The URL can be used to link to this page

Home My WebLink AboutPIR56mm Roll Shutter Customer Marotta, Peter Job Name:Marotta, Peter Order Date:10/ Unit Name:1-(1 of 1)Finished Weight:119.00 lbs.Tube Size:70 Finished Width:92 in.Finished Height:93 in.Hood Size:1 Slat Color:White Total sqft:59.42 Slat Style:V Frame Color:White Time (hours):2.38 Safety Plates: Operation (Choose):Hybrid w/ Override 50Nm Position:(1) 45 Degree Hood Style:B Operation Side (Choose):(B) Front Right Slat Hangers: Hood Length:91 1/2 in.Done By Checked by Initals Date Initals Statu I. Cutting and Preparing Dimensions # to cut Color Hood Face 91 1/2 in.1 White Hood Back 91 1/2 in.1 White Motor Tube 88 3/4 in.1 Slat Hangers 56mm 5 White Main Slats (Vented )86 1/2 in.39 White End Retention Side Rails 83 in.2 White Pre-Drill Side Rails.Spacing - 6.0 inches 1 pair entry guides AC01-12A Insert Felt into Side Rails Crimp felt in retention Side Rail Product Approval Sticker 1 Put hole caps in bag 28 Bubble wrap Retention side rails with hole caps II. Assembly Assemble Slat Curtain. Insert slat Gasket. Trim Flush. Attach Conic Stoppers FBC Sticker 1 Secure end retention caps on top 5 and bottom 5 slats and every other slat inbetween using 1 White 3/16" rivets. Attach connector slats to curtain Rivet Connector Slat to Motor Tube.with 3/16" rivets In the Motor Tube, Install Hybrid w/ Override 50Nm (B) Front Right Motor Mounting Plate AC03-0802 Operator Part Number TMRS45M-50/12 If Motorized, SERIAL #: Idle Bearing Cradle AC03-40 On the opposite side of Motor Tube, Install the Idle Bearing AC02-05-110 Install screw or pin in idle bearing Install Left Side Cap CA03-250WH L Install Right Side Cap CA03-250WH R Drill hole for crank extension if needed Position:(1) 45 Degree Roll Slat Curtain with Plastic. Secure with Tape. Install Hood Back with 4 - 3/16" White rivets Install Hood Front III. Packing Electrical: Bubble wrap shutter Pack shutter in tube Pack Side Rails with hole caps in tube Pack picked parts in tube Installation instruction To be completed by Quality Inspector Only. Fabricator is not to write anything below this line. Quality Inspector Signature: Date: Done ON TIME? □ Yes □ No If no, specifiy how late and WHY below. Submit Deviation Report. 100% Correct upon Inspection □ Yes □ No If no, specifiy what was incorrect below. Submit Deviation Report. Felt:4 x 83 in.AC01-10 Gasket Length:86 1/2 in.AC01-17 Rubber Rings:0 Hole Caps:28 AC01-11 SideCap RH:1 Number of Slats:39 EX01-01 SideCap LH:1 Pieces per slat:3 Slat Length:24 ft. Slat Cap pairss:ACO1-08 Drop:28 1/2 in. 1 Wing End Ret. Pairs:10 AC06-01/1 2 Wing End Ret. Pairs:15 AC06-02/1 Roll Diameter:8.0000 in. 56mm Roll Shutter Customer Marotta, Peter Job Name:Marotta, Peter Order Date:10/ Unit Name:2-(1 of 1)Finished Weight:135.00 lbs.Tube Size:70 Finished Width:104 1/2 in.Finished Height:93 in.Hood Size:1 Slat Color:White Total sqft:67.49 Slat Style:V Frame Color:White Time (hours):2.70 Safety Plates: Operation (Choose):Hybrid w/ Override 50Nm Position:(1) 45 Degree Hood Style:B Operation Side (Choose):(A) Front Left Slat Hangers: Hood Length:104 in.Done By Checked by Initals Date Initals Statu I. Cutting and Preparing Dimensions # to cut Color Hood Face 104 in.1 White Hood Back 104 in.1 White Motor Tube 101 1/4 in.1 Slat Hangers 56mm 6 White Main Slats (Vented )99 in.39 White End Retention Side Rails 83 in.2 White Pre-Drill Side Rails.Spacing - 6.0 inches 1 pair entry guides AC01-12A Insert Felt into Side