Press Alt + R to read the document text or Alt + P to download or print.

No preview available

The URL can be used to link to this page

Home My WebLink AboutFL1654_R28_AE_2021_06_09_FINAL_ER_PG_MODBIT_FL1654-R28 NEMO|etc. Certificate of Authorization #32455 353 Christian Street, Unit #13 Oxford, CT 06478 (203) 262-9245 ENGINEER EVALUATE TEST CONSULT EVALUATION REPORT Polyglass USA, Inc. 1111 West Newport Center Drive Deerfield Beach, FL 33442 (954) 233-1330 Evaluation Report P9290.02.08-R26 FL1654-R28 Date of Issuance: 02/11/2008 Revision 26: 06/09/2021 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product descr ibed herein has been evaluated for compliance with the 7th Edition (2020) Florida Building Code sections noted herein. DESCRIPTION: Polyglass Modified Bitumen Roof Systems for use in FBC non-HVHZ jurisdictions LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change. Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any changes to the product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words “NEMO|etc. Evaluated” may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manuf acturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 5, plus a 98-page Appendix. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 06/09/2021. This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. NEMO ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing produ cts for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. ©2018, NEMO ETC, LLC NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION FL1654-R28 Polyglass Modified Bitumen Roof Systems Revision 26: 06/09/2021 Page 2 of 5 ROOFING SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub-Category: Modified Bitumen Roof Systems Compliance Statement: Polyglass Modified Bitumen Roof Systems, as produced by Polyglass USA, Inc., have demonstrated compliance with the following sections of the 7th Edition (2020) Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Section Property Standard Year 1504.3.1 Wind resistance FM 4474 2011 1504.3.1 Wind resistance UL 1897 2012 1504.6 Accelerated weathering ASTM G155 2013 1504.7 Impact resistance FM 4470, Section 4.6 2016 1507.10.2 Material standard ASTM D4601 2012 1507.10.2 Material standard ASTM D4897 2009 1507.11.2 Material standard ASTM D6162 2015 1507.11.2 Material standard ASTM D6163 2015 1507.11.2 Material standard ASTM D6164 2011 1507.11.2 Material standard ASTM D6222 2011 1507.11.2 Material standard ASTM D6509 2015 3. REFERENCES: Entity Exam Reference Date Entity Exam Reference Date ERD (TST11294) FM 4470/4474 PLYG-CTL13945.05.17-1 5/30/2017 FM (TST1867) FM 4470 3020703 7/30/2004 ERD (TST11294) FM 4470/4474 PLYG-CTL13945.05.17-3 5/30/2017 FM (TST1867) FM 4470/4474 3018332 1/31/2006 ERD (TST6049) FM 4470/4474 P13760.09.09 9/10/2009 FM (TST1867) FM 4470/4474 3023368 3/20/2006 ERD (TST6049) FM 4470/4474 P13770.09.09 9/10/2009 FM (TST1867) FM 4470/4474 3024594 5/23/2006 ERD (TST6049) FM 4470/4474 P30540.11.09-R1 11/30/2009 FM (TST1867) FM 4470/4474 3023458 7/18/2006 ERD (TST6049) FM 4470/4474 P30550.12.09 12/2/2009 FM (TST1867) FM 4470/4474 3030668 9/12/2007 ERD (TST6049) FM 4470/4474 P33970.03.11 3/15/2011 FM (TST1867) FM 4470/4474 3032172 6/12/2009 ERD (TST6049) D6163 P33960.03.11 3/15/2011 FM (TST1867) FM 4470/4474 3049631 4/21/2014 ERD (TST6049) D6509 P37590.03.13-1-R1 2/5/2013 FM (TST1867) FM 4470/4474 3057029 2/2/2017 ERD (TST6049) D6163 P37590.03.13-2-R1 2/5/2013 FM (TST1867) FM 4470 3001334 1/25/2000 ERD (TST6049) D6222 P37590.03.13-5-R1 2/6/2013 FM (TST1867) FM 4470 3014751 8/27/2003 ERD (TST6049) FM 4470/4474 P39680.03.13 3/4/2013 FM (TST1867) FM 4470 3007170 1/13/2004 ERD (TST6049) D6164 P37590.03.13-3A 3/6/2013 NEMO (TST6049) Criticality 4S-PLYG-18-001.06.18 6/23/2018 ERD (TST6049) D6164 / G155 P37590.07.13-1 7/2/2013 NEMO (TST6049) FM 4474 4L-PLYG-18-003.08.18 8/21/2018 ERD (TST6049) FM 4470/4474 P41630.08.13 8/6/2013 NEMO (TST6049) Criticality 4S-PLYG-18-001.10.18 10/3/2018 ERD (TST6049) D4601 P45940.09.13 9/4/2013 NEMO (TST6049) D4897 4S-PLYG-18-002.11.18-2 11/16/2018 ERD (TST6049) D4601 P44370.10.13 10/4/2013 NEMO (TST6049) FM 4474 4L-PLYG-18-003.11.18 11/28/2018 ERD (TST6049) D6163 (Table 2) P33960.05.14 5/8/2014 NEMO (TST6049) D6164 4S-PLYG-18-002.11.18-3 11/28/2018 ERD (TST6049) D6164 / G155 P35660.10.14 10/3/2014 NEMO (TST6049) FM 4474 4L-PLYG-18-003.01.19 1/11/2019 ERD (TST6049) FM 4470/4474 SC6160.11.14 11/10/2014 NEMO (TST6049) D6163 4S-PLYG-18-002.01.19-A 1/24/2019 ERD (TST6049) D6163 / G155 P45440SC.03.15-1 3/31/2015 NEMO (TST6049) D6162 / G155 4S-PLYG-18-002.01.19-B 1/25/2019 ERD (TST6049) D6163 / G155 P45440SC.03.15-2-R1 3/31/2015 NEMO (TST6049) Criticality 2i-PLYG-19-SSCRT-01.A 2/6/2019 ERD (TST6049) D6162 SC5170.05.15 5/8/2015 NEMO (TST6049) FM 4474 4L-PLYG-18-003.04.19-A 4/8/2019 ERD (TST6049) FM 4474 SC8085.05.15 5/19/2015 NEMO (TST6049) D6163 4S-PLYG-18-002.05.19-H 5/20/2019 ERD (TST6049) D6162 SC5170.12.15 12/29/2015 NEMO (TST6049) D6222 / G155 4S-PLYG-18-002.05.19-C 5/20/2019 ERD (TST6049) FM 4470/4474 SC9455.15 4/1/2016 NEMO (TST6049) D6222 / G155 4S-PLYG-18-002.05.19-D 5/20/2019 ERD (TST6049) FM 4470/4474 PLYG-SC8905.05.16-1 5/17/2016 NEMO (TST6049) D6164 4S-PLYG-18-002.05.19-N 5/31/2019 ERD (TST6049) FM 4470/4474 PLYG-SC8905.05.16-2 5/17/2016 NEMO (TST6049) Criticality 4S-PLYG-18-001.06.19.A 7/17/2019 ERD (TST6049) FM 4470/4474 PLYG-SC10815.07.16-R1 9/23/2016 NEMO (TST6049) D6164 4S-PLYG-18-002.08.19-I 9/6/2019 ERD (TST6049) UL 1897 PLYG-SC12025.10.16 10/12/2016 NEMO (TST6049) D6164 / G155 4S-PLYG-18-002.09.19-J 9/6/2019 ERD (TST6049) FM 4470/4474 PLYG-SC11475.16 11/17/2016 NEMO (TST6049) FM 4474 4a-ICP-19-LSWUS-01.A 11/8/2019 ERD (TST6049) FM 4470/4474 PLYG-SC13235.01.17 1/17/2017 NEMO (TST6049) D4601 4q-PLYG-19-SSMBB-02.A 12/13/2019 ERD (TST6049) FM 4470/4474 PLYG-SC13920.05.17 5/30/2017 NEMO (TST6049) D6164 4q-PLYG-19-SSMBB-04.A 1/2/2020 ERD (TST6049) FM 4470/4474 PLYG-SC13945.05.17 5/30/2017 NEMO (TST6049) D6164 / G155 4q-PLYG-19-SSMBB-04.B 1/2/2020 ERD (TST6049) FM 4470/4474 PLYG-SC15760.09.17 9/11/2017 NEMO (TST6049) D6222 / G155 4q-PLYG-19-SSMBB-05.A 7/23/2020 FM (TST1867) FM 4470 2W7A7.AM 8/4/1994 NEMO (TST6049) FM 4474 4a-PLYG-20-LSWUS-01.A 8/28/2020 FM (TST1867) FM 4470 0D3A3.AM 4/4/1997 NEMO (TST6049) FM 4474 4a-PLYG-20-LSWUS-02.A 10/5/2020 FM (TST1867) FM 4470 2D0A0.AM 12/23/1998 NEMO (TST6049) D6164 4q-PLYG-20-SSMBB-04.A 10/21/2020 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION FL1654-R28 Polyglass Modified Bitumen Roof Systems Revision 26: 06/09/2021 Page 3 of 5 Entity Exam Reference Date Entity Exam Reference Date FM (TST1867) FM 4470 2D5A9.AM 6/22/1999 NEMO (TST6049) FM 4474 4a-PLYG-21-LSWUS-01.A 6/7/2021 FM (TST1867) FM 4470 3006646 1/4/2000 NEMO (TST6049) Criticality 4i-PLYG-21-LSWUS-02.A 6/7/2021 FM (TST1867) FM 4470 3000857 1/12/2000 PRI (TST5878) TAS 114 PUSA-188-02-01 2/8/2017 FM (TST1867) FM 4470 3004091 1/12/2000 PRI (TST5878) TAS 114 PUSA-188-02-02 2/8/2017 FM (TST1867) FM 4470 3001334 2/15/2000 PRI (TST5878) TAS 114 PUSA-188-02-03 2/8/2017 FM (TST1867) FM 4470 3006115 5/2/2001 PRI (TST5878) TAS 114 PUSA-202-02-01 5/17/2017 FM (TST1867) FM 4470 3012321 7/29/2002 PRI (TST5878) TAS 114 PUSA-202-02-02 5/17/2017 FM (TST1867) FM 4470 3014692 8/5/2003 M-D (CER1592) Prop. for Rev. 10-0823 10/12/2010 FM (TST1867) FM 4470 3019317 6/30/2004 UL (QUA9625) Quality Control Service Confirm 9/13/2018 UL (QUA9625) Quality Control Florida BCIS Current 4. PRODUCT DESCRIPTION: This Evaluation Report covers Polyglass Modified Bitumen Roof Systems installed in accordance with Polyglass USA, Inc. published installation instructions and the Limitations / Conditions of Use herein. TABLE 1: EVALUATED MEMBRANES Type Product Material Standard Plant(s) Reference Type Grade Base Sheets Polyglass G2 Base ASTM D4601 II N/A AL Polyflex SA Base ASTM D4601 II N/A FL Elastobase SA ASTM D4601 II N/A PA Elastovent ASTM D4897 N/A N/A PA Polybase V (formerly “Polyglass Base”) ASTM D6509 N/A N/A FL APP, Smooth- Surface Membranes Polybond ASTM D6222 I S FL Polyflex ASTM D6222 I S FL APP, Granule- Surface Membranes Polybond G ASTM D6222 I G FL Polyflex G ASTM D6222 I G FL Polyflex G FR ASTM D6222 I G FL Polyfresko G ASTM D6222 I G NV Polyfresko G FR ASTM D6222 I G NV Polyflex SA P ASTM D6222 I G FL, TX Polyflex SA P FR ASTM D6222 I G TX Polyfresko G SA ASTM D6222 I G NV Polyfresko G SA FR ASTM D6222 I G NV SBS, Smooth- Surface Membranes Elastoshield VP HT (formerly “Elastoshield HT”) ASTM D6162 III S FL, PA Elastobase V (formerly “Elastobase”) ASTM D6163 I S FL Elastoflex V ASTM D6163 I S FL Elastoflex SA V ASTM D6163 I S FL, PA, TX Elastoflex SA V FR ASTM D6163 I S FL, PA, TX Elastoflex SA V Plus ASTM D6163 I S FL, TX Elastoflex SA V Plus FR ASTM D6163 I S FL, TX Elastobase P ASTM D6164 I S FL, TX Elastoflex SA Base HD ASTM D6164 I S PA, TX Elastoflex S6 ASTM D6164 I S FL Elastoshield TS ASTM D6164 I S PA Elastoflex S6 HP ASTM D6164 II S NV Polyreflect ASTM D6164 I S FL NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION FL1654-R28 Polyglass Modified Bitumen Roof Systems Revision 26: 06/09/2021 Page 4 of 5 TABLE 1 (CONTINUED): EVALUATED MEMBRANES Type Product Material Standard Plant(s) Reference Type Grade SBS, Granule Surface Membranes Elastoshield HT G ASTM D6162 III G FL Elastoshield HT G FR ASTM D6162 III G FL Elastoflex V G ASTM D6163 I G FL, PA Elastoflex V G FR ASTM D6163 I G FL, PA Elastoflex S6 G ASTM D6164 I G FL, PA Elastoflex S6 G FR ASTM D6164 I G FL Elastoshield TS G ASTM D6164 I G FL, TX Elastoshield TS G FR ASTM D6164 I G FL, TX Elastoflex SA P ASTM D6164 I G FL, TX Elastoflex SA P FR ASTM D6164 I G FL, TX 5. LIMITATIONS: 5.1 This is a Building Code Evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC High Velocity Hurricane Zone jurisdictions (i.e., Broward and Miami-Dade Counties). 5.3 This Evaluation Report pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. 5.4 This Evaluation Report does not include evaluation of fire classificat ion. Refer to FBC 1505 for requirements and limitations regarding roof assembly fire classification. Refer to FBC 2603 for requirements and limitations concerning the use of foam plastic insulation. 5.5 This Evaluation Report does not include evaluation of roof edge termination. Refer to FBC 1504.5 for requirements and limitations regarding edge securement for low -slope roofs. 5.6 Refer to FBC 1511 for requirements and limitations regarding recover installations. 5.6.1 For mechanically attached components over existing roof decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard TAS 105. 5.6.2 For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question, field uplift testing in accordance with ANSI/SPRI IA- 1, ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124 shall be conducted on mock-ups of the proposed new roof assembly. 5.6.3 For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction, as documented through field uplift testing in accordance with ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124. 5.7 Refer to Appendix 1 for system attachment requirements for wind load resistance. 5.7.1 “MDP” = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been applied). Refer to FBC 1609 for determination of design wind loads. NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION FL1654-R28 Polyglass Modified Bitumen Roof Systems Revision 26: 06/09/2021 Page 5 of 5 5.7.2 For mechanically attached components or partially-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed at least the Zone 1 PRIME design pressure determined in accordance with FBC Chapter 16. Elevated pressure zones shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29, Roofing Application Standard RAS 117 and Roofing Application Standard RAS 137. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (February 2020) for Zone 2/3 enhancements. 5.7.3 For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems. 5.8 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3. Refer to the Product Approval of the component manufacturer for components listed in Appendix 1 that are produced by a Product Manufacturer other than the report holder on Page 1 of this Evaluation Report. 6. INSTALLATION: Polyglass Modified Bitumen Roof Systems shall be installed in accordance with Polyglass USA, Inc. published installation instructions, subject to the Limitations / Conditions of Use noted herein. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements. Refer to Section 4 herein for products and production locations having met codified material standards. 9. QUALITY ASSURANCE ENTITY: UL, LLC – QUA9625: (414) 248-6409, karen.buchmann@ul.com - THE 98-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT - NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 1 of 98 APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE TABLE DECK APPLICATION TYPE DESCRIPTION PAGE 1A Wood New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 6 1B Wood New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 6-12 1C Wood New, Reroof (Tear-Off) or Recover A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 13-14 1D Wood New, Reroof (Tear-Off) or Recover B-1 Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 15 1E Wood New, Reroof (Tear-Off) or Recover C-1 Mech. Attached Insulation, Bonded Roof Cover 16-19 1F Wood New, Reroof (Tear-Off) or Recover D-2 Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 19-23 1G Wood New or Reroof (Tear-Off) E-2 Non-Insulated, Mech. Attached Base Sheet (nails), Bonded Roof Cover 23-28 1H Wood New, Reroof (Tear-Off) or Recover E-2 Non-Insulated, Mech. Attached Base Sheet (screws & plates), Bonded Roof Cover 29-36 1I Wood New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 36-37 2A Steel or Structural concrete New, Reroof (Tear-Off) or Recover B-1 Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 38-43 2B Steel or Structural concrete New, Reroof (Tear-Off) or Recover C-1 Mech. Attached Insulation, Bonded Roof Cover 44-50 2C Steel or Structural concrete New, Reroof (Tear-Off) or Recover D-2 Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 50-52 2D Steel or Structural concrete New, Reroof (Tear-Off) or Recover D-2 Insulated, Mech. Attached Velociflex, Bonded Roof Cover 53-54 3A Structural concrete New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 55-69 3B Structural concrete New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 69 4A Lightweight concrete New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 70-74 4B Lightweight concrete New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 74-76 4C Lightweight concrete New or Reroof (Tear-Off) E-2 Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 77-81 5A Cementitious wood fiber New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 82-83 5B Cementitious wood fiber Reroof (Tear-Off) or Recover A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 83-84 5C Cementitious wood fiber Reroof (Tear-Off) or Recover B-1 Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 85 5D Cementitious wood fiber Reroof (Tear-Off) or Recover C-1 Mech. Attached Insulation, Bonded Roof Cover 85 5E Cementitious wood fiber Reroof (Tear-Off) or Recover E-2 Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 85 6A Existing gypsum Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 86-90 6B Existing gypsum Reroof (Tear-Off) or Recover A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 91 6C Existing gypsum Reroof (Tear-Off) or Recover C-1 Mech. Attached Insulation, Bonded Roof Cover 91 6D Existing gypsum Reroof (Tear-Off) or Recover E-2 Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 91 7A Various Recover A-1 Bonded Insulation, Bonded Roof Cover 92-98 7B Various Recover F Non-Insulated, Bonded Roof Cover 98 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 2 of 98 The following notes apply to the systems outlined herein: 1 The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. 2 Fasteners shall be of sufficient length for the following engagements: ➢ Wood Deck: Minimum 1-inch plywood penetration or wood plank embedment. ➢ Steel Deck: Minimum 0.75-inch steel penetration and engage the top flute of the steel deck. ➢ Structural Concrete: Minimum 1-inch embedment into pilot hole in accordance with published installation instructions. 3 Unless otherwise noted, insulation may be any one layer or combination of FBC Approved (Local or Statewide) board(s) that meet FBC 1505 and, for foam plastic, FBC Chapter 26, when installed with the roof cover. 4 Minimum 200 psi, minimum 2-inch thick FBC Approved lightweight insulating concrete may be substituted for rigid insulation board for System Types B-1, C-1, C-2, D-1 or D-2, whereby fasteners are installed through the lightweight insulating concrete to engage the structural deck. The structural deck shall be of equal or greater type, thickness and strength to the steel and structural concrete deck listings. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. This is a wind uplift resistance allowance and does not purport to address non-wind-uplift-related issues, such as deck venting or moisture levels within the LWIC and the potential effect on overlying components. 5 Preliminary insulation attachment for System Type D: Unless otherwise noted, refer to Section 2.2.10.1.3 of FM Loss Prevention Data Sheet 1-29 (February 2020). 6 Unless otherwise noted, insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application; the ribbons/beads shall expand as noted in the manufacturer’s published instructions. ➢ Hot asphalt (HA): Full coverage at 25-30 lbs/square. ➢ DuPont INSTA STIK Quik Set Insulation Adhesive (D-IS): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. ➢ H.B. Fuller Millennium One Step Foamable Adhesive (M-OSFA): Continuous 0.25 to 0.5-inch wide ribbons, 12-inch o.c. ➢ H.B. Fuller Millennium PG-1 Pump Grade Adhesive (M-PG1): Continuous 0.25 to 0.5-inch wide ribbons, 12-inch o.c. ➢ OMG OlyBond 500 (OB500): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. Note: OlyBond Classic may be used where OlyBond 500 is referenced. ➢ OlyBond Classic (OB Classic): Full coverage at 1 gal/square. ➢ ICP Adhesive & Sealants Polyset CR-20: Continuous 2.5-3.5-inch wide ribbons, 12-inch o.c. ➢ Note: When multiple layers(s) of insulation and/or coverboard are installed in ribbon-applied adhesive, board joints shall be staggered. ➢ Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing. 7 Unless otherwise noted, all insulations are flat-stock or taper board of the minimum thickness noted. Tapered polyisocyanurate at the following thickness limitations may be substituted with the following Maximum Design Pressure (MDP) limitations. In no case shall these values be used to ‘increase’ the MDP listings in the tables; rather if MDP listing below meets or exceeds that listed for a particular system in the tables, then the thinner board listed below may be used as a drop-in for the equivalent thicker material listed in the table. ➢ M-OSFA: MDP = -157.5 psf (Min. 0.5-inch thick) ➢ M-PG1: MDP = -157.5 psf (Min. 0.5-inch thick) ➢ OB500: MDP = -45.0 psf (Min. 0.5-inch thick Multi-Max FA-3) ➢ OB500: MDP = -187.5 psf (Min. 0.5-inch thick ISO 95+ GL) ➢ OB500: MDP = -315.0 psf (Min. 0.5-inch thick ENRGY 3) ➢ OB500: MDP = -487.5 psf (Min. 0.5-inch thick ACFoam II) ➢ Polyset CR-20: MDP = -117.5 psf (Min. 1.0-inch thick) 8 For adhered roof insulation and board-size: Unless otherwise noted, refer to Section 2.2.10.6.2 of FM Loss Prevention Data Sheet 1-29 (February 2020). 9 For mechanically attached components or partially-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed at least the Zone 1 PRIME design pressure determined in accordance with FBC Chapter 16. Elevated pressure zones shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 3 of 98 ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29, Roofing Application Standard RAS 117 and Roofing Application Standard RAS 137. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (February 2020) for Zone 2/3 enhancements. 10 For assemblies with all components fully bonded, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems. 11 For mechanically attached components over existing decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard TAS 105. 12 For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question, field uplift testing in accordance shall be conducted on mock-ups of the proposed new roof assembly. For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction, as documented through field uplift testing. Field uplift testing shall be in accordance with ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124. 13 Refer to FBC 1511 for requirements and limitations regarding recover installations. For Structural Concrete Deck or Recover Applications using System Type C-1, C-2, D-1 or D-2, the insulation is optional. Alternatively, an FBC Approved insulation board or coverboard may be used as a separation layer. Board products shall be preliminarily attached prior to roof cover installation (Note 5 herein). The separator component shall be documented as meeting FBC 1505 and, for foam plastic, FBC Chapter 26, when installed with the roof cover in Recover applications. 14 Lightweight insulating concrete (LWIC) shall be cast in accordance with FBC Section 1917 to the satisfaction of the Authority Having Jurisdiction. For systems where specific LWIC is referenced, refer to current LWIC Product Approval for specific deck construction and limitations. Unless otherwise noted, for systems where specific LWIC is not referenced, the minimum design mix shall be 300 psi. In all cases, the minimum top-coat thickness is 2-inches. For LWIC over structural concrete, reference is made to FBC Section 1917.4.1, Point 1. For “pre-existent” LWIC references, listings were established through testing over lightweight concrete cast using only foaming agent (ASTM C896), water and Portland cement (ASTM C150), with no proprietary additives, in accordance with procedures adopted by Miami-Dade BCCO (FBC CER1592). Use of these listings in new construction or re-roof (tear-off) applications is at the discretion of the Designer or Record and Authority Having Jurisdiction. 