT Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED B. TESTS 1.Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4)Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along with marked-up drawings and installation diagram of all PGT Industries, Inc. representative units listed below and tested to qualify Dowsil 791 and Dowsil 983 silicones, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.: FTL-7897, PGT PW5520 PVC Fixed Window (unit 6 in proposal), dated 09/03/14 FTL-20-2107.1, PGT SGD780 Aluminum Sliding Glass Door (unit 7 in proposal) FTL-20-2107.2, PGT CA740 Alum. Outswing Casement Window (unit 8 in proposal) FTL-20-2107.3, PGT PW7620A Aluminum Fixed Window (unit 9 in proposal) and FTL-20-2107.4, PGT PW7620A Aluminum Fixed Window (unit 10 in proposal) dated 07/13/20, all signed and sealed by Idalmis Ortega, P.E. C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 7th Edition (2020), dated 04/20/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2.Glazing complies with ASTM E1300-04, -09, -12 and -16. D.QUALITY ASSURANCE 1.Miami Dade Department of Regulatory and Economic Resources (RER). E.MATERIAL CERTIFICATIONS 1.Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. F.STATEMENTS 1.Statement letters of conformance to FBC 2020(7th Edition), dated 04/20/20, prepared, signed & sealed by Lynn Miller, P. E. G. OTHER 1.This NOA revises NOA #19-1126.04 and updates FBC 2020 (7th Edition), expiring 03/24/25. 2.RER Test proposals #19-1155 dated 01/10/20 approved by Ishaq I. Chanda, P.E, expiring 04/14/21expiring 04/07/25. PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control PRODUCT REVISED as complying with the Florida Building Code NOA–No. 20-0429.10 Expiration Date: 03/24/2025 By: ____________________________ Miami–Dade Product Control