Rails Crimp felt in retention Side Rail Product Approval Sticker 1 Put hole caps in bag 28 Bubble wrap Retention side rails with hole caps II. Assembly Assemble Slat Curtain. Insert slat Gasket. Trim Flush. Attach Conic Stoppers FBC Sticker 1 Secure end retention caps on top 5 and bottom 5 slats and every other slat inbetween using 1 White 3/16" rivets. Attach connector slats to curtain Rivet Connector Slat to Motor Tube.with 3/16" rivets In the Motor Tube, Install Hybrid w/ Override 50Nm (A) Front Left Motor Mounting Plate AC03-0802 Operator Part Number TMRS45M-50/12 If Motorized, SERIAL #: Idle Bearing Cradle AC03-40 On the opposite side of Motor Tube, Install the Idle Bearing AC02-05-110 Install screw or pin in idle bearing Install Left Side Cap CA03-250WH L Install Right Side Cap CA03-250WH R Drill hole for crank extension if needed Position:(1) 45 Degree Roll Slat Curtain with Plastic. Secure with Tape. Install Hood Back with 4 - 3/16" White rivets Install Hood Front III. Packing Electrical: Bubble wrap shutter Pack shutter in tube Pack Side Rails with hole caps in tube Pack picked parts in tube Installation instruction To be completed by Quality Inspector Only. Fabricator is not to write anything below this line. Quality Inspector Signature: Date: Done ON TIME? □ Yes □ No If no, specifiy how late and WHY below. Submit Deviation Report. 100% Correct upon Inspection □ Yes □ No If no, specifiy what was incorrect below. Submit Deviation Report. Felt:4 x 83 in.AC01-10 Gasket Length:99 in.AC01-17 Rubber Rings:0 Hole Caps:28 AC01-11 SideCap RH:1 Number of Slats:39 EX01-01 SideCap LH:1 Pieces per slat:2 Slat Length:24 ft. Slat Cap pairss:ACO1-08 Drop:90 in. 1 Wing End Ret. Pairs:10 AC06-01/1 2 Wing End Ret. Pairs:15 AC06-02/1 Roll Diameter:8.0000 in. 56mm Roll Shutter Customer Marotta, Peter Job Name:Marotta, Peter Order Date:10/ Unit Name:3-(1 of 1)Finished Weight:136.00 lbs.Tube Size:70 Finished Width:105 1/2 in.Finished Height:93 in.Hood Size:1 Slat Color:White Total sqft:68.14 Slat Style:V Frame Color:White Time (hours):2.73 Safety Plates: Operation (Choose):Hybrid w/ Override 50Nm Position:(1) 45 Degree Hood Style:B Operation Side (Choose):(B) Front Right Slat Hangers: Hood Length:105 in.Done By Checked by Initals Date Initals Statu I. Cutting and Preparing Dimensions # to cut Color Hood Face 105 in.1 White Hood Back 105 in.1 White Motor Tube 102 1/4 in.1 Slat Hangers 56mm 6 White Main Slats (Vented )100 in.39 White End Retention Side Rails 83 in.2 White Pre-Drill Side Rails.Spacing - 6.0 inches 1 pair entry guides AC01-12A Insert Felt into Side Rails Crimp felt in retention Side Rail Product Approval Sticker 1 Put hole caps in bag 28 Bubble wrap Retention side rails with hole caps II. Assembly Assemble Slat Curtain. Insert slat Gasket. Trim Flush. Attach Conic Stoppers FBC Sticker 1 Secure end retention caps on top 5 and bottom 5 slats and every other slat inbetween using 1 White 3/16" rivets. Attach connector slats to curtain Rivet Connector Slat to Motor Tube.with 3/16" rivets In the Motor Tube, Install Hybrid w/ Override 50Nm (B) Front Right Motor Mounting Plate AC03-0802 Operator Part Number TMRS45M-50/12 If Motorized, SERIAL #: Idle Bearing Cradle AC03-40 On the opposite side of Motor Tube, Install the Idle Bearing AC02-05-110 Install screw or pin in idle bearing Install Left Side Cap CA03-250WH L Install Right Side Cap CA03-250WH R Drill hole for crank extension if needed Position:(1) 45 Degree Roll Slat Curtain with Plastic. Secure with Tape. Install Hood Back with 4 - 3/16" White rivets Install Hood Front III. Packing Electrical: Bubble wrap shutter Pack shutter in tube Pack Side Rails with hole caps in tube Pack picked parts in tube Installation instruction To be completed by Quality Inspector Only. Fabricator is not to write anything below this line. Quality Inspector Signature: Date: Done ON TIME? □ Yes □ No If no, specifiy how late and WHY below. Submit Deviation Report. 