15 For bonded membrane applications, unless otherwise noted, refer to the following. MEMBRANE / ADHESIVE COMBINATIONS REFERENCE LAYER MATERIAL APPLICATION BP-AA (Base and Ply sheets, Asphalt-Applied) Base Ply One or more plies Polyglass G2 Base, FBC Approved ASTM D4601, Type II Hot Asphalt at 20-40 lbs/square Ply One or more plies Polyglass Ply IV, Polyglass Ply VI, FBC Approved ASTM D2178, Type IV or VI Note: Asphalt-applied sheets or insulation shall not be applied to poly-film surfaced membranes. SBS-CA1 Base Ply One ply Elastobase V (sand/sand), Elastoflex V, Elastoflex S6, Elastoflex S6 HP, Elastoshield VP HT PG350 at 1.5-2.0 gal/square Cap Ply Elastoshield HT G, Elastoshield HT G FR, Elastoflex V G, Elastoflex V G FR, Elastoflex S6, Elastoflex S6 HP, Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS (sand-backed), Polyfresko G SBS FR (sand-backed) SBS-CA2 Base Ply One ply Elastobase V (sand/sand), Elastoflex V, Elastoflex S6, Elastoflex S6 HP Polyplus 35 at 1.5-2.0 gal/square Cap Ply Elastoshield HT G, Elastoshield HT G FR, Elastoflex V G, Elastoflex V G FR, Elastoflex S6, Elastoflex S6 HP, Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS (sand-backed), Polyfresko G SBS FR (sand-backed) SBS-AA (SBS, Asphalt-Applied) Base Ply or Ply One or more plies Elastobase V (sand/sand or poly/sand), Elastobase P (sand/sand or poly/sand), Elastoflex V, Elastoflex S6, Elastoflex S6 HP, Elastoshield VP HT Hot Asphalt at 20-40 lbs/square Cap Ply Elastoshield HT G, Elastoshield HT G FR, Elastoflex V, Elastoflex V G, Elastoflex V G FR, Elastoflex S6, Elastoflex S6 HP, Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS (sand-backed), Polyfresko G SBS FR (sand-backed) Note: Asphalt-applied sheets or insulation shall not be applied to poly-film surfaced membranes. SBS-TA (SBS, Torch-Applied) Base Ply or Ply One or more plies Elastobase V (sand/poly), Elastobase V (poly/poly), Elastoflex V, Elastoflex S6, Elastoflex S6 HP, Elastoshield VP HT, Elastoshield TS Torch-Applied Cap Ply Elastoshield HT G, Elastoshield HT G FR, Elastoflex V, Elastoflex V G, Elastoflex V G FR, Elastoflex S6, Elastoflex S6 HP, Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS (poly-film backed), Polyfresko G SBS FR (poly-film backed) NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 4 of 98 MEMBRANE / ADHESIVE COMBINATIONS REFERENCE LAYER MATERIAL APPLICATION SBS-SA-H (SBS, Self-Adhering, Hybrid Systems) Base Ply Elastobase SA Self-adhering (followed by torch-applied sheet) SBS-SA (SBS, Self-Adhering) Base Ply One or more plies Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V Plus, Elastoflex SA V Plus FR, Elastoflex SA Base HD Self-Adhering Cap Ply Elastoflex SA P, Elastoflex SA P FR, Polyreflect Note: Unless otherwise noted, permissible membrane substrates for SBS-SA are limited to the SBS-SA Base Ply options herein, Elastobase V or Elastobase P with a poly-film top surface. APP-CA1 Cap Ply Polyflex G FR PG350 at 1.5-2.0 gal/square APP-TA (APP, Torch-Applied) Base Ply or Ply One or more plies Polybase V, Polyflex, Polybond Torch-Applied Cap Ply Polyflex, Polyflex G, Polyflex G FR, Polybond, Polybond G, Polyfresko G, Polyfresko G FR APP-SA-H (APP, Self-Adhering, Hybrid Systems) Base Ply Polyflex SA Base Self-adhering (followed by torch-applied sheet) APP-SA (APP, Self-Adhering) Cap Ply Polyflex SA P, Polyflex SA P FR, Polyfresko G SA, Polyfresko G SA FR Self-Adhering Note: Unless otherwise noted, permissible membrane substrates for APP-SA are limited to the SBS-SA Base Ply options herein, Elastobase V or Elastobase P with a poly-film top surface. 16 Vapor barrier options for use over structural concrete deck followed by bonded insulation carry the following MDP limitations. The lesser of the MDP listings below vs. those in Table 3A applies. VAPOR BARRIER OPTIONS; STRUCTURAL CONCRETE DECK; FOLLOWED BY ADHESIVE-APPLIED INSULATION PER TABLE 3A: OPTION # PRIMER VAPOR BARRIER INSULATION ADHESIVE MDP (PSF) TYPE (NOTE 15) APPLICATION C-VB-1. PG100 Elastoflex SA V Plus Self-Adhering D-IS or CR-20, 12-inch o.c. -60.0 C-VB-2. PG100 Polybase V Torch-applied D-IS or CR-20, 12-inch o.c. -75.0 C-VB-3. PG100 Elastoflex SA P Self-Adhering D-IS, 12-inch o.c. -75.0 C-VB-4. PG100 Polyflex or Polybond Torch-applied M-OSFA, M-PG-1, OB500 or CR-20, 12-inch o.c. -121.7 C-VB-5. PG100 Elastoflex SA P Self-Adhering M-OSFA, 12-inch o.c. -157.5 C-VB-6. PG100 Polyflex or Polybond Torch-applied M-OSFA, M-PG-1, OB500 or CR-20, 6-inch o.c. -185.0 C-VB-7. PG100 Elastoflex SA P Self-Adhering CR-20, 12-inch o.c. -270.0 C-VB-8. PG100 Elastoflex SA V, Elastoflex SA V FR, Elastoflex SA V Plus, Elastoflex SA V Plus FR Self-Adhering M-OSFA, M-PG-1, OB500 or CR-20, 12-inch o.c. -240.0 C-VB-9. PG100 SBS-TA (with sanded-top-surface) Torch-applied M-OSFA, M-PG-1, OB500 or CR-20, 12-inch o.c. -240.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 5 of 98 17 The following surfacing may be applied to the Cap Ply without adverse effect on the system wind load performance. Refer to current Florida Product Approval for approved Polyglass and KM Coatings roof coatings for application limitations and a Roofing Materials Directory for fire ratings associated with coating usage. SURFACING OPTIONS FOR POLYGLASS MODIFIED BITUMEN ROOF SYSTEMS OPTION # SURFACING FLORIDA PRODUCT APPROVAL SURF-1. PG 300 FL10291 SURF-2. PG 600 FL10291 SURF-3. PG 650 FL10291 SURF-4. PG 700 FL10291 SURF-5. PG 700 QS FL10291 SURF-6. PG 800 FL10291 SURF-7. Polyplus 60 FL10291 SURF-8. Polyplus 65 FL10291 SURF-9. PolyBrite 60-FC NOA 20-0611.01 SURF-10. PolyBrite 70 FL10291 SURF-11. PolyBrite 70 QS FL10291 SURF-12. PolyBrite 75 FL10291 SURF-13. PolyBrite 71 HS FL10291 SURF-14. PolyBrite 90 FL10291 SURF-15. PolyBrite 90.1 NOA 19-0610.02 SURF-16. PolyBrite 95 FL10291 SURF-17. PolyBrite 95.1 NOA 19-0610.02 SURF-18. KM Acryl 15 FL27409 SURF-19. KM Acryl 15 QS FL27409 SURF-20. KM Acryl 25 FL27409 SURF-21. KM Acryl 25 QS FL27409 SURF-22. KM Acryl 40 HS FL27409 SURF-23. KM Acryl 85 FL27409 SURF-24. KM PS#250 FL27409 SURF-25. KM PS#220 FL27409 SURF-26. Turbo-Set FL10291 18 “MDP” = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609 for determination of design wind loads NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 6 of 98 TABLE 1A: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply SELF-ADHERING BASE PLY: W-1 Min. 15/32- inch plywood Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi-Max FA3 D-IS, M-OSFA, OB500 or CR-20 (Optional) additional layers(s) of base insulation D-IS, M-OSFA, OB500 or CR-20 SBS-SA (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -52.5 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: W-2 Min. 15/32- inch plywood Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi-Max FA3 D-IS, M-OSFA, OB500 or CR-20 (Optional) additional layers(s) of base insulation D-IS, M-OSFA, OB500 or CR-20 APP-SA-H (Optional) APP-TA APP-TA -52.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: W-3 Min. 15/32- inch plywood Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi-Max FA3 D-IS, M-OSFA, OB500 or CR-20 (Optional) additional layers(s) of base insulation D-IS, M-OSFA, OB500 or CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -52.5 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-4 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA or SBS- AA (Optional) BP-AA or SBS-AA SBS-AA, SBS-TA, APP-TA -45.0* W-5 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -45.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 7 of 98 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-6 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA or SBS- AA (Optional) BP-AA or SBS-AA SBS-AA, SBS-TA, APP-TA -52.5 W-7 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -52.5 W-8 Min. 19/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top), Elastovent, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA or SBS- AA (Optional) BP-AA or SBS-AA SBS-AA, SBS-TA, APP-TA -60.0 W-9 Min. 19/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top), Elastovent, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -60.0 W-10 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap Fasteners 12-inch o.c. at min. 4-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA or SBS- AA (Optional) BP-AA or SBS-AA SBS-AA, SBS-TA, APP-TA -60.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 8 of 98 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-11 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap Fasteners 12-inch o.c. at min. 4-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -60.0 W-12 Min. 15/32- inch plywood Elastobase V, Elastobase P(sanded-top) or Elastovent 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at four (4), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -67.5 W-13 Min. 15/32- inch plywood Polyglass G2 Base Simplex MAXX Cap 9-inch o.c. at min. 4-inch lap and 9- inch o.c. at four (4), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -82.5 W-14 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6- inch o.c. at five (5) equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -90.0 W-15 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 6-inch o.c. at min. 2-inch lap and 6- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -90.0 W-16 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) or Elastovent 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6- inch o.c. at four (4), equally spaced, staggered center rows Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or ENRGY-3 D-IS, OB500, CR-20 or M- OSFA, atop fastener rows, 7-inch o.c. Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board D-IS, OB500, CR- 20 or M- OSFA BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -60.0* SELF-ADHERING BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 9 of 98 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-17 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -45.0* W-18 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12- inch o.c. at two, equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -52.5 W-19 Min. 19/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top), Elastovent, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0 W-20 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap Fasteners 12-inch o.c. at min. 4-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0 W-21 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6- inch o.c. at four (4), equally spaced, staggered center rows Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or ENRGY-3 D-IS, OB500, CR-20 or M- OSFA, atop fastener rows, 7-inch o.c. (Optional) Additional layers of base insulation D-IS, OB500, CR- 20 or M- OSFA SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0* HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 10 of 98 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-22 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -45.0* W-23 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12- inch o.c. at two, equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -52.5 W-24 Min. 19/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top), Elastovent, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -60.0 W-25 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap Fasteners 12-inch o.c. at min. 4-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -60.0 W-26 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at four (4), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -67.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 11 of 98 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-27 Min. 15/32- inch plywood Polyglass G2 Base Simplex MAXX Cap 9-inch o.c. at min. 4-inch lap and 9- inch o.c. at four (4), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -82.5 W-28 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6- inch o.c. at five (5) equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -90.0 W-29 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 6-inch o.c. at min. 2-inch lap and 6- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime, SECUROCK Gypsum- Fiber Roof Board Hot asphalt APP- SA-H (Optional) APP-TA APP-TA -90.0 W-30 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6- inch o.c. at four (4), equally spaced, staggered center rows Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or ENRGY-3 D-IS, OB500, CR-20 or M- OSFA, atop fastener rows, 7-inch o.c. (Optional) Additional layers of base insulation D-IS, OB500, CR- 20 or M- OSFA APP- SA-H (Optional) APP-TA APP-TA -60.0* HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: W-31 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA- H (Optional) SBS-TA SBS-TA -45.0* W-32 Min. 15/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12- inch o.c. at two, equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA- H (Optional) SBS-TA SBS-TA -52.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 12 of 98 TABLE 1B: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-33 Min. 19/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top), Elastovent, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8- inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA- H (Optional) SBS-TA SBS-TA -60.0 W-34 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) Simplex MAXX Cap Fasteners 12-inch o.c. at min. 4-inch lap and 12- inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY-3, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA- H (Optional) SBS-TA SBS-TA -60.0 W-35 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) 32 ga., 1-5/8- inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6- inch o.c. at four (4), equally spaced, staggered center rows Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or ENRGY-3 D-IS, OB500, CR-20 or M- OSFA, atop fastener rows, 7-inch o.c. (Optional) Additional layers of base insulation D-IS, OB500, CR- 20 or M- OSFA SBS-SA- H (Optional) SBS-TA SBS-TA -60.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 13 of 98 TABLE 1C: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-36 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS-AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -52.5 W-37 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA or SBS-AA (Optional) BP-AA or SBS-AA SBS-AA, SBS-TA, APP-TA -60.0 W-38 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS-AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -60.0 W-39 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9- inch o.c. at four (4), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS-AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -82.5 SELF-ADHERING BASE PLY: W-40 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 14 of 98 TABLE 1C: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply W-41 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP-SA-H (Optional) APP-TA APP-TA -52.5 W-42 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP-SA-H (Optional) APP-TA APP-TA -60.0 W-43 Min. 15/32- inch plywood Polyglass G2 Base, Elastobase V, Elastobase P (sanded-top) or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9- inch o.c. at four (4), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP-SA-H (Optional) APP-TA APP-TA -82.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: W-44 Min. 19/32- inch plywood Elastobase V, Elastobase P (sanded-top) or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) Min. 1.5- inch Polytherm, ACFoam II, ENRGY- 3, Polytherm H, H- Shield, H-Shield CG, Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA-H (Optional) SBS-TA SBS-TA -60.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 15 of 98 TABLE 1D: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-45 Min. 19/32- inch plywood Min. 1.5-inch ENRGY 3, H-Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #12 or Trufast 3” Metal Insulation Plate with Trufast DP 1 per 1.3 ft2 Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -60.0 W-46 Min. 15/32- inch plywood Min. 2-inch Polytherm, ACFoam II, ENRGY-3, EnergyGuard Polyiso Insulation, H-Shield or Multi-Max FA3 Dekfast #14 with Dekfast PLT-H- 2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum Fiber Roof Board Hot asphalt SBS-AA, SBS- TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -75.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: W-47 Min. 15/32- inch plywood Min. 2-inch Polytherm, ACFoam II, ENRGY-3, EnergyGuard Polyiso Insulation, H-Shield or Multi-Max FA3 Dekfast #14 with Dekfast PLT-H- 2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum Fiber Roof Board Hot asphalt APP-SA-H (Optional) APP-TA APP-TA -75.0 TABLE 1E: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-48 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 1 per 2.0 ft2 BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP- AA, SBS-AA, SBS-TA, APP-TA SBS-AA, SBS- TA, APP-TA -30.0 W-49 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.8 ft2 SBS-AA, SBS- TA, APP-TA (Optional) SBS- AA, SBS-TA, APP-TA SBS-AA, SBS- TA, APP-TA -45.0 W-50 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.0 ft2 SBS-AA, SBS- TA, APP-TA (Optional) SBS- AA, SBS-TA, APP-TA SBS-AA, SBS- TA, APP-TA -75.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 16 of 98 TABLE 1E: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply W-51 Min. 19/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.5-inch Structodek High Density Fiberboard Roof Insulation or min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 with Dekfast #12 DP 1 per 1.3 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP- TA SBS-AA, SBS- TA, APP-TA -82.5 SELF-ADHERING BASE PLY: W-52 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch Polytherm, ACFoam II, H-Shield or Polytherm Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 2.7 ft2 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -30.0 W-53 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 1 per 2.0 ft2 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -30.0 W-54 Min. 15/32- inch plywood One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate, OMG 3 in. Ribbed Galvalume Plate (Flat) or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA None SBS-SA -45.0 W-55 Min. 15/32- inch plywood One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA None SBS-SA -45.0 W-56 Min. 15/32- inch plywood One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast DF-#14 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.8 ft2 SBS-SA (Optional when using torch- applied Cap Ply) SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA or APP-TA -45.0 W-57 Min. 15/32- inch plywood One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 OMG #14 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.8 ft2 SBS-SA (Optional when using torch- applied Cap Ply) SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA or APP-TA -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 17 of 98 TABLE 1E: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply W-58 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.0 ft2 SBS-SA (Optional) SBS- TA, APP-TA SBS-TA, APP- TA -60.0 W-59 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch ACFoam II, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, ENRGY 3 CGF, H-Shield, H- Shield CG, ISO 95+ GL, Multi-Max FA3, Polytherm or Ultra-Max optionally primed with POLYBRITE 745 or WB3000 Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate* 1 per 1.3 ft2 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -67.5* Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 180 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-60 Min. 19/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch ACFoam II, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, ENRGY 3 CGF, H-Shield, H- Shield CG, ISO 95+ GL, Multi-Max FA3, Polytherm or Ultra-Max optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 with Dekfast #12, OMG 3 in. Galvalume Plate (non- ribbed) or OMG AccuTrac Plate with #12 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast DP 1 per 1.3 ft2 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -67.5* HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: W-61 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch Polytherm, ACFoam II, H-Shield or Polytherm Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 2.7 ft2 APP-SA-H (Optional) APP- TA APP-TA -30.0 W-62 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 1 per 2.0 ft2 APP-SA-H (Optional) APP- TA APP-TA -30.0 W-63 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.8 ft2 APP-SA-H (Optional) APP- TA APP-TA -45.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 18 of 98 TABLE 1E: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply W-64 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch Polytherm, ACFoam II, H-Shield or Polytherm H Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 2.7 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -30.0 W-65 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 1 per 2.0 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -30.0 W-66 Min. 15/32- inch plywood One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate, OMG 3 in. Ribbed Galvalume Plate (Flat) or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -45.0 W-67 Min. 15/32- inch plywood One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -45.0 W-68 Min. 15/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board Dekfast #14 with Dekfast PLT-H-2-7/8, OMG #14 HD with OMG 3” Galvalume Steel Plates or Trufast #14 HD with Trufast 3-inch Insulation Plates 1 per 1.0 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -60.0 W-69 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch ACFoam II, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, ENRGY 3 CGF, H-Shield, H- Shield CG, ISO 95+ GL, Multi-Max FA3, Polytherm or Ultra-Max optionally primed with POLYBRITE 745 or WB3000 Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate* 1 per 1.3 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -67.5* Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 180 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 19 of 98 TABLE 1E: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply W-70 Min. 19/32- inch plywood (Optional) One or more layers, any combination, loose laid Min. 1.5-inch ACFoam II, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, ENRGY 3 CGF, H-Shield, H- Shield CG, ISO 95+ GL, Multi-Max FA3, Polytherm or Ultra-Max optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 with Dekfast #12, OMG 3 in. Galvalume Plate (non- ribbed) or OMG AccuTrac Plate with #12 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast DP 1 per 1.3 ft2 SBS-SA-H (Optional) SBS- TA SBS-TA -67.5* TABLE 1F: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-71 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P, Elastovent, Polyglass G2 Base, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 OMG Flat Bottom Plates (square) with Roofgrip #14, Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS- TA or APP-TA SBS-AA, SBS- TA, APP-TA -52.5 W-72 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS- TA or APP-TA SBS-AA, SBS- TA, APP-TA -60.0 W-73 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood One or more layers, any combination Loose-laid Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-AA, SBS-TA, APP- TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 20 of 98 TABLE 1F: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply W-74 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood One or more layers, any combination Loose-laid Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-TA APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-75 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS- TA or APP-TA SBS-AA, SBS- TA, APP-TA -75.0 W-76 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Polybase V Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows (Optional) APP- TA APP-TA -75.0 W-77 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood One or more layers, any combination Loose-laid Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-AA, SBS-TA, APP- TA -90.