The URL can be used to link to this page

Home My WebLink AboutAPPROVED NOA ALL MULLS 20111813 (2) NOA No. 20-1118.13 Expiration Date: September 16, 2024 Approval Date: February 18, 2021 2/5/21 Page 1 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/building E.S. Windows, LLC 3550 NW 49th Street Miami, FL 33142 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami–Dade County RER– Product Control Section to be used in Miami–Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami–Dade County Product Control Section (In Miami–Dade County) and/ or the AHJ (in areas other than Miami–Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance if it is determined by Miami–Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Clipped, Extruded Aluminum Tube Mullion – L.M.I. APPROVAL DOCUMENT: Drawing No. M04-04, titled “Aluminum Tube Mullions”, sheets 1 through 9 of 9, dated 04/26/04, with revision I dated 11/05/20, prepared by Al-Farooq Corporation, signed and sealed by Jalal Farooq, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami-Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, Barranquilla, Colombia, model/series, and following statement: "Miami–Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami–Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No. 19-0405.10 and consists of this page 1 and evidence pages E-1, E-2 and E-3, as well as approval document mentioned above. The submitted documentation was reviewed by Manuel Perez, P.E. Manuel Perez, P.E. Product Control Examiner NOA No. 20-1118.13 Expiration Date: September 16, 2024 Approval Date: February 18, 2021 E – 1 E.S. Windows, LLC NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s A. DRAWINGS 1. Manufacturer's die drawings and sections. (Submitted under NOA No. 04-0712.01) 2. Drawing No. M04-04, titled “Aluminum Tube Mullions”, sheets 1 through 9 of 9, dated 04/26/04, with revision H dated 01/17/18, prepared by Al-Farooq Corporation, signed and sealed by Javad Ahmad, P.E. (Submitted under NOA No. 18-0205.05) B. TESTS 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, Type “D-A” fixed window, Grade 10, Level LV 1 per ASTM F 588-04, Side-Hinged Door Systems per AAMA 1304- 02 and per FBC 2411.3.2.1, TAS 202-94 along with marked-up drawings and installation diagram of windows mulled together, prepared by Fenestration Testing Laboratory, Inc., Test Reports No. FTL-3810, dated 05/16/03; FTL-3819, dated 06/09/03 and FTL-3820, dated 06/09/03, all signed and sealed by Joseph Chan, P.E. (Submitted under NOA No. 04-0712.01) C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 6th Edition (2017), dated 01/12/18, prepared by Al-Farooq Corporation, signed and sealed by Javad Ahmad, P.E. (Submitted under NOA No. 18-0205.05) 2. Glazing complies with ASTM E1300-09 D. QUALITY ASSURANCE 1. Miami-Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. None. Manuel Perez, P.E. Product Control Examiner NOA No. 20-1118.13 Expiration Date: September 16, 2024 Approval Date: February 18, 2021 E – 2 E.S. Windows, LLC NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s (CONTINUED) F. STATEMENTS 1. Statement letter of conformance, complying with FBC 6th Edition (2017), dated March 28, 2019, issued by Al-Farooq Corporation, signed and sealed by Javad Ahmad, P.E. (Submitted under NOA No. 19-0405.10) 2. Laboratory compliance letter for Test Reports No. FTL-3810, dated 05/16/03; FTL-3819, dated 06/09/03 and FTL-3820, dated 06/09/03, all issued by Fenestration Testing Laboratory, Inc. and all signed and sealed by Joseph C. Chan, P.E. (Submitted under NOA No. 04-0712.01) G. OTHERS 1. Notice of Acceptance No. 18-0205.05, issued to ES Windows, LLC for their Clipped, Extruded Aluminum Tube Mullion – L.M.I., approved on 03/08/18 and expiring on 09/16/19. Manuel Perez, P.E. Product Control Examiner NOA No. 20-1118.13 Expiration Date: September 16, 2024 Approval Date: February 18, 2021 E - 3 E.S. Windows, LLC NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 2. NEW EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. M04-04, titled “Aluminum Tube Mullions”, sheets 1 through 9 of 9, dated 04/26/04, with revision I dated 11/05/20, prepared by Al-Farooq Corporation, signed and sealed by Jalal Farooq, P.E. B. TESTS 1. None. C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 6th Edition (2017), dated 01/12/18, and updated on 11/04/20 to comply with FBC 7th Edition (2020), prepared by Al-Farooq Corporation, signed and sealed by Jalal Farooq, P.E. 2. Glazing complies with ASTM E1300-09 D. QUALITY ASSURANCE 1. Miami-Dade Department of Regulatory and Economic Resources (RER) E. MATERIAL CERTIFICATIONS 1. None. F. STATEMENTS 1. Statement letter of conformance, complying with FBC 6th Edition (2017), with FBC 7th Edition (2020), and of no financial interest, dated November 4, 2020, issued by Al-Farooq Corporation, signed and sealed by Jalal Farooq, P.E. G. OTHERS 1. Notice of Acceptance No. 19-0405.10, issued to E.S. Windows, LLC for their Clipped, Extruded Aluminum Tube Mullion – L.M.I., approved on 05/30/19 and expiring on 09/16/24.