100% Correct upon Inspection □ Yes □ No If no, specifiy what was incorrect below. Submit Deviation Report. Felt:4 x 83 in.AC01-10 Gasket Length:100 in.AC01-17 Rubber Rings:0 Hole Caps:28 AC01-11 SideCap RH:1 Number of Slats:39 EX01-01 SideCap LH:1 Pieces per slat:2 Slat Length:24 ft. Slat Cap pairss:ACO1-08 Drop:88 in. 1 Wing End Ret. Pairs:10 AC06-01/1 2 Wing End Ret. Pairs:15 AC06-02/1 Roll Diameter:8.0000 in. 56mm Roll Shutter Customer Marotta, Peter Job Name:Marotta, Peter Order Date:10/ Unit Name:4-(1 of 1)Finished Weight:137.00 lbs.Tube Size:70 Finished Width:106 in.Finished Height:93 in.Hood Size:1 Slat Color:White Total sqft:68.46 Slat Style:V Frame Color:White Time (hours):2.74 Safety Plates: Operation (Choose):Hybrid w/ Override 50Nm Position:(1) 45 Degree Hood Style:B Operation Side (Choose):(A) Front Left Slat Hangers: Hood Length:105 1/2 in.Done By Checked by Initals Date Initals Statu I. Cutting and Preparing Dimensions # to cut Color Hood Face 105 1/2 in.1 White Hood Back 105 1/2 in.1 White Motor Tube 102 3/4 in.1 Slat Hangers 56mm 6 White Main Slats (Vented )100 1/2 in.39 White End Retention Side Rails 83 in.2 White Pre-Drill Side Rails.Spacing - 6.0 inches 1 pair entry guides AC01-12A Insert Felt into Side Rails Crimp felt in retention Side Rail Product Approval Sticker 1 Put hole caps in bag 28 Bubble wrap Retention side rails with hole caps II. Assembly Assemble Slat Curtain. Insert slat Gasket. Trim Flush. Attach Conic Stoppers FBC Sticker 1 Secure end retention caps on top 5 and bottom 5 slats and every other slat inbetween using 1 White 3/16" rivets. Attach connector slats to curtain Rivet Connector Slat to Motor Tube.with 3/16" rivets In the Motor Tube, Install Hybrid w/ Override 50Nm (A) Front Left Motor Mounting Plate AC03-0802 Operator Part Number TMRS45M-50/12 If Motorized, SERIAL #: Idle Bearing Cradle AC03-40 On the opposite side of Motor Tube, Install the Idle Bearing AC02-05-110 Install screw or pin in idle bearing Install Left Side Cap CA03-250WH L Install Right Side Cap CA03-250WH R Drill hole for crank extension if needed Position:(1) 45 Degree Roll Slat Curtain with Plastic. Secure with Tape. Install Hood Back with 4 - 3/16" White rivets Install Hood Front III. Packing Electrical: Bubble wrap shutter Pack shutter in tube Pack Side Rails with hole caps in tube Pack picked parts in tube Installation instruction To be completed by Quality Inspector Only. Fabricator is not to write anything below this line. Quality Inspector Signature: Date: Done ON TIME? □ Yes □ No If no, specifiy how late and WHY below. Submit Deviation Report. 100% Correct upon Inspection □ Yes □ No If no, specifiy what was incorrect below. Submit Deviation Report. Felt:4 x 83 in.AC01-10 Gasket Length:100 1/2 in.AC01-17 Rubber Rings:0 Hole Caps:28 AC01-11 SideCap RH:1 Number of Slats:39 EX01-01 SideCap LH:1 Pieces per slat:2 Slat Length:24 ft. Slat Cap pairss:ACO1-08 Drop:87 in. 1 Wing End Ret. Pairs:10 AC06-01/1 2 Wing End Ret. Pairs:15 AC06-02/1 Roll Diameter:8.0000 in.