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 159 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-78 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood One or more layers, any combination Loose-laid Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-TA APP-TA -90.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 159 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-79 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS- TA or APP-TA SBS-AA, SBS- TA, APP-TA -90.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 21 of 98 TABLE 1F: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply W-80 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Polybase V Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows (Optional) APP- TA APP-TA -90.0 W-81 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P or Elastovent Trufast #12 DP or Trufast #14 HD with Trufast 3” Metal Insulation Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows (Optional) BP-AA or SBS-AA SBS-AA -90.0 W-82 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P or Elastovent OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS- TA, APP-TA SBS-AA, SBS- TA or APP-TA -90.0 W-83 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Polybase V OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows (Optional) APP- TA APP-TA -90.0 W-84 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood One or more layers, any combination Loose-laid Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-AA, SBS-TA, APP- TA -105.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 103 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-85 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood One or more layers, any combination Loose-laid Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows APP-TA APP-TA -105.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 103 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-86 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P or Elastovent Trufast #12 DP or Trufast #14 HD with Trufast 3” Metal Insulation Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows (Optional) BP-AA or SBS-AA SBS-AA -120.0 W-87 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P or Elastovent OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS- TA, APP-TA SBS-AA, SBS- TA or APP-TA -120.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 22 of 98 TABLE 1F: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply W-88 Min. 15/32-inch plywood One or more layers, any combination Prelim. Attached Polybase V OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows (Optional) APP- TA APP-TA -120.0 SELF-ADHERING BASE PLY: W-89 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P (poly- film top) Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -52.5* W-90 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P (poly- film top) OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -60.0* W-91 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood One or more layers, any combination Loose-laid Elastobase V, Elastobase P (poly- film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA SBS-SA, APP- SA, SBS-TA, APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: W-92 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P (poly- film top) Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows APP-SA-H APP-TA -52.5* W-93 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P (poly- film top) OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows APP-SA-H APP-TA -60.0* W-94 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood One or more layers, any combination Loose-laid Elastobase V, Elastobase P (poly- film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-SA-H APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: W-95 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P (poly- film top) Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA-H SBS-TA -52.5* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 23 of 98 TABLE 1F: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply W-96 Min. 19/32-inch plywood One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P (poly- film top) OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA-H SBS-TA -60.0* W-97 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood One or more layers, any combination Loose-laid Elastobase V, Elastobase P (poly- film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA-H SBS-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance TABLE 1G: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (NAILS), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply NO BASE PLY: W-98 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -45.0* W-99 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Elastobase V, Elastobase P or Elastovent 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -45.0 W-100 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None SBS-SA, APP-SA -45.0 W-101 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Polybase V 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None APP-TA -45.0 W-102 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -52.5 W-103 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -52.5 W-104 Min. 15/32-inch plywood Elastobase V, Elastobase P (poly-film top) Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None SBS-SA, APP-SA -52.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 24 of 98 TABLE 1G: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (NAILS), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply W-105 Min. 15/32-inch plywood Polybase V Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None APP-TA -52.5 W-106 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (sanded top) Simplex MAXX Cap 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -60.0 W-107 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (poly-film top) Simplex MAXX Cap 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows None SBS-TA, APP-TA -60.0 W-108 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Polybase V Simplex MAXX Cap 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows None APP-TA -60.0 W-109 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (poly-film top) Simplex MAXX Cap Note: MAXX Caps are to be primed with PG100 or ASTM D41 primer 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows None SBS-SA, APP-SA -60.0 W-110 Min. 19/32-inch plywood Elastobase V, Elastobase P, Elastovent, Polyglass G2 Base, CertainTeed Glasbase, Firestone MB Base, JM Perma-Ply 28 or GAFGLAS #75 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -60.0 W-111 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows None SBS-SA, APP-SA -60.0 W-112 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at four (4), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -67.5 W-113 Min. 15/32-inch plywood Polybase V 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at four (4), equally spaced, staggered center rows None APP-TA -67.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 25 of 98 TABLE 1G: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (NAILS), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply W-114 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P Simplex MAXX Cap 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -75.0 W-115 Min. 15/32-inch plywood Polybase V Simplex MAXX Cap 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows None APP-TA -75.0 W-116 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P Simplex MAXX Cap 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -90.0 W-117 Min. 15/32-inch plywood Polybase V Simplex MAXX Cap 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows None APP-TA -90.0 W-118 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 6-inch o.c. at min. 2-inch lap and 6-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -90.0 W-119 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. 4-inch o.c. at min. 4-inch lap and 4-inch o.c. at four (4), equally spaced, staggered center rows None SBS-SA, APP-SA -97.5 W-120 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 6-inch o.c. at min. 2-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -105.0 W-121 Min. 19/32-inch plywood Elastobase V, Elastobase P or Elastovent 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -112.5 W-122 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. Note: Tin caps are to be primed with PG100 or ASTM D41 primer. 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows None SBS-SA, APP-SA -112.5 ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-123 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 18-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -45.0* W-124 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Elastobase V, Elastobase P or Elastovent 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -45.0 W-125 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Polybase V 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows APP-TA APP-TA -45.0 W-126 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -52.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 26 of 98 TABLE 1G: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (NAILS), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply W-127 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -52.5 W-128 Min. 15/32-inch plywood Polybase V Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows APP-TA APP-TA -52.5 W-129 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (sanded top) Simplex MAXX Cap 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -60.0 W-130 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (poly-film top) Simplex MAXX Cap 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows SBS-TA SBS-TA, APP-TA -60.0 W-131 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Polybase V Simplex MAXX Cap 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows APP-TA APP-TA -60.0 W-132 Min. 19/32-inch plywood Elastobase V, Elastobase P, Elastovent, Polyglass G2 Base, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -60.0 W-133 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at four (4), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -67.5 W-134 Min. 15/32-inch plywood Polybase V 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at four (4), equally spaced, staggered center rows APP-TA APP-TA -67.5 W-135 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P Simplex MAXX Cap 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -75.0 W-136 Min. 15/32-inch plywood Polybase V Simplex MAXX Cap 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows APP-TA APP-TA -75.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 27 of 98 TABLE 1G: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (NAILS), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply W-137 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P Simplex MAXX Cap 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -90.0 W-138 Min. 15/32-inch plywood Polybase V Simplex MAXX Cap 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows APP-TA APP-TA -90.0 W-139 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 6-inch o.c. at min. 2-inch lap and 6-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -90.0 W-140 Min. 15/32-inch plywood Elastobase V, Elastobase P Simplex MAXX Cap 6-inch o.c. at min. 2-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -105.0 W-141 Min. 19/32-inch plywood Elastobase V, Elastobase P or Elastovent 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at four (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -112.5 SELF-ADHERING BASE PLY: W-142 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -45.0 W-143 Min. 15/32-inch plywood Elastobase V, Elastobase P (poly-film top) Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -52.5 W-144 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (poly-film top) Simplex MAXX Cap Note: MAXX Caps are to be primed with PG100 or ASTM D41 primer 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0 W-145 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0 W-146 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. 4-inch o.c. at min. 4-inch lap and 4-inch o.c. at four (4), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -97.5 W-147 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. Note: Tin caps are to be primed with PG100 or ASTM D41 primer. 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows Elastoflex SA V Plus, Elastoflex SA V Plus FR SBS-SA, APP-SA, SBS-TA, APP-TA -112.5 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 28 of 98 TABLE 1G: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (NAILS), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply W-148 Min. 15/32-inch plywood Polybase V, Elastobase V, Elastobase P (poly-film top) Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows APP-SA-H APP-TA -52.5 W-149 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows APP-SA-H APP-TA -60.0 W-150 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. 4-inch o.c. at min. 4-inch lap and 4-inch o.c. at four (4), equally spaced, staggered center rows APP-SA-H APP-TA -97.5 W-151 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. Note: Tin caps are to be primed with PG100 or ASTM D41 primer. 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows APP-SA-H APP-TA -112.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: W-152 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 12 ga. annular ring shank nails 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows SBS-SA-H SBS-TA -45.0 W-153 Min. 15/32-inch plywood Elastobase V, Elastobase P (poly-film top) Original Simplex Cap Nails (1-inch metal head diameter, 11 gauge x min. 1.25-inch long annular grooved shank) 6-inch o.c. at min. 3-inch lap and 6-inch o.c. at four (4), equally spaced, staggered center rows SBS-SA-H SBS-TA -52.5 W-154 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V (poly-film top) Simplex MAXX Cap Note: MAXX Caps are to be primed with PG100 or ASTM D41 primer 8-inch o.c. at min. 3-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows SBS-SA-H SBS-TA -60.0 W-155 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three (3), equally spaced, staggered center rows SBS-SA-H SBS-TA -60.0 W-156 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails. 4-inch o.c. at min. 4-inch lap and 4-inch o.c. at four (4), equally spaced, staggered center rows SBS-SA-H SBS-TA -97.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 29 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap NO BASE PLY: W-157 Min. 19/32-inch plywood Elastobase V, Elastobase P, Elastovent, Polyglass G2 Base, CertainTeed Glasbase, Firestone MB Base, JM Perma-Ply 28 or GAFGLAS #75 OMG Flat Bottom Plates (square) with Roofgrip #14, Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -52.5 W-158 Min. 19/32-inch plywood Elastobase V, Elastobase P or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -60.0 W-159 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-160 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V, Elastobase P (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None SBS-SA, APP-SA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-161 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-162 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -75.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 30 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap W-163 Min. 15/32-inch plywood Polybase V Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows None APP-TA -75.0 W-164 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -90.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 159 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-165 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows None APP-TA -90.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 159 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-166 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -90.0 W-167 Min. 15/32-inch plywood Polybase V Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows None APP-TA -90.0 W-168 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent Trufast #12 DP or Trufast #14 HD with Trufast 3” Metal Insulation Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA -90.0 W-169 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA or APP-TA -90.0 W-170 Min. 15/32-inch plywood Polybase V OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows None APP-TA -90.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 31 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap W-171 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows None SBS-AA, SBS-TA, APP-TA -105.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 103 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-172 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows None APP-TA -105.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 103 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-173 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent Trufast #12 DP or Trufast #14 HD with Trufast 3” Metal Insulation Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows None SBS-AA -120.0 W-174 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows None SBS-AA, SBS-TA or APP-TA -120.0 W-175 Min. 15/32-inch plywood Polybase V OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows None APP-TA -120.0 ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY: W-176 Min. 19/32-inch plywood Elastobase V, Elastobase P, Elastovent, Polyglass G2 Base, CertainTeed Glasbase, Firestone MB Base, JM Perma-Ply 28 or GAFGLAS #75 OMG Flat Bottom Plates (square) with Roofgrip #14, Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -52.5 W-177 Min. 19/32-inch plywood Elastobase V, Elastobase P or Elastovent OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -60.0 W-178 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -67.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 32 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-179 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-TA APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-180 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -75.0 W-181 Min. 15/32-inch plywood Polybase V Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 10-inch o.c. at min. 4-inch lap and 10-inch o.c. at three (3), equally spaced, staggered center rows APP-TA APP-TA -75.0 W-182 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -90.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 159 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-183 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 9-inch o.c. at min. 2-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-TA APP-TA -90.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 159 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-184 Min. 15/32-inch plywood Polyglass G2 Base, Elastobase V, Elastobase P or Elastovent Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -90.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 33 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap W-185 Min. 15/32-inch plywood Polybase V Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Round Metal Plate with OMG HD, OMG Flat Bottom Plate (Accutrac) with Roofgrip #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced, staggered center rows APP-TA APP-TA -90.0 W-186 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent Trufast #12 DP or Trufast #14 HD with Trufast 3” Metal Insulation Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows BP-AA or SBS-AA SBS-AA -90.0 W-187 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent OMG #12 Standard Roofgrip or OMG #14 Heavy Duty (min. 1-5/8-inch long) with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -90.0 W-188 Min. 15/32-inch plywood Polybase V OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows APP-TA APP-TA -90.0 W-189 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Elastobase V, Elastobase P or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -105.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 103 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-190 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB or min. 15/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at three (3), equally spaced, staggered center rows APP-TA APP-TA -105.0 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 103 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-191 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent Trufast #12 DP or Trufast #14 HD with Trufast 3” Metal Insulation Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows BP-AA or SBS-AA SBS-AA -120.0 W-192 Min. 15/32-inch plywood Elastobase V, Elastobase P or Elastovent OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-AA, SBS-TA, APP-TA -120.0 W-193 Min. 15/32-inch plywood Polybase V OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3” Round Metal Plates or OMG Flat Bottom Metal Plates 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at five (5), equally spaced, staggered center rows APP-TA APP-TA -120.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 34 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap W-194 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V (sanded top) or Elastovent Trufast Versa Fasteners (min. ¾” penetration) & Plates; 1 screws per plate in center hole* 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced center rows BP-AA, SBS-AA, SBS- TA, APP-TA SBS-AA, SBS-TA, APP-TA -127.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 141 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-195 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 1 screws per plate in center hole* 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced center rows SBS-TA SBS-TA, APP-TA -127.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 141 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance W-196 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Polybase V Trufast Versa Fasteners (min. ¾” penetration) & Plates; 1 screws per plate in center hole* 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced center rows APP-TA APP-TA -127.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 141 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance SELF-ADHERING BASE PLY: W-197 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -52.5* W-198 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0* W-199 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V, Elastobase P (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 35 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap W-200 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 1 screws per plate in center hole* Note: Versa-Fast Plates shall be primed with PG100 or ASTM D41 primer. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced center rows SBS-SA SBS-SA, APP-SA, SBS-TA, APP-TA -127.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 141 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: W-201 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-SA-H APP-TA -52.5* W-202 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-SA-H APP-TA -60.0* W-203 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V, Elastobase P (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows APP-SA-H APP-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: W-204 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA-H SBS-TA -52.5* W-205 Min. 19/32-inch plywood Elastobase V, Elastobase P (poly-film top) OMG Flat Bottom Plates (square) with Roofgrip #12 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA-H SBS-TA -60.0* W-206 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V, Elastobase P (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 2 screws per plate installed 180° into the holes of the plate, parallel to the width-direction of the sheet* 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two (2), equally spaced, staggered center rows SBS-SA-H SBS-TA -67.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 199 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 36 of 98 TABLE 1H: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET (SCREWS & PLATES), BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap W-207 APA rated, 19/32 CAT, 0.578 in., Exposure 1 OSB or min. 19/32” APA rated plywood Elastobase V (poly-film top) Trufast Versa Fasteners (min. ¾” penetration) & Plates; 1 screws per plate in center hole* Note: Versa-Fast Plates shall be primed with PG100 or ASTM D41 primer. 9-inch o.c. at min. 4-inch lap and 9-inch o.c. at four (4), equally spaced center rows SBS-SA-H SBS-TA -127.5 Note: *For re-roof or recover construction, field withdrawal resistance testing (Note 11) shall yield minimum 141 lbf. Additional Versa-Fast Fasteners within each Versa-Fast Plate may be utilized to produce minimum withdrawal resistance TABLE 1I: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER System No. Deck (Note 1) Primer Roof Cover (Note 15) MDP (psf) Joint Treatment Base Ply Ply Cap Ply SELF-ADHERING BASE PLY: W-208 APA rated, 7/16 CAT, 0.418 in., Exposure 1 OSB None OSB joints are covered with 4-inch wide strips of Elastoflex SA V, rolled into place to create continuous bond. Elastoflex SA V Plus or Elastoflex SA V Plus FR (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -52.5 W-209 Min. 15/32- inch plywood None None SBS-SA (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -90.0 W-210 Min. 15/32- inch plywood PG100 None SBS-SA (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -97.5 W-211 Min. 15/32- inch plywood (Optional) PG100 Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus, rolled into place to create continuous bond. Elastoflex SA V or Elastoflex SA V FR (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -97.5 W-212 Min. 15/32- inch plywood POLYBRITE 745 or WB3000 None SBS-SA (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -105.0 W-213 Min. 15/32- inch plywood (Optional) PG100 Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus, rolled into place to create continuous bond. Elastoflex SA V Plus or Elastoflex SA V Plus FR (Optional) SBS-SA, SBS- TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -135.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: W-214 Min. 15/32- inch plywood (Optional) PG100 None APP-SA-H (Optional) APP-TA APP-TA -90.0 W-215 Min. 15/32- inch plywood (Optional) PG100 Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus, rolled into place to create continuous bond. APP-SA-H (Optional) APP-TA APP-TA -135.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 37 of 98 TABLE 1I: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER System No. Deck (Note 1) Primer Roof Cover (Note 15) MDP (psf) Joint Treatment Base Ply Ply Cap Ply W-216 Min. 15/32- inch plywood None None SBS-SA-H (Optional) SBS-TA SBS-TA -90.0 W-217 Min. 15/32- inch plywood PG100 None SBS-SA-H (Optional) SBS-TA SBS-TA -97.5 W-218 Min. 15/32- inch plywood (Optional) PG100 Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus, rolled into place to create continuous bond. SBS-SA-H (Optional) SBS-TA SBS-TA -97.5 W-219 Min. 15/32- inch plywood POLYBRITE 745 or WB3000 None SBS-SA-H (Optional) SBS-TA SBS-TA -105.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 38 of 98 TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT- OR TORCH-APPLIED BASE PLY: S-1. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #14 HD or OMG 3-inch Galv Plate with OMD HD 1 per 2.0 ft2 Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* S-2. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #14 HD or OMG 3-inch Galv Plate with OMD HD 1 per 4.0 ft2 Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* S-3. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete Min. 1.5-inch ENRGY 3, H-Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.3 ft2 Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -90.0 S-4. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete Min. 1.5-inch ENRGY 3, H-Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #14 or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.3 ft2 Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA, SBS- AA (Top surface primed with PG100 primer) SBS-SA, SBS-TA or APP-TA SBS-SA, APP-SA, SBS-TA or APP-TA -90.0 S-5. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board D-IS SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -30.0* S-6. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board D-IS SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 39 of 98 TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply S-7. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum- Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -30.0* S-8. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum- Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -45.0 S-9. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board OB500 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -30.0* S-10. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board OB500 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -45.0 S-11. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -30.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 40 of 98 TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply S-12. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -45.0 S-13. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H or H-Shield Dekfast PLT-R-3 with Dekfast #14, OMG 3” Galvalume Steel Plates with OMG #14 Roofgrip 1 per 1.0 ft2 Additional optional layer(s) base insulation followed by min. 0.25-inch DensDeck Prime CR-20 SBS-AA, SBS-TA, APP-TA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -105.0 SELF-ADHERING BASE PLY: S-14. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board PRIMER: POLYBRITE 745 or WB3000 D-IS SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -30.0* S-15. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board PRIMER: POLYBRITE 745 or WB3000 D-IS SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -45.0 S-16. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5- inch SECUROCK Cement Roof Board PRIMER: POLYBRITE 745 or WB3000 M-OSFA or M-PG1 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -30.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 41 of 98 TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply S-17. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5- inch SECUROCK Cement Roof Board PRIMER: POLYBRITE 745 or WB3000 M-OSFA or M-PG1 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -45.0 S-18. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board PRIMER: POLYBRITE 745 or WB3000 OB500 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -30.0* S-19. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board PRIMER: POLYBRITE 745 or WB3000 OB500 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -45.0 S-20. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board PRIMER: POLYBRITE 745 or WB3000 CR-20 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -30.0* S-21. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board PRIMER: POLYBRITE 745 or WB3000 CR-20 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 42 of 98 TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply S-22. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H or H-Shield Dekfast PLT-R-3 with Dekfast #14, OMG 3” Galvalume Steel Plates with OMG #14 Roofgrip 1 per 1.0 ft2 Additional optional layer(s) base insulation followed by min. 0.25-inch DensDeck Prime CR-20 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -97.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: S-23. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H or H-Shield Dekfast PLT-R-3 with Dekfast #14, OMG 3” Galvalume Steel Plates with OMG #14 Roofgrip 1 per 1.0 ft2 Additional optional layer(s) base insulation followed by min. 0.25-inch DensDeck Prime CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -97.5 COLD-APPLIED BASE PLY: S-24. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board D-IS SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -30.0* S-25. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board D-IS SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -45.0 S-26. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -30.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 43 of 98 TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply S-27. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -45.0 S-28. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board OB500 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -30.0* S-29. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum- Fiber Roof Board OB500 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -45.0 S-30. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 4.0 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -30.0* S-31. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete Min. 2-inch Polytherm, ACFoam II, ENRGY 3, EnergyGuard Polyiso Insulation, Polytherm H, H-Shield or Multi-Max FA3 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plate with Trufast #14 HD 1 per 1.6 ft2 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 44 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply ASPHALT- OR TORCH-APPLIED BASE PLY: S-32. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.75-inch JM Fesco Board (homogeneous) or min. 1.5-inch JM Fesco Board (laminated) OMG AccuTrac Plate or OMG 3 in. Ribbed Galvalume Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.0 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* S-33. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.5-inch Structodek High Density Fiberboard Roof Insulation or G-P FiberBase HD or HD Excel OMG AccuTrac Plate or OMG 3 in. Ribbed Galvalume Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 4.0 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* S-34. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board OMG AccuTrac Plate or OMG 3 in. Ribbed Galvalume Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 4.0 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* S-35. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 2-inch H-Shield WF OMG AccuTrac Plate or OMG 3 in. Ribbed Galvalume Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 4.0 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* S-36. Min. 22 ga., type B, Grade 40 steel; 6 ft span; 5/8” puddle welds, 6” o.c. One or more layers, any combination, min. 1.5” thick, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 or PTL-R-3 plates with Dekfast DF- #12-PH3, DF-#14-PH3 or DF-#15-PH3 fasteners or OMG 3 in. Galvalume Steel Plate, 3 in. Ribbed Galvalume Plate (Flat) or AccuTrac Flat Bottom Plate with OMG #12 Roofgrip, #14 Roofgrip or OMG #15 Roofgrip fasteners or Trufast 3” Metal Insulation Plate with Trufast #12 DP, Trufast #14 HD or Trufast #15 EHD fasteners 1 per 2.0 ft2 SBS-TA or APP-TA (Optional) SBS-TA or APP-TA SBS-TA or APP-TA -52.5 S-37. Min. 22 ga., type B, Grade 40 steel; 6 ft span; 5/8” puddle welds, 6” o.c. One or more layers, any combination, min. 1.5” thick, loose laid Min. 0.25-inch DensDeck Prime Dekfast PLT-H-2-7/8 or PTL-R-3 plates with Dekfast DF- #12-PH3, DF-#14-PH3 or DF-#15-PH3 fasteners or OMG 3 in. Galvalume Steel Plate, 3 in. Ribbed Galvalume Plate (Flat) or AccuTrac Flat Bottom Plate with OMG #12 Roofgrip, #14 Roofgrip or OMG #15 Roofgrip fasteners or Trufast 3” Metal Insulation Plate with Trufast #12 DP, Trufast #14 HD or Trufast #15 EHD fasteners 1 per 2.0 ft2 SBS-TA or APP-TA (Optional) SBS-TA or APP-TA SBS-TA or APP-TA -60.0 S-38. Min. 22 ga., type B, Grade 40 steel; 6 ft span; 5/8” puddle welds, 6” o.c. One or more layers, any combination, min. 1.5” thick, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 or PTL-R-3 plates with Dekfast DF- #12-PH3, DF-#14-PH3 or DF-#15-PH3 fasteners or OMG 3 in. Galvalume Steel Plate, 3 in. Ribbed Galvalume Plate (Flat) or AccuTrac Flat Bottom Plate with OMG #12 Roofgrip, #14 Roofgrip or OMG #15 Roofgrip fasteners or Trufast 3” Metal Insulation Plate with Trufast #12 DP, Trufast #14 HD or Trufast #15 EHD fasteners 1 per 1.6 ft2 SBS-TA or APP-TA (Optional) SBS-TA or APP-TA SBS-TA or APP-TA -67.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 45 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply S-39. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board OMG 3-inch Galvalume Steel Plate with OMG #14 HD 1 per 1.8 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -75.0 S-40. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.5-inch Structodek High Density Fiberboard Roof Insulation or min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8 with Dekfast #12 (steel only) or #14 or Trufast 3” Metal Insulation Plate with Trufast DP (steel only) or HD 1 per 1.3 ft2 (Optional if using AA Ply) BP-AA, SBS- AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -82.5 SELF-ADHERING BASE PLY: S-41. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch Polytherm, ACFoam II, H-Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, OMG AccuTrac Flat Bottom Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.7 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -30.0 S-42. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -37.5* S-43. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -37.5* S-44. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DEXcell FA Glass Mat Roof Board Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8, isofast PLT-S-2-3/4X2-3/4 or Dekfast PLT-R-3 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -37.5* S-45. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch H-Shield or Polytherm OMG AccuTrac Flat Bottom Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.0 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -45.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 46 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply S-46. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plates with Trufast #14 HD Fasteners 1 per 2.0 ft2 SBS-SA None SBS-CA1, SBS-CA2, APP-CA1 -45.0* S-47. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 OMG 3 in. Galvalume Plate (non-ribbed) with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.0 ft2 SBS-SA (Optional) SBS-SA, SBS-TA or APP-TA SBS-SA, APP-SA, SBS-TA or APP-TA -45.0* S-48. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate, OMG 3 in. Ribbed Galvalume Plate (Flat) or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA None SBS-SA -45.0 S-49. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA None SBS-SA -45.0 S-50. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.8 ft2 SBS-SA (Optional when using torch- applied Cap Ply) SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA or APP-TA -45.0 S-51. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.8 ft2 SBS-SA (Optional when using torch- applied Cap Ply) SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA or APP-TA -45.0 S-52. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch H-Shield or Polytherm optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14 1 per 2.0 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -60.0 S-53. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 OMG 3 in. Galvalume Plate (non-ribbed) with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 1.6 ft2 SBS-SA (Optional) SBS-TA or APP-TA SBS-TA or APP-TA -60.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 47 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply S-54. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch ACFoam II, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, ENRGY 3 CGF, H-Shield, H-Shield CG, ISO 95+ GL, Multi-Max FA3, Polytherm or Ultra-Max optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 with Dekfast #12 (steel only) or Dekfast #14, OMG 3 in. Galvalume Plate (non-ribbed) or OMG AccuTrac Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty or Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 1.3 ft2 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -67.5* S-55. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 OMG 3 in. Galvalume Plate (non-ribbed) with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 1.3 ft2 SBS-SA (Optional) SBS-TA or APP-TA SBS-TA or APP-TA -72.5 S-56. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board OMG 3-inch Galvalume Steel Plate with OMG #14 HD 1 per 1.8 ft2 SBS-SA (Optional) SBS-TA SBS-TA -75.0 S-57. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.0 ft2 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -90.0 S-58. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.0 ft2 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -97.5 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: S-59. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch Polytherm, ACFoam II, H-Shield or Polytherm Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, OMG AccuTrac Flat Bottom Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.7 ft2 APP-SA-H (Optional) APP-TA APP-TA -30.0 S-60. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 APP-SA-H (Optional) APP-TA APP-TA -37.5* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 48 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply S-61. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 APP-SA-H (Optional) APP-TA APP-TA -37.5* S-62. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DEXcell FA Glass Mat Roof Board Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8, isofast PLT-S-2-3/4X2-3/4 or Dekfast PLT-R-3 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 APP-SA-H (Optional) APP-TA APP-TA -37.5* S-63. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch H-Shield or Polytherm OMG AccuTrac Flat Bottom Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.0 ft2 APP-SA-H (Optional) APP-TA APP-TA -45.0* HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: S-64. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch Polytherm, ACFoam II, H-Shield or Polytherm H Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, OMG AccuTrac Flat Bottom Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.7 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -30.0 S-65. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -37.5* S-66. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -37.5* S-67. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DEXcell FA Glass Mat Roof Board Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8, isofast PLT-S-2-3/4X2-3/4 or Dekfast PLT-R-3 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.7 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -37.5* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 49 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply S-68. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch H-Shield or Polytherm H OMG AccuTrac Flat Bottom Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 2.0 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -45.0* S-69. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate, OMG 3 in. Ribbed Galvalume Plate (Flat) or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -45.0 S-70. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 with Polygrip Hex Plate or Dekfast #14 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plate 1 per 2.0 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -45.0 S-71. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch H-Shield or Polytherm optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14 1 per 2.0 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -60.0 S-72. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 OMG 3 in. Galvalume Plate (non-ribbed) with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 1.6 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -60.0 S-73. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 1.5-inch ACFoam II, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, ENRGY 3 CGF, H-Shield, H-Shield CG, ISO 95+ GL, Multi-Max FA3, Polytherm or Ultra-Max optionally primed with POLYBRITE 745 or WB3000 Dekfast PLT-H-2-7/8 or Dekfast PLT-R-3 with Dekfast #12 (steel only) or Dekfast #14, OMG 3 in. Galvalume Plate (non-ribbed) or OMG AccuTrac Plate with #12 Roofgrip (steel only) or OMG #14 Heavy Duty or Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 1.3 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -67.5* S-74. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 OMG 3 in. Galvalume Plate (non-ribbed) with #12 Roofgrip (steel only) or OMG #14 Heavy Duty, Dekfast PLT-H-2-7/8 with Dekfast #12 DP (steel only) or Dekfast #14, Trufast 3” Metal Insulation Plate with Trufast #12 DP (steel only) or Trufast #14 HD 1 per 1.3 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 50 of 98 TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply S-75. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete (Optional) One or more layers, any combination, loose laid Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board OMG 3-inch Galvalume Steel Plate with OMG #14 HD 1 per 1.8 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -75.0 S-76. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Accutrac Flat Bottom Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.0 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -90.0 S-77. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination, min. 1-inch, loose laid Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 Polygrip #14 or Polygrip #15 with Polygrip Hex Plate or Dekfast DF-#14 or DF-#15 with Dekfast PLT-H-2-7/8 or OMG #14 Roofgrip or #15 Roofgrip with OMG 3 in. Round Metal Plate or Trufast #14 HD or Trufast #15 EHD Fasteners with Trufast 3” Metal Insulation Plate 1 per 1.0 ft2 SBS-SA-H (Optional) SBS-TA SBS-TA -97.5 COLD-APPLIED BASE PLY: S-78. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination, loose laid Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Dekfast Galvalume Steel Hex with Dekfast #14, OMG 3” Galvalume Ribbed Plates with OMG #14 Roofgrip or Trufast 3” Metal Insulation Plates with Trufast #14 HD Fasteners 1 per 2.0 ft2 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS-CA2, APP-CA1 -45.0* TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply ASPHALT- OR TORCH-APPLIED BASE PLY: S-79. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P, Elastovent or JM Perma-Ply 28 Roofgrip #14 with OMG Flat Bottom Plates (square), Dekfast #14 with Dekfast PLT-H-2-7/8 or Trufast #14 HD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -45.0* S-80. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P, Elastovent, Polyglass G2 Base, CertainTeed Glasbase, Firestone MB Base, JM Perma- Ply 28 or GAFGLAS #75 Roofgrip #14 with OMG Flat Bottom Plates (square), Dekfast #14 with Dekfast PLT-H-2-7/8 or Trufast #14 HD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -52.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 51 of 98 TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply S-81. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V, Elastobase P or Elastovent Roofgrip #12 (steel only) or #14 with OMG Flat Bottom Plates (square) 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -60.0 S-82. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Polybond, Polyflex Dekfast #14 with Dekfast PLT-H-2-7/8 or OMG Roofgrip #14 OMG Flat Bottom Plates 12-inch o.c. at the min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered center rows (Optional) BP- AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -112.5 SELF-ADHERING BASE PLY: S-83. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V or Elastobase P with poly top surface Roofgrip #14 with OMG Flat Bottom Plates (square), Dekfast #14 with Dekfast PLT-H-2-7/8 or Trufast #14 HD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -52.5* S-84. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V or Elastobase P with poly top surface Roofgrip #12 (steel only) or #14 with OMG Flat Bottom Plates (square) 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -60.0* HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: S-85. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V or Elastobase P with poly top surface Roofgrip #14 with OMG Flat Bottom Plates (square), Dekfast #14 with Dekfast PLT-H-2-7/8 or Trufast #14 HD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows APP-SA-H APP-TA -52.5* S-86. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V or Elastobase P with poly top surface Roofgrip #12 (steel only) or #14 with OMG Flat Bottom Plates (square) 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows APP-SA-H APP-TA -60.0* HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: S-87. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V or Elastobase P with poly top surface Roofgrip #14 with OMG Flat Bottom Plates (square), Dekfast #14 with Dekfast PLT-H-2-7/8 or Trufast #14 HD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA-H SBS-TA -52.5* S-88. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastobase V or Elastobase P with poly top surface Roofgrip #12 (steel only) or #14 with OMG Flat Bottom Plates (square) 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows SBS-SA-H SBS-TA -60.0* COLD-APPLIED BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 52 of 98 TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply S-89. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Loose laid Elastobase V Trufast #12 DP (steel only), #14 HD or #15 EHD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at one staggered center row (Optional) SBS-CA1, SBS- CA2 SBS-CA1, SBS-CA2, APP-CA1 -45.0* S-90. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Loose laid Elastovent Trufast #12 DP (steel only), #14 HD or #15 EHD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at one staggered center row (Optional) SBS-CA1 SBS-CA1, APP-CA1 -45.0* S-91. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Loose laid Elastobase V Trufast #12 DP (steel only), #14 HD or #15 EHD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows (Optional) SBS-CA1, SBS- CA2 SBS-CA1, SBS-CA2, APP-CA1 -67.5 S-92. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural concrete One or more layers, any combination Loose laid Elastovent Trufast #12 DP (steel only), #14 HD or #15 EHD with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows (Optional) SBS-CA1 SBS-CA1, APP-CA1 -67.5 S-93. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination Loose- laid Elastoflex S6 Trufast #12 DP (steel only) or Trufast #14 HD (steel or concrete) with Trufast 3” Metal Insulation Plate 6-inch o.c. at min. 4-inch lap and 6-inch o.c. at one staggered center row (Optional) Elastoflex S6 applied in PG350 at 1.5- 2.0 gal/square SBS-CA1 -75.0* S-94. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination Loose- laid Elastoflex S6 Trufast #12 DP (steel only) or Trufast #14 HD (steel or concrete) with Trufast 3” Metal Insulation Plate 12-inch o.c. at min. 4-inch lap and 12-inch o.c. at two, equally spaced, staggered center rows (Optional) Elastoflex S6 applied in PG350 at 1.5- 2.0 gal/square SBS-CA1 -90.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 53 of 98 TABLE 2D: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED VELOCIFLEX, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply ASPHALT- OR TORCH-APPLIED BASE PLY: S-95. Min. 22 ga., type B, 40 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 Trufast #14 HD with Trufast 2” Barbed Seam Plates 18-inch o.c. within the 4-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA -30.0 S-96. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoshield VP HT Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.4” Barbed Metal Seam Plates, Trufast 2.4” Scoop Seam Plates or Trufast 2.75” Barbed Metal Seam Plates or Dekfast #15 with Dekfast Galvalume Steel 1-1/2” x 2-3/4” Oval Barbed Plate (aka, Dekfast PLT-O2- 3/4-12B) or Dekfast Galvalume Steel 2-3/8” Round Barbed Plate (aka, Dekfast PLT-R-2-3/8-6B) 18-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA -37.5 S-97. Min. 22 ga., type B, 33 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.4” Scoop Seam Plates or Trufast 2.75” Barbed Metal Seam Plates 12-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA -45.0 S-98. Min. 22 ga., type B, 33 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.75” Barbed Metal Seam Plates 6-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA -60.0 S-99. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 HP Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.75” Barbed Metal Seam Plates or OMG Super XHD Fasteners (steel only) with OMG 2 3/4 Super XHD Barbed Stress Plates 18-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA (D6164 only) -60.0 S-100. Min. 22 ga., type B, 33 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 HP Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.75” Barbed Metal Seam Plates or OMG Super XHD Fasteners (steel only) with OMG 2 3/4 Super XHD Barbed Stress Plates 12-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA (D6164 only) -82.5 S-101. Min. 22 ga., type B, 33 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoshield VP HT Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.4” Barbed Metal Seam Plates, Trufast 2.4” Scoop Seam Plates or Trufast 2.75” Barbed Metal Seam Plates or Dekfast #15 with Dekfast Galvalume Steel 1-1/2” x 2-3/4” Oval Barbed Plate (aka, Dekfast PLT-O2- 3/4-12B) or Dekfast Galvalume Steel 2-3/8” Round Barbed Plate (aka, Dekfast PLT-R-2-3/8-6B) 12-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA (D6164 only) -82.5 S-102. Min. 22 ga., type B, Grade 80 steel One or more layers, any combination Prelim. Attached Polyflex Dekfast #15 HS with Dekfast Galvalume Steel 2- 3/8” Round Barbed Plate (aka, Dekfast PLT-R-2- 3/8-6B) 12-inch o.c. within the 5-inch wide, torch-sealed side lap (Optional) APP-TA SBS-TA, APP- TA -82.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 54 of 98 TABLE 2D: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED VELOCIFLEX, BONDED ROOF COVER System No. Deck (Note 1) Insulation Layer(s) (Note 13) Base Sheet Roof Cover (Note 15) MDP (psf) Type Attach Type Fasten (Note 11) Attach Base Ply Cap Ply S-103. Min. 22 ga., type B, Grade 80 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Polybond or Polyflex Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.4 in. Barbed Seam Plates 12-inch o.c. within the 6-inch wide, torch-sealed side lap (Optional) APP-TA SBS-TA, APP- TA -82.5 S-104. Min. 22 ga., type B, 40 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoshield VP HT Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.4” Barbed Metal Seam Plates, Trufast 2.4” Scoop Seam Plates or Trufast 2.75” Barbed Metal Seam Plates or Dekfast #15 with Dekfast Galvalume Steel 1-1/2” x 2-3/4” Oval Barbed Plate (aka, Dekfast PLT-O2- 3/4-12B) or Dekfast Galvalume Steel 2-3/8” Round Barbed Plate (aka, Dekfast PLT-R-2-3/8-6B) 6-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA (D6164 only) -97.5 S-105. Min. 22 ga., type B, Grade 40 steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 HP Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.75” Barbed Metal Seam Plates or OMG Super XHD Fasteners (steel only) with OMG 2 3/4 Super XHD Barbed Stress Plates 6-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) SBS-TA SBS-TA (D6164 only) -135.0 COLD-APPLIED BASE PLY: S-106. Min. 22 ga., type B, 40 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 HP Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.75” Barbed Metal Seam Plates or OMG Super XHD Fasteners (steel only) with OMG 2 3/4 Super XHD Barbed Stress Plates 18-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) Elastoflex S6 applied in PG350 at 1.5- 2.0 gal/square SBS-CA1 -60.0 Note: When extrapolating base sheet attachment for this system for elevated pressure zones, any additional fastener rows installed in the center of the sheet shall be stripped-in with minimum 6-inch wide strips of torch-applied, sand-top-surfaced, Polyglass SBS modified bitumen membrane prior to placement of subsequent Base Ply or Cap Ply membranes in PG350 adhesive. S-107. Min. 22 ga., type B, 40 ksi steel or min. 2,500 psi structural concrete One or more layers, any combination Prelim. Attached Elastoflex S6 HP Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only) with Trufast 2.75” Barbed Metal Seam Plates or OMG Super XHD Fasteners (steel only) with OMG 2 3/4 Super XHD Barbed Stress Plates 12-inch o.c. within the 5-inch wide, torch-sealed or heat- welded side laps (Optional) Elastoflex S6 applied in PG350 at 1.5- 2.0 gal/square SBS-CA1 -82.5 Note: When extrapolating base sheet attachment for this system for elevated pressure zones, any additional fastener rows installed in the center of the sheet shall be stripped-in with minimum 6-inch wide strips of torch-applied, sand-top-surfaced, Polyglass SBS modified bitumen membrane prior to placement of subsequent Base Ply or Cap Ply membranes in PG350 adhesive. NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 55 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT OR TORCH APPLIED BASE PLY: C-1 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 C-2 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch DensDeck Prime D-IS SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-3 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board D-IS SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-4 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 OB500 0.5-inch SECUROCK Cement Roof Board OB500 SBS-TA (Optional) SBS-TA SBS-TA -187.5 C-5 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 C-6 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 OB500, 6- inch o.c. 0.5-inch SECUROCK Cement Roof Board OB500, 6- inch o.c. SBS-TA (Optional) SBS-TA SBS-TA -232.5 C-7 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-8 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board OB500 SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-9 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 M-OSFA or M-PG1 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-TA (Optional) SBS-TA SBS-TA -187.5 C-10 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield M-OSFA or M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA or M-PG1 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 C-11 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 M-OSFA or M-PG1, 6- inch o.c. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1, 6- inch o.c. SBS-TA (Optional) SBS-TA SBS-TA -232.5 C-12 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch DensDeck Prime M-OSFA or M-PG1 SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 56 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-13 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board M-OSFA or M-PG1 SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-14 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 CR-20 0.5-inch SECUROCK Cement Roof Board CR-20 SBS-TA (Optional) SBS-TA SBS-TA -187.5 C-15 Structural concrete None Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 C-16 Structural concrete None Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-TA (Optional) APP-TA APP-TA -232.5 C-17 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 CR-20, 6- inch o.c. 0.5-inch SECUROCK Cement Roof Board CR-20, 6- inch o.c. SBS-TA (Optional) SBS-TA SBS-TA -232.5 C-18 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-19 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board CR-20 SBS-TA, APP- TA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-20 Structural concrete None (Optional) Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB Classic (full- coverage) BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 C-21 Structural concrete None (Optional) Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB Classic (full- coverage) APP-TA (Optional) APP-TA APP-TA -232.5 C-22 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board Hot asphalt BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 57 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-23 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP-TA (Optional) APP-TA APP-TA -232.5 C-24 Structural concrete PG100 Min. 0.75-inch Fesco Board (homogeneous) Hot asphalt None N/A (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -277.5 C-25 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.75-inch Fesco Board (homogeneous) Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -290.0 C-26 Structural concrete PG100 Min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt None N/A (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -285.0 C-27 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -480.0 C-28 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck Prime Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -480.0 C-29 Structural concrete PG100 Min. 0.25-inch DensDeck Prime Hot asphalt None N/A (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -510.0 SELF-ADHERING BASE PLY TO INSULATION: C-30 Structural concrete (Optional) PG100 Min. 1.5-inch H-Shield or Multi-Max FA3 D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -67.5 C-31 Structural concrete None Min. 1.5-inch Polytherm H, H-Shield D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -122.5 C-32 Structural concrete (Optional) PG100 Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -135.0 C-33 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam D-IS (Optional) additional layers of base insulation D-IS SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -157.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 58 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-34 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 (Optional) additional layers of base insulation OB500 SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -120.0 C-35 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -122.5 C-36 Structural concrete None Min. 1.5-inch ENRGY 3 OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -127.5 C-37 Structural concrete None Min. 1.5-inch Polytherm H or H-Shield OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -150.0 C-38 Structural concrete None ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD OB500 None N/A SBS-SA (Optional) SBS-SA SBS-SA -230.0 C-39 Structural concrete None ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD OB500, 6- inch o.c. None N/A SBS-SA (Optional) SBS-SA SBS-SA -285.0 C-40 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield M-OSFA or M-PG1 (Optional) additional layers(s) of base insulation M-OSFA or M-PG1 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -122.5 C-41 Structural concrete None ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD M-OSFA or M-PG1 None N/A SBS-SA (Optional) SBS-SA SBS-SA -230.0 C-42 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA (Optional) additional layers(s) of base insulation M-OSFA SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -232.5 C-43 Structural concrete None ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD M-OSFA or M-PG1, 6- inch o.c. None N/A SBS-SA (Optional) SBS-SA SBS-SA -285.0 C-44 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax. M-OSFA or M-PG1 (Optional) additional layers(s) of base insulation, optionally primed with POLYBRITE 745 or WB3000 M-OSFA or M-PG1 SBS-SA None SBS-CA1, SBS- CA2 -290.0 C-45 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield CR-20 (Optional) additional layers(s) of base insulation CR-20 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -122.5 C-46 Structural concrete None ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20 None N/A SBS-SA (Optional) SBS-SA SBS-SA -230.0 C-47 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 (Optional) additional layers of base insulation CR-20 SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -240.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 59 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-48 Structural concrete None ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20, 6- inch o.c. None N/A SBS-SA (Optional) SBS-SA SBS-SA -285.0 C-49 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) (Optional) additional layers(s) of base insulation OB Classic (full- coverage) SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -270.0 C-50 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt (Optional) additional layers(s) of base insulation Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -480.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY TO INSULATION: C-51 Structural concrete (Optional) PG100 Min. 1.5-inch H-Shield or Multi-Max FA3 D-IS (Optional) additional layers(s) of base insulation D-IS APP-SA-H (Optional) APP-TA APP-TA -67.5 C-52 Structural concrete None Min. 1.5-inch Polytherm H, H-Shield D-IS (Optional) additional layers(s) of base insulation D-IS APP-SA-H (Optional) APP-TA APP-TA -122.5 C-53 Structural concrete (Optional) PG100 Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 D-IS (Optional) additional layers(s) of base insulation D-IS APP-SA-H (Optional) APP-TA APP-TA -135.0 C-54 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II OB500 (Optional) additional layers(s) of base insulation OB500 APP-SA-H (Optional) APP-TA APP-TA -122.5 C-55 Structural concrete None Min. 1.5-inch ENRGY 3 OB500 (Optional) additional layers(s) of base insulation OB500 APP-SA-H (Optional) APP-TA APP-TA -127.5 C-56 Structural concrete None Min. 1.5-inch Polytherm H or H-Shield OB500 (Optional) additional layers(s) of base insulation OB500 APP-SA-H (Optional) APP-TA APP-TA -150.0 C-57 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield M-OSFA or M-PG1 (Optional) additional layers(s) of base insulation M-OSFA or M-PG1 APP-SA-H (Optional) APP-TA APP-TA -122.5 C-58 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA (Optional) additional layers(s) of base insulation M-OSFA APP-SA-H (Optional) APP-TA APP-TA -232.5 C-59 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield CR-20 (Optional) additional layers(s) of base insulation CR-20 APP-SA-H (Optional) APP-TA APP-TA -122.5 C-60 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) (Optional) additional layers(s) of base insulation OB Classic (full- coverage) APP-SA-H (Optional) APP-TA APP-TA -270.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 60 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-61 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt (Optional) additional layers(s) of base insulation Hot asphalt APP-SA-H (Optional) APP-TA APP-TA -480.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY TO INSULATION: C-62 Structural concrete (Optional) PG100 Min. 1.5-inch H-Shield or Multi-Max FA3 D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -67.5 C-63 Structural concrete None Min. 1.5-inch Polytherm H, H-Shield D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -122.5 C-64 Structural concrete (Optional) PG100 Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -135.0 C-65 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -122.5 C-66 Structural concrete None Min. 1.5-inch ENRGY 3 OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -127.5 C-67 Structural concrete None Min. 1.5-inch Polytherm H or H-Shield OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -150.0 C-68 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield M-OSFA or M-PG1 (Optional) additional layers(s) of base insulation M-OSFA or M-PG1 SBS-SA-H (Optional) SBS-TA SBS-TA -122.5 C-69 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA (Optional) additional layers(s) of base insulation M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -232.5 C-70 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield CR-20 (Optional) additional layers(s) of base insulation CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -122.5 C-71 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) (Optional) additional layers(s) of base insulation OB Classic (full- coverage) SBS-SA-H (Optional) SBS-TA SBS-TA -270.0 C-72 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt (Optional) additional layers(s) of base insulation Hot asphalt SBS-SA-H (Optional) SBS-TA SBS-TA -480.0 SELF-ADHERING BASE PLY TO COVERBOARD: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 61 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-73 Structural concrete None Min. 1.5-inch Multi-Max FA3 D-IS Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -67.5 C-74 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam, Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield D-IS Min. 0.25-inch DensDeck Prime D-IS SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -72.5 C-75 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch DensDeck, DensDeck Prime D-IS SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -120.0 C-76 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 D-IS SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-77 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch DEXcell FA Glass Mat Roof Board D-IS SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-78 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -322.5 C-79 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or ISO 95+GL OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -72.5 C-80 Structural concrete None Min. 1.5-inch ENRGY 3 OB500 Min. 0.25-inch DensDeck, DensDeck Prime OB500 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -127.5 C-81 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, H- Shield or ISO 95+GL OB500 Min. 0.25-inch DensDeck, DensDeck Prime OB500 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -150.0 C-82 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or min. 2.0 pcf Insulfoam OB500 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD OB500 SBS-SA (Optional) SBS-SA SBS-SA -230.0 C-83 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-84 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD OB500, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -285.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 62 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-85 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch DEXcell FA Glass Mat Roof Board OB500 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-86 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 OB500 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -322.5 C-87 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch DensDeck Prime M-OSFA SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -72.5 C-88 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or min. 2.0 pcf Insulfoam M-OSFA or M-PG1 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD M-OSFA or M-PG1 SBS-SA (Optional) SBS-SA SBS-SA -230.0 C-89 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -232.5 C-90 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch DensDeck Prime M-OSFA or M-PG1 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-91 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD M-OSFA or M-PG1, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -285.0 C-92 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch DEXcell FA Glass Mat Roof Board M-OSFA or M-PG1 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-93 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 M-OSFA or M-PG1 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -322.5 C-94 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam, Min. 2-inch Polytherm, ACFoam II, min. 1.5-inch Ultra-Max or Multi-Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H- Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime CR-20 SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -72.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 63 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-95 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or min. 2.0 pcf Insulfoam CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD CR-20 SBS-SA (Optional) SBS-SA SBS-SA -230.0 C-96 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam, Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime CR-20 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -240.0 C-97 Structural concrete None Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -240.0 C-98 Structural concrete None Min. 1.5-inch min. 2.0 pcf Insulfoam CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD CR-20, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -240.0 C-99 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -282.5 C-100 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H- Shield HD CR-20, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -285.0 C-101 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DEXcell FA Glass Mat Roof Board CR-20 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5 C-102 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 CR-20 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -322.5 C-103 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB Classic (full- coverage) SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -350.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 64 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-104 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -350.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY TO COVERBOARD: C-105 Structural concrete None Min. 1.5-inch Multi-Max FA3 D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS APP-SA-H (Optional) APP-TA APP-TA -67.5 C-106 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch DensDeck, DensDeck Prime D-IS APP-SA-H (Optional) APP-TA APP-TA -120.0 C-107 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 or DEXcell FA Glass Mat Roof Board D-IS APP-SA-H (Optional) APP-TA APP-TA -322.5 C-108 Structural concrete None Min. 1.5-inch ENRGY 3 OB500 Min. 0.25-inch DensDeck, DensDeck Prime OB500 APP-SA-H (Optional) APP-TA APP-TA -127.5 C-109 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, H- Shield or ISO 95+GL OB500 Min. 0.25-inch DensDeck, DensDeck Prime OB500 APP-SA-H (Optional) APP-TA APP-TA -150.0 C-110 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board OB500 APP-SA-H (Optional) APP-TA APP-TA -322.5 C-111 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board M-OSFA or M-PG1 APP-SA-H (Optional) APP-TA APP-TA -322.5 C-112 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam, Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime CR-20 APP-SA-H (Optional) APP-TA APP-TA -240.0 C-113 Structural concrete None Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP-TA APP-TA -240.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 65 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-114 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board CR-20 APP-SA-H (Optional) APP-TA APP-TA -322.5 C-115 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB Classic (full- coverage) APP-SA-H (Optional) APP-TA APP-TA -350.0 C-116 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP-SA-H (Optional) APP-TA APP-TA -350.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY TO COVERBOARD: C-117 Structural concrete None Min. 1.5-inch Multi-Max FA3 D-IS Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -67.5 C-118 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch DensDeck, DensDeck Prime D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -120.0 C-119 Structural concrete None Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -247.5 C-120 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch DensDeck Prime optionally primed with POLYBRITE 745 or WB3000 D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -282.5 C-121 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board optionally primed with POLYBRITE 745 or WB3000 or DEXcell FA Glass Mat Roof Board D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -322.5 C-122 Structural concrete None Min. 1.5-inch ENRGY 3 OB500 Min. 0.25-inch DensDeck, DensDeck Prime OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -127.5 C-123 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, H- Shield or ISO 95+GL OB500 Min. 0.25-inch DensDeck, DensDeck Prime OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -150.0 C-124 Structural concrete None Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -247.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 66 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-125 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -282.5 C-126 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -322.5 C-127 Structural concrete None Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -232.5 C-128 Structural concrete None Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield M-OSFA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -247.5 C-129 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch DensDeck Prime M-OSFA or M-PG1 SBS-SA-H (Optional) SBS-TA SBS-TA -282.5 C-130 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield M-OSFA or M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board M-OSFA or M-PG1 SBS-SA-H (Optional) SBS-TA SBS-TA -322.5 C-131 Structural concrete None Min. 1.5-inch, min. 2.0 pcf Insulfoam, Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -240.0 C-132 Structural concrete None Min. 1.5-inch Ultra-Max or Multi-Max FA- 3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H-Shield CG or ENRGY 3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -240.0 C-133 Structural concrete None Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -247.5 C-134 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -282.5 C-135 Structural concrete None (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DEXcell FA Glass Mat Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -322.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 67 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-136 Structural concrete None Min. 2-inch Polytherm, ACFoam II, Polytherm H or H-Shield OB Classic (full- coverage) Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB Classic (full- coverage) SBS-SA-H (Optional) SBS-TA SBS-TA -350.0 C-137 Structural concrete PG100 Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 Hot asphalt Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA-H (Optional) SBS-TA SBS-TA -350.0 COLD-APPLIED BASE PLY: C-138 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H or H-Shield D-IS Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board D-IS SBS-CA1, SBS- CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 C-139 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H or H-Shield D-IS Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board D-IS SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-140 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H or H-Shield D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-141 Structural concrete None Min. 1-inch ENRGY 3, Polytherm H or H- Shield D-IS Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board D-IS SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2 -232.5 C-142 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-CA1, SBS- CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 68 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-143 Structural concrete None Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5- inch SECUROCK Cement Roof Board M-OSFA, M-PG1 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-144 Structural concrete None Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA, M-PG1 SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-145 Structural concrete None Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA, M-PG1 SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2 -232.5 C-146 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board OB500 SBS-CA1, SBS- CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 C-147 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board OB500 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-148 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-149 Structural concrete None Min. 1-inch Polytherm, ACFoam II, ENRGY 3 or Multi-Max FA3 OB500 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board OB500 SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2 -232.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 69 of 98 TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 16 System No. Deck (Note 1) Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply C-150 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS- CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 C-151 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board CR-20 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-152 Structural concrete None Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 C-153 Structural concrete None Min. 1-inch ENRGY 3, Polytherm H, H- Shield, Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS- CA2 None SBS-CA1, SBS- CA2 -232.5 TABLE 3B: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE F: NON-INSULATED, BONDED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Primer Roof Cover (Note 15) MDP (psf) Base Ply Ply Cap Ply ASPHALT- OR TORCH-APPLIED BASE PLY: C-154 Structural concrete PG100 (Optional) SBS-TA (Optional) SBS-TA SBS-TA -495.0 C-155 Structural concrete PG100 BP-AA (Optional if using asphalt applied Ply) (Optional if using asphalt applied Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -622.5 SELF-ADHERING BASE PLY: C-156 Structural concrete PG100 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -315.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: C-157 Structural concrete PG100 APP-SA-H (Optional) APP-TA APP-TA -315.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: C-158 Structural concrete PG100 SBS-SA-H (Optional) SBS-TA SBS-TA -315.0 COLD-APPLIED BASE PLY: C-159 Structural concrete None SBS-CA1 None SBS-CA1, SBS-CA2, APP-CA1 -105.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 70 of 98 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Insulation Layer Coverboard Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply CELCORE (FL2037): ASPHALT OR TORCH APPLIED BASE PLY: LWC-1 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 BP-AA, SBS- AA, APP-TA (Optional) BP- AA, SBS-AA, SBS-TA or APP- TA SBS-AA, SBS- TA, APP-TA -222.5 SELF-ADHERING BASE PLY: LWC-2 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA (Optional) SBS- SA SBS-SA, APP- SA -222.5 LWC-3 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -222.5 LWC-4 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -222.5 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: LWC-5 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 APP-SA-H (Optional) APP- TA APP-TA -222.5 LWC-6 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP- TA APP-TA -222.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: LWC-7 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA-H (Optional) SBS- TA SBS-TA -222.5 LWC-8 Structural concrete Min. 200 psi, min. 2-inch Celcore Cellular Concrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS- TA SBS-TA -222.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 71 of 98 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Insulation Layer Coverboard Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ELASTIZELL (FL4994): ASPHALT OR TORCH APPLIED BASE PLY: LWC-9 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 BP-AA, SBS- AA, APP-TA (Optional) BP- AA, SBS-AA, SBS-TA or APP- TA SBS-AA, SBS- TA, APP-TA -225.0 LWC-10 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 BP-AA, SBS- AA, APP-TA (Optional) BP- AA, SBS-AA, SBS-TA or APP- TA SBS-AA, SBS- TA, APP-TA -180.0 SELF-ADHERING BASE PLY: LWC-11 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 (Optional) Additional layers of base insulation OB500 SBS-SA (Optional) SBS- SA SBS-SA, APP- SA -120.0 LWC-12 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -120.0 LWC-13 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 (Optional) Additional layers of base insulation OB500 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -225.0 LWC-14 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -225.0 LWC-15 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA (Optional) SBS- SA SBS-SA, APP- SA -180.0 LWC-16 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -180.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 72 of 98 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Insulation Layer Coverboard Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply LWC-17 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -180.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: LWC-18 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 APP-SA-H (Optional) APP- TA APP-TA -120.0 LWC-19 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 (Optional) Additional layers of base insulation OB500 APP-SA-H (Optional) APP- TA APP-TA -225.0 LWC-20 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 APP-SA-H (Optional) APP- TA APP-TA -225.0 LWC-21 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 APP-SA-H (Optional) APP- TA APP-TA -180.0 LWC-22 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP- TA APP-TA -180.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: LWC-23 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA-H (Optional) SBS- TA SBS-TA -120.0 LWC-24 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 (Optional) Additional layers of base insulation OB500 SBS-SA-H (Optional) SBS- TA SBS-TA -225.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 73 of 98 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Insulation Layer Coverboard Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply LWC-25 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, ISO 95+ GL, Polytherm H or H-Shield OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA-H (Optional) SBS- TA SBS-TA -225.0 LWC-26 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA-H (Optional) SBS- TA SBS-TA -180.0 LWC-27 Structural concrete Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete. Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS- TA SBS-TA -180.0 MEARLCRETE (FL13492): ASPHALT OR TORCH APPLIED BASE PLY: LWC-28 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 BP-AA, SBS- AA, APP-TA (Optional) BP- AA, SBS-AA, SBS-TA or APP- TA SBS-AA, SBS- TA, APP-TA -222.5 SELF-ADHERING BASE PLY: LWC-29 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA (Optional) SBS- SA SBS-SA, APP- SA -222.5 LWC-30 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -222.5 LWC-31 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -222.5 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: LWC-32 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 APP-SA-H (Optional) APP- TA APP-TA -222.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 74 of 98 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Insulation Layer Coverboard Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply LWC-33 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP- TA APP-TA -222.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: LWC-34 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 CR-20 (Optional) Additional layers of base insulation CR-20 SBS-SA-H (Optional) SBS- TA SBS-TA -222.5 LWC-35 Structural concrete Min. 200 psi, min. 2-inch Mearlcrete Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, ISO 95+ GL, Polytherm H, H-Shield, H-Shield CG, Multi- Max FA3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS- TA SBS-TA -222.5 TABLE 4B: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Anchor Sheet Temp Roof Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply LWC-36 Min. 22 ga., Type B, vented steel at max. 5 ft spans Min. 300 psi, min. 2-inch Celcore Cellular Concrete, Elastizell Lightweight Insulating Concrete or Mearlcrete GAFGLAS #75 or Elastovent OMG CR BSF 7-inch o.c. at min. 4-inch lap and 7- inch o.c. at two, equally spaced center rows (Optional) SBS-TA (sanded- top- surface) (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield, Multi-Max FA3 or Polytherm HA Min. 1.5-inch Thermaroof Composite, Polytherm Composite, or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation or min. 0.75-inch Fesco Board (homogeneous) HA (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP- AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 75 of 98 TABLE 4B: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Anchor Sheet Temp Roof Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply LWC-37 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture Elastobase V, Elastobase P or Elastovent Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8- inch o.c. at three equally spaced, staggered center rows SBS-TA (sanded- top- surface) Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H- Shield CG, Multi-Max FA3 or ENRGY-3 M-OSFA, 6-inch o.c. Additional Insulation Layer(s): (Optional) Min. 0.5- inch base insulation flat or tapered Coverboard: Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Additional Layer(s): M- OSFA, 4-inch o.c. Coverboard: M-OSFA, 6- inch o.c. BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -60.0* LWC-38 Min. 22 ga., Type B, vented steel at max. 5 ft spans Min. 300 psi, min. 2-inch Celcore Cellular Concrete, Elastizell Lightweight Insulating Concrete or Mearlcrete GAFGLAS #75 or Elastovent OMG CR BSF 7-inch o.c. at min. 4-inch lap and 7- inch o.c. at two, equally spaced center rows (Optional) SBS-TA (sanded- top- surface) Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield, Multi-Max FA3 or Polytherm HA None N/A SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -45.0 LWC-39 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture Elastobase V, Elastobase P or Elastovent Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8- inch o.c. at three equally spaced, staggered center rows SBS-TA (sanded- top- surface) Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H- Shield CG, Multi-Max FA3 or ENRGY-3 M-OSFA, 6-inch o.c. (Optional) Additional layers of base insulation, min. 0.5-inch, flat or tapered M-OSFA, 4- inch o.c. SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -60.0* LWC-40 Min. 22 ga., Type B, vented steel at max. 5 ft spans Min. 300 psi, min. 2-inch Celcore Cellular Concrete, Elastizell Lightweight Insulating Concrete or Mearlcrete GAFGLAS #75 or Elastovent OMG CR BSF 7-inch o.c. at min. 4-inch lap and 7- inch o.c. at two, equally spaced center rows (Optional) SBS-TA (sanded- top- surface) Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield, Multi-Max FA3 or Polytherm HA None N/A APP-SA-H (Optional) APP-TA APP-TA -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 76 of 98 TABLE 4B: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Anchor Sheet Temp Roof Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply LWC-41 Min. 22 ga., Type B, vented steel at max. 5 ft spans Min. 300 psi, min. 2-inch Celcore Cellular Concrete, Elastizell Lightweight Insulating Concrete or Mearlcrete GAFGLAS #75 or Elastovent OMG CR BSF 7-inch o.c. at min. 4-inch lap and 7- inch o.c. at two, equally spaced center rows (Optional) SBS-TA (sanded- top- surface) Min. 1.5-inch Polytherm, ACFoam II, Polytherm H, H-Shield, Multi-Max FA3 or Polytherm HA None N/A SBS-SA-H (Optional) SBS-TA SBS-TA -45.0 LWC-42 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture Elastobase V, Elastobase P or Elastovent Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8- inch o.c. at three equally spaced, staggered center rows SBS-TA (sanded- top- surface) Min. 2-inch Polytherm, ACFoam II, III, Polytherm H, H-Shield, H- Shield CG, Multi-Max FA3 or ENRGY-3 M-OSFA, 6-inch o.c. (Optional) Additional layers of base insulation, min. 0.5-inch, flat or tapered M-OSFA, 4- inch o.c. SBS-SA-H (Optional) SBS-TA SBS-TA -60.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 77 of 98 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Sheet (Note A below) Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply PRE-EXISTENT CELLULAR LWC: LWC-43 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick pre-existent cellular lightweight concrete. Note: To qualify the LWIC under this assembly, an OMG CR BPF shall achieve an average withdrawal of 53 lbf when tested per TAS 105 or ANSI/SPRI FX-1 B3 or B11 OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet (Optional) BP-AA, SBS-AA SBS-AA, APP- TA -45.0 CELCORE (FL2037): ASPHALT OR TORCH APPLIED BASE PLY: LWC-44 Min. 0.0179-inch Tensilform S- 75 or min. 0.0205-inch Tensilform 75 at max. 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Celcore Cellular Concrete B1, B2, B3, B7 or B11 Trufast FM-90 or OMG CR BPF 8-inch o.c. at a min. 3-inch lap and 16-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA SBS-AA -37.5 LWC-45 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Celcore Cellular Concrete B1 through B11 Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA SBS-AA -45.0 LWC-46 Min. 26 ga., type HF steel at max 5 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B1, B2, B3, B4, B7, B8, B10 or B11 OMG CR BPF 9-inch o.c. at a min. 3-inch lap and 9-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA SBS-AA -45.0 LWC-47 Min. 22 ga., type B steel at max 6 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B1, B2, B3, B4, B7, B8, B10 or B11 OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 14-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA SBS-AA -45.0 LWC-48 Min. 22 ga., type B steel at max 6 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B1, B2, B3, B4, B7, B8, B10 or B11 OMG CR BPF 9-inch o.c. at a min. 3-inch lap and 9-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA SBS-AA -45.0 LWC-49 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B1, B2 or B11 Trufast Twin Loc- Nail 9-inch o.c. at a min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, or APP- TA -45.0 LWC-50 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast Twin Loc- Nail 9-inch o.c. at a min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-TA or APP-TA SBS-TA or APP-TA -45.0 LWC-51 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 or B11 Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8-inch o.c. at three equally spaced, staggered center rows BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, or APP- TA -60.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 78 of 98 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Sheet (Note A below) Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply LWC-52 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8-inch o.c. at three equally spaced, staggered center rows SBS-TA or APP-TA SBS-TA or APP-TA -60.0 LWC-53 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore Cellular Concrete B1 through B11 Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA, SBS-TA, APP-TA SBS-AA, APP- TA -75.0 LWC-54 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture Elastobase P Trufast FM-290 10-inch o.c. at a min. 4-inch lap and 10-inch o.c. at three equally spaced, staggered center rows (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -90.0 SELF-ADHERING BASE PLY: LWC-55 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast Twin Loc- Nail 9-inch o.c. at a min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -45.0 LWC-56 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8-inch o.c. at three equally spaced, staggered center rows SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -60.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: LWC-57 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast Twin Loc- Nail 9-inch o.c. at a min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered rows in the field of the sheet APP-SA-H APP-TA -45.0 LWC-58 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8-inch o.c. at three equally spaced, staggered center rows APP-SA-H APP-TA -60.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: LWC-59 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 225 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast Twin Loc- Nail 9-inch o.c. at a min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA-H SBS-TA -45.0 LWC-60 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture B2 (with poly- film top surface) Trufast FM-90 8-inch o.c. at a min. 4-inch lap and 8-inch o.c. at three equally spaced, staggered center rows SBS-SA-H SBS-TA -60.0 ELASTIZELL (FL4994): ASPHALT OR TORCH APPLIED BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 79 of 98 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Sheet (Note A below) Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply LWC-61 Min. 0.0179-inch Tensilform S- 75 or min. 0.0205-inch Tensilform 75 at max. 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B1 through B11 Trufast FM-90 or OMG CR BPF 7.5-inch o.c. at a min. 3-inch lap and 7.5-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA, SBS-TA, or APP-TA SBS-AA, SBS- TA, or APP- TA -30.0 LWC-62 Min. 0.0179-inch Tensilform S- 75 or min. 0.0205-inch Tensilform 75 at max. 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7.5-inch o.c. at a min. 3-inch lap and 7.5-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-TA or APP-TA SBS-TA or APP-TA -30.0 LWC-63 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B1 through B11 Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA, SBS-TA, or APP-TA SBS-AA, SBS- TA, or APP- TA -45.0 LWC-64 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-TA or APP-TA SBS-TA or APP-TA -45.0 LWC-65 Min. 22 ga., type B vented steel at max 5 ft spans or structural concrete Min. 350 psi, min. 2-inch thick Elastizell with Zell-Crete Fibers, supplemental attached with Roofgrip #21 and 3-inch plates at 1 per 8 ft2 Elastobase P (with poly-film top surface) Trufast FM-290 8-inch o.c. at a min. 4-inch lap and 8-inch o.c. at three, equally spaced, staggered rows in the field of the sheet (Optional) BP-AA, SBS-AA, SBS-TA, or APP-TA SBS-AA, SBS- TA, or APP- TA -52.5 LWC-66 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 350 psi, min. 2-inch thick Elastizell with Zell-Crete Fibers, supplemental attached with Roofgrip #21 and 3-inch plates at 1 per 8 ft2 B2 or B11 Trufast Twin Loc- Nails (min. 1.8- inch) 6-inch o.c. at a min. 4-inch lap and 6-inch o.c. at three, equally spaced, staggered rows in the field of the sheet BP-AA or SBS-AA SBS-AA, SBS- TA, SBS-SA, APP-TA or APP-SA -60.0 LWC-67 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 350 psi, min. 2-inch thick Elastizell with Zell-Crete Fibers, supplemental attached with Roofgrip #21 and 3-inch plates at 1 per 8 ft2 B2 (with poly- film top surface) Trufast Twin Loc- Nails (min. 1.8- inch) 6-inch o.c. at a min. 4-inch lap and 6-inch o.c. at three, equally spaced, staggered rows in the field of the sheet SBS-TA or APP-TA SBS-TA or APP-TA -60.0 SELF-ADHERING BASE PLY: LWC-68 Min. 0.0179-inch Tensilform S- 75 or min. 0.0205-inch Tensilform 75 at max. 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7.5-inch o.c. at a min. 3-inch lap and 7.5-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -30.0 LWC-69 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -45.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 80 of 98 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Sheet (Note A below) Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply LWC-70 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 350 psi, min. 2-inch thick Elastizell with Zell-Crete Fibers, supplemental attached with Roofgrip #21 and 3-inch plates at 1 per 8 ft2 B2 (with poly- film top surface) Trufast Twin Loc- Nails (min. 1.8- inch) 6-inch o.c. at a min. 4-inch lap and 6-inch o.c. at three, equally spaced, staggered rows in the field of the sheet SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -60.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: LWC-71 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet APP-SA-H APP-TA -45.0 LWC-72 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 350 psi, min. 2-inch thick Elastizell with Zell-Crete Fibers, supplemental attached with Roofgrip #21 and 3-inch plates at 1 per 8 ft2 B2 (with poly- film top surface) Trufast Twin Loc- Nails (min. 1.8- inch) 6-inch o.c. at a min. 4-inch lap and 6-inch o.c. at three, equally spaced, staggered rows in the field of the sheet APP-SA-H APP-TA -60.0 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: LWC-73 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Range II Elastizell Lightweight Insulating Concrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 3-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA-H SBS-TA -45.0 LWC-74 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 350 psi, min. 2-inch thick Elastizell with Zell-Crete Fibers, supplemental attached with Roofgrip #21 and 3-inch plates at 1 per 8 ft2 B2 (with poly- film top surface) Trufast Twin Loc- Nails (min. 1.8- inch) 6-inch o.c. at a min. 4-inch lap and 6-inch o.c. at three, equally spaced, staggered rows in the field of the sheet SBS-SA-H SBS-TA -60.0 MEARLCRETE (FL13492): ASPHALT OR TORCH APPLIED BASE PLY: LWC-75 Min. 24 ga., type B steel at max 5 ft spans or structural concrete Min. 200 psi, min. 2-inch thick Mearlcrete B1 through B11 Trufast FM-90 or OMG CR BPF 7.5-inch o.c. at a min. 3-inch lap and 10-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA SBS-AA -30.0 LWC-76 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Mearlcrete B1, B2, B3, B7 or B11 Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 4-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet BP-AA, SBS-AA, SBS-TA, or APP-TA SBS-AA, SBS- TA, or APP- TA -52.5 LWC-77 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Mearlcrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 4-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-TA or APP-TA SBS-TA or APP-TA -52.5 SELF-ADHERING BASE PLY: LWC-78 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Mearlcrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 4-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA SBS-SA, APP- SA, SBS-TA or APP-TA -52.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 81 of 98 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E-2: MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Lightweight Concrete (Note 14) Base Sheet (Note A below) Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: LWC-79 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Mearlcrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 4-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet APP-SA-H APP-TA -52.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: LWC-80 Min. 22 ga., type B steel at max 5 ft spans or structural concrete Min. 300 psi, min. 2-inch thick Mearlcrete B2 (with poly- film top surface) Trufast FM-90 or OMG CR BPF 7-inch o.c. at a min. 4-inch lap and 7-inch o.c. at two, equally spaced, staggered rows in the field of the sheet SBS-SA-H SBS-TA -52.5 A. Base Sheets options in Table 4C are coded as follows: ➢ B1: Polyglass G2 Base; B2: Elastobase V or Elastobase P; B3: GAFGLAS #75; B4: GAFGLAS Stratavent Nailable Venting Base Sheet; B5: GAFGLAS Ply 4; B6: GAFGLAS FlexPly 6; B7: JM Perma Ply No. 28; B8: JM Vensulation; B9: JM GlasPly IV; B10: JM GlasPly Premier; B11: Elastovent NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 82 of 98 TABLE 5A: CEMENTITIOUS WOOD FIBER DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT OR TORCH APPLIED BASE PLY: CWF-1 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 D-IS or OB500 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation D-IS or OB500 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -45.0 CWF-2 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 D-IS or OB500 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board D-IS or OB500 SBS-TA or APP- TA (Optional) SBS-TA or APP-TA SBS-TA, APP-TA -45.0 CWF-3 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation CR-20 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -52.5 CWF-4 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-TA or APP- TA (Optional) SBS-TA or APP-TA SBS-TA, APP-TA -52.5 CWF-5 Tectum Plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS- TA, APP-TA -75.0 CWF-6 Tectum Plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-TA or APP- TA (Optional) SBS-TA or APP-TA SBS-TA, APP-TA -75.0 SELF-ADHERING BASE PLY: CWF-7 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 D-IS or OB500 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board D-IS or OB500 SBS-SA (Optional) SBS-SA, SBS-TA or APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -45.0 CWF-8 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS-SA, SBS-TA or APP-TA SBS-SA, APP- SA, SBS-TA, APP-TA -52.5 CWF-9 Tectum Plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -75.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 83 of 98 TABLE 5A: CEMENTITIOUS WOOD FIBER DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply CWF-10 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 D-IS or OB500 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board D-IS or OB500 APP-SA-H (Optional) APP-TA APP-TA -45.0 CWF-11 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP-TA APP-TA -52.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: CWF-12 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 D-IS or OB500 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board D-IS or OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -45.0 CWF-13 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 1.5-inch Polytherm, ACFoam II, ISO 95+GL, Polytherm H, H-Shield, ENRGY-3 CR-20 Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -52.5 CWF-14 Tectum Plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -75.0 TABLE 5B: CEMENTITIOUS WOOD FIBER DECKS – REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT OR TORCH APPLIED BASE PLY: CWF-15 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast Twin Loc-Nail 9-inch o.c. at min. 4-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ISO95+GL, Polytherm H, H- Shield, ENRGY 3 or Multi-Max FA3, Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board, Min. 0.75- inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA, SBS-AA (Optional) BP- AA, SBS-AA, SBS-TA or APP- TA SBS-AA, SBS-TA, APP-TA -45.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 84 of 98 TABLE 5B: CEMENTITIOUS WOOD FIBER DECKS – REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply CWF-16 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast Twin Loc-Nail 9-inch o.c. at min. 4-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ISO95+GL, Polytherm H, H-Shield, ENRGY 3 or Multi-Max FA3, Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-TA or APP- TA (Optional) SBS- TA or APP-TA SBS-TA, APP-TA -45.0* SELF-ADHERING BASE PLY: CWF-17 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast Twin Loc-Nail 9-inch o.c. at min. 4-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ISO95+GL, Polytherm H, H-Shield, ENRGY 3 or Multi-Max FA3, Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA (Optional) SBS- TA, SBS-SA or APP-TA SBS-TA, SBS-SA, APP-TA, APP-SA -45.0* HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: CWF-18 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast Twin Loc-Nail 9-inch o.c. at min. 4-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ISO95+GL, Polytherm H, H-Shield, ENRGY 3 or Multi-Max FA3, Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt APP-SA- H (Optional) APP- TA APP-TA -45.0* HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: CWF-19 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast Twin Loc-Nail 9-inch o.c. at min. 4-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ISO95+GL, Polytherm H, H-Shield, ENRGY 3 or Multi-Max FA3, Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board Hot asphalt SBS-SA- H (Optional) SBS- TA SBS-TA -45.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 85 of 98 TABLE 5C: CEMENTITIOUS WOOD FIBER DECKS – REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply CWF-20 Existing Min. 2.5-inch Tectum Plank or Tectum LS Plank Min. 2-inch H- Shield or Polytherm H OMG Polymer GypTec Plate with Polymer GypTec or Trufast TL 3 in. Plate with TL Fastener 1 per 4.0 ft2 Min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* TABLE 5D: CEMENTITIOUS WOOD FIBER DECKS – REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply CWF-21 Existing Min. 2.5- inch Tectum Plank or Tectum LS Plank (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board or min. 0.5- inch Structodek High Density Fiberboard Roof Insulation Trufast Twin Loc- Nails (min. 1-inch embedment) 1 per 2.0 ft2 (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* TABLE 5E: CEMENTITIOUS WOOD FIBER DECKS – REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E-2: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply CWF-22 Existing Min. 2.5- inch Tectum Plank or Tectum LS Plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast Twin Loc-Nails 9-inch o.c. at min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered center rows (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 86 of 98 TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT- OR TORCH-APPLIED BASE PLY: G-1 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 None N/A (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -245.0 G-2 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or Styrofoam Brand Roofmate, Highload 60 or Plazamate CR-20 0.5-inch SECUROCK Cement Roof Board CR-20 SBS-TA (Optional) SBS-TA SBS-TA -187.5 G-3 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or Styrofoam Brand Roofmate, Highload 60 or Plazamate CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA SBS-AA -225.0 G-4 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or Styrofoam Brand Roofmate, Highload 60 or Plazamate CR-20, 6- inch o.c. 0.5-inch SECUROCK Cement Roof Board CR-20, 6- inch o.c. SBS-TA (Optional) SBS-TA SBS-TA -232.5 G-5 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or Styrofoam Brand Roofmate, Highload 60 or Plazamate CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-TA, APP-TA (Optional) SBS- TA, APP-TA SBS-TA, APP-TA -282.5 G-6 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or Styrofoam Brand Roofmate, Highload 60 or Plazamate CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-TA, APP-TA (Optional) SBS- TA, APP-TA SBS-TA, APP-TA -322.5 SELF-ADHERING BASE PLY: G-7 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf, Insulfoam OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 G-8 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch DensDeck Prime OB500 None N/A SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 G-9 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch min. 2.0 pcf, Insulfoam OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA (Optional) SBS-SA SBS-SA, APP-SA -112.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 87 of 98 TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply G-10 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -112.5 G-11 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf, Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -112.5 G-12 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 None N/A SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -112.5 G-13 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch DensDeck Prime M-OSFA SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 G-14 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch DensDeck Prime M-OSFA None N/A SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 G-15 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Multi-Max FA3 M-OSFA (Optional) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board M-OSFA SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -202.5 G-16 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA None N/A SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -202.5 G-17 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch, min. 2.0 pcf EPS insulation board, Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 G-18 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch DensDeck Prime CR-20 None N/A SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 G-19 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield or min. 2.0 pcf Insulfoam CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20 SBS-SA (Optional) SBS-SA SBS-SA -230.0 G-20 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 (Optional) additional layers of base insulation CR-20 SBS-SA (Optional) SBS-SA SBS-SA -240.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 88 of 98 TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply G-21 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -240.0 G-22 Existing, sound poured gypsum or gypsum plank Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 None N/A SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -240.0 G-23 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch min. 2.0 pcf Insulfoam CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -240.0 G-24 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H- Shield CG or Multi-Max FA3 CR-20 (Optional) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 SBS-SA (Optional) SBS- SA, SBS-TA, APP- TA SBS-SA, APP-SA, SBS-TA, APP-TA -257.5 G-25 Existing, sound poured gypsum or gypsum plank (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H-Shield CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -285.0 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: G-26 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield OB500 (Optional) additional layers(s) of base insulation OB500 APP-SA-H (Optional) APP- TA APP-TA -112.5 G-27 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf, Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 APP-SA-H (Optional) APP- TA APP-TA -112.5 G-28 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Multi-Max FA3 M-OSFA (Optional) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board M-OSFA APP-SA-H (Optional) APP- TA APP-TA -202.5 G-29 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP- TA APP-TA -240.0 G-30 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H- Shield CG or Multi-Max FA3 CR-20 (Optional) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 APP-SA-H (Optional) APP- TA APP-TA -257.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 89 of 98 TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply G-31 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf, Insulfoam OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 G-32 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield OB500 (Optional) additional layers(s) of base insulation OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -112.5 G-33 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf, Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -112.5 G-34 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch DensDeck Prime M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 G-35 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H- Shield or Multi-Max FA3 M-OSFA (Optional) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -202.5 G-36 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch, min. 2.0 pcf EPS insulation board, Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H-Shield CG or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 G-37 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch, min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -240.0 G-38 Existing, sound poured gypsum or gypsum plank Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield, H- Shield CG or Multi-Max FA3 CR-20 (Optional) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -257.5 COLD APPLIED BASE PLY: G-39 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield ISO 95+ GL, Multi- Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 90 of 98 TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Deck (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply G-40 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2- inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5- inch SECUROCK Cement Roof Board M-OSFA SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 G-41 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2- inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 G-42 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2- inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2 -202.5 G-43 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board OB500 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -112.5 G-44 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 (Optional) SBS- CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 G-45 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board CR-20 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 G-46 Existing, sound poured gypsum or gypsum plank Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 G-47 Existing, sound poured gypsum or gypsum plank Min. 1-inch ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2 -232.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 91 of 98 TABLE 6B: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply G-48 Existing, sound poured gypsum or gypsum plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast FM-75 or FM-90 or Twin Loc- Nails 9-inch o.c. at min. 4-inch lap and 18- inch o.c. at two, equally spaced, staggered center rows Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ISO95+GL, Polytherm H, H-Shield, ENRGY 3 or Multi-Max FA3 Hot asphalt Min. 0.25-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board, Min. 0.75-inch Fesco Board (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard Roof Insulation Hot asphalt BP-AA, SBS-AA (Optional) BP-AA, SBS- AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* TABLE 6C: GYPSUM DECKS – REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System No. Deck (Note 1) Base Insulation Layer (Note 13) Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Ply Cap Ply G-49 Existing sound poured gypsum or gypsum plank (Optional) One or more layers, any combination, loose laid Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board or min. 0.5- inch Structodek High Density Fiberboard Roof Insulation Trufast Twin Loc- Nails (min. 1-inch embedment) 1 per 2.0 ft2 (Optional if using AA Ply) BP-AA, SBS-AA (Optional if using AA Base) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* TABLE 6D: GYPSUM DECKS – REROOF (TEAR-OFF) SYSTEM TYPE E: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER System No. Deck (Note 1) Base Sheet Roof Cover (Note 15) MDP (psf) Type Fasten (Note 11) Attach Base Ply Cap Ply G-50 Existing sound poured gypsum or gypsum plank Elastobase V, Elastobase P, Elastovent or Polyglass G2 Base Trufast FM-75 or FM- 90 or Twin Loc-Nails 9-inch o.c. at min. 4-inch lap and 18-inch o.c. at two, equally spaced, staggered center rows (Optional) BP-AA, SBS-AA, SBS- TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0* NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 92 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply ASPHALT OR TORCH APPLIED BASE PLY: R-1 Existing asphaltic roof (Optional) Min. 1.5-inch Multi-Max FA3 D-IS Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board D-IS BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA or APP-TA SBS-AA, SBS-TA or APP-TA -67.5 R-2 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 or min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board D-IS BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA or APP-TA SBS-AA, SBS-TA, or APP-TA -90.0 R-3 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or ISO 95+GL OB500 Min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board OB500 BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA or APP-TA SBS-AA, SBS-TA, or APP-TA -127.5 R-4 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board M-OSFA BP-AA, SBS- AA, SBS-TA, APP-TA (Optional) BP-AA, SBS- AA, SBS-TA or APP-TA SBS-AA, SBS-TA, or APP-TA -157.5 R-5 Existing asphaltic roof (Optional) Min. 1.5-inch Ultra-Max or Multi- Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H- Shield, H-Shield CG or ENRGY 3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 BP-AA, SBS- AA (Optional) BP-AA, SBS- AA SBS-AA -225.0 R-6 Existing asphaltic roof (Optional) Min. 1.5-inch Ultra-Max or Multi- Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H- Shield, H-Shield CG or ENRGY 3 or min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 APP-TA (Optional) APP-TA APP-TA -232.5 SELF-ADHERING BASE PLY: R-7 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Multi-Max FA3 D-IS (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DensDeck Prime D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -67.5 R-8 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3 or Multi-Max FA3 or min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch DensDeck Prime D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 R-9 Existing asphaltic roof Min. 1.5-inch min. 2.0 pcf Insulfoam D-IS (Optional) additional layers(s) of base insulation D-IS SBS-SA (Optional) SBS-SA SBS-SA -90.0 R-10 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -90.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 93 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply R-11 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 D-IS (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -90.0 R-12 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 R-13 Existing asphaltic roof Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 (Optional) additional layers of base insulation OB500 SBS-SA (Optional) SBS-SA SBS-SA -120.0 R-14 Existing asphaltic roof (Optional) Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board OB500 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -120.0 R-15 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield OB500 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -127.5 R-16 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield or min. 2.0 pcf Insulfoam OB500 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD OB500 SBS-SA (Optional) SBS-SA SBS-SA -127.5 R-17 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch DensDeck Prime M-OSFA SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 R-18 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -157.5 R-19 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield or min. 2.0 pcf Insulfoam M-OSFA or M-PG1 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD M-OSFA or M-PG1 SBS-SA (Optional) SBS-SA SBS-SA -157.5 R-20 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam, Min. 2-inch Polytherm, ACFoam II, min. 1.5-inch Ultra-Max or Multi-Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H- Shield CG or ENRGY 3 CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -72.5 R-21 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield or min. 2.0 pcf Insulfoam CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20 SBS-SA (Optional) SBS-SA SBS-SA -230.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 94 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply R-22 Existing asphaltic roof Min. 1.5-inch min. 2.0 pcf Insulfoam CR-20 (Optional) additional layers(s) of base insulation CR-20 SBS-SA (Optional) SBS-SA SBS-SA -240.0 R-23 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -240.0 R-24 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Ultra-Max or Multi-Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H- Shield CG or ENRGY 3 CR-20 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -240.0 R-25 Existing asphaltic roof Min. 1.5-inch, min. 2.0 pcf Insulfoam IX CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -240.0 R-26 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield CR-20 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA (Optional) SBS-SA, SBS-TA, APP-TA SBS-SA, APP-SA, SBS-TA, APP-TA -247.5 R-27 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, Polytherm H, H- Shield CR-20 ACFoam-HD Coverboard, ACFoam-HD Coverboard-FR or H-Shield HD CR-20, 6- inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -262.5 HYBRID SYSTEMS WITH SELF-ADHERING APP BASE PLY: R-28 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Multi-Max FA3 D-IS (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DensDeck Prime D-IS APP-SA-H (Optional) APP-TA APP-TA -67.5 R-29 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board D-IS APP-SA-H (Optional) APP-TA APP-TA -90.0 R-30 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 D-IS (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS APP-SA-H (Optional) APP-TA APP-TA -90.0 R-31 Existing asphaltic roof (Optional) Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board OB500 APP-SA-H (Optional) APP-TA APP-TA -120.0 R-32 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield OB500 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 APP-SA-H (Optional) APP-TA APP-TA -127.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 95 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply R-33 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA (Optional if Base Layer Insulation installed l) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA APP-SA-H (Optional) APP-TA APP-TA -157.5 R-34 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Ultra-Max or Multi-Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H- Shield CG or ENRGY 3 CR-20 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP-TA APP-TA -240.0 R-35 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield CR-20 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 APP-SA-H (Optional) APP-TA APP-TA -247.5 HYBRID SYSTEMS WITH SELF-ADHERING SBS BASE PLY: R-36 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Multi-Max FA3 D-IS (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or DensDeck Prime D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -67.5 R-37 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3 or Multi-Max FA3 or min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch DensDeck Prime D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 R-38 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam D-IS Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -90.0 R-39 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II or ENRGY 3 D-IS (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board D-IS SBS-SA-H (Optional) SBS-TA SBS-TA -90.0 R-40 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield or min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch DensDeck Prime OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 R-41 Existing asphaltic roof (Optional) Min. 1.5-inch, min. 2.0 pcf Insulfoam OB500 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -120.0 R-42 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, Polytherm H or H-Shield OB500 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA-H (Optional) SBS-TA SBS-TA -127.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 96 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply R-43 Existing asphaltic roof (Optional) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA Min. 0.25-inch DensDeck Prime M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 R-44 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Polytherm, ACFoam II, ENRGY 3, H-Shield or Multi-Max FA3 M-OSFA (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board M-OSFA SBS-SA-H (Optional) SBS-TA SBS-TA -157.5 R-45 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam, Min. 2-inch Polytherm, ACFoam II, min. 1.5-inch Ultra-Max or Multi-Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H- Shield CG or ENRGY 3 CR-20 Min. 0.25-inch DensDeck Prime CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -72.5 R-46 Existing asphaltic roof (Optional) Min. 1.5-inch min. 2.0 pcf Insulfoam CR-20 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -240.0 R-47 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 1.5-inch Ultra-Max or Multi-Max FA-3, min. 1.3-inch Polytherm G, ACFoam III or min. 1.0-inch ISO 95+GL, Polytherm H, H-Shield, H- Shield CG or ENRGY 3 CR-20 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -240.0 R-48 Existing asphaltic roof (Optional if Top Layer Insulation installed) Min. 2-inch Polytherm, ACFoam II, ENRGY-3, Polytherm H or H-Shield CR-20 (Optional if Base Layer Insulation installed) additional layers(s) of base insulation and/or min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA-H (Optional) SBS-TA SBS-TA -247.5 COLD APPLIED BASE PLY: R-49 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H or H-Shield D-IS Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board D-IS SBS-CA1, SBS-CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -90.0 R-50 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H-Shield ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA or M-PG1 SBS-CA1, SBS-CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 97 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply R-51 Existing asphaltic roof (Optional) Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H- Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA, M- PG1 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 R-52 Existing asphaltic roof (Optional) Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H- Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board M-OSFA, M- PG1 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 R-53 Existing asphaltic roof (Optional) Min. 1-inch Polytherm or ACFoam II, Polytherm G, ACFoam III, EnergyGuard Polyiso Insulation, ENRGY 3, Polytherm H, H- Shield, ISO 95+ GL, Multi-Max FA3, RESISTA or UltraMax or min. 2-inch Styrofoam Brand Roofmate, Highload 60 or Plazamate M-OSFA, M-PG1 Min. 0.25-inch DensDeck, DensDeck Prime, DEXcell FA Glass Mat Roof Board, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board, min. 7/16-inch DEXcell Cement Roof Board or min. 0.5-inch SECUROCK Cement Roof Board M-OSFA, M- PG1 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2 -157.5 R-54 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch DensDeck Prime, DEXcell FA Glass Mat Roof Board or SECUROCK Gypsum-Fiber Roof Board OB500 SBS-CA1, SBS-CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 R-55 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board OB500 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 R-56 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 OB500 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board OB500 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 R-57 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 (Optional) SBS-CA1, SBS-CA2 SBS-CA1, SBS- CA2, APP-CA1 -120.0 R-58 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or DEXcell FA Glass Mat Roof Board CR-20 SBS-CA1 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 R-59 Existing asphaltic roof (Optional) Min. 1-inch Polytherm, ACFoam II, Polytherm G, ACFoam III, ENRGY 3, Polytherm H, H-Shield or Multi-Max FA3 CR-20 Min. 0.25-inch SECUROCK Gypsum- Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2, APP-CA1 -127.5 NEMO|etc. NEMO ETC, LLC Evaluation Report P9290.02.08-R26 for FL1654-R28 Certificate of Authorization #32455 7TH EDITION (2020) FBC NON-HVHZ EVALUATION Revision 26: 06/09/2021 ©2018 NEMO ETC, LLC Polyglass Modified Bitumen Roof Systems; (954) 233-1330 Appendix 1, Page 98 of 98 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Base Insulation Layer Top Insulation Layer Roof Cover (Note 15) MDP (psf) Type Attach (Notes 6,7,8) Type Attach (Notes 6,7,8) Base Ply Ply Cap Ply R-60 Existing asphaltic roof (Optional) Min. 1-inch ENRGY 3, Polytherm H, H-Shield, Multi-Max FA3 CR-20 Min. 0.25-inch DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA1, SBS-CA2 None SBS-CA1, SBS- CA2 -232.5 TABLE 7B: RECOVER APPLICATIONS SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER System No. Substrate (Notes 1 & 12) Primer Roof Cover (Note 15) MDP (psf) Base Ply Ply Cap Ply R-61 Existing asphaltic roof PG100 BP-AA (Optional if using asphalt applied Ply) (Optional if using asphalt applied Base) BP-AA, SBS- AA, SBS-TA or APP-TA SBS-AA, SBS-TA, APP-TA -45.0 R-62 Existing fully-adhered, granule- surfaced modified bitumen None Polyflex, torch-applied (Optional) Polyflex, torch-applied APP-TA -362.5 R-63 Existing fully-adhered, granule- surfaced modified bitumen PG100 Polyflex, torch-applied (Optional) Polyflex, torch-applied APP-TA